Preparation and properties of new polyimides derived from 1,6-diaminodiamantane

New polyimides containing diamantane units were prepared by a conventional two-step method starting from 1,6-diaminodiamantane and aromatic dianhydrides. The intermediate poly(amic acid)s had inherent viscosities of 0.33–0.55 dL/g. These polyimides did not decompose below 400°C in air or nitrogen atmosphere, and the temperature at 5% weight loss were above 491°C. The glass transition temperatures of the polyimides were found to be 375–429°C by DSC. These polyimides had almost the same semicrystalline patterns and exhibited crystalline diffraction peak (2 θ) at around 15°. The polyimide Vb exhibited a melting endothermic peak at 514°C. © 1996 John Wiley & Sons, Inc.     

Structure‐property relationships for a series of amorphous partially aliphatic polyimides

High molecular weight, soluble, amorphous, partially aliphatic polyimides were successfully synthesized using an ester acid high‐temperature solution imidization route, which allows one to control desired glass‐transition (T_g) and processing temperatures. This method involves the prereaction of aromatic dianhydrides with ethanol and a tertiary amine catalyst to form ester acids, followed by the addition of diamines. Subsequent thermal reaction forms fully cyclized polyimides. This reaction pathway eliminates the need for anhydrous solvents and overcomes the problem of salt formation commonly observed for nucleophilic, more‐basic aliphatic amines when utilizing the traditional polyamic acid synthesis route. The molar ratio of aromatic‐to‐aliphatic diamines was varied to generate a series of copolyimides with the chosen dianhydride and tailor the physical properties for specific adhesive applications. This series of copolyimides was characterized by their molecular weight, T_g, thermal stability, coefficient of thermal expansion, refractive index, and dielectric constant. Structure‐property relationships were established. The γ and β sub‐T_g viscoelastic properties were researched to understand their molecular origins. © 2002 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 40: 1503–1512, 2002     

Synthesis and properties of novel polyimides from sulfonated binaphthalene dianhydride for proton exchange membranes

A sulfonated dianhydride monomer, 6,6′‐disulfonic‐4,4′‐binaphthyl‐1,1′,8,8′‐tetracarboxylic dianhydride (SBTDA), was successfully synthesized by direct sulfonation of the parent dianhydride, 4,4′‐binaphthyl‐1,1′,8,8′‐tetracarboxylic dianhydride (BTDA), using fuming sulfuric acid as the sulfonating reagent. A series of sulfonated homopolyimides were prepared from SBTDA and various common nonsulfonated diamines. The resulting polymer electrolytes, which contain ion conductivity sites on the deactivated positions of the aryl backbone rings, displayed high proton conductivities of 0.25–0.31 S cm^?1 at 80 °C. The oxidative stability test indicated that the attachment of the ? SO₃H groups onto the dianhydride units did not deteriorate the oxidative stability of the SPI membranes. The better membranes were achieved by the copolymerization of nonsulfonated diamine, SBTDA, and BTDA. Copolymer membrane synthesized from hexane‐1,6‐diamine, SBTDA, and BTDA displayed excellent water stability of more than 1000 h at 90 °C, while its proton conductivity was still at a high level (comparable to that of Nafion 117). Furthermore, the novel block copolymer ( II‐b ) displayed higher proton conductivity compared with the random one ( II‐r ) obviously, probably due to the slightly higher water uptake and better microphase separated morphology. © 2008 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 46: 2820–2832, 2008     

Physicochemical and thermal effects of pendant groups,spatial linkages and bridging groups on the formation and processing of polyimides

Aromatic polyimides are known for their remarkable thermal and chemical properties which are greatly influenced by their precursors. In this study, we report synthesis and characterization of four different aromatic polyimides. The four different dianhydrides (ODPA, BTDA, BPDA, and PMDA) were reacted with a diamine (BisAPAF) via azeotropic imidization under same conditions. FTIR analysis confirmed the formation of aromatic polyimides and all but one polyimide (HPI-BPDA) were found to be completely soluble in common solvents. The obtained molecular weights were between 16,000 and 32,000?g/mol, glass transition temperatures were between 250?°C and 275?°C, degradation temperatures were above 550?°C, and the d-spacing values were around 5?Å. These properties are promising and can be beneficial for various applications such as thin films and membranes.     

Synthesis and characterization of fully aliphatic polyimides from an aliphatic dianhydride with piperazine spacer for enhanced solubility,transparency, and low dielectric constant

A new series of fully aliphatic polyimide (API) based on a novel aliphatic dianhydride monomer‐2,2′‐(1,4‐piperazinediyl)‐disuccinic anhydride (PDA), in which two units of succinic anhydride have been connected by an aliphatic heterocyclic piperazine spacer that possesses aminomethylene (‐NCH₂) moiety in the aliphatic/alicylic backbone capable of inducing charge transfer (CT) interactions in the polyimide network, was successfully synthesized. The APIs were soluble in common polar organic solvents. The polyimide films of PDA with alicyclic diamines were almost colorless. T₁₀ (temperature of 10% weight loss) of APIs were ranged from 299–418 °C and T_g of API3‐API6 were in the temperature range of 170 to 237 °C. The light‐colored polyimide films of API3‐API6 possessed good mechanical properties with tensile strength of 54–72 Mpa, tensile modulus of 1.6–2.3 Gpa and elongation at break of 4–9%. The polyimide films of API3‐API6 were highly flexible and free‐standing which is quite rare in fully APIs. The dielectric constant of one of the synthesized API (API4) was as low as 2.14. © 2014 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2014 , 52, 2316–2328     

High Tg and high organosolubility of novel unsymmetric polyimides

A series of new polyimides (PIs) containing di‐tert‐butyl side groups were synthesized via a polycondensation of 1‐(4‐aminophenoxy)‐4‐(4‐amino‐2‐methylphenyl)‐2,6‐di‐tert‐butylbenzene ( 3 ) with various aromatic tetracarboxylic dianhydrides. The novel unsymmetric PIs exhibited a low dielectric constants (2.78–3.02), low moisture absorption (0.53–1.35%), excellent solubility, and high glass transition temperature (308–450 °C). The PI derived from the new diamine and the very rigid naphthalene‐1,4,5,8‐tetracarboxylic dianhydride (NTDA) was soluble in N‐methyl‐2‐pyrrolidone, chloroform, m‐cresol, and cyclohexanone. The unsymmetric di‐tert‐butyl pendent groups significantly enhance the rotational barrier of the polymer chains; thus these PIs had high T_gs. The ¹H NMR spectrum of the diamine 3 revealed that the protons of 4‐aminophenoxy moiety are not chemical shift equivalent. This is because the steric hindrance of the bulky di‐tert‐butyl groups prevents the benzene ring of 4‐aminophenoxy moiety from rotating freely. © 2009 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 47: 2443–2452, 2009     

Crystallization and glass properties of pentitols

Thermodynamic and dynamic data of the four pentitols, xylitol, adonitol, l-arabitol and d-arabitol, measured by temperature modulated DSC (TMDSC) in the crystalline and amorphous states are presented. The properties of the supercooled liquids clearly show two distinct kinds of thermal behaviors with regard to their aptitude to crystallize. The capacity of the TMDSC technique to characterize both the molecular mobility and the thermal behavior is used to analyze the stability of the supercooled liquid state of the compounds. The comparison between the pentitols shows that the crystallization processes are mainly dominated by the interfacial energy rather than by a competition between the thermodynamic driving force and the molecular mobility. This revised version was published online in July 2006 with corrections to the Cover Date.     

Preparation and properties of imide‐containing elastic polymers from elastic polyureas and pyromellitic dianhydride

A new approach to obtain imide‐containing elastic polymers (IEPs) via elastic and high‐molecular‐weight polyureas, which were prepared from α‐(4‐aminobenzoyl)‐ω‐[(4‐aminobenzoyl)oxy]‐poly(oxytetramethylene) and the conventional diisocyanates such as tolylene‐2,4‐diisocyanate(2,4‐TDI), tolylene‐2,6‐diisocyanate(2,6‐TDI), and 4,4′‐diphenylmethanediisocyanate (MDI), was investigated. IEP solutions were prepared in high yield by the reaction of the polyureas with pyromellitic dianhydride in N‐methyl‐2‐pyrrolidone (NMP) at 165°C for 3.7–5.2 h. IEPs were obtained by the thermal treatment at 200°C for 4 h in vacuo after NMP was evaporated from the resulting IEP solutions. We assumed a mechanism of the reaction via N‐acylurea from the identification of imide linkage and amid acid group in IEP solutions. NMR and FTIR analyses confirmed that IEPs were segmented polymers composed of imide hard segment and poly(tetramethylene oxide) (PTMO) soft segment. The dynamic mechanical and thermal analyses indicated that the IEPs prepared from 2,6‐TDI and MDI showed a glass‐transition temperature (T_g ) at about −60°C, corresponding to T_g of PTMO segment, and suggested that microphase‐separation between the imide segment and the PTMO segment occured in them. TGA studies indicated the 10% weight‐loss temperatures (T₁₀) under air for IEPs were in the temperature range of 343–374°C. IEPs prepared from 2,6‐TDI and MDI showed excellent tensile properties and good solvent resistance. © 2000 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 38: 715–723, 2000     

Synthesis and properties of polyimides from 4,4′-binaphthyl-1,1′,8,8′-tetracarboxylic dianhydride

4,4′-Binaphthyl-1,1′,8,8′-tetracarboxylic dianhydride was synthesized from 4-chloro-1,8-naphthalic anhydride and polymerized with aromatic and pliphatic diamines in m-cresol or N-methyl-2-pyrrolidinone (NMP). The polyimides, except for two derived from p-phenylenediamine and hydrazine, are soluble in 1,1,2,2-tetrachloroethane and NMP. Their intrinsic viscosities ranged from 0.36 to 2.20 dL/g. The polymers showed excellent thermal and thermooxidative stabilities and displayed weak glass transition temperatures. Young's moduli of some polymer films were in the range of 2.5 and 5.4 GPa at 30°C. The aliphatic polyimides exhibited a stronger fluorescence than the aromatic polyimides. © 1995 John Wiley & Sons, Inc.     

Constitutionally isomeric alicyclic polyimides: Origin of siteselectivity in the reaction of unsymmetrical dianhydride and structure‐derived difference in physical properties

Two constitutionally isomeric alicyclic polyimides (PIs), head‐to‐head (HH) and random types, were successfully synthesized on the basis of a siteselective ring opening reaction of an unsymmetric spiroalicyclic dianhydride, rel‐[1R,5S,6R]‐3‐oxabicyclo[3,2,1]octane‐2,4‐dione‐6‐spiro‐3′‐(tetrahydrofuran‐2′,5′‐dione), with using several kinds of diamines only by changing reaction procedures. A model reaction study revealed that the origin of the siteselectivity in the reaction of the dianhydride was due to both the enhanced reactivity of six‐membered anhydride embedded in bicyclo[3.2.1] system and the reduced reactivity of five‐membered anhydride in the spiro[4.5] system. The HH‐PIs showed higher glass transition temperature and higher dielectric constant than those of random PIs. Specific gravity of the PI films showed that the differences in physical properties stem from different packing density of the two constitutionally isomeric PIs. This is the first example for constitutionally isomeric both amorphous polycondensates with different physical properties. © 2012 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2012     

Influence of the polymer structure on the achievement of polar orientation in high glass transition temperature nonlinear optical polyimides by photo-assisted poling

We have used combinations of light, heat, and electrostatic fields to investigate the orientation of nonlinear azo-chromophores chemically incorporated into high glass transition temperature (T_g) polyimides. A number of nonlinear optical polyimides have been synthesized in which the interaction between the nonlinear optical chromophore and the polymer main chain was systematically altered to determine to what extent this steric interaction influences the orientation of the nonlinear chromophore. Chromophores in polymers may be oriented by a number of methods: (a) polarized light at room temperature (i.e., photo-induced orientation or PIO), (b) polarized light and electric fields (i.e., photo-assisted poling or PAP) at temperatures ranging from room temperature to the polymer T_g, and (c) electric fields at T_g (thermal poling). While thermal poling and PIO are usually possible, PAP depends strongly on the molecular structure of the polymer. Previously we have shown that PIO can be accomplished at room temperature in a system where the nonlinear chromophore is embedded into the polyimide main chain via the donor substituent, and this orientation can only be thermally erased at temperatures approaching T_g. In this article we show that, whereas photoisomerization can efficiently depole donor-embedded polyimides in a matter of few minutes at room temperature, PAP does not induce any polar order. This behavior is in marked contrast to a structurally related, side-chain, nonlinear polyimide, in which the azo chromophore is tethered via a flexible linkage to the polymer backbone. In this case some PAP occurs even at room temperature, while no PAP is observed for a donor-embedded system with a similar T_g. We suggest that the orientation during PAP below T_g in the side-chain polyimide is primarily due to the movement of the azo side chains, and there is a very little coupling of this motion to the main chain. © 1998 John Wiley & Sons, Inc. J Polym Sci B: Polym Phys 36: 1669–1677, 1998     

Synthesis of alkaline‐developable,photosensitive hyperbranched polyimides through the reaction of carboxylic acid dianhydrides and trisamines

Hyperbranched polyimides (HBPI)s with high glass‐transition temperatures and excellent thermal stability were synthesized through the reaction of commercially available carboxylic acid dianhydrides with tris[4‐(4‐aminophenoxy)phenyl]ethane (TAPE). In particular, hyperbranched polyimide HBPI(TAPE‐DSDA), prepared through the reaction of TAPE with 3,3′,4,4′‐diphenylsulfonetetracarboxylic dianhydride (DSDA), showed higher thermal stability and good solubility. Furthermore, alkaline‐developable, photosensitive HBPI(TAPE‐DSDA)‐MA‐CA was prepared through the reaction of HBPI(TAPE‐DSDA) with glycidyl methacrylate with tetrabutylammonium bromide as a catalyst in N‐methyl‐2‐pyrrolidinone (NMP) followed by the addition reaction of cis‐1,2,3,6‐tetrahydrophthalic anhydride with triphenylphosphine as a catalyst in NMP. The glass‐transition temperatures of HBPI(TAPE‐DSDA)‐MA‐CA were greater than 300 °C. A resist composed of 74 wt % HBPI(TAPE‐DSDA)‐MA‐CA, 22.2 wt % trimethylpropane triacrylate, and 3.8 wt % Irgacure 907 as a photoinitiator achieved a resolution of a 55‐μm line pattern and a 275‐μm space pattern by UV irradiation (1000 mJ/cm²). © 2004 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 42: 3697–3707, 2004     

Thiourethane‐based thiol‐ene high Tg networks: Preparation,thermal, mechanical,and physical properties

Thiourethane‐based thiol‐ene (TUTE) films were prepared from diisocyanates, tetrafunctional thiols and trienes. The incorporation of thiourethane linkages into the thiol‐ene networks results in TUTE films with high glass transition temperatures. Increases of T_g were achieved by aging at room temperature and annealing the UV cured films at 85 °C. The aged/annealed film with thiol prepared from isophorone diisocyanate and cured with a 10,080‐mJ/cm² radiant exposure had the highest DMA‐based glass transition temperature (108 °C) and a tan δ peak with a full width at half maximum (FWHM) of 22 °C, indicating a very uniform matrix structure. All of the initially prepared TUTE films exhibited good physical and mechanical properties based on pencil hardness, pendulum hardness, impact, and bending tests. © 2007 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 45: 5103–5111, 2007     

Dielectric properties and molecular mobility of organic/inorganic polymer composites

Microstructure-dielectric properties relationship and molecular mobility of organic/inorganic polymer composites (OIPCs), consisting of polyurethane (PU) and sodium silicate (NaSi), were investigated in this work. Broadband dielectric relaxation spectroscopy (DRS) and thermally stimulated depolarization current (TSDC) techniques were employed. Our interest was focused on the study of the glass transition mechanism and conductivity relaxation. The influence of the molecular weight of PU and inorganic phase content on the dielectric properties of the composites was of particular interest. Glass transition temperature shifts to higher temperatures with the addition of NaSi. The overall molecular mobility was found to increase in the composites, compared to the pure PU matrix. The results are more intense for the composites based on the PU with low molecular weight.     

Synthesis and properties of thermoplastic polyimides with ether and ketone moieties

A series of polyimides containing ether and ketone moieties were synthesized from 1,3‐bis(4‐fluorobenzoyl) benzene and several commercially available dianhydrides via a conventional two‐step polymerization. The inherent viscosities of Polyamide acids ranged from 0.46 to 0.73 dL/g. Thermal properties, mechanical properties, and thermalplasticity of the obtained polimide films were investigated by focusing on the chemical structures of their repeat units. These films were amorphous, flexible, and transparent. All films displayed low T_gs (184–225 °C) but also excellent thermal stability, the 5% weight loss temperature was up to 542 °C under nitrogen. The films showed outstanding mechanical properties with the modulus up to 3.0 GPa and the elongation at break in the range of 8–160%. The uniaxial stretching of PI‐a at high temperature was studied owing to its excellent flexibility. The PI‐a had an elongation at break up to 1600% at 245 °C and the uniaxially stretched film exhibited a much higher modulus (3.9 GPa) and strength (240 MPa) than undrawn film. The results indicated that PI‐a can potentially be used to prepare materials such as fiber, ultra‐thin film or ultra‐high modulus film. All the obtained films also demonstrated excellent thermoplasticity (drop of E′ at T_g > 10³) which made the polyimides more suitable for melt processing. © 2010 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 48: 2878–2884, 2010     

Effect of strain‐induced molecular ordering on mechanical performance and barrier properties of polylactide nanocomposites

Plastic deformation of polylactide has been known as a self‐reinforcement alternative to improve mechanical and barrier properties. In this study, the structural evolution was investigated during a hot‐drawing process, at different initial strain rates and temperatures above T_g of polylactide. The drawing process at T_g +10 °C, led to the formation of an intermediate molecular ordering, between the crystalline and amorphous phases. A lower fraction of this mesomorphic phase was found to develop with the addition of nanoparticles. An increase in the stretching temperature to T_g +30 °C, caused an improvement of the crystallization kinetics, compared to that of thermally activated crystallization. A strain hardening behavior was observed in the presence of mesophase during a stretching process of the hot‐drawn films at room temperature. Permeability was discerned to its basic components, diffusivity, and solubility coefficients. The matrix degradation influenced the permeability components. The diffusivity decreases in the presence of the impermeable matters. © 2017 Wiley Periodicals, Inc. J. Polym. Sci., Part B: Polym. Phys. 2017 , 55, 1865–1876     

Partially bio‐based aromatic polyimides derived from 2,5‐furandicarboxylic acid with high thermal and mechanical properties

Two novel bio‐based diamines are synthesized through introduction of renewable 2,5‐furandicarboxylic acid (2,5‐FDCA), and the corresponding aromatic polyimides (PIs) are then prepared by these diamines with commercially available aromatic dianhydrides via two‐step polycondensation. The partially bio‐based PIs possess high glass transition temperatures (T_gs) in the range from 266 to 364 °C, high thermal stability of 5% weight loss temperatures (T_5%s) over 420 °C in nitrogen and outstanding mechanical properties with tensile strengths of 79–138 MPa, tensile moduli of 2.5–5.4 GPa, and elongations at break of 3.0–12.3%. Some colorless PI films (PI‐1‐b and PI‐1‐c) with the transmittances at 450 nm over 85% are prepared. The overall properties of 2,5‐FDCA‐based PIs are comparable with petroleum‐based PI derived from isophthalic acid, displaying the potential for development of innovative bio‐based materials. © 2018 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2018 , 56, 1058–1066     

Tungsten‐loaded SMP foam nanocomposites with inherent radiopacity and tunable thermo‐mechanical properties

Shape memory polymer (SMP) foams have been developed for use in neurovascular occlusion applications. These materials are predominantly polyurethanes that are known for their biocompatibility and tunable properties. However, these polymers inherently lack X‐ray visibility, which is a significant challenge for their use as implantable materials. Herein, low density, highly porous shape memory polyurethane foams were developed with tungsten nanoparticles dispersed into the foam matrix, at increasing concentrations, to serve as a radiopaque agent. Utilizing X‐ray fluoroscopy sufficient visibility of the foams at small geometries was observed. Thermal characterization of the foams indicated altered thermal response and delayed foam actuation with increasing nanoparticle loading (because of restricted network mobility). Mechanical testing indicated decreased toughness and strength for higher loading because of disruption of the SMP matrix. Overall, filler addition imparted x‐ray visibility to the SMP foams and allowed for tuned control of the transition temperature and actuation kinetics for the material. Copyright © 2015 John Wiley & Sons, Ltd.     

Synthesis and properties of novel polyimides derived from 2,2′,3,3′‐benzophenonetetracarboxylic dianhydride

A new synthetic route to 2,2′,3,3′‐BTDA (where BTDA is benzophenonetetracarboxylic dianhydride), an isomer of 2,3′,3′,4′‐BTDA and 3,3′,4,4′‐BTDA, is described. Single‐crystal X‐ray diffraction analysis of 2,2′,3,3′‐BTDA has shown that this dianhydride has a bent and noncoplanar structure. The polymerizations of 2,2′,3,3′‐BTDA with 4,4′‐oxydianiline (ODA) and 4,4′‐bis(4‐aminophenoxy)benzene (TPEQ) have been investigated with a conventional two‐step process. A trend of cyclic oligomers forming in the reaction of 2,2′,3,3′‐BTDA and ODA has been found and characterized with IR, NMR, matrix‐assisted laser desorption/ionization time‐of‐flight mass spectrometry, and elemental analyses. Films based on 2,2′,3,3′‐BTDA/TPEQ can only be obtained from corresponding polyimide (PI) solutions prepared by chemical imidization because those from their polyamic acids by thermal imidization are brittle. PIs from 2,2′,3,3′‐BTDA have lower inherent viscosities and worse thermal and mechanical properties than the corresponding 2,3′,3′,4′‐BTDA‐ and 3,3′,4,4′‐BTDA‐based PIs. PIs from 2,2′,3,3′‐BTDA and 2,3′,3′,4′‐BTDA are amorphous, whereas those from 3,3′,4,4′‐BTDA have some crystallinity, according to wide‐angle X‐ray diffraction. Furthermore, PIs from 2,2′,3,3′‐BTDA have better solubility, higher glass‐transition temperatures, and higher melt viscosity than those from 2,3′,3′,4′‐BTDA and 3,3′,4,4′‐BTDA. Model compounds have been prepared to explain the order of the glass‐transition temperatures found in the isomeric PI series. The isomer effects on the PI properties are discussed. © 2004 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 42: 2130–2144, 2004     

Molecular modeling study on surface,thermal, mechanical and gas diffusion properties of chitosan

The motivation of this work is to provide reliable and accurate modeling studies of the physical (surface, thermal, mechanical and gas diffusion) properties of chitosan (CS) polymer. Our computational efforts have been devoted to make a comparison of the structural bulk properties of CS with similar type of polymers such as chitin and cellulose through cohesive energy density, solubility parameter, hydrogen bonding, and free volume distribution calculations. Atomistic modeling on CS polymer using molecular mechanics (MM) and molecular dynamics (MD) simulations has been carried out in three dimensionally periodic and effective two dimensionally periodic condensed phases. From the equilibrated structures, surface energies were computed. The equilibrium structure of the films shows an interior region of mass density close to the value in the bulk state. Various components of energetic interactions have been examined in detail to acquire a better insight into the interactions between bulk structure and the film surface. MD simulation (NPT ensemble) has also been used to obtain polymer specific volume as a function of temperature. It is demonstrated that these V–T curves can be used to locate the volumetric glass transition temperature (T_g) reliably. The mechanical properties of CS have been obtained using the strain deformation method. Diffusion coefficients of O₂, N₂, and CO₂ gas molecules at 300 K in CS have been estimated. The calculated properties of CS are comparable with the experimental values reported in the literature. © 2007 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 45: 1260–1270, 2007