Frontal free‐radical photopolymerization of thick samples: Applications to LED‐induced fiber‐reinforced polymers

Free‐radical photopolymerization is scarcely used for the manufacturing of fiber‐reinforced polymers. The main issue relies on the penetration depth of light which affects the conversion degree when photopolymerizing thick samples. Consequently, this could lead to inhomogeneous polymer properties. The ability of acylphosphine oxides to photobleach under near UV irradiation makes them of great interest for the curing of thick samples. Therefore, the influence of (2,4,6‐trimethylbenzoyl) phosphine oxide on the curing of composites under LED is investigated. Although that a frontal photopolymerization process can be evidenced, it was found that full photobleaching is hardly obtained at high concentration of photoinitiator. Six layers laminates made of unidirectional fiber glass and unsaturated polyester resin were prepared. The existence of an optimal range of concentration for which the conversion of the resin is the most homogeneous throughout its thickness was pointed out, a fact that is confirmed by dynamic mechanical analysis. Interestingly, this effect is reflected in the shrinkage of the resin as shown by direct measurements or deflection experiments. Mechanical analysis was undertaken whose results correlate well with the aforementioned study, demonstrating the occurrence of a balance between the concentration of photoinitiator and the mechanical properties of the samples. © 2019 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2019 , 57, 898–906     

Photo‐triggered redox frontal polymerization: A new tool for synthesizing thermally sensitive materials

A novel approach of photo‐triggered redox frontal polymerization (FP) by integrating photocaged superbase (QA‐DBU) with a peroxide initiator (dibenzoyl peroxide, BPO) is presented for the synthesis of thermally sensitive materials. Under photo‐irradiation at a localized region, the regenerated superbase can diffuse into unirradiated regions and effectively actuate redox FP in a diffusion‐controlled manner. Moreover, the redox FP can be conducted at a much lower front temperature with enhanced front velocity. Astonishingly, the front temperature can be well‐modulated by changing the concentration of latent superbase. The prepared thermally sensitive fluorescent polymer composites exhibit enhanced fluorescence emission intensity compared to that of conventional thermal FP. © 2013 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2013 , 51, 4515–4521     

Dielectric,thermal, and mechanical properties of CeO2‐filled HDPE composites for microwave substrate applications

Cerium oxide‐filled high density polyethylene (HDPE) composites for microwave substrate applications were prepared by sigma‐blend technique. The HDPE was used as the matrix and the dispersion of CeO₂ in the composite was varied up to 0.5 by volume fraction, and the dielectric properties were studied at 1 MHz and microwave frequencies. The variations of thermal conductivity (k_eff), coefficient of thermal expansion (α_c) and Vicker's microhardness with the volume fraction of the filler were also measured. The relative permittivity (ε_eff) and dielectric loss (tan δ) were found to increase with increase in CeO₂ content. For 0.4 volume fraction loading of the ceramic, the composite had ε_eff = 5.7, tan δ = 0.0068 (at 7 GHz), k_eff = 2.6 W/m °C, α_c = 98.5 ppm/°C, Vicker's microhardness of 18 kg/mm² and tensile strength of 14.6 MPa. Different theoretical approaches have been used to predict the effective permittivity, thermal conductivity, and coefficient of thermal expansion of composite systems and the results were compared with the experimental data. © 2010 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 48: 998–1008, 2010     

Biodegradable photocrosslinkable poly(depsipeptide‐co‐ε‐caprolactone) for tissue engineering: Synthesis,characterization, and In vitro evaluation

Stereolithography has become increasingly popular in scaffold fabrication due to automation and well‐controlled geometry complexity, and consequently, there is a great need for new suitable biodegradable photocrosslinkable polymers. In this study, a new type of photocrosslinkable poly(ester amide) was synthesized based on ε‐caprolactone and l ‐alanine‐derived depsipeptide and was applied to fabrication of three‐dimensional (3D) scaffolds by stereolithography. ¹H nuclear magnetic resonance and Fourier transform infra‐red analysis confirmed the formation of new bonds during the polymer synthesis. Incorporation of depsipeptide increased the glass transition temperature and hydrophilicity of the polymer and accelerated hydrolytic degradation compared with the poly(ε‐caprolactone) homopolymer. The compressive strength of the 3D scaffolds increased with the increasing depsipeptide content. This work demonstrated that incorporation of depsipeptide into photocrosslinkable polyesters resulted in excellent cytocompatibility and tunable degradation rates and mechanical properties and thus expanded the repertoire of biomaterials suitable for 3D photofabrication of high‐resolution tissue engineering scaffolds. © 2014 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2014 , 52, 3307–3315     

A novel benzimidazole moiety‐containing benzoxazine: Synthesis,polymerization, and thermal properties

A novel benzoxazine‐containing benzimidazole moiety (P‐PABZ) was synthesized from 2‐(4‐aminophenyl)‐1H‐benzimidazole‐5‐amine and characterized. With the aid of differential scanning calorimetry and in situ Fourier transform infrared, we found the thermal polymerization of P‐PABZ in bulk started around 140 °C and its favored polymerization pathway. Compared to the benzoxazine derived from 4,4′‐diamine diphenyl methane (P‐MDA), P‐PABZ exhibited lower processing temperature, and the corresponding polymers had higher glass transition temperature and enhanced thermal stability. © 2011 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2011     

Solvent‐free inkjet printing process for the fabrication of conductive,transparent, and flexible ionic liquid‐polymer gel structures

A new and solvent‐free process for the fabrication of inkjet printed ionic liquid‐polymer gel microstructures with high‐resolution (line widths of ～40 μm), good electrical conductivity (5–30 mS cm^?1), optical transparency, and mechanical flexibility is presented. Carrying out the printing and polymerization process in nitrogen atmosphere eliminates the inhibiting influence of oxygen and guarantees homogeneously gelled structures. Careful selection and combination of ionic liquids (ILs) and unsaturated monomers makes it possible to achieve low viscosities which are printable with commercially available inkjet printers and printheads without adding extra solvents. By using different types and amounts of ILs and monomers the resulting properties of the printed IL‐polymer gels can be controlled in terms of ionic conductivity, optical transmission, and mechanical flexibility. Higher conductivities are possible by using a bifunctional instead of a monofunctional monomer, which allows one to lower the amount of monomer without loss in mechanical strength. Cast samples make it possible to obtain data of transmission (～90% for 170‐μm thick films) and mechanical flexibility (E = 0.02–0.23 MPa) of bulk material. Comparing electrical conductivity of printed and cast samples, the higher values of printed samples indicate the conductivity enhancing influence of moisture absorbed from the surrounding atmosphere after the fabrication process. © 2011 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys, 2011     

Ring‐opening polymerization of L‐lactide using half‐titanocene complexes of the ATiCl2Nu type: Synthesis,characterization, and thermal properties

Various half‐titanocene complexes of the ATiCl₂Nu type, where A is the pentamethylcyclopentadienyl (Cp*) or indenyl (Ind) group and Nu a nucleophile (ethoxy group or chloride), were used for the polymerization of L ‐lactide, LLA. In the cases where Nu is an ethoxy group, a 5% excess of ATiCl₃ was used to accelerate the polymerization reaction. These systems were proven to be very efficient initiators for the ring‐opening polymerization (ROP) of LLA in toluene at 130 °C. Kinetic studies revealed that in most cases the polymerization yield was quantitative and the molecular weight increased linearly with time, leading to well‐defined PLLA with narrow molecular weight distributions (M_w/M_n ≤ 1.1). LLA was also polymerized by the in situ formation of the initiating system after mixing IndTiCl₃, benzyl alcohol, BzOH, and NEt₃. The thermal properties of the produced polymers were examined by differential scanning calorimetry and thermogravimetric analysis. The activation energy of the thermal decomposition was calculated by the Ozawa–Flynn–Wall and Kissinger methods. © 2012 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2013     

Synthesis of alkaline‐developable,photosensitive hyperbranched polyimides through the reaction of carboxylic acid dianhydrides and trisamines

Hyperbranched polyimides (HBPI)s with high glass‐transition temperatures and excellent thermal stability were synthesized through the reaction of commercially available carboxylic acid dianhydrides with tris[4‐(4‐aminophenoxy)phenyl]ethane (TAPE). In particular, hyperbranched polyimide HBPI(TAPE‐DSDA), prepared through the reaction of TAPE with 3,3′,4,4′‐diphenylsulfonetetracarboxylic dianhydride (DSDA), showed higher thermal stability and good solubility. Furthermore, alkaline‐developable, photosensitive HBPI(TAPE‐DSDA)‐MA‐CA was prepared through the reaction of HBPI(TAPE‐DSDA) with glycidyl methacrylate with tetrabutylammonium bromide as a catalyst in N‐methyl‐2‐pyrrolidinone (NMP) followed by the addition reaction of cis‐1,2,3,6‐tetrahydrophthalic anhydride with triphenylphosphine as a catalyst in NMP. The glass‐transition temperatures of HBPI(TAPE‐DSDA)‐MA‐CA were greater than 300 °C. A resist composed of 74 wt % HBPI(TAPE‐DSDA)‐MA‐CA, 22.2 wt % trimethylpropane triacrylate, and 3.8 wt % Irgacure 907 as a photoinitiator achieved a resolution of a 55‐μm line pattern and a 275‐μm space pattern by UV irradiation (1000 mJ/cm²). © 2004 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 42: 3697–3707, 2004     

Theoretical study on the mechanism for the thermal rearrangement reactions of 2‐silylethyl acetate H3SiCH2CH2OCOCH3

The thermal rearrangement mechanisms of 2‐silylethylacetate H₃SiCH₂CH₂OOCCH₃ were investigated by ab initio molecular orbital theory for the first time. All structures of reactant, transition states, and products were located and fully optimized at the B3LYP/6‐311+G(d, p) levels, and harmonic vibrational frequencies for the involved stationary points on the potential energy surface were obtained. The reaction pathways were analyzed and confirmed by intrinsic reaction coordinate (IRC) calculations. Furthermore, atomic charges were determined by using the natural bond orbital (NBO) analysis. The calculational results show that H₃SiCH₂CH₂OOCCH₃ can rearrange thermally in two ways. One is [1,3] rearrangement (Reaction A), in which silyl group transfers from carbon to oxygen(in C? O? C) via a four‐membered ring transition state, forming silyl acetate and ethylene, the other way, [1,5] rearrangement (Reaction B), happens with transferring of silyl group from carbon to oxygen (in C?O) via a six‐membered ring transition state, forming the same products as in Reaction A. The energy barriers of the Reactions A and B were calculated to be 188.9 and 191.6 kJ/mol at the B3LYP/6‐311+G(d,p) levels, respectively. Changes in thermodynamic functions (ΔS, ΔH, and ΔG), equilibrium constant K(T), as well as preexponential factor A(T), and reaction rate constant k(T) in Eyring transition state theory were calculated over a temperature range of 200–1600 K, and then thermodynamic and kinetic properties of the reactions were analyzed. It can be suggested that Reactions A and B are noncompetitive, and both happen only at elevated temperature. © 2008 Wiley Periodicals, Inc. Int J Quantum Chem, 2009     

3‐D graphene‐supported mesoporous SiO2@Fe3O4 composites for the analysis of pesticides in aqueous samples by magnetic solid‐phase extraction with high‐performance liquid chromatography

Three‐dimensional graphene‐supported mesoporous silica@Fe₃O₄ composites (mSiO₂@Fe₃O₄‐G) were prepared by modifying mesoporous SiO₂‐coated Fe₃O₄ onto hydrophobic graphene nanosheets through a simple adsorption co‐condensation method. The obtained composites possess unique properties of large surface area (332.9 m²/g), pore volume (0.68 cm³/g), highly open pore structure with uniform pore size (31.1 nm), as well as good magnetic separation properties. The adsorbent (mSiO₂@Fe₃O₄‐G) was used for the magnetic solid‐phase extraction of seven pesticides with benzene rings in different aqueous samples before high‐performance liquid chromatography. The main parameters affecting the extraction such as adsorbent amount, volume of elution solvent, time of extraction and desorption, salt effect, oscillation rate were investigated. Under the optimal conditions, this method provided low limits of detection (S/N = 3, 0.525–3.30 μg/L) and good linearity (5.0–1000 μg/L, R² > 0.9954). Method validation proved the feasibility of the developed adsorbent, which has a high extraction efficiency and excellent enhancement performance for pesticides in this study. The proposed method was successfully applied to real aqueous samples, and satisfactory recoveries ranging from 77.5 to 113.6% with relative standard deviations within 9.7% were obtained.     

A Cantilever‐based Biosensor for Real‐time Monitoring of Interactions between Amyloid‐β(1–40) and Membranes Comprised of Phosphatidylcholine Lipids with Different Hydrophobic Acyl Chains

Accumulating evidence suggests that interaction between amyloid‐β (Aβ) and cell membrane is crucial to the pathogenesis of Alzheimer's disease (AD), and thus an increasing understanding of the impact of membrane composition on Aβ‐membrane interaction becomes essential for the mechanism elucidation of Aβ‐membrane interaction and the early diagnosis of AD. In this work, electrically neutral phosphatidylcholine (PC) as the most major class of membrane phospholipids, including 1,2‐dipalmitoyl‐sn‐glycero‐3‐phosphocholine (DPPC), 1,2‐distearoyl‐sn‐glycero‐3‐phosphocholine (DSPC), 1‐palmitoyl‐2‐oleoyl‐sn‐glycero‐3‐phosphocholine (POPC), and Aβ(1–40) as the most common amyloid protein were selected as the research subjects, and a developed cantilever‐based biosensor, on which liposomes comprised of PC lipids were immobilized, was applied to characterize in real time the interactions between Aβ(1–40) and membranes comprised of PC lipids with different hydrophobic acyl chains, and to evaluate the effect of cholesterol incorporated in membrane on Aβ‐membrane interaction during the whole process of Aβ(1–40) fibrillization. The results illustrate that the interaction between Aβ(1–40) and PC membrane can be divided into three stages, which are related to the change in molecular states of Aβ. More importantly, it is found that membranes comprised of PC lipids with shorter saturated acyl chains show higher interaction ability with Aβ(1–40), and the incorporation of cholesterol into PC bilayer can remarkably accelerate and strengthen Aβ(1–40)‐membrane interaction. These results confirm that hydrophobicity is the main driving force for the interactions between Aβ(1–40) and PC membranes. In return, the above results enlightened us to apply the current micro‐cantilever immobilized with cholesterol‐containing DPPC liposomes to challenge the detection of low‐concentration Aβ(1–40). This time 50‐nM Aβ(1–40) in aqueous solution has been effectively detected, suggesting that this proposed detection technique would contribute to Aβ detection and early diagnosis of AD in the future.     

Influence of the film‐forming process on the nanostructuration of Pebax®/1‐ethyl‐3‐methylimidazolium triflate ionic liquid: Consequences on the thermal,mechanical, gas,and water transport properties

1‐Ethyl‐3‐methylimidazolium triflate ionic liquid (IL) was incorporated in Pebax® MV 3000 copolymer through solvent cast (SC) or melt blending (MB) for composition from 0 to 30 wt % IL. The morphology was investigated by small angle neutron scattering, transmission electron microscopy, and differential scanning calorimetry. The SC copolymer film exhibited a lower mean correlation distance (D = 87 Å) and smoother transition between the rigid and soft phases in comparison with the MB film (D = 103 Å). By dissolving in the copolymer soft phase, IL acted as a plasticizer, impeded soft segments crystallization and led to linear increase of D. The differences observed in morphology as a function of the film process impacted the mechanical and gas transport properties: below 20 wt % IL, all SC films sustained thermomechanical properties up to 120 °C and exhibited lower permeability than MB films. IL adding made permeability decrease up to 60%, depending on the gas nature and IL amount. Hydration of the films was investigated by sorption and SANS analyses. The impact of water uptake on swelling was similar for all membranes whereas water diffusion depended on the film morphologies and IL amount. Interesting mechanical and transport properties were obtained for IL content up to 20 wt %. © 2017 Wiley Periodicals, Inc. J. Polym. Sci., Part B: Polym. Phys. 2017 , 55, 778–788     

Bis(β‐diketiminato) lanthanide amides: synthesis,structure and catalysis for the polymerization of l‐lactide and ε‐caprolactone

Treatment of the chlorides (L^2,6‐iPr2_Ph)₂LnCl (L^2,6‐iPr2_Ph = [(2,6‐ⁱPr₂C₆H₃)NC(Me)CHC(Me)N(C₆H₅)]^?) with 1 equiv. of NaNH(2,6‐ⁱPr₂C₆H₃) afforded the monoamides (L^2,6‐iPr2_Ph)₂LnNH(2,6‐ⁱPr₂C₆H₃) (Ln = Y ( 1 ), Yb ( 2 )) in good yields. Anhydrous LnCl₃ reacted with 2 equiv. of NaL^2,6‐iPr2_Ph in THF, followed by treatment with 1 equiv. of NaNH(2,6‐ⁱPr₂C₆H₃), giving the analogues (L^2,6‐iPr2_Ph)₂LnNH(2,6‐ⁱPr₂C₆H₃) (Ln = Sm ( 3 ), Nd ( 4 )). Two monoamido complexes stabilized by two L^2‐Me ligands, (L^2‐Me)₂LnNH(2,6‐ⁱPr₂C₆H₃) (L^2‐Me = [N(2‐MeC₆H₄)C(Me)]₂CH)^?; Ln = Y ( 5 ), Yb ( 6 )), were also synthesized by the latter route. Complexes 1 , 2 , 3 , 4 , 5 , 6 were fully characterized, including X‐ray crystal structure analyses. Complexes 1 , 2 , 3 , 4 , 5 , 6 are isostructural. The central metal in each complex is ligated by two β‐diketiminato ligands and one amido group in a distorted trigonal bipyramid. All the complexes were found to be highly active in the ring‐opening polymerization of L‐lactide (L‐LA) and ε‐caprolactone (ε‐CL) to give polymers with relatively narrow molar mass distributions. The activity depends on both the central metal and the ligand (Yb < Y < Sm ≈ Nd and L^2‐Me < L^2,6‐iPr2_Ph). Remarkably, the binary 3/benzyl alcohol (BnOH) system exhibited a striking ‘immortal’ nature and proved able to quantitatively convert 5000 equiv. of L‐LA with up to 100 equiv. of BnOH per metal initiator. All the resulting PLAs showed monomodal, narrow distributions (M_w/M_n = 1.06 ? 1.08), with molar mass (M_n) decreasing proportionally with an increasing amount of BnOH. The binary 4/BnOH system also exhibited an ‘immortal’ nature in the polymerization of ε‐CL in toluene. Copyright © 2014 John Wiley & Sons, Ltd.     

Molecularly imprinted microspheres for the anticancer drug aminoglutethimide: Synthesis,characterization, and solid‐phase extraction applications in human urine samples

Molecularly imprinted microspheres (MIMs) for the anticancer drug aminoglutethimide (AG) were synthesized by aqueous suspension polymerization. The expected size and diameter of MIMs are controlled easily by changing one of the surfactant types, ratio of organic‐to‐water phase or stirring rate during polymerization. The obtained MIMs exhibit specific affinity toward AG with imprinting factor of 3.11 evaluated with a chromatographic model. The resultant MIMs were used as the SPE materials for the extraction of AG from human urine. A molecularly imprinted SPE (MISPE) method coupled with HPLC has been developed for the extraction and detection of AG in urine. Our results showed that most impurities from urine can be removed effectively after a washing step and the AG has been enriched effectively after MISPE operation with the recovery of >90% (n = 3). The developed MISPE–HPLC method could be used for enrichment and detection of AG in human urine.     

Role,effect, and influences of micro and nano‐fillers on various properties of polymer matrix composites for microelectronics: A review

Ever since the discovery of polymer composites, its potential has been anticipated for numerous applications in various fields such as microelectronics, automobiles, and industrial applications. In this paper, we review filler reinforced polymer composites for its enormous potential in microelectronic applications. The interface and compatibility between matrix and filler have a significant role in property alteration of a polymer nanocomposites. Ceramic reinforced polymeric nanocomposites are promising candidate dielectric materials for several micro‐ and nano‐electronic devices. Because of its synergistic effect like high thermal conductivity, low thermal expansion, and dielectric constant of ceramic fillers with the polymer matrix, the resultant nanocomposites have high dielectric breakdown strength. The thermal and dielectric properties are discussed in the view of filler alignment techniques and its effect on the composites. Furthermore, the effect of various surface modified filler materials in polymer matrix, concepts of network forming using filler, and benefits of filler alignment are also discussed in this work. As a whole, this review article addresses the overall view to novice researchers on various properties such as thermal and dielectric properties of polymer matrix composites and direction for future research to be carried out.     

A New Mechanism for β‐Lactamases: Class D Enzymes Degrade 1β‐Methyl Carbapenems through Lactone Formation

β‐Lactamases threaten the clinical use of carbapenems, which are considered antibiotics of last resort. The classical mechanism of serine carbapenemase catalysis proceeds through hydrolysis of an acyl‐enzyme intermediate. We show that class D β‐lactamases also degrade clinically used 1β‐methyl‐substituted carbapenems through the unprecedented formation of a carbapenem‐derived β‐lactone. β‐Lactone formation results from nucleophilic attack of the carbapenem hydroxyethyl side chain on the ester carbonyl of the acyl‐enzyme intermediate. The carbapenem‐derived lactone products inhibit both serine β‐lactamases (particularly class D) and metallo‐β‐lactamases. These results define a new mechanism for the class D carbapenemases, in which a hydrolytic water molecule is not required.     

Tuning the Reactivity of N,O,O,O‐Non‐Metallocene Catalysts for α‐Olefin Polymerization: Issues Related to Ligand Symmetry and Derivatization

Summary: Titanium‐based precatalysts, bearing C₃ or pseudo‐C_s symmetric aminotriol ligands, upon activation with methylaluminoxane, polymerize hex‐1‐ene to give polymers of high molecular weight, i.e., 50 000 and 600 000, respectively, with low dispersity, 1.2–1.4, and high isotacticity, 85–60%, depending on the overall symmetry of the precatalysts, but when one arm of the aminotriol ligands is methylated to yield C₂ or meso aminodiol ligands, their corresponding titanium catalysts gave higher‐molecular‐weight polyhexenes, 300 000 to 250 000, with lower dispersities, 1.07–1.11, which possibly suggests living polymerization, with activities 200–500 times greater than that of the parent C₃ and pseudo‐C_s catalysts.

     

Syndiotactic‐specific radical polymerization of N,N‐dimethylacrylamide in the presence of tartrates: A proposed mechanism for the polymerization

Radical polymerization of N,N‐dimethylacrylamide (DMAAm) was investigated in the presence of tartrates, such as diethyl L ‐tartrate, diisopropyl L ‐tartrate, and di‐n‐butyl L ‐tartrate, in toluene at low temperatures. Syndiotactic polymers were obtained in the presence of tartrates, whereas isotactic polymers were obtained in the absence of tartrates. The syndiotactic‐specificity increased with increasing amount of tartrates and with decreasing polymerization temperature. NMR analysis suggested that DMAAm and tartrates formed a 1:1 complex through double hydrogen bonding. A mechanism for the syndiotactic‐specific radical polymerization of DMAAm is proposed. © 2009 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 47: 1192–1203, 2009