The addition of clay on the mechanical properties of surface‐treated CF‐filled PA66 composites

Polyamide 66 (PA66) composites filled with clay and carbon fiber (CF) were prepared by twin‐screw extruder in order to study the influence of nanoparticle reinforcing effect on the mechanical behavior of the PA66 composites (CF/PA66). The mechanical property tests of the composites with and without clay were performed, and the fracture surface morphology was analyzed. The results show that the fracture surface area of the clay‐filled CF/PA66 composite was far smoother than that of the CF/PA66 composite, and there formed a tense interface on the CF surface after the addition of clay. The tensile and flexural strength of CF/PA66 composites with clay was improved. The impact strength decreased because of the high interfacial adhesion. In conclusion, the addition of clay favored the improvement of the higher interface strength and so had good effect on improving the tensile and flexural properties of the composites. Copyright © 2017 John Wiley & Sons, Ltd.     

Modification effects of short carbon fibers on mechanical properties and fretting wear behavior of UHMWPE composites

The present work comparatively studied the modification effects of short carbon fiber (CF) on the mechanical properties and fretting wear behavior of ultra‐high molecular weight polyethylene (UHMWPE)/CF composites. The interactions between CFs and UHMWPE interface were also investigated in detail. The results showed that, with the increase in fiber content, the compressive modulus and hardness of the composites increased, while its impact strength decreased. It was found that filling of CF can reduce the friction and wear of UHMWPE. In addition, the UHMWPE‐based composites reinforced with nitric acid‐treated CF exhibited better mechanical properties, lower friction coefficient, and higher wear resistance than those of untreated UHMWPE/CF composites. This was attributed to the improvement of interfacial adhesion and compatibility between CF and UHMWPE matrix caused by surface chemical modification of CF. Copyright © 2015 John Wiley & Sons, Ltd.     

玻璃纤维对聚甲醛基导电复合材料性能的影响

采用在转矩流变仪中熔融混合的方法制备了聚甲醛(POM)/多壁碳纳米管(MWCNTs)/玻璃纤维(GF)和POM/炭黑(CB)/GF复合材料,研究了GF的加入对复合材料的导电性能、结晶行为和动态力学性能的影响.采用场发射扫描电镜(FESEM)观察了复合材料中导电填料的分散状态,发现GF的加入对MWCNTs和CB的分散状态没有明显影响.虽然GF为导电惰性填料,但因其加入起到了占位作用,明显提高了导电填料的有效浓度,从而使复合材料的体积电阻率明显降低.采用示差扫描量热仪(DSC)研究了复合材料中POM的结晶行为,发现GF的加入对POM的结晶温度、熔点和结晶度均无明显影响.采用动态机械分析仪(DMA)对复合材料的动态力学性能进行了研究,表明GF的加入能够明显地提高复合材料的储能模量.     

Effect of surface treatment of UHMWPE fiber on mechanical and impact fracture behavior of PTFE/POM composites

Ultra‐high‐molecular‐weight polyethylene (UHMWPE) fiber was treated to reinforce the polytetrafluoroethylene/polyoxymethylene (PTFE/POM), and the mechanical properties of surface‐treated UHMWPE were investigated. Scanning electron microscopy was utilized to study the fracture surfaces of UHMWPE/POM/PTFE composites. Experimental results showed that the surface treatment of UHMWPE fiber effectively improves the mechanical property of POM/PTFE composites. Scanning electron microscopy studies indicated that surface modification could improve the interfacial adhesion of POM/PTFE composites. And the dispersion of UHMWPE in POM/PTFE composites was also improved after the surface modification. Copyright © 2017 John Wiley & Sons, Ltd.     

Optimization of tribological behavior of nano clay particle with sisal/jute/glass/epoxy polymer hybrid composites using RSM

The tribological properties are one of the most significant properties in many automobile components such as clutch plate, break shoe, engine liner, piston pin, etc. At present work, attempt on nano clay is loaded with natural fibers (sisal and jute), artificial fiber (E‐glass), and epoxy resin. In this investigation, the specific wear rate and coefficient of friction are analyzed by pin on disc apparatus under dry sliding conditions. The experiment design carried by Box–Behnken design on design of experiment techniques with influence wear parameters, namely, filler content, applied load, sliding distance, and sliding velocity; its responses are analyzed by response surface methodology. The regression mathematical models performed for all the responses, and the most influential factors determined by analysis of variance technique, S/N ratio. The results indicate that the coefficient of friction and specific wear rates are minimized with the addition of filler content to the developed composites and further increasing, the response of composites may be varied. Copyright © 2017 John Wiley & Sons, Ltd.     

Enhanced mechanical properties of carbon fiber composites by grafting different structural poly(amido amine) onto fiber surface

The mechanical properties of carbon fiber composites depend on the interfacial strength between fiber and epoxy matrix. Different poly (amido amine) (PAMAM) dendrimers were grafted onto carbon fiber to improve the interfacial strength of the resulting composites. Functional groups on the carbon fiber surface were examined by X-ray photoelectron spectroscopy. The surface morphology of the resulting materials was characterized by scanning electron microscopy and atomic force microscope. The characterization results revealed that PAMAM dendrimers were chemically grafted onto the surface of carbon fiber. More importantly, the mechanical properties of the resulting composites were enhanced owing to the presence of sufficient functional groups on the carbon fiber surface. In addition, after PAMAM containing chair conformations were grafted, the interlaminar shear strength had the highest increase of 53.13%, higher than that of the fiber grafted with PAMAM containing terminated linear amine. This work provides an alternative approach to enhance the mechanical properties of fiber composites by controlling the interface between fiber and epoxy matrix.     

Influence of Epoxy Resin Treatment on the Mechanical and Tribological Properties of Hemp-Fiber-Reinforced Plant-Derived Polyamide 1010 Biomass Composites

In this study, we investigated the influence of epoxy resin treatment on the mechanical and tribological properties of hemp fiber (HF)-reinforced plant-derived polyamide 1010 (PA1010) biomass composites. HFs were surface-treated using four types of surface treatment methods: (a) alkaline treatment using sodium chlorite (NaClO₂) solution, (b) surface treatment using epoxy resin (EP) solution after NaClO₂ alkaline treatment, (c) surface treatment using an ureidosilane coupling agent after NaClO₂ alkaline treatment (NaClO₂ + A-1160), and (d) surface treatment using epoxy resin solution after the (c) surface treatment (NaClO₂ + A-1160 + EP). The HF/PA1010 biomass composites were extruded using a twin-screw extruder and injection-molded. Their mechanical properties, such as tensile, bending, and dynamic mechanical properties, and tribological properties were evaluated by the ring-on-plate-type sliding wear test. The strength, modulus, specific wear rate, and limiting pv value of HF/PA1010 biomass composites improved with surface treatment using epoxy resin (NaClO₂ + A-1160 + EP). In particular, the bending modulus of NaClO₂ + A-1160 + EP improved by 48% more than that of NaClO₂, and the specific wear rate of NaClO₂ + A-1160 + EP was one-third that of NaClO₂. This may be attributed to the change in the internal microstructure of the composites, such as the interfacial interaction between HF and PA1010 and fiber dispersion. As a result, the mode of friction and wear mechanism of these biomass composites also changed.     

Additive manufacturing of continuous carbon fiber reinforced poly-ether-ether-ketone with ultrahigh mechanical properties

Continuous carbon fiber reinforced poly-ether-ether-ketone (CCF/PEEK) composites have attracted significant interests in mission-critical applications for their exceptional mechanical properties and high thermal resistance. In this study, we additively manufactured CCF/PEEK laminates by the Laser-assisted Laminated Object Manufacturing technique, which was recently reported by the authors. The effects of laser power and consolidation speed on the flexural strength of the CCF/PEEK composites were studied to obtain the optimal process parameters. Hot press postprocessing was performed to further improve the mechanical properties of the composites. Various fiber alignment laminates were prepared, and the flexural and tensile properties were characterized. The hot press postprocessing 3D printed unidirectional CCF/PEEK composites exhibited ultrahigh flexural modulus and strength of 125.7 GPa and 1901.1 MPa, respectively. In addition, the tensile modulus and strength of the composites reached 133.1 GPa and 1513.8 MPa. The results showed that the fabricated CCF/PEEK exhibited superior mechanical performance compare to fused filament fabrication (FFF) printed carbon fiber reinforced thermoplastics (CFRTP).     

A review on plant fiber reinforced thermoset polymers for structural and frictional composites

In recent past years, utilization of synthetic materials has become a matter of immense concern due to increasing environmental awareness in terms of safety, sustainability and maintaining ecological balance. A substantial amount of work has been carried out on various aspects of plant based natural fiber reinforced thermoset polymer composite materials due to their numerous inherent properties like high specific strength, low cost and degradability. Current issues and challenges associated with mechanical and tribological properties of only plant based natural fiber reinforced thermoset composites have been highlighted in the present study. Various factors influencing mechanical and tribological characteristics have been discussed keeping the focus on plant fiber reinforced thermoset composites. A detailed discussion on mechanical (tensile, compressive, flexural, impact strength) and tribological properties (friction and specific wear rate) have been reported. Interfacial adhesion was found to be a dominating factor with respect to mechanical and tribological properties. Wear and frictional characteristics of plant fiber based thermoset composites can be controlled using suitable fillers and reinforcement orientation. A discussion on interfacial adhesion and its effect on composite performance have also been included.     

The effect of surface modification with nitric acid on the mechanical and tribological properties of carbon fiber‐reinforced thermoplastic polyimide composite

Polyacrylamideacrylate (PAN)‐based carbon fibers were submitted to nitric acid oxidation treatments to improve the interfacial adhesion of the carbon fiber (CF)‐reinforced polyimide (CF/PI) composite. The carbon fiber surfaces were characterized by X‐ray photoelectron spectroscopy (XPS). Nitric acid oxidation not only affects the oxygen concentration but also produces an appreciable change in the nature of the chemical functions, namely the conversion of hydroxy‐type oxygen into carboxyl functions. Nitric acid oxidation treatment modifies the element constituting the fiber, the nitrogen concentration being about 1.2 times higher at the fiber external surface compared to the untreated one. The mechanical and tribological properties of the polymide (PI) composites reinforced by the carbon fibers treated with nitric acid oxidation were investigated. Results showed that the tensile strength of the CF/PI composites improved remarkably due to nitric acid treatment along with enhancement in friction and wear performance. Copyright © 2009 John Wiley & Sons, Ltd.     

Effect of Zinc Oxide on Morphology and Mechanical Properties of Polyoxymethylene/Zinc Oxide Composites

This paper studies the effects of zinc oxide (ZnO) on morphology and mechanical properties of pure polyoxymethylene (POM) and POM/ZnO composites. POM/ZnO composites with varying concentration of ZnO were prepared by melt mixing technique in a twin screw extruder. The dispersion of ZnO particles on POM composites was studied by scanning electron microscope (SEM). It is observed that the dispersion of ZnO particles is relatively good. The mechanical properties of the composites such as tensile strength, stress at break, Young's modulus and impact strength were measured. Increasing content of ZnO up to 4.0 wt% increases the impact strength of POM. Addition of ZnO beyond 4.0 wt% decreases the impact strength. The composites containing ZnO content greater than 2.0 wt% show increased Young's Modulus. The tensile strength and stress at break decrease with increasing ZnO content. This may be due to the compatibility between ZnO and POM.     

Mechanical properties, crystallization and melting behaviors of carbon fiber-reinforced PA6 composites

Polyamide-6 (PA6)/carbon fiber (CF) composites were prepared by melt-extrusion via continuous fiber fed during extruding. The mechanical, thermal properties, and crystallization behavior of PA6/CF composites were investigated. It was found that the tensile modulus and strength of the composites were increased with the addition of CF, while their elongations at break were decreased. Scanning electron microscopy observation on the fracture surfaces showed the fine dispersion of CF and strong interfacial adhesion between fibers and matrix. Dynamic mechanical analysis results showed that the storage modulus of PA6/CF composites was improved with the addition of CF. Non-isothermal crystallization analysis showed that the CF plays a role as nucleating agent in PA6 matrix, and the α-form crystalline structure was favorable in the PA6/CF composites, as confirmed from the X-ray diffraction analysis. A trans-crystallization layer around CF could be observed by polarizing optical microscopy, which proved the nucleation effect of carbon fiber surface on the crystallization of PA6. The thermal stability of PA6/CF composites was also enhanced.     

Interfacial studies on the ozone and air‐oxidation‐modified carbon fiber reinforced PEEK composites

In this work, ozone modification method and air‐oxidationwere used for the surface treatment of polyacrylonitrile(PAN)‐based carbon fiber. The surface characteristics of carbon fibers were characterized by XPS. The interfacial properties of carbon fiber‐reinforced (polyetheretherketone) PEEK (CF/PEEK) composites were investigated by means of the single fiber pull‐out tests. As a result, it was found that IFSS (interfacial shear strength) values of the composites with ozone‐treated carbon fiber are increased by 60% compared to that without treatment. XPS results show that ozone treatment increases the amount of carboxyl groups on carbon fiber surface, thus the interfacial adhesion between carbon fiber and PEEK matrix is effectively promoted. The effect of surface treatment of carbon fibers on the tribological properties of CF/PEEKcomposites was comparativelyinvestigated. Experimental results revealed that surface treatment can effectively improve the interfacial adhesion between carbon fiber and PEEK matrix. Thus the wear resistance was significantly improved. Copyright © 2009 John Wiley & Sons, Ltd.     

Effect of atomic oxygen irradiation on the structural and tribological characteristics of polytetrafluoroethylene and its composites

Based on the ground‐based simulation facility, the effects of atomic oxygen (AO) irradiation on the structural and tribological properties of pure polytetrafluoroethylene (PTFE) and carbon fiber and MoS₂‐filled PTFE composites were studied by scanning electron microscopy, X‐ray photoelectron spectroscopy, and a ball‐on‐disc tribometer. The results shown that AO irradiation had significant effects on the structural and tribological properties of pure PTFE, in which the surface morphologies, mass loss, friction coefficient, and wear rate had been changed greatly after AO irradiation. However, it was noticeable that the addition of carbon fiber and MoS₂ filler to PTFE could improve the AO resist capacity and tribological properties of PTFE composites significantly. Copyright © 2016 John Wiley & Sons, Ltd.     

Friction and wear properties of combined surface modified carbon fabric reinforced phenolic composites

Carbon fabric (CF) was surface treated with silane-coupling agent modification, HNO₃ oxidation, combined surface treatment, respectively. The friction and wear properties of the carbon fabric reinforced phenolic composites (CFP), sliding against GCr15 steel rings, were investigated on an M-2000 model ring-on-block test rig. Experimental results revealed that combined surface treatment largely reduced the friction and wear of the CFP composites. Scanning electron microscope (SEM) investigation of the worn surfaces of the CFP composites showed that combined surface modified CFP composite had the strongest interfacial adhesion and the smoothest worn surface under given load and sliding rate. SEM and X-ray photoelectron spectroscopy (XPS) study of carbon fiber surface showed that the fiber surface became rougher and the oxygen concentration increased greatly after combined surface treatment, which improved the adhesion between the fiber and the phenolic resin matrix and hence to improve the friction-reduction and anti-wear properties of the CFP composite.     

石墨烯改性树脂基复合材料力学性能研究进展

树脂基复合材料具有比强度高、比模量大、耐高温、耐腐蚀、质轻等诸多优点,在航天军工、生物医疗、电子封装、体育器材等众多领域得到广泛应用。石墨烯作为一种典型的二维纳米材料,凭借其独特结构以及优异的物理化学性能而备受关注。近年来的研究表明石墨烯可以通过对增强纤维改性和对基体树脂改性的方法来提高树脂基复合材料的力学性能。本文介绍了石墨烯改性树脂基复合材料的增强增韧机理,对石墨烯改性纤维(碳纤维、玻璃纤维、芳纶纤维)增强复合材料以及树脂的改性方法进行了综述;着重阐述了石墨烯改性树脂基复合材料力学性能的研究进展,分析了石墨烯改性树脂基复合材料研究中依旧存在的两大问题,即石墨烯的分散性和界面结合问题,并对石墨烯改性树脂基复合材料的未来发展前景进行了展望。     

Mechanical properties of plasma‐treated carbon fiber reinforced PTFE composites with CNT

This paper is concerned with the effects of the plasma surface treatment and the addition of CNT on the mechanical properties of carbon fiber/polytetrafluoroethylene (PTFE) composite. The tensile and flexural strength of composites containing CNT and plasma‐treated carbon fibers improved. The flexural strength first decreases with respect to the CF content. The flexural strength increases to 179 MPa for the plasma‐treated composite as compared with 167 MPa for the neat carbon fiber composites. The overall improvement is thus nearly 8%.     

Effect of Ionizing Radiation on the Characteristics of EPDM/UHMW-PE Composites

Ultra high molecular weight polyethylene (UHMW-PE) fibers were used in a chopped form and at different concentrations as a reinforcing material in ethylene–propylene–diene terpolymers (EPDM). The effect of radiation dose and fiber concentration on the mechanical properties of the vulcanized rubber composites obtained was measured. It was found that γ-irradiation improves the interfacial adhesion between UHMW-PE fiber (Spectra 1000) and EPDM matrix which was detected by scanning electron microscopy (SEM). In addition, the Young modulus of the composites increases as the irradiation dose increases. Increasing the concentration of the fibers up to 40 phr leads to an enhancement in mechanical properties and swelling resistance of obtained composites, especially in the absence of carbon black. The absolute value of the modulus increased by a factor of at least two with the addition of carbon black. Moreover the tear strength of reinforced and filled EPDM was improved with respect to reinforced rubber. © 1997 John Wiley & Sons, Ltd.     

Thermal transfer,interfacial, and mechanical properties of carbon fiber/polycarbonate-CNT composites using infrared thermography

Electrical resistance (ER) and thermogram measurements were used to evaluate thermal transfer, interfacial and mechanical properties of carbon fiber reinforced thermoplastic polycarbonate composites. Carbon nanotubes (CNTs) were fairly uniformly dispersed in polycarbonates using a solvent dispersion method. The CNTs were then further dispersed with an additional time using a twin screw extruder. The effect of CNT on the mechanical properties of polycarbonate was evaluated using a thin film tensile test. For thermogram to evaluate the transferring temperature the composite was placed on a hotplate and copper wires were inserted in the composite at uniform thickness intervals. Due to the different inherent thermal conductivity of CNT, ER was measured to detect thermal changes in the carbon fiber/CNT-polycarbonate composites. The comparison of interlaminar shear strength (ILSS) was to investigate effects of CNT on mechanical and interfacial properties. The uniform distribution of CNTs affected all of these properties in carbon fiber-reinforced thermoplastic composite. Furthermore, heat transfer and heat release become more rapid with the addition of CNT than the without case.     

Interfacial Characteristics and Fracture Toughness of Electrolytically Ni-Plated Carbon Fiber-Reinforced Phenolic Resin Matrix Composites

The electrolytic plating of metallic nickel on a carbon fiber surface has been carried out in order to improve the interfacial adhesion and the mechanical properties in carbon fiber/phenolic matrix composite systems. The surface and the mechanical interfacial properties of composites are characterized by X-ray photoelectron spectrometry (XPS), surface free energy, and the critical stress intensity factor (K(IC)). From the experimental results, it is clearly revealed that the oxygen functional groups and the metallic nickel on fibers largely affect the mechanical interfacial behavior of the composites, resulting in increased surface polarity, whereas the nitrogen functional groups have no effect. Also, a good correlation between surface oxygen functional groups and mechanical interfacial properties and between wettability and K(IC) is established and it is found that a 10 A m(-2) current density is the optimum condition for this system. Copyright 2001 Academic Press.