Agglomeration behavior of lipid-capped gold nanoparticles

The current investigation deciphers aggregation pattern of gold nanoparticles (AuNPs) and lipid-treated AuNPs when subjected to aqueous sodium chloride solution with increasing ionic strengths (100–400 nM). AuNPs were synthesized using 0.29 mM chloroauric acid and by varying the concentrations of trisodium citrate (AuNP1 1.55 mM, AuNP2 3.1 mM) and silver nitrate (AuNP3 5.3 μM, AuNP4 10.6 μM) with characteristic LSPR peaks in the range of 525–533 nm. TEM analysis revealed AuNPs to be predominantly faceted nanocrystals with the average size of AuNP1 to be 35?±?5 nm, AuNP2 15?±?5 nm, AuNP3 30?±?5 nm, and AuNP4 30?±?5 nm and the zeta-average for AuNPs were calculated to be 31.23, 63.80, 26.08, and 28 nm respectively. Induced aggregation was observed within 10 s in all synthesized AuNPs while lipid-treated AuNP2 (AuNP2-L) was found to withstand ionic interferences at all concentration levels. However, lipid-treated AuNPs synthesized using silver nitrate and 1.55 mM trisodium citrate (AuNP3, AuNP4) showed much lower stability. The zeta potential values of lipid-treated AuNPs (AuNP1-L-1x/200, ??17.93?±?1.02 mV; AuNP2-L-1x/200, ??21.63?±?0.70; AuNP3-L-1x/200, ??14.54?±?0.90; AuNP3-L-1x/200 ??13.77?±?0.83) justified these observations. To summarize, AuNP1 and AuNP2 treated with lipid mixture 1 equals or above 1x/200 or 1x/1000 respectively showed strong resistance against ionic interferences (up to 400 mM NaCl). Use of lipid mixture 1 for obtaining highly stable AuNPs also provided functional arms of various lengths which can be used for covalent coupling.

Open image in new window

Graphical abstract Agglomeration behavior of gold nanoparticles before and after lipid capping

     

One step alkaline synthesis of biocompatible gold nanoparticles using dextrin as capping agent

Gold nanoparticles (AuNPs) are used in sensing methods as tracers and transducers. The most common AuNP synthesis techniques utilize citrate under acidic reaction conditions. The synthesis described in this article generates glyco-AuNPs under mild alkaline conditions providing a “greener” alternative to Brust and Turkevich methodologies. This biologically compatible one-step technique uses dextrin as a capping agent and sodium carbonate as the reducing agent for chloroauric acid. The generated particles were relatively mono-dispersed and water soluble with a range of controllable mean diameters from 5.9 to 16.8 ± 1.6 nm. The produced AuNPs were stable in water for more than 6 months stored at room temperature (21 °C) in generation solution without protection from light. This article shows the effect of temperature, pH, and dextrin concentration on the synthesis procedure and AuNP diameter. These factors were found to control the reaction speed. The produced glyco-AuNPs were successfully functionalized with DNA oligonucleotides, and the functionalization efficiency was similar to citrate-generated AuNPs. The alkaline synthesis allows future exploration of simultaneous synthesis and functionalization procedures, which could significantly reduce the time of current ligand exchange methodologies.     

Negative‐Imaging of Citrate Layers on Gold Nanoparticles by Ligand‐Templated Metal Deposition: Revealing Surface Heterogeneity

Surface heterogeneity of a metal nanoparticle is typically regarded as boundary defects and various crystalline facets. While organic capping ligands of a single type are assumed to be homogeneously distributed on the nanoparticle surface, heterogeneous surface coverage of citrate molecules on individual facets of gold nanoparticles (AuNPs) is revealed. Pt metallic clusters with 2 nm in diameter, epitaxially grown on the surface of AuNPs by chemical reaction and imaged by high‐resolution transmission electron microscopy, are utilized as negative‐imaging probes for densely packed adlayers where the underneath gold surface may not be accessible for Pt deposition. At pH > 5.0, citrate anions form only a loosely packed layer. At pH 4.5, citrates and citric acids form both loosely packed and densely packed layers that appear phase separated, and the densely packed domain as small as 5 nm × 5 nm is likely composed of fully protonated citric acids. IR spectra indicate that citric acid binds to a surface Au adatom through the oxygen atom of the central hydroxyl group, and similarly, citrate anions bind to Au adatoms through the carboxylate oxygen atom. This study also reveals the role of Au adatom in the adsorption of citrate species on the metallic surface of AuNPs.     

ICP-MS: a powerful technique for quantitative determination of gold nanoparticles without previous dissolving

A direct and simple inductively coupled plasma mass spectroscopy (ICP-MS) method for the determination of gold nanoparticles (AuNP) with different particle sizes ranging from 5 to 20 nm and suspended in aqueous solutions is described. The results show no significant difference compared to the determination of the same AuNPs after digestion, as claimed by the literature. The obtained limit of quantification of the method is 0.15 μg/L Au(III) that corresponds to 4.40 × 10⁹ AuNP/L, considering spherical AuNPs 15 nm sized. Spike recovery experiments have shown that the sample matrix is a significant factor influencing the accuracy of the measurement. Spike recoveries from 93% to 95% are found for AuNP samples prepared in trisodium citrate, while for deionized H₂O a spike recovery of around 80% was obtained. The sample preparation mode along with the ICP-MS parameters have been optimized and found to be crucial so as to achieve the required accuracy for the direct quantification of AuNP suspensions. The effect of the nanoparticle size upon the ICP-MS signal also was studied, and only significant differences due to the chemical environment and not to the AuNPs size were found.     

Temperature–Light Dual‐Responsive Au@PNIPAm Core‐Shell Microgel‐Based Optical Devices

Au nanoparticle (AuNP) core particles coated with a poly(N‐isopropylacrylamide) (pNIPAm) shell (Au@pNIPAm) are synthesized by seed mediated free radical polymerization. Subsequently, a temperature–light‐responsive photonic device is fabricated by sandwiching the Au@pNIPAm particles between two thin layers of Au. The optical device exhibits visual color and characteristic multipeak reflectance spectra, where peak position is primarily determined by the distance between two Au layers. Dual responsivities of the photonic device are achieved by combining the photothermal effect of AuNPs core (localized surface plasmon resonance (LSPR) effect) and the temperature responsivity of the pNIPAm shell. That is, the pNIPAm shell collapses as the temperature is increased above pNIPAm's lower critical solution temperature, either by direct heat input or heat generated by AuNPs' LSPR effect. To investigate the effect of AuNPs distribution in the microgels on the devices' photothermal responsivity, the Au@pNIPAm microgel‐based etalon devices are compared with that fabricated by AuNP‐doped pNIPAm‐based microgels; in terms of response kinetics and optical spectrum homogeneity. The uniform Au@pNIPAm microgel‐based devices show a fast response and exhibit a comparatively homogeneous spectrum over the whole slide. These materials can potentially find use in drug delivery systems, active optics, and soft robotics.     

Surface property modification of well-dispersed amphiphilic gold nanoparticles as individuals

Amphiphilic gold nanoparticles (AuNPs) functionalized with mixed monolayers consisting of hydrophobic and hydrophilic ligands find widespread applications in biosensing, drug delivery, and bioimaging. One important aspect of amphiphilic AuNPs in such applications is the tuning of the surface properties of these AuNPs by modifying the composition of the ligands. In this study, well-dispersed AuNPs as individuals with mixed monolayers of hydrophobic and hydrophilic ligands were synthesized and the ratios of hydrophilic and hydrophobic ligands on the AuNP surfaces with varying ligand lengths were investigated by electrostatic titration. We demonstrated that longer hydrophobic ligands have higher affinity for the AuNP surface, and that the relative ligand length plays an important role in determining the maximum hydrophobic coverage on the AuNP surface at which the ratio of the amount of hydrophobic to that of hydrophilic ligands on the AuNP surface is the largest, for AuNPs to remain as individuals. We expect that the AuNPs synthesized with diverse ratios of hydrophobic and hydrophilic ligands on the surface can be useful in biological applications.

Open image in new window

Graphical abstract ?

     

Formation and encapsulation of gold nanoparticles using a polymeric amine reducing agent

We report on the use of poly(allylamine) hydrochloride (PAH) as a reducing agent for the controlled formation of gold nanoparticles (AuNPs) in the size range of 5–50 nm. The formation of AuNPs using this polymer matrix allows for the AuNPs to be imbedded in the polymer matrix, once formed. The kinetics of AuNP formation are shown to be pseudo first-order in [HAuCl₄] at room temperature. The kinetics of AuNP formation are controlled by the ratio of reducing agent to HAuCl₄ as well as the overall concentration of the PAH and HAuCl₄. Additionally, at low PAH:HAuCl₄ mole ratios, the plasmon resonance wavelength can be controlled through the ratio of the reactants. This plamson resonance shift is shown to be related to AuNP size by means of TEM imaging data on the AuNPs.     

Ferritin as a photocatalyst and scaffold for gold nanoparticle synthesis

The ferrihydrite mineral core of ferritin is a semi-conductor capable of catalyzing oxidation/reduction reactions. This report shows that ferritin can photoreduce AuCl₄ ⁻ to form gold nanoparticles (AuNPs). An important goal was to identify innocent reaction conditions that prevented formation of AuNPs unless the sample was illuminated in the presence of ferritin. TRIS buffer satisfied this requirement and produced AuNPs with spherical morphology with diameters of 5.7 ± 1.6 nm and a surface plasmon resonance (SPR) peak at 530 nm. Size-exclusion chromatography of the AuNP–ferritin reaction mixture produced two fractions containing both ferritin and AuNPs. TEM analysis of the fraction close to where native ferritin normally elutes showed that AuNPs form inside ferritin. The other peak eluted at a volume indicating a particle size much larger than ferritin. TEM analysis revealed AuNPs adjacent to ferritin molecules suggesting that a dimeric ferritin–AuNP species forms. We propose that the ferritin protein shell acts as a nucleation site for AuNP formation leading to the AuNP-ferritin dimeric species. Ferrihydrite nanoparticles (~10 nm diameter) were unable to produce soluble AuNPs under identical conditions unless apo ferritin was present indicating that the ferritin protein shell was essential for stabilizing AuNPs in aqueous solution.     

Biological Production of Gold Nanoparticles at Different Temperatures: Efficiency Assessment

The study aims to compare different approaches and efficacies during the biological production of nanoparticles (NPs). Gold nanoparticles (AuNPs) are produced by Fusarium oxysporum at two different temperatures. One flask is incubated at 37 °C (“Common”) and the other is directly heated for 5 min at 80 °C (“Heat-treated”). Obtained AuNPs are analyzed and compared by spectrophotometry, transmission electron microscopy (TEM), scanning electron microscopy (SEM), energy dispersive X-ray spectroscopy (EDS), dynamic light scattering (DLS), and Fourier transform infrared spectroscopy (FTIR). Graphite furnace atomic absorption spectroscopy (GF-AAS) is used to determine the particle concentration after the AuNPs production. The AuNPs prepared by both (the Common and the Heat-treated) methods exhibit maximum absorption peaks at 541 and 528 nm, respectively, and have round shapes and sizes of less than 50 nm. Their zeta potential is about −28 mV. GF-AAS shows that the efficiency of AuNP production in Common- and Heat-treated samples is equal, between 65% and 68%. Since the Heat-treated sample shows a better size distribution, the use of higher temperature and shorter time period is preferable for the bioproduction of AuNPs. It seems that shortening the time for the production of AuNPs prevents the formation of larger NPs.     

Copolymer Particles with Incorporated Gold and Silver Nanoparticles to Absorb Short‐Wavelength Scattering in Full‐Color Photonic Glasses

Photonic glasses (PGs) have fascinated researchers because the structural colors that are reflected from PGs are angle independent. However, low color saturation, especially for colors at longer wavelengths, is an obstacle for realizing full‐color PGs. It is reported that the form‐factor‐(FF)‐derived reflections that degrade the color saturation of PGs can be removed by embedding Ag and Au nanoparticles (NPs) into copolymers. Styrene and 4‐vinylpyridne copolymer particles are prepared and used as nanotemplates to synthesize AgNPs and AuNPs. The wavelength of the FF‐derived reflections in relation to the diameter of the particles is estimated. NPs with an absorption spectrum corresponding to the calculated values are then selectively embedded in the copolymer particles. PGs fabricated with AgNP‐ and AuNP‐embedded copolymer particles exhibit fewer FF‐derived reflections owing to the surface‐plasmon‐resonance‐induced absorption of the embedded NPs. Using these FF‐reduced PGs, angle‐independent full‐color PG pigments are realized.     

Efficient and Rapid Synthesis of Radioactive Gold Nanoparticles by Dielectric Barrier Discharge

A compact bench‐top system based on a dielectric barrier plasma discharge (DBD), enables the rapid, automatable, and continuous‐flow synthesis of gold nanoparticles (AuNPs) and radioactive gold nanoparticles (¹⁹⁸AuNPs). AuNPs are used as radiosensitizers in oncology, and ¹⁹⁸AuNPs (half‐life: 2.7 d) have been suggested as potential cancer brachytherapy sources. Plasma applied at the surface of a liquid containing gold ions (AuCl₄^?) and dextran induces the production of AuNPs directly in water. This synthesis is monitored in real time by UV–visible spectrometry: the change of absorbance of the solution provides new insights on the growth dynamics of AuNPs by plasma synthesis. By balancing gold ions and surfactant molecules, particles with a diameter lying in the optimal range for radiosensitizing applications (28 ± 9 nm) are produced. The method yields a reduction of more than 99% of the gold ions within only 30 min of plasma treatment. A postsynthesis ripening of the AuNPs is revealed, monitored by UV–visible spectrometry, and quantified within the first few hours following plasma treatment. Radioactive ¹⁹⁸AuNPs are also produced by DBD synthesis and characterized by electron microscopy and single‐photon emission computed tomography imaging. The results confirm the efficiency of DBD reactors for AuNPs synthesis in oncology applications.     

Steric hindrance in cationic and neutral rhodamine 6 G molecules adsorbed on Au nanoparticles

The adsorption of cationic and neutral R6G molecules on Au nanoparticles was elucidated by surface enhanced Raman scattering (SERS). The steric hindrance at hydroethyl amino (‐N(H)Et) groups in R6G was evidenced by the observation that R6G⁺ adsorb on as‐prepared gold nanoparticles (AuNPs) only with electrostatic forces, in contrast to the electrostatic and chemical adsorption of R123⁺ with dihydro amino (‐NH₂) groups on as‐prepared AuNPs. Large steric hindrance at the amino groups in R6G yielded saturated coverage of 700 molecules/AuNP for R6G⁺ significantly fewer than 1000 molecules/AuNP for R123⁺. In addition, neutral R6G⁰ on AuNPs showed markedly enhanced peaks at 1200–1600 cm⁻¹, which were not observed in Raman spectra of R6G⁰ in bulk solution, and also in SERS of R6G⁺ on AuNPs. These bands are attributed to vibrational modes of an outer phenyl ring and ethyl amino groups, which are vertical to a xanthene plane, on the basis of theoretical analysis of molecular vibrations. Thus, Raman scattering of these bands is enhanced under an inclined orientation of R6G⁰ molecules chemisorbed on AuNPs via lone pair electrons at amino groups. Copyright © 2013 John Wiley & Sons, Ltd.     

Portable smart films for ultrasensitive detection and chemical analysis using SERS and SERRS

Metallic nanostructures, much smaller than the wavelength of visible light, which support localized surface plasmon resonances, are central to the giant signal enhancement achieved in surface‐enhanced Raman scattering (SERS) and surface‐enhanced resonance Raman scattering (SERRS). Plasmonic driven SERS and SERRS is a powerful analytical tool for ultrasensitive detection down to single molecule detection. For all practical SERS applications a key issue is the development of reproducible and portable SERS‐active substrates, where the most widely used metals for nanostructure fabrication are silver and gold. Here, we report the fabrication of a ‘smart film’, containing gold nanoparticles (AuNPs), produced by in situ reduction of gold chloride III (Au⁺³) in natural rubber (NR) membranes for SERS and SERRS applications. The composite films (NR/AuNP membranes) show characteristic plasmon absorption of Au nanostructures, which notably do not influence the mechanical properties of the NR membranes. The term ‘smart film’ has to do with the fact that the SERS substrate (smart film) is flexible and standalone, which allows one to take it anywhere and to dip it into solutions containing the analyte to be characterized by SERS or SERRS technique. Besides, the synthesis of the AuNPs at the surface of NR films is much simpler than making an Au colloid and cast it onto a substrate surface or preparing an Au evaporated film. Copyright © 2012 John Wiley & Sons, Ltd.     

Design of Gold Nanoparticles in Dendritic Cell‐Based Vaccines

The design of effective cancer vaccines must be able to activate dendritic cells (DCs) of the innate immune system in order to induce immunity to pathogens and cancer. DCs patrol the body and once they encounter antigens, they orchestrate a complex mechanism of events and signals that can alert the adaptive immune system to action. However, DC‐based vaccines remain a challenge in part because the source and quality of antigens, the DC targeting molecule, type of adjuvant, and delivery vehicle must be optimized to induce a robust immune response. Gold nanoparticles (AuNPs) have now entered clinical trials as carriers due to their ease of functionalization with antigens, adjuvants, and targeting molecules. This progress report discusses how AuNPs can influence DC activation and maturation, as well as their potential impact on T helper (Th) differentiation. Ultimately, successful AuNP‐based DC vaccines are able to induce phagocytosis, activation/maturation, migration, T cell costimulation, and cytokine secretion, which is named AuNP‐induced DC tuning (AuNP‐DC tuning). Although at its infancy, understanding the processes of AuNP‐DC tuning will give a better understanding of how best to engineer AuNPs and will redefine the next generation of DC‐based vaccines.     

Raman spectroscopy of combinatory anticancer drug release from gold nanoparticles inside a single leukemia cell

Combinatory anticancer drug release from gold nanoparticles (AuNPs) in K562 human myeloid leukemia cells was performed using Raman spectroscopy. We fabricated the anticancer drug of imatinib as a BCR‐ABL tyrosine kinase inhibitor on AuNP surfaces along with a transferrin (Tf)‐targeting moiety to treat the leukemia cells. DNA topoisomerase I inhibitor topotecan was also assembled to monitor its fluorescence onto AuNPs. The linker group of 4‐carboxylic benzoic acid was used to conjugate to targeting the Tf protein. Our Raman data indicated that the drug molecules were not detached in the cell culture media but released after treatment with glutathione (2 mM). Intracellular distribution and release of the anticancer drug–AuNP conjugates in K562 cells were examined by both fluorescence microscopy and dark‐field microscopy with surface‐enhanced Raman scattering. Copyright © 2013 John Wiley & Sons, Ltd.     

The design of a peptide linker group to enhance the SERS signal intensity of an atto680 dye‐nanoparticle system

The Surface enhanced resonance Raman spectroscopy (SERRS) spectra of three modified atto680 dyes were recorded using Au nanoparticles and an excitation laser operating at 670 nm. The dyes were modified with linker groups based on the small peptides, Cys, Cys–Gly and Cys–Gly–Gly. The Cys thiol group acted as the coupling point to the Au surface and the Gly  NH₂ group used to attach the dye. The maximum signal was recorded for the Cys–Gly linker. This gave a signal intensity for the 577 cm⁻¹ Raman peak of the atto680 dye that was more than 27 times greater than the unmodified dye. The Au nanoparticles used had a diameter of 49.8 ± 1.2 nm and were synthesised by the citrate reduction method. The Raman dye‐AuNP probes were also used in an immunoassay to detect mouse IgG in the femto mole range. Copyright © 2010 John Wiley & Sons, Ltd.     

Structure and Stability of PEG‐ and Mixed PEG‐Layer‐Coated Nanoparticles at High Particle Concentrations Studied In Situ by Small‐Angle X‐Ray Scattering

Ligand‐layer structure and stability of gold nanoparticles (AuNP) coated with α‐methoxypoly(ethylene glycol)‐ω‐(11‐mercaptoundecanoate) (PEGMUA) layers and mixed layers of PEGMUA and 11‐mercaptoundecanoic acid (MUA) at high AuNP concentrations are studied in situ by small‐angle X‐ray scattering (SAXS). The thickness of the ligand layer is modified by the molecular weight of the PEG‐ligands (2 and 5 kDa), and the PEG‐grafting density is decreased by coadsorption of MUA. The response of the conjugates to a pressure of up to 4 kbar is probed. The results indicate strongly hydrated PEG layers at high grafting densities. The stability of the mixed ligand‐layer conjugates is lower. This is most probably due to enhanced interparticle PEG–PEG interactions at lower grafting densities. The presented study demonstrates that a detailed structural characterization of polymer ligand layers in situ and in response to external stimuli is possible with SAXS.     

Direct Synthesis of Gold Nanoparticle‐Over‐Nanosheet for Sensitive SERS Detection

A simple ethanol sol‐based method for the synthesis of gold nanosheets (AuNSs) and gold nanoparticle‐over‐nanosheet (AuNP/NS) is developed. Gold nanoparticles (AuNPs) with average sizes of ≈8 nm are grown in situ on the surface of the AuNS, which forms a NP/NS structure that obtains strong, significantly improved, surface‐enhanced Raman spectroscopy activity with the magnitude ≈2 and ≈6 orders higher than the simplex AuNP and AuNS, respectively. This performance is mainly attributed to uniform AuNPs that are closely packed over AuNS and coupled with NP–NS and NP–NP interactions. The NP–NS–GP (the gap between NP–NS) is narrower than NP–NP–GP in which much stronger and steadier plasmon resonance is obtained that can significantly enhance the Raman signal. The results show that single‐crystalline AuNS is an ideal substrate, which can be further coated with other metallic NPs to form a new flexible, high‐activity and AuNS‐based nanocomposite for a wide variety of applications.     

Highly sensitive colorimetric and fluorescent sensor for cyanazine based on the inner filter effect of gold nanoparticles

Cyanazine residue poses a great threat to human health and its derivatives would remain in soils, natural waters, and other environmental domains for a long time. Herein, a simple, rapid, and ultra-sensitive analytical method for the determination of cyanazine (CZ) based on inner filter effect (IFE) of Au nanoparticles (AuNPs) on the fluorescence of CdTe quantum dots (QDs) is first described in this study. With the presence of citrate-stabilized AuNPs, the fluorescence of GSH-capped CdTe QDs was remarkably quenched by AuNPs via IFE. The fluorescence of the AuNP–CdTe QD system was recovered upon addition of CZ. CZ can adsorb on to the surface of AuNPs due to its cyano group that has good affinity with gold, which could induce the aggregation of AuNPs accompanying color change from red to blue. Thus, the IFE of AuNPs on CdTe QDs was weakened, and the fluorescence intensity of CdTe QDs was recovered accordingly. A good linear correlation for detection of CZ was exhibited from 0.05 to 9 μM, and the detection limit reached 0.1568 μM, which was much lower than the safety limit required by the USA, the UK, and China. In order to probe into the selectivity of AuNPs towards CZ over other pesticides, various frequently used pesticides were mixed with AuNPs. AuNP composite solution shows good selectivity towards CZ among other pesticides. This method was successfully carried out for the assessment of CZ in real samples with satisfactory results, which revealed many advantages such as high sensitivity, low cost, and non-time-consuming compared with traditional methods.     

Photocatalytic synthesis of intensely photoluminescent gold nanoclusters and application in cell imaging

In this article, a facile and rapid method was developed to synthesize intensely photoluminescent gold nanoclusters (AuNCs) based on photocatalytic reduction. Using (5-mercapto-1,3,4-thiadiazol-2-ylthio)acetic acid (TMT) that is a photosensitive material as the ligands, AuNC@TMT, with high photoluminescence quantum yield (19.7%), were prepared. The average diameter of gold core is 1.69 ± 0.22 nm. The maximum excitation and emission wavelengths of AuNC@TMT are at 422 and 516 nm, respectively. The mechanism of photocatalytic reduction is preliminarily understood. Under UV lamp with 365 nm irradiation, Au(Ι)-TMT complex occurred with electron transfer from TMT to Au(Ι), which was reduced to Au(0) as the gold core of AuNC. Thus, it indicates that the photosensitive and electron transport materials with a thiol group will be superior ligands for synthesis of intensely photoluminescent AuNCs.