Preparation and morphological,electrical, and mechanical properties of polyimide‐grafted MWCNT/polyimide composite

Precursor of polyimide, polyamic acid has been prepared sucessfully. Acid‐modified carbon nanotube (MWCNT) was grafted with soluble polyimide then was added to the polyamic acid and heated to 300 °C to form polyimide/carbon nanotube composite via imidation. Morphology, mechanical properties and electrical resistivity of the MWCNT/polyimide composites have been studied. Transmission electron microscope microphotographs show that the diameter of soluble polyimide‐grafted MWCNT was increased from 30–60 nm to 200 nm, that is a thickness of 70–85 nm of the soluble polyimide was grafted on the MWCNT surface. PI‐g‐MWCNT was well dispersed in the polymer matrix. Percolation threshold of MWCNT/polyimide composites has been investigated. PI‐g‐MWCNT/PI composites exhibit lower electrical resistivity than that of the acid‐modified MWCNT/PI composites. The surface resistivity of 5.0 phr MWCNT/polyimide composites was 2.82 × 10⁸ Ω/cm² (PI‐g‐MWCNT) and 2.53 × 10⁹ Ω/cm² (acid‐modified MWCNT). The volume resistivity of 5.0 phr MWCNT/polyimide composites was 8.77 × 10⁶ Ω cm (PI‐g‐MWCNT) and 1.33 × 10¹³ Ω cm (acid‐modified MWCNT).Tensile strength and Young's modulus increased significantly with the increase of MWCNT content. © 2007 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 45: 3349–3358, 2007     

Flame‐retardant epoxy resins with high glass‐transition temperatures. II. Using a novel hexafunctional curing agent: 9,10‐dihydro‐9‐oxa‐10‐phosphaphenanthrene 10‐yl‐tris(4‐aminophenyl) methane

We synthesized a novel phosphorus‐containing triamine [9,10‐dihydro‐9‐oxa‐10‐phosphaphenanthrene 10‐yl‐tris(4‐aminophenyl) methane (dopo‐ta)] from the nucleophilic addition of 9,10‐dihydro‐9‐oxa‐10‐phosphaphenanthrene 10‐oxide and pararosaniline chloride, using triethylamine as an acid receiver. We confirmed the structure of dopo‐ta by IR, mass, and NMR spectra and elemental analysis. dopo‐ta served as a curing agent for diglycidyl ether of bisphenol A (DGEBA) and dicyclopentadiene epoxy (hp7200). Properties such as the glass‐transition temperature (T_g), thermal decomposition temperature, flame retardancy, moisture absorption, and dielectric properties of the cured epoxy resins were evaluated. The T_g's of cured DGEBA/dopo‐ta and hp7200/dopo‐ta were 171 and 190 °C, respectively. This high T_g phenomenon is rarely seen in the literature after the introduction of a flame‐retardant element. The flame retardancy increased with the phosphorus content, and a UL‐94 V‐0 grade was achieved with a phosphorus content of 1.80 wt % for DGEBA/dopo‐ta/diamino diphenylmethane (DDM) systems and 1.46 wt % for hp7200/dopo‐ta/DDM systems. The dielectric constants for DGEBA/dopo‐ta and hp7200/dopo‐ta were 2.91 and 2.82, respectively, implying that the dopo‐ta curing systems exhibited low dielectric properties. © 2005 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 43: 5971–5986, 2005     

Core–shell functionalized MWCNT/poly(m‐aminophenol) nanocomposite with large dielectric permittivity and low dielectric loss

Core–shell carboxyl‐functionalized multiwall carbon nanotube (c‐MWCNT)/poly(m‐aminophenol) (PmAP) nanocomposite were prepared through in‐situ polymerization of m‐aminophenol (m‐AP) in the presence of MWCNTs, and explicated as a dielectric material for electronic applications. The formation of thin PmAP layer on individual c‐MWCNT with excellent molecular level interactions at interfaces was confirmed by morphological and spectroscopic analyses. Here we conducted a comparative study of the dielectric performances of PmAP based nanocomposite films with pristine MWCNTs and c‐MWCNTs as fillers. Compared to PmAP/MWCNT nanocomposites, the PmAP/c‐MWCNT nanocomposites exhibited higher dielectric permittivity and lower dielectric loss. The well dispersed c‐MWCNTs in PmAP/c‐MWCNT nanocomposite produce huge interfacial area together with numerous active polarized centers (crystallographic defects), which in turn intensified the Maxwell‐Wagner‐Sillars (MWS) effect based on excellent molecular level interactions and thus, produce large dielectric permittivity (8810 at 1 kHz). The percolation threshold of PmAP/c‐MWCNT nanocomposites is found lower than that of the PmAP/MWCNT nanocomposites, which could be attributed to homogeneous distribution of c‐MWCNTs and strong c‐MWCNT//PmAP interfacial interactions in the nanocomposites. Copyright © 2016 John Wiley & Sons, Ltd.     

Thermally stable and flame‐retardant aromatic phosphate and cyclotriphosphazene‐containing polyurethanes: synthesis and properties

A novel flame retardant (4‐diphenylphosphoryloxyphenoxy)(4‐hydroxyphenoxy)cyclotriphosphazene (PPPZ) was prepared and characterized by FT‐IR, ³¹P‐NMR and ¹H‐NMR spectroscopy. Polyurethanes that contained aromatic phosphate groups attached to cyclotriphosphazene, with various phosphorus contents, were prepared from PPPZ, poly(propylene glycol), 1,4‐butanediol, and 2,4‐toluene diisocyanate by one‐step polymerization. The polymers prepared were characterized by FT‐IR, thermogravimetric analysis (TGA), differential scanning calorimetry (DSC) and oxygen index (LOI) measurements. The effect of the concentration of PPPZ on the thermal behavior of the polyurethane was studied. The results indicated that the glass transition temperature (T_g) of the polyurethane increased with the concentration of PPPZ. The PPPZ‐containing polyurethanes exhibited slightly higher temperatures of degradation and higher char yields than PPPZ‐free polyurethanes. Moreover, the LOI of the polyurethanes increased with increasing PPPZ content. Also studied was the possible mechanism of the flame retardancy. Copyright © 2005 John Wiley & Sons, Ltd.     

Poly(vinyltriethoxysilane) modified MWCNT/polyimide nanocomposites—Preparation,morphological, mechanical,and electrical properties

Multi‐walled carbon nanotube (MWCNT) modified by vinyltriethoxysilane (VTES) via free radical reaction has been prepared (poly (vinyltriethoxysilane) modified MWCNTs, PVTES‐MWCNT). Precursor of polyimide, polyamic acid has been synthesized by reacting 4,4′‐oxydianiline with 3,3′,4,4′‐benzophenone tetracarboxylic dianhydride. PVTES‐MWCNT were then mixed with polyamic acid and heated to 300 °C to form CNT/polyimide composite. During the imidization processes, the silanes on CNT surface reacted with each other and may be connected together by covalent bond (Si? O? Si). The PVTES‐MWCNT was analyzed by Fourier transform infrared and X‐ray photoelectron spectroscopy. The PVTES‐MWCNT/polyimide composites were analyzed by CP/MAS solid state ²⁹Si nuclear magnetic resonance (NMR) spectroscopy. Morphological properties of the PVTES‐MWCNT/polyimide composites were investigated by scanning electron microscope and transmission electron microscope. Electrical conductivity increased dramatically comparing to the unmodified MWCNT/polyimide composites. Mechanical properties of nanocomposite were enhanced significantly by PVTES‐MWCNT. © 2007 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 46: 803–816, 2008     

Molecular motion,morphology, and thermal properties of multiwall carbon nanotube/polysilsesquioxane composite

Diglycidyl ether of bisphenol A (DGEBA)‐bridged polyorganosiloxane precursors have been prepared successfully by reacting diglycidyl ether of bisphenol A epoxy resin with 3‐aminopropyltriethoxysilane. Acid‐modified and unmodified multiwalled carbon nanotube (MWCNT) were dispersed in the diglycidyl ether of bisphenol A‐bridged polyorganosiloxane precursors and cured to prepare the carbon nanotube/diglycidyl ether of bisphenol A‐bridged polysilsesquioxane (MWCNT/DGEBA‐PSSQ) composites. The molecular motion of MWCNT/DGEBA‐PSSQ nanocomposites was studied by high‐resolution solid‐state ¹³C NMR. Acid‐modification can improve the affinity between MWCNT and the polymer matrix. The molecular motion of the DGEBA‐PSSQ decreased with acid‐modified MWCNT content. However, when unmodified MWCNT was used, the molecular motion of the DGEBA‐PSSQ was increased. SEM and TEM microphotographs confirm that acid‐modified MWCNT exhibits better dispersion than unmodified MWCNT in DGBEA‐PSSQ. The dynamic mechanical properties of acid‐modified MWCNT/DGBEA‐PSSQ composites are more favorable than those of unmodified MWCNT. T_g of the DGEBA‐PSSQ decreased from 174.0 °C (neat DGEBA‐PSSQ) to 159.0 °C (1 wt % unmodified MWCNT) and 156.0 °C (1 wt % acid‐modified MWCNT). The storage modulus (at 30 °C) of the DGEBA‐PSSQ increased from 1.23 × 10⁹ Pa (neat DGEBA‐PSSQ) to 1.65 × 10⁹ Pa (1 wt % acid‐modified MWCNT). However, when unmodified MWCNT was used, the storage modulus of the DGEBA‐PSSQ decreased to 6.88 × 10⁸ Pa (1 wt % unmodified MWCNT). At high temperature, above 150 °C, storage modulus of nanocomposites was higher than that of neat polymer system. © 2008 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 46: 472–482, 2008     

Vanillin‐derived phosphorus‐containing compounds and ammonium polyphosphate as green fire‐resistant systems for epoxy resins with balanced properties

Flame retardants from vanillin when utilized together with ammonium polyphosphate (APP) yield excellent synergistic flame retardancy toward epoxy resins. Bisphenol A epoxy resins have been widely used due to their excellent mechanical properties, chemical resistance, electrical properties, adhesion, etc., while they are flammable. Environment‐friendly and bio‐based flame retardants have captured increasing attention due to their ecological necessity. In this paper, 3 bio‐based flame retardants were synthesized from abundant and more importantly renewable vanillin, and their chemical structures were determined by ¹H NMR and ¹³C NMR. They were used together with APP (an environment‐friendly commercial flame retardant) to improve the fire resistance of bisphenol A epoxy resin. With the addition APP content of 15 phr, the modified bisphenol A epoxy resin could reach UL‐94V0 rating during vertical burning test and limit oxygen index values of above 35%, but reducing APP content to 10 phr, the flame retardancy became very poor. With the total addition content of 10 phr, the epoxy resins modified by 7 to 9 phr APP and 1 to 3 phr bio‐based flame retardants with epoxy groups or more benzene rings showed excellent flame retardancy with UL‐94V0 rating and limit oxygen index values of around 29%. The T_gs of the epoxy resins could be remained or even increased after introducing bio‐based flame retardants, as the control; those of APP alone‐modified epoxy resins compromised a lot. The green synergistic flame‐retardant systems have a great potential to be used in high‐performance materials.     

Investigating properties of poly (ether‐amide)/MWCNT nanocomposite films containing 2,7‐bis(4‐aminophenoxy)naphthalene and isophthalic segments

Three nanocomposite films based on aramid (poly (ether‐amide), PEA) and multiwall carbon nanotubes (MWCNT) were prepared via solution casting method using 2,7‐bis(4‐aminophenoxy)naphthalene (4) and isophthalic acid (5) containing various amounts of MWCNT (2, 3, 5 wt.%). To comprehensively analyze the properties of the cast films as well as the monomers, different techniques were employed, namely FT‐IR, ¹H NMR, X‐ray diffraction, and field emission scanning electron microscopy. Also, thermal and tensile properties of PEA (6) and nanocomposite films were investigated using thermogravimetric analysis and mechanical analysis, respectively. The morphology, thermal, and mechanical properties of nanocomposite films approved that MWCNT had well dispersion in the PEA matrix and showed a synergistic effect on improving all of the investigated properties. Based on the thermogravimetric analysis results, employing MWCNT caused to increase in the char yields from 61 (in the neat PEA) to 66 (in the PEA /MWCNT nanocomposite 5 wt.%) under the nitrogen atmosphere. In comparison to the pristine PEA (426°C), the temperature at 10 losses mass % (T₁₀) was increased from 530°C to 576°C, with 2 to 5 wt.% of MWCNT. Mechanical analysis revealed that the tensile strength and initial modulus were improved by incorporating MWCNT into PEA (81.70–93.40 MPa and 2.10–2.22 GPa, respectively). Electrical conductivity of the PEA/MWCNT nanocomposites was displayed maximum value in the 5 wt.%, showing satisfactory value in many application areas. The X‐ray diffraction technique was employed to study the crystalline structure of the prepared nanocomposite films as well as PEA. In addition, the electrochemical impedance spectroscopy study demonstrated that the prepared nanocomposites had significant impedance improvement in the presence of MWCNTs.     

Development and characterization of fully bio‐based polybenzoxazine‐silica hybrid composites for low‐k and flame‐retardant applications

In the present work, new classes of bio‐based polybenzoxazines were synthesized using eugenol as phenol source and furfurylamine and stearylamine as amine sources separately through solventless green synthetic process routes and were further reinforced with varying percentages (1, 3, 5, and 10 wt%) of silica (from rice husk) to attain hybrid composites. The molecular structure, cure behaviour, thermal stability, dielectric properties, and flame‐retardant behaviour of both benzoxazine monomers and benzoxazine composites were characterized using appropriate modern analytical techniques. The eugenol‐based benzoxazines synthesized using furfurylamine (FBz) and stearylamine (SBz) were cured at 223°C and 233°C, respectively. The differential scanning calorimetry (DSC) data reveal the glass transition temperatures (T_g) of FBz and SBz were 157°C and 132°C, respectively, and the maximum decomposition temperature (T_max) as obtained from thermogravimetric analysis (TGA), were found to be 464°C and 398°C for FBz and SBz, respectively. The dielectric constants for FBz and SBz obtained at 1 MHz were 3.28 and 3.62, respectively. Furthermore, varying weight percentages (1, 3, 5, and 10 wt%) of 3‐mercaptopropyltrimethoxysilane (3‐MPTMS) functionalized bio‐silica reinforced the composite materials as evidenced by their improved thermal stability and lower dielectric constant. Data obtained from thermal and dielectric studies suggested that these polybenzoxazines could be used in the form of adhesives, sealants, and composites for high performance inter‐layer low‐k dielectric applications in microelectronics.     

Comparative study on the properties of poly(trimethylene terephthalate) ‐based nanocomposites containing multi‐walled carbon (MWCNT) and tungsten disulfide (INT‐WS2) nanotubes

Multi‐walled carbon (MWCNT) and tungsten disulfide (INT‐WS₂) nanotubes are materials with excellent mechanical properties, high electrical and thermal conductivity. These special properties make them excellent candidates for high strength and electrically conductive polymer nanocomposite applications. In this work, the possibility of the improvement of mechanical, thermal and electrical properties of poly(trimethylene terephthalate) (PTT) by the introduction of MWCNT and INT‐WS₂ nanotubes was investigated. The PTT nanocomposites with low loading of nanotubes were prepared by in situ polymerization method. Analysis of the nanocomposites' morphology carried out by SEM and TEM has confirmed that well‐dispersed nanotubes in the PTT matrix were obtained at low loading (<0.5 wt%). Thermal and thermo‐oxidative stability of nanocomposites was not affected by the presence of nanotubes in PTT matrix. Loading with INT‐WS₂ up to 0.5 wt% was insufficient to ensure electrical conductivity of PTT nanocomposite films. In the case of nanocomposites filled with MWCNT, it was found that nanotube incorporation leads to increase of electrical conductivity of PTT films by 10 orders of magnitude, approaching a value of 10^?3 S/cm at loading of 0.3 wt%. Tensile properties of amorphous and semicrystalline (annealed samples) nanocomposites were affected by the presence of nanotubes. Moreover, the increase in the brittleness of semicrystalline nanocomposites with the increase in MWCNT loading was observed, while the nanocomposites filled with INT‐WS₂ were less brittle than neat PTT. Copyright © 2016 John Wiley & Sons, Ltd.     

Influence of multiwall carbon nanotube on physical properties of poly(ethylene 2,6‐naphthalate) nanocomposites

Polymer nanocomposites consisting of multiwall carbon nanotube (MWCNT) and poly(ethylene 2,6‐naphthalate) (PEN) were prepared by a melt blending process in a twin‐screw extruder. The storage modulus (G′) and loss modulus (G″) of the PEN/MWCNT nanocomposites increased with increasing frequency, and this increment being more significant at low frequency. The terminal zone slope of G′ for the PEN/MWCNT nanocomposites decreased with increasing MWCNT content, and the nonterminal behavior of those was related to the dominant nanotube–nanotube interactions at higher MWCNT content, leading to the formation of the interconnected or network‐like structures of MWCNT in the polymer nanocomposites. The decrease in the slope of the plot of log G′ versus log G″ for the PEN/MWCNT nanocomposites with increasing MWCNT content suggested the changes in the microstructures of the polymer nanocomposites by incorporating MWCNT. The incorporation of very small quantity of MWCNT significantly improved the mechanical properties of the PEN/MWCNT nanocomposites. © 2006 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 44: 1062–1071, 2006     

Thermal properties and flame retardancy of novel epoxy based on phosphorus‐modified Schiff‐base

Through addition reaction of Schiff‐base terephthalylidene‐bis‐(p‐aminophenol) ( DP‐1 ) and diethyl phosphite (DEP), a novel phosphorus‐modified epoxy, 4,4'‐diglycidyl‐(terephthalylidene‐bis‐(p‐aminophenol))diphosphonate ether ( EP‐2 ), was obtained. An modification reaction between EP‐2 and DP‐1 resulted in an epoxy compound, EP‐3 , possessing both phosphonate groups and C?N imine groups. The structure of EP‐2 was characterized by Fourier transform infrared (FTIR), elemental analysis (EA), ¹H, ¹³C, and ³¹P NMR analyses. The thermal properties of phosphorus‐modified epoxies cured with 4,4'‐diaminodiphenylmethane (MDA) and 4,4'‐diaminodiphenyl ether (DDE) were studied by differential scanning calorimetry (DSC) and thermogravimetric analysis (TGA). The activation energies of dynamic thermal degradation (E_d) were calculated using Kissinger and Ozawa's methods. The thermal degradation mechanism was characterized using thermogravimetric analysis/infrared spectrometry (TG‐IR). In addition, the flame retardancy of phosphorus‐modified epoxy thermosets was evaluated using limiting oxygen index (LOI) and UL‐94 vertical test methods. Via an ingenious design, phosphonate groups were successfully introduced into the backbone of the epoxies; the flame retardancy of phosphorus‐modified epoxy thermosets was distinctly improved. Due to incorporation of C?N imine group, the phosphorus‐modified epoxy thermosets exhibited high thermal stabilities; the values of glass‐transition temperatures (T_gs) were about 201–210°C, the values of E_d were about 220–490 kJ/mol and char yields at 700°C were 49–53% in nitrogen and 45–50% in air. These results showed an improvement in the thermal properties of phosphorus‐modified epoxy by the incorporation of C?N imine groups. Copyright © 2010 John Wiley & Sons, Ltd.     

Preparation, thermal properties, morphology, and microstructure of phosphorus-containing epoxy/SiO2 and polyimide/SiO2 nanocomposites

A phosphorus-containing tri-ethoxysilane (dopo-icteos) reacting from the nucleophilic addition reaction of 9,10-dihydro-9-oxa-10-phosphaphenanthrene 10-oxide (dopo) and 3-(trieoxysilyl) isocyanate (icteos) was synthesized. The structure of dopo-icteos was confirmed by ¹H, ¹³C, ³¹P NMR and IR spectra. A triethylamine catalyzed mechanism for the dopo-icteos synthesis was proposed and verified by NMR spectra. The phosphorus-containing epoxy/SiO₂ and polyimide/SiO₂ nanocomposites were prepared from the in-situ curing of diglycidyl ether of bisphenol A (DGEBA)/4,4-diaminodiphenylmethane(DDM)/dopo-icteos, and imidization of poly(amic acid) of pyromellitic dianhydride (PMDA)/4,4′-oxydianiline (ODA)/dopo-icteos, respectively. The microstructure and morphology were investigated by ²⁹Si NMR, scanning electron microscope (SEM), EDS (Si and P mapping) analysis and atomic force microscope (AFM). The thermal properties, flame retardancy and dielectric properties of the organic-inorganic hybrids were investigated by differential scanning calorimetry (DSC), dynamic mechanical analysis (DMA), limiting oxygen index (LOI), thermal gravimetric analysis (TGA) and dielectric analyzer (DEA).     

Controlled surface‐initiated ring‐opening polymerization of L‐lactide from risedronate‐anchored hydroxyapatite nanocrystals: Novel synthesis of biodegradable hydroxyapatite/poly(L‐lactide) nanocomposites

Risedronate‐anchored hydroxyapatite (HA‐RIS) nanocrystals were prepared with 4.1 wt % RIS and used for controlled surface‐initiated ring‐opening polymerization (ROP) of L ‐lactide (L ‐LA). The strong adsorption of RIS to HA surface not only led to enhanced dispersion of HA nanocrystals in water as well as in organic solvents but also provided alkanol groups as active initiating species for ROP of L ‐LA. HA‐RIS was characterized by thermogravimetric analysis, dynamic light scattering, ¹H NMR, Fourier transform infrared spectrometer, and X‐ray diffraction. The graft polymerization of L ‐LA onto HA‐RIS took place smoothly in the presence of stannous octoate in toluene at 120 °C, resulting in HA/poly(L ‐LA) nanocomposites with high yields of 85–90% and high poly(L ‐LA) contents of up to 97.5 wt %. Notably, differential scanning calorimetry measurements revealed that the poly(L ‐LA) in HA/poly(L ‐LA) nanocomposites exhibited considerably higher melting temperatures (T_m = 173.3?178.1 °C) and higher degrees of crystallinity (X_c = 41.0?43.1%) as compared to poly(L ‐LA) homopolymer (T_m = 168.5 °C, X_c =25.7%). In addition, our initial results showed that these HA/poly(L ‐LA) nanocomposites could readily be electrospun into porous matrices. This study presented a novel and controlled synthetic strategy to HA/RIS/poly(L ‐LA) nanocomposites that are promising for orthopedic applications as well as for bone tissue engineering. © 2011 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2011     

Synthesis and studies of thermal,mechanical and electrical properties of MWCNT–cyclodextrin as a nanoparticle in polyamide matrix based on 2,2‐Bis[4‐(4‐aminophenoxy)phenyl] propane

In the present research, polyamide (PA) ( 6 ) was synthesized by the polycondensation reaction of 2,2‐Bis[4‐(4‐aminophenoxy)phenyl] propane as a diamine ( 4 ) with adipic acid ( 5 ) in the optimized condition. The resulting PA was characterized using Fourier transform infrared spectroscopy, Proton Nuclear Magnetic Resonance (¹H NMR) spectroscopy, inherent viscosity (η_inh), X‐ray diffraction, and solubility tests. Also, the thermal property of the new PA ( 6 ) was investigated by using Thermogravimetric analysis. To apply multiwall carbon nanotube (MWCNT) as an effective reinforcement in polymer composites, it is essential to have appropriate proper dispersion, interfacial adhesion between the MWCNT and polymer matrix, and increasing solubility. With this end particularly, functionalized MWCNTs were combined with a soluble molecule, and a series of modified MWCNT with cyclodextrin (Cy) known as PA/MWCNT‐Cy composite film (2, 5, and 8 wt%) were prepared by a solution intercalation technique. Field emission scanning electron microscopy images showed that MWCNT‐Cy was well dispersed in the PA matrix. Thermogravimetric analysis indicated an increase in thermal stability of nanocomposites as compared with the pristine PA. Anisotropic structure of the synthesized films and dispersed MWCNT‐Cy in the films approved by use of X‐ray diffraction and field emission scanning electron microscopy. The resultant PA/MWCNT‐Cy composite films were electrically conductive, which is favorable for many practical uses. Measurements of mechanical properties of these composite films showed high strength in 8% MWCNT‐Cy content. Also, results showed increases in Young's modulus and tensile strength. Copyright © 2016 John Wiley & Sons, Ltd.     

Low flammability and smoke epoxy resins with a novel DOPO‐based imidazolone derivative

In this work, a DOPO‐based imidazolone derivative named DHI was synthesized using DOPO, 5‐amino‐2‐benzimidazolinone and 4‐hydroxybenzaldehyde as raw materials. The chemical structure of DHI was characterized by ¹H‐NMR, ³¹P‐NMR and Fourier transform infrared spectra (FTIR). Then, a series of different flame‐retardant epoxy resin (EP) thermosets were prepared by mixing flame retardant DHI. The thermal properties of the cured EPs was investigated by thermogravimetry analysis (TGA) and differential scanning calorimeter (DSC), and the results showed the thermal stability and glass transition temperature (T_g) of the cured EP modified with DHI declined slightly compared with that of neat EP. The limited oxygen index (LOI) and UL94 test results exhibited DHI imparted good flame retardancy to EP. The EP‐4 (phosphorus content of 1.25%) possessed a LOI value of 36.5% and achieved a V‐0 rating. Furthermore, the peak of heat release rate (PHRR) and total heat release rate (THR) of EP‐4 decreased by 38.7% and 24.5%, respectively. Excitedly, the total smoke production (TSP) of EP‐4 sample declined by 62.5%, which meant DHI also made EP obtain excellent smoke suppression property. Moreover, the flame‐retardant mechanism was studied by scanning electron microscopy (SEM) and pyrolysis‐gas chromatography/mass spectrometry (Py‐GC/MS). It was reasonable inferred that DHI could not only promote EP to form dense char layer in condensed phase, but also restrain combustion in gaseous phase through catching the free radicals sourced from the degradation of EP.     

Isothermal and nonisothermal crystallization kinetics of nylon 6/functionalized multi‐walled carbon nanotube composites

The well dispersion of functionalized multi‐walled carbon nanotube (f‐MWCNT) in nylon 6 matrix was prepared by solution mixing techniques. The isothermal and nonisothermal crystallization kinetics of nylon 6 and nylon 6/f‐MWCNT nanocomposites were studied by differential scanning calorimetry (DSC), X‐ray diffraction and polarized optical microscopy analysis. DSC isothermal results revealed that the activation energy of nylon 6 extensively decreased by adding 1 wt % f‐MWCNT into nylon 6, suggesting that the addition of small amount of f‐MWCNT probably induces the heterogeneous nucleation. Nevertheless, the addition of more f‐MWCNT into nylon 6 matrix reduced the transportation ability of polymer chains during crystallization process and thus increased the activation energy. The nonisothermal crystallization of nylon 6/f‐MWCNT nanocomposites was also discussed. © 2007 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 46: 158–169, 2008     

Synthesis,characterization, and properties of monodispersed magnetite coated multi‐walled carbon nanotube/polypyrrole nanocomposites synthesized by in‐situ chemical oxidative polymerization

This study describes the preparation of a nanocomposites fabricated from monodispersed 4‐nm iron oxide (Fe₃O₄) coated on the surface of carboxylic acid containing multi‐walled carbon nanotube (c‐MWCNT) and polypyrrole (PPy) by in situ chemical oxidative polymerization. High‐resolution transmission electron microscopy images and X‐ray diffraction (XRD) data indicate that the resulting Fe₃O₄ nanoparticles synthesized using the thermal decomposition are close to spherical dots with a particle size about 4 ± 0.2 nm. The resulting nanoparticles were further mixed with c‐MWCNT in an aqueous solution containing with anionic surfactant sodium bis(2‐ethylhexyl) sulfosuccinate to form one‐dimensional Fe₃O₄ coated c‐MWCNT template for further preparation of nanocomposite. Structural and morphological analysis using field‐emission scanning electron microscopy, high‐resolution transmission electron microscopy, and XRD showed that the fabricated Fe₃O₄ coated c‐MWCNT/PPy nanocomposites are one‐dimensional core (Fe₃O₄ coated c‐MWCNT)‐shell (PPy) structures. The conductivities of these Fe₃O₄ coated c‐MWCNT/PPy nanocomposites are about four times higher than those of pure PPy matrix. © 2008 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 46: 727–733, 2008     

Poly(silarylene–siloxane)polyimides from allyl‐terminated oligoimides and hydride‐functional silarylene–siloxanes via hydrosilylation polymerization

This research was focused on the design and execution of new synthetic routes to low‐temperature‐curable poly(silarylene–siloxane)polyimides. The synthesis of individual oligoimide and silarylene–siloxane blocks was followed by hydrosilylation polymerization to produce crosslinked copolymers. The silarylene–siloxane and polyimide blocks were structurally characterized by IR and ¹H NMR spectroscopy and size exclusion chromatography. The high‐temperature resistance of the copolymers was evaluated through the measurement of heat distortion temperatures (T_HD's) via thermomechanical analysis and by the determination of the weight loss at elevated temperatures via thermogravimetric analysis. Glass‐transition temperatures (T_g's) of the silarylene–siloxane segments were measured by differential scanning calorimetry. Hydrosilylation curing was conducted at 60 °C in the presence of chloroplatinic acid (H₂PtCl₆). The copolymers displayed both high‐temperature resistance and low‐temperature flexibility. We observed T_g of the silarylene–siloxane segment as low as ?77 °C and T_HD of the polyimide segment as high as 323 °C. The influence of various oligoimide molecular weights on the properties of copolymers containing the same silarylene–siloxane was examined. The effect of various silarylene–siloxane molecular weights on the properties of copolymers containing the same oligoimide was also examined. © 2005 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 43: 4922–4932, 2005     

Thermal Degradation Behavior and Kinetic Analysis of Ultra High Molecular Weight Polyethylene Based Multi-Walled Carbon Nanotube Nanocomposites Prepared Via in-situ Polymerization

Thermal degradation behavior of multi-wall carbon nanotubes (MWCNTs)/ultra high molecular weight polyethylene (UHMWPE) nanocomposites, with different nanotubes contents (0.5, 1.5 and 3.5 wt%) prepared via in-situ polymerization technique have been investigated using thermal gravimetric analysis (TGA). TGA spectra revealed that these nanocomposites had enhanced thermal stability and no significant mass loss (<0.4 wt%) occurred up to 350°C. Thermal degradation of these UHMWPE/MWCNT nanocomposites was investigated in terms of parameters such as the onset temperature of degradation (T₁₀), the decomposition temperature at 50% wt loss (T₅₀), the degradation temperature of maximum rate of the weight loss (T_m), and the residual yields (W_R) from TGA. The degradation activation energies (E) of virgin UHMWPE and its nanocomposites were estimated using the Friedman, the Ozawa, Flynn, and Wall (OFW), and the Kissinger's methods. Results indicated that the degradation activation energy for the virgin UHMWPE was 281.3 kJ/mol. The activation energy increased with increasing nanotube loading up to 1.5 wt% indicating that MWCNTs had a stabilizing effect on the degradation of the matrix. However, loadings of 3.5 wt% of nanotube or more could slightly decrease the activation energy. The decrease in the activation energy for degradation of nanocomposites with higher MWCNT concentrations might be attributed to the catalytic effects of nanotubes and polymerization catalyst residues. The “model fitting” method indicated a mechanism of n ^th-order auto-catalysis from the form of the conversion curves for UHMWPE/MWCNTs nanocomposites prepared via in-situ polymerization.