Bismuth telluride topological insulator nanosheet saturable absorbers for q‐switched mode‐locked Tm:ZBLAN waveguide lasers

Nanosheets of bismuth telluride (Bi₂Te₃), a topological insulator material that exhibits broadband saturable absorption due to its non‐trivial Dirac‐cone like energy structure, are utilized to generate short pulses from Tm:ZBLAN waveguide lasers. By depositing multiple layers of a carefully prepared Bi₂Te₃ solution onto a glass substrate, the modulation depth and the saturation intensity of the fabricated devices can be controlled and optimized. This approach enables the realization of saturable absorbers that feature a modulation depth of 13% and a saturation intensity of 997 kW/cm². For the first time to our knowledge, Q‐switched mode‐locked operation of a linearly polarized mid‐IR ZBLAN waveguide chip laser was realized in an extended cavity configuration using the topological insulator Bi₂Te₃. The maximum average output power of the laser is 16.3 mW and the Q‐switched and mode‐locked repetition rates are 44 kHz and 436 MHz, respectively.     

Growth behavior of Bi2Te3 and Sb2Te3 thin films on graphene substrate grown by plasma‐enhanced chemical vapor deposition

A comparative study of the substrate effect on the growth mechanism of chalcogenide Bi₂Te₃ and Sb₂Te₃ thin films was carried out. Obvious microstructural discrepancy in both the as‐deposited Bi₂Te₃ and Sb₂Te₃ thin films was observed when grown on graphene or SiO₂/Si substrate. Bi₂Te₃ and Sb₂Te₃ thin films deposited on the graphene substrate were observed to be grown epitaxially along c‐axis and show very smooth surface compared to that on SiO₂/Si substrate. Based on the experimental results of this study, the initial adsorption sites on graphene substrate during deposition process, which had been discussed theoretically, could be demonstrated empirically.     

Fundamental band edge optical absorption in Bi<Subscript>0.5</Subscript>Sb<Subscript>1.5</Subscript>Te<Subscript>3</Subscript>

Spectra of optical absorption in Bi_0.5Sb_1.5Te₃ films grown on mica and KBr substrates have been investigated for T = 145 and 300 K. The data obtained have been analyzed together with the data of investigations on the fundamental absorption edge for Bi₂Te₃ available in the scientific literature. It has been revealed that the interband absorption spectra for both Bi_0.5Sb_1.5Te₃ and Bi₂Te₃ represent a superposition of two components corresponding to direct and indirect allowed optical transitions. In this case, the least energy gap separating the valence band and the conduction band is direct for Bi_2−xSb_xTe₃ (x ≤ 1.5, T = 300 K). For Bi_0.5Sb_1.5Te₃ the temperature variation rates have been estimated for the thresholds of direct and indirect interband transitions. It has been shown that this solid solution is direct gap solution at T ≥ 145 K. Translated from Izvestiya Vysshikh Uchebnykh Zavedenii, Fizika, No. 7, pp. 50–52, July, 2008.     

Electronic structures and thermoelectric properties of La or Ce-doped Bi2Te3 alloys from first principles calculations

Thermoelectric properties of La or Ce-doped Bi₂Te₃ alloys were systematically investigated by ab initio calculations of electronic structures and Boltzmann transport equations. The Seebeck coefficient of p-type LaBi₇Te₁₂ and La₂Bi₆Te₁₂ was larger than that of Bi₂Te₃, because La doping increased the effective mass of carriers. On the other hand, the electrical conductivity of LaBi₇Te₁₂ and La₂Bi₆Te₁₂ decreased, which caused a reduction of power factor of these La-doped Bi₂Te₃ alloys in comparison with Bi₂Te₃. The influence of Ce doping on the band structure and thermoelectric properties of Bi₂Te₃ was similar to that of La doping. The theoretical calculation provided an insight into the transport properties of La or Ce-doped Bi₂Te₃-based thermoelectric materials.     

Thermoelectric properties of Bi2Se3/Bi2Te3/Bi2Se3 and Sb2Te3/Bi2Te3/Sb2Te3 quantum well systems

In this work, we develop a theory of thermoelectric transport properties in two-dimensional semiconducting quantum well structures. Calculations are performed for n-type 0.1 wt.% CuBr-doped Bi₂Se₃/Bi₂Te₃/Bi₂Se₃ and p-type 3 wt.% Te-doped Sb₂Te₃/Bi₂Te₃/Sb₂Te₃ quantum well systems in the temperature range 50–600 K. It is found that reducing the well thickness has a pronounced effect on enhancing the thermoelectric figure of merit (ZT). For the n-type Bi₂Se₃/Bi₂Te₃/Bi₂Se₃ with 7 nm well width, the maximum value of ZT is estimated to be 0.97 at 350 K and for the p-type Sb₂Te₃/Bi₂Te₃/Sb₂Te₃ with well width 10 nm the highest value of the ZT is found to be 1.945 at 440 K. An explanation is provided for the resulting higher ZT value of the p-type system compared to the n-type system.     

Plasma screening of the fundamental absorption edge in crystals of Bi2Te3-Sb2Te3 solid solutions with more than 80 mol % Sb2Te3

The regularities of changes in the optical properties of crystals of Bi₂Te₃-Sb₂Te₃ solid solutions in the range of the effects caused by free-carrier plasma oscillations at a variation in the ratio of Bi₂Te₃ and Sb₂Te₃ components are investigated. It is established that, when the Sb₂Te₃ content in a solid solution exceeds 80 mol %, the fundamental absorption edge undergoes plasma screening. Doping a Sb₂Te₃ crystal with tin increases the free-carrier concentration and plasma frequencies, thus enhancing the screening effect, whereas introduction of 0.1 mol % selenium reduced the plasma frequency and thus removes the fundamental-absorption-edge screening.     

Temperature dependence of the Raman spectra of Bi2Te3 and Bi0.5Sb1.5Te3 thermoelectric films

The temperature dependence of the Raman spectra of Bi₂Te₃ and Bi_0.5Sb_1.5Te₃ thermoelectric films was investigated. The temperature coefficients of the E_g(2) peak positions were determined as –0.0137 cm^–1/°C and –0.0156 cm^–1/°C, respectively. The thermal expansion of the crystal caused a linear shift of the Raman peak induced by the temperature change. Based on the linear relation, a reliable and noninvasive micro‐Raman scattering method was shown to measure the thermal conductivity of the thermoelectric films. (© 2012 WILEY‐VCH Verlag GmbH & Co. KGaA, Weinheim)     

Defect structure of Bi2−xAsxTe3 single crystals

Single crystals Bi_2−xAs_xTe₃ were prepared by a modified Bridgman technique. The samples were characterized by X-ray diffraction analyses and measurement of Hall coefficient and electrical conductivity. Atomic absorption spectroscopy (AAS) was used for determination of actual content of As in the samples. The doping of Bi₂Te₃ with As leads to a decrease of the free carriers concentration while their mobility increases. The observed effects are discussed within a point defect model of Bi_2−xAs_xTe₃ crystals.     

Effect of nanocrystallinity on lattice dynamics in Bi2Te3 based thermoelectrics

The lattice dynamics in as‐cast and nanocrystalline thermoelectric Bi₂Te₃ based p‐type and n‐type material were investigated using inelastic neutron scattering. Generalized densities of phonon states show substantial agreement between the lattice dynamics in as‐cast samples and previous studies. The lattice dynamics in the nanocrystalline materials differ significantly from its as‐cast counterparts in the acoustic phonon regime. In nanocrystalline p‐type and n‐type compounds, the average acoustic phonon group velocity was found to be reduced to 80(5)% and 95(2)% of the value in as‐cast material. It is argued that point‐defect and strain contrast scattering may play an important role for the understanding of lattice thermal conductivity in (nanocrystalline) Bi₂Te₃ based thermoelectrics beside the observed decrease of sound velocity. (© 2015 WILEY‐VCH Verlag GmbH &Co. KGaA, Weinheim)     

Changes in the electronic properties of Bi2X3 (X: Se, Te) single crystals due to intercalation

Bi₂Se₃ and Bi₂Te₃ are layered semiconductors n-type and p-type, respectively, which belong to the family of thermoelectric materials. In this work we examine the insertion of Cu in Bi₂Te₃ and Bi₂Se₃ single crystals through an intercalation reaction. The inserted Cu acting as donor enhances the n-type character of Bi₂Se₃ while changing the native p-type character of Bi₂Te₃ to n-type. The spatial distribution of the intercalated species was monitoring by X-ray microanalysis and microscopic IR reflectivity measurements. Paper presented at the 4th Euroconference on Solid State Ionics, Renvyle, Galway, Ireland, Sept. 13–19, 1997     

粗糙界面对Bi2Te3/PbTe超晶格热电优值影响的理论分析

以Bi₂Te₃/PbTe超晶格薄膜为例,分析电子在Bi₂Te₃量子阱中的输运过程,综合了薄膜的经典散射效应和理想量子效应,并以此混合效应为基础,在PbTe障碍层厚度一定时,模拟计算了两种混合效应中量子效应占不同比例时,Bi₂Te₃/PbTe超晶格热电优值的变化.在镜面反射占混合效应的0.3时,得到的热电优值与当前报道的量子阱超晶格的实验值接近. 关键词： 超晶格 粗糙界面 热电优值     

Superconductivity and non-metallicity induced by doping the topological insulators Bi2Se3 and Bi2Te3

We show that by Ca doping the Bi₂Se₃ topological insulator, the Fermi level can be fine tuned to fall inside the band gap and therefore suppresses the bulk conductivity. Non-metallic Bi₂Se₃ crystals are obtained. On the other hand, the Bi₂Se₃ topological insulator can also be induced to become a bulk superconductor, with T_c∼3.8 K, by copper intercalation in the van der Waals gaps between the Bi₂Se₃ layers. Likewise, an as-grown crystal of metallic Bi₂Te₃ can be turned into a non-metallic crystal by slight variation in the Te content. The Bi₂Te₃ topological insulator shows small amounts of superconductivity with T_c∼5.5 K when reacted with Pd to form materials of the type Pd_zBi₂Te₃.     

Thermoelectric performance of monolayer Bi2Te2Se of ultra low lattice thermal conductivity

The electronic structure and thermoelectric properties of monolayer Bi₂Te₂Se were studied by density functional theory and semi-classical Boltzmann transport equation. The band gap with TB-mBJ can be improved for monolayer Bi₂Te₂Se. Monolayer Bi₂Te₂Se have ultra-low thermal conductivity comparing with other well-known two-dimensional materials. The monolayer Bi₂Te₂Se can improve electrical conductivities. ZT increases with increasing temperature for monolayer Bi₂Te₂Se. Comparing to GGA, TB-mBJ has larger ZT value in p-type doping. Monolayer Bi₂Te₂Se have larger ZT comparing with other well-known two-dimensional materials. Our calculated results show that our calculation greatly underestimates ZT value, therefore, monolayer Bi₂Te₂Se should have a higher ZT value.     

Characterization of Mn-doped Sb1.5Bi0.5Te3 single crystals

Abstract

Single crystals of (Sb_0.75Bi_0.25)_2-xMn_xTe₃ (x = 0.0–0.05) were characterized by X-ray diffraction, measurements of reflectance in the plasma resonance frequency region, Hall coefficient, electrical conductivity, and Seebeck coefficient. It was found that Mn atoms in the crystal structure of Sb_1.5Bi_0.5Te₃ behave like acceptors; the increase in the hole concentration is explained by the formation of substitutional defects of Mn'_Sb and Mn'_Bi in the crystal lattice of the studied crystals.     

Electrochemical deposition of Bi2Te3-based thin films

The electrochemical reduction processes on stainless-steel substrates from an aqueous electrolyte composed of nitric acid, Bi³⁺, HTeO₂⁺, SbO⁺ and H₂SeO₃ systems were investigated using cyclic voltammetry. The thin films with a stoichiometry of Bi₂Te₃, Bi_0.5Sb_1.5Te₃ and Bi₂Te_2.7Se_0.3 have been prepared by electrochemical deposition at selected potentials. The structure, composition, and morphology of the films were studied by X-ray diffraction (XRD), environmental scanning electron microscopy (ESEM) and electron microprobe analysis (EMPA). The results showed that the films were single phase with the rhombohedral Bi₂Te₃ structure. The morphology and growth orientation of the films were dependent on the deposition potentials.     

Optical and thermoelectric characterizations of electroplated n-Bi2(Te0.9Se0.1)3

Bismuth selenotelluride (Bi₂(Te_0.9Se_0.1)₃) films were electrodeposited at constant current density from acidic aqueous solutions with Arabic gum in order to produce thin films for miniaturized thermoelectric devices. X-ray fluorescence spectroscopy determined film compositions. X-ray diffraction pattern shows that the films as deposited are polycrystalline, isostructural to Bi₂Te₃ and covered by crystallites. Mueller-matrix analysis reveals that the electroplated layers are optically like an isotropic medium. Their pseudo-dielectric functions were determined using mid-infrared spectroscopic ellipsometry. Tauc-Lorentz combined with Drude dispersion relations were successfully used. The energy band gap E_g was found to be about 0.15 eV. Moreover, the fundamental absorption edge was described by an indirect optical band-to-band transition. From Seebeck coefficient measurement, films exhibit n-type charge carrier and the value of thermoelectric power is about −40 μV/K.     

Density functional study of Bi2Te3 and Bi4Te6 molecules

Results of a density functional study for the molecules Bi₂Te₃ and Bi₄Te₆ are reported here. For Bi₂Te₃, calculations yield eight stable conformations. For Bi₄Te₆, eight stable isomers are identified. Equilibrium geometries, adiabatic ionisation potentials, atomisation energies, and vibrational bands are estimated. The lowest energy conformations in both cases are clusters of C_s symmetry with all Te atoms two-fold coordinated and all Bi atoms three-fold coordinated. The predicted low energy conformation for Bi₄Te₆ has alternating rows of Bi and Te atoms. This molecule seems a reasonable precursor to solid bismuth telluride, which has alternating Bi and Te layers.     

Development of Novel Graphene/g‐C3N4 Composite with Broad‐Frequency and Light‐Weight Features

In this study, a novel graphene/g‐C₃N₄ microwave absorber is developed to solve the electromagnetic wave interference problem. Graphene/g‐C₃N₄ composite is synthesized by loading g‐C₃N₄ nanosheets on graphene through a simple liquid‐phase approach. High‐performance electromagnetic absorption performance can be achieved. The optimal reflection loss value is up to ?29.6 dB under a thin coating layer of 1.5 mm. At the same time, the corresponding absorption bandwidth of this composite can reach 5.2 GHz (12.8–18 GHz). Excellent electromagnetic absorption property may be attributed to the current attenuation theory which has been proven by replacing graphene with porous graphene or graphene oxide. The results reveal that free electron numbers and loading mass of g‐C₃N₄ on graphene play the key roles in the intensity of current attenuation and resistance value.     

Thermoelectric properties of nano-bulk bismuth telluride prepared with spark plasma sintered nano-plates

The pursuit for a high-performance thermoelectric n-type bismuth telluride-based material is significant because n-type materials are inferior to their corresponding p-type materials in highly efficient thermoelectric modules. Herein, to improve the thermoelectric performance of an n-type Bi₂Te₃, we prepared Bi₂Te₃ nano-plates with a homogeneous sub-micron size distribution and thickness range of about a few tens of nanometers. This was achieved using a typical nano-chemical synthetic method, and the prepared materials were then spark plasma sintered to fabricate n-type nano-bulk Bi₂Te₃ samples. We observed a significant enhancement of the anisotropic electrical transport properties for the nano-bulk sample with a higher power factor along the in-plane direction (24.3?μW?cm^?1?K^?2 at 300?K) than that along the out-of-plane direction (8.1?μW?cm^?1?K^?2 at 300?K). However, thermal transport properties were insensitive along the measured direction for the nano-bulk sample. We used a dimensionless figure of merit ZT to calculate the thermoelectric performance. The results showed that the maximum ZT value of 0.69 was achieved along the in-plane direction at 440?K for the nano-bulk n-type Bi₂Te₃ sample, which was however smaller than that of the previously reported n-type samples (ZT of 1.1). We believe that a further enhancement of the ZT value in the fabricated nano-bulk sample could be accomplished by effectively removing the surface organic ligand of the Bi₂Te₃ nano-plate particles and optimizing the spark plasma sintering conditions, maintaining the nano-plate morphology intact.     

Solvothermal preparation and characterization of nanocrystalline Bi2Te3 powder with different morphology

Bi₂Te₃-based alloys are currently best-known, technological important thermoelectric materials near room temperature. In this paper, nanocrystalline Bi₂Te₃ with different morphologies was synthesized by a solvothermal process based on the reaction between BiCl₃, Te, and KBH₄ in N,N-dimethylformamide at 100-180 °C. KBH₄ was used as a reducing agent. The products were characterized by X-ray diffraction and transmission electron microscopy (TEM). The particle morphologies and size are dependent on the reaction temperature and time. A possible formation mechanism is proposed.