Influence of Polymer Electronics on Selective Dispersion of Single‐Walled Carbon Nanotubes

The separation and isolation of semiconducting and metallic single‐walled carbon nanotubes (SWNTs) on a large scale remains a barrier to many commercial applications. Selective extraction of semiconducting SWNTs by wrapping and dispersion with conjugated polymers has been demonstrated to be effective, but the structural parameters of conjugated polymers that dictate selectivity are poorly understood. Here, we report nanotube dispersions with a poly(fluorene‐co‐pyridine) copolymer and its cationic methylated derivative, and show that electron‐deficient conjugated π‐systems bias the dispersion selectivity toward metallic SWNTs. Differentiation of semiconducting and metallic SWNT populations was carried out by a combination of UV/Vis‐NIR absorption spectroscopy, Raman spectroscopy, fluorescence spectroscopy, and electrical conductivity measurements. These results provide new insight into the rational design of conjugated polymers for the selective dispersion of metallic SWNTs.     

The effect of length of single‐walled carbon nanotubes (SWNTs) on electrical properties of conducting polymer–SWNT composites

DC conductivity of conjugated polymer‐single‐walled carbon nanotube (SWNT) composite films has been measured for different SWNT concentrations. The composite was prepared by dispersing SWNTs in the poly (3‐octylthiophene), P3OT matrix already dissolved in xylene. The conductivity of the composite films showed a rapid increase as the SWNT concentration increases beyond a certain value. This behavior is explained in terms of percolating paths provided by the SWNTs in the volume of polymer matrix. To investigate the effect of length of nanotubes on the percolation conductivity, different SWNT samples were employed with similar diameter but varying tube lengths. It was found that the conductivity of the composite films is strongly dominated by the length of the nanotubes. Lower percolation limit and high conductivity value of composite films is observed for longer nanotubes. Furthermore, the conductivity is observed to be dependent on the size of the host polymer molecule also. © 2009 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 48: 89–95, 2010     

Dendronized polymers via Diels–Alder “click” reaction

A modular approach toward the synthesis of polymers containing dendron groups as side chains is developed using the Diels–Alder “click” reaction. For this purpose, a styrene‐based polymer appended with anthracene groups as reactive side chains was synthesized. First through third‐generation polyester dendrons containing furan‐protected maleimide groups at their focal point were synthesized. Facile, reagent‐free, thermal Diels–Alder cycloaddition between the anthracene‐containing polymer and latent‐reactive dendrons leads to quantitative functionalization of the polymer chains to afford dendronized polymers. The efficiency of this functionalization step was monitored using ¹H and ¹³C NMR spectroscopy and FTIR and UV–vis spectrometry. © 2009 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 48: 410–416, 2010     

Modular synthesis of polymers containing 2,5‐di(thiophenyl)‐N‐arylpyrrole

A modular and facile route has been developed to synthesize functionalized 2,5‐di(thiophen‐2‐yl)‐1‐H‐arylpyrroles from readily available starting materials. These units are compatible with various polymerization conditions and are versatile building blocks for conjugated polymers. The polymers show high thermal stability and solubility in a number of solvents. Characterization of the polymers reveals a correlation between molecular packing, controllable by polymer design, and charge carrier mobility. © 2018 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2018 , 56, 1133–1139     

Improving dispersion and integration of single‐walled carbon nanotubes in epoxy composites by using a reactive noncovalent dispersant

Uniform dispersion and strong interfacial interaction are two critical prerequisites for application of single‐walled carbon nanotubes (SWNTs) in polymer composites. To endow the composites with multifunctional feature, no damage on the chemical/electronic structure of SWNTs is also usually required. With these ends in view, two epoxide‐containing pyrene derivatives (EpPys) were designed, synthesized, and used as reactive noncovalent dispersants for developing multifunctional epoxy/SWNT composites. One having longer chain length between epoxide group and pyrene moiety, that is, EpPy‐16, shows higher dispersing efficiency and provides the nanotube dispersion with better stability, thus picking up for subsequent studies. Systematic characterization on SWNT/EpPy‐16 hybrid demonstrates that 13.2 wt % of EpPy‐16 is adsorbed on the SWNT surface through strong π‐stacking interaction, and intrinsic electronic structure of SWNTs is basically reserved. The solution‐based process adopted here preserves the good SWNT dispersing state in dispersion into the composites. Simultaneously, enhanced interfacial interaction is also realized by using EpPy‐16, which interacts noncovalently with SWNT but connects covalently to epoxy network. As a result, the composites acquire 37 and 22% increments in tensile strength and Young's modulus, respectively, relative to that of neat resin. A low‐electrical percolation threshold of 0.1 wt % SWNTs and improved thermal properties were also observed. © 2012 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2012     

Aligned single‐wall carbon nanotube polymer composites using an electric field

While high shear alignment has been shown to improve the mechanical properties of single‐wall carbon nanotube (SWNT)‐polymer composites, this method does not allow for control over the electrical and dielectric properties of the composite and often results in degradation of these properties. Here, we report a novel method to actively align SWNTs in a polymer matrix, which permits control over the degree of alignment of the SWNTs without the side effects of shear alignment. In this process, SWNTs were aligned via AC field‐induced dipolar interactions among the nanotubes in a liquid matrix followed by immobilization by photopolymerization under continued application of the electric field. Alignment of SWNTs was controlled as a function of magnitude, frequency, and application time of the applied electric field. The degree of SWNT alignment was assessed using optical microscopy and polarized Raman spectroscopy, and the morphology of the aligned nanocomposites was investigated by high‐resolution scanning electron microscopy. The structure of the field induced aligned SWNTs was intrinsically different from that of shear aligned SWNTs. In the present work, SWNTs are not only aligned along the field, but also migrate laterally to form thick, aligned SWNT percolative columns between the electrodes. The actively aligned SWNTs amplify the electrical and dielectric properties of the composite. All of these properties of the aligned nanocomposites exhibited anisotropic characteristics, which were controllable by tuning the applied field parameters. © 2006 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 44: 1751–1762, 2006     

Criss‐cross amphiphilic polymers and analogous model systems

A new class of amphiphilic polymers carrying two pendant docosyl (C22) chains, located at periodic intervals that are separated by PEG chains of varying lengths, was synthesized via a simple melt‐transesterification polymerization, using dimethyl, 2,5‐didocosyloxyterephthalate as one of the monomers. DSC, variable temperature FT‐IR, and WAXS studies demonstrated that immiscibility between the pendant docosyl units and the backbone PEG segments drives their self‐segregation; this results in the crystallization of the pendant docosyl segments and the generation of a lamellar morphology with the alkyl segments and the PEG chains occupying alternate layers. Based on the study of model criss‐cross amphiphiles that resemble the polymer repeat unit, it is postulated that the chains reconfigure such that both the docosyl chains fold to one side of the terephthalate unit while the PEG segments form a loop on the other side; these chains then organize in a bilayer to form the lamellar structure. The simplicity of the synthesis and the rather unique properties of these polymers suggests that such a design could be translated to develop other interesting functional materials that could exploit the immiscibility‐driven microphase separation for the generation of sub‐10 nm domains; these could have potential applications, such as in membranes, solid polymer electrolyte formulations, and so forth. © 2018 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2018 , 56, 1554–1563     

Enhanced dispersion stability of supramolecular complexes of single-walled carbon nanotubes with fluorene-based conjugated polymers

Supramolecular complexes of single-walled carbon nanotubes (SWNTs) with poly(9,9-didodecylfluorene-2,7-diyl) (PF) derivatives were prepared using a solution dispersion process. A series of novel conjugated PF polymers with carboxyl or hydroxyl end groups at both ends were synthesized by the Yamamoto-type coupling of 2,7-dibromo-9,9-didodecylfluorene using Ni(COD)₂ as a catalyst, and further end-capped with either 4-bromobenzoic acid or 4-bromobenzyl alcohol to obtain the end-functionalized PF with different terminal groups. An α-monocarboxy-ω-mono-methoxy poly(ethylene glycol) was connected to both ends of the PF-containing hydroxyl end groups to produce triblock copolymers of poly(ethylene glycol)-b-polyfluorene-b-poly(ethylene glycol) (PEO-b-PF-b-PEO). These SWNTs were completely wrapped with the conjugated polymers through π–π interactions, which enhanced the solubility of the SWNT complexes in organic media, and prevented the aggregation of the polymer–SWNT complexes into large bundles. This indicates that the dispersion stability of SWNTs is enhanced by the addition of the conjugated polymers.     

Side chain length affects backbone dynamics in poly(3‐alkylthiophene)s

Charge transport in conjugated polymers may be governed not only by the static microstructure but also fluctuations of backbone segments. Using molecular dynamics simulations, we predict the role of side chains in the backbone dynamics for regiorandom poly(3‐alkylthiophene‐2,5‐diyl)s (P3ATs). We show that the backbone of poly(3‐dodecylthiophene‐2‐5‐diyl) (P3DDT) moves faster than that of poly(3‐hexylthiophene‐2,5‐diyl) (P3HT) as a result of the faster motion of the longer side chains. To verify our predictions, we investigated the structures and dynamics of regiorandom P3ATs with neutron scattering and solid state NMR. Measurements of spin‐lattice relaxations (T₁) using NMR support our prediction of faster motion for side chain atoms that are farther away from the backbone. Using small‐angle neutron scattering (SANS), we confirmed that regiorandom P3ATs are amorphous at about 300 K, although microphase separation between the side chains and backbones is apparent. Furthermore, quasi‐elastic neutron scattering (QENS) reveals that thiophene backbone motion is enhanced as the side chain length increases from hexyl to dodecyl. The faster motion of longer side chains leads to faster backbone dynamics, which in turn may affect charge transport for conjugated polymers. © 2018 Wiley Periodicals, Inc. J. Polym. Sci., Part B: Polym. Phys. 2018 , 56, 1193–1202     

Novel two‐dimensional donor–acceptor conjugated polymers containing quinoxaline units: Synthesis,characterization, and photovoltaic properties

Novel two‐dimensional donor–acceptor (D–A) structured conjugated polymers, P1–P4, were designed and synthesized by introducing electron‐deficient quinoxaline as core and electron‐rich alkoxyl‐phenylenevinylene in side chains and p‐phenylenevinylene, triphenylamine, or thiophene in main chain. Benefited from the D–A structures, the polymers possess low bandgaps of 1.75 eV, 1.86 eV, 1.59 eV, and 1.58 eV for P1, P2, P3, and P4, respectively, and show broad absorption band in the visible region: the shorter wavelength absorption peak at ～400 nm ascribed to the conjugated side chains and the longer wavelength absorption peak between 500 nm and 750 nm belonging to the absorption of the conjugated main chains. Especially, the absorption band of P4 film covers the whole visible range from 300 nm to 784 nm. The power conversion efficiencies of the polymer solar cells based on P1–P4 as donor and PCBM as acceptor are 0.029%, 0.14%, 0.46%, and 0.57%, respectively, under the illumination of AM 1.5, 100 mW/cm². The polymers with the low bandgap and broad absorption band are promising photovoltaic materials. © 2008 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 46: 4038–4049, 2008     

Direct synthesis of tetrazine functionalities on polymer backbones

Tetrazine mediated inverse Electron Demand Diels–Alder Reaction (IEDDA) is an important modification technique due to its high selectivity and super‐fast kinetics. Incorporation of tetrazine moieties on polymer chains requires multistep synthetic pathways and a post‐polymerization step leading to functional polymeric materials. Such approaches involve separate syntheses of polymer and the molecule which will be employed in modification. Herein, we introduce a straightforward synthetic approach for direct synthesis of tetrazine groups on polymers as side chains. As model systems, tetrazine functional poly(N‐isopropylacrylamide)‐and poly(ethylene glycol)‐based polymers from corresponding precursor polymers with nitrile moieties as pendant groups are prepared and IEDDA Click Reaction is achieved with trans‐cyclooctene derivatives. The click reaction is monitored by both NMR and UV–vis spectroscopies. © 2018 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2019 , 57, 673–680     

Control of SWNT Dispersion by Block Copolymers with a Side‐Chain Polarity Modifier

The dispersion of single‐walled carbon nanotubes (SWNTs) in a non‐polar solvent is controlled with a series of polystyrene‐block‐polybutadiene‐block‐polystyrene (PSBS) block copolymers that contain cholesteryl chloroformate (CC) in side‐chains. Esterification of CC with the partially hydroxylated polybutadiene (PB) blocks allows one to tune the polarity of the block copolymers, which decreases with the amount of CC attached. An excellent dispersion of weak polar SWNTs is observed with PSBS that contains a partially hydroxylated PB block. The dispersion is then significantly deteriorated when the amount of non‐polar CC moieties increases in the block copolymers. A good dispersion is achieved with a polymer that gives rise to strong SWNT–polymer interactions, which ensures contact of the polymer molecules with the nanotube surface, rather than a good solubility of the polymer dispersant in solvent. The stability of the SWNTs in solution arises from unique needle‐like nanowires of the block copolymer aligned perpendicular to the nanotube axis.

     

Naphthodithiophene‐Diketopyrrolopyrrole‐Based donor–Acceptor alternating π‐Conjugated polymers for Organic thin‐Film transistors

Novel naphtho[1,2‐b:5,6‐b′]dithiophene (NDT) and diketopyrrolopyrrole (DPP)‐containing donor‐acceptor conjugated polymers (PNDTDPPs) with different branched side chains were synthesized via Pd(0)‐catalyzed Stille coupling reaction. Octyldodecyl (OD) and dodecylhexadecyl (DH) groups were tethered to the DPP units as the side chains. The soluble fraction of PNDTDPP‐OD polymer in chloroform has much lower molecular weight than that of PNDTDPP‐DH polymer. PNDTDPP‐DH polymer bearing relatively longer DH side chains exhibited much better charge‐transport behavior than PNDTDPP‐OD polymer with shorter OD side chains. The thermally annealed PNDTDPP‐DH polymer thin films exhibited an outstanding charge carrier mobility of ～1.32 cm² V^?1 s^?1 (I_on/I_off ～ 10⁸) measured under ambient conditions, which is almost six times higher than that of thermally annealed PNDTDPP‐OD polymer thin films. © 2013 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2013 , 51, 5280–5290     

Effect of branched alkyl side chains on the performance of thin‐film transistors and photovoltaic cells fabricated with isoindigo‐based conjugated polymers

New isoindigo and di(thienyl)ethylene‐containing π‐extended conjugated polymers with different branched side chains were synthesized to investigate their physical properties and device performance in thin‐film transistors and photovoltaic cells. 11‐Butyltricosane (S3) and 11‐heptyltricosane (S6) groups were used as side‐chain moieties tethered to isoindigo units. The linking groups between the polymer backbone and bifurcation point in the branched side chain differ in the two polymers (i.e., PIDTE‐S3 and PIDTE‐S6 ). The polymers bearing S6 side chains showed much better charge transport behavior than those with S3 side chains. Thermally annealed PIDTE‐S6 film exhibited an outstanding hole mobility of 4.07 cm² V^?1 s^?1 under ambient conditions. Furthermore, bulk heterojunction organic photovoltaic cells made from a blend film of PIDTE‐S3 and (6,6)‐phenyl C61‐butyric acid methyl ester demonstrated promising device performance with a power conversion efficiency in the range of 4.9–5.0%. © 2015 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 2015 , 53, 1226–1234     

Coagulation method for preparing single-walled carbon nanotube/poly(methyl methacrylate) composites and their modulus,electrical conductivity,and thermal stability

A coagulation method providing a better dispersion of single-walled carbon nanotubes (SWNTs) in a polymer matrix was used to produce SWNT/poly(methyl methacrylate) (PMMA) composites. Optical microscopy and scanning electron microscopy showed an improved dispersion of SWNTs in the PMMA matrix, a key factor in composite performance. Aligned and unaligned composites were made with purified SWNTs with different SWNT loadings (0.1–7 wt %). Comprehensive testing showed improved elastic modulus, electrical conductivity, and thermal stability with the addition of SWNTs. The electrical conductivity of a 2 wt % SWNT composite decreased significantly (>10⁵) when the SWNTs were aligned, and this result was examined in terms of percolation. © 2003 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 41: 3333–3338, 2003     

Uni‐molecular nanoparticles of poly(2‐oxazoline) showing tunable thermoresponsive behaviors

Herein, cylindrical molecular bottlebrushes grafted with poly(2‐oxazoline) (POx) as a shaped tunable uni‐molecular nanoparticle were synthesized via the grafting‐onto approach. First, poly(glycidyl methacrylate) (PGMA) backbones with azide pendant units were prepared via reversible addition fragmentation transfer (RAFT) polymerization followed by post‐modification. The degree of polymerization (DP) of the backbones was tuned in a range from 20 to 800. Alkynyl‐terminated POx side chains were synthesized by living cationic ring opening polymerization (LCROP) of 2‐ethyl‐2‐oxazoline (EtOx) and 2‐methyl‐2‐oxazoline (MeOx), respectively. The DP of side chains was varied between 20 and 100. Then, the copper‐catalyzed azide‐alkynyl cycloaddition (CuAAC) click chemistry was conducted with a feed ratio of [alkynyl]:[azide] = 1.2:1 to yield a series of brushes. Depending on the DP of side chains, the grafting density ranged between 47 and 85%. The resulting brushlike nanoparticles exhibited shapes of sphere, rod and worm. Aqueous solutions of PEtOx brushes demonstrated a thermoresponsive behavior as a function of the length of backbones and side chains. Surprisingly, it was found that the lower critical solution temperature of PEtOx brushes increased with a length increase of backbones. © 2017 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2018 , 56, 174–183     

Small molecule self‐assembly in polymer matrices

Using small molecules in polymer matrices is common in applications such as (i) plasticizing polymers to modify the glass transition and mechanical properties and (ii) dispersion of photoactive or electroactive small molecules in polymer matrices in organic‐electronic devices Aggregation of these small molecules and phase separation leading to crystallization often cannot be morphologically controlled. If these are designed with self‐assembling codes such as hydrogen bonding or aromatic interactions, their phase separation behavior would be distinctly different. This review summarizes the studies on morphologies in such situations, such as (i) sub‐surface assembly in polymer matrices, (ii) controlled polymerization‐induced phase separation to create polymer blends, (iii) using the polymer to direct the assembly of small molecules in liquid crystalline devices, (iv) functionalizing a polymer with self‐assembling small molecules to cause organo‐gelation which the polymer itself would not by itself, and (v) using such systems as templates to create porous polymer structures. Organic–inorganic hybrids using polymers as templates for nanostructures and imprinted porous membranes is an emerging area. Since self‐assembly is one of the dominating area of research with respect to both small molecules, polymers as well as the combination of the two, this review summarizes the studies on the aforementioned topics. © 2017 Wiley Periodicals, Inc. J. Polym. Sci., Part B: Polym. Phys. 2018 , 56, 451–478     

Synthesis and photovoltaic properties of copolymers based on benzo[1,2‐b:4,5‐b′]dithiophene and thiophene with electron‐withdrawing side chains

Six alternating conjugated copolymers ( PL1 – PL6 ) of benzo[1,2‐b:4,5‐b′]dithiophene (BDT) and thiophene, containing electron‐withdrawing oxadiazole (OXD), ester, or alkyl as side chains, were synthesized by Stille coupling reaction. The structures of the polymers were confirmed, and their thermal, optical, electrochemical, and photovoltaic properties were investigated. The introduction of conjugated electron‐withdrawing OXD or formate ester side chain benefits to decrease the bandgaps of the polymers and improve the photovoltaic performance due to the low steric hindrance of BDT. Bulk heterojunction polymer solar cells (PSCs) were fabricated based on the blend of the as‐synthesized polymers and the fullerene derivative [6,6]‐phenyl‐C₆₁‐butyric acid methyl ester (PC₆₁BM) in a 1:2 weight ratio. The maximum power conversion efficiency of 2.06% was obtained for PL5 ‐based PSC under the illumination of AM 1.5, 100 mW/cm². © 2011 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2011     

Linking polythiophene chains with vinylene‐bridges: A way to improve charge transport in polymer field‐effect transistors

A series of novel branched polythiophene derivatives bearing different densities of vinylene‐bridges as linking chains were synthesized by a general synthetic strategy. The organic field‐effect transistors, which were fabricated by spin‐coating the polymer solutions onto octadecyltrichlorosilane‐modified SiO₂/Si substrates with top‐contact configuration, afforded a high mobility of 8.0 × 10^?3 cm² V^?1 s^?1 with an on/off ratio greater than 10⁴ and a threshold voltage of about ?3 V in saturation regime. The devices based on these polymers possessed better performance than those of polymers without conjugated bridges and polymers with longer conjugated bridges. These results demonstrated that the combination of conjugated polythiophene backbones and vinylene‐bridges would improve the carrier mobility. As an emerging class of conjugated materials, polymers with vinylene‐bridges as linking chains would open up new opportunities in organic electronics, and their applications in organic electronics are promising. © 2009 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 47: 1381–1392, 2009     

Stimuli‐responsive brush‐shaped conjugated polymers with pendant well‐defined poly(vinyl ether)s

For the synthesis of brush‐shaped conjugated polymers consisting of a poly(phenylene butadiynylene) backbone and well‐defined poly(vinyl ether) (polyVE) side chains, we designed polyVE‐based macromonomers bearing a diethynyl benzene group at the terminus and applied them to the grafting through synthesis. The macromonomer (DE‐PIBVE) was synthesized by living cationic polymerization of isobutyl VE (IBVE) using a functionalized initiator (TMS‐DEVE‐TFA) having a TMS protected diethynyl benzene moiety, followed by deprotection of the TMS groups. As a result, we succeeded in the synthesis of the target brush‐shaped conjugated polymers [poly(DE‐PIBVE)] by oxidative coupling reaction of the diethynyl benzene groups. We found that the solution of poly(DE‐PIBVE) with a specific side chain length exhibited solvatochromism and thermochromism depending on the polarity of the media employed. This phenomenon was attributed to self‐assembly in polar media due to the intermolecular π–π interaction between neighboring conjugated polymer backbones, where the self‐assembly behavior would be closely related to the pendant polyVE structure. © 2016 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2016 , 54, 3318–3325