Novel sulfonated poly (ether ether ketone)/silica coated carbon nanotubes high‐performance composite membranes for direct methanol fuel cell

The major risk of using carbon nanotubes (CNTs) to modify proton exchange membranes (PEMs) in fuel cells is possible short‐circuiting due to the excellent electrical conductivity of CNTs. In this article, silica‐coated CNTs (SiO₂@CNTs) were successfully prepared by a simple sol–gel process and then used as a new additive in the preparation of sulfonated poly (ether ether ketone) (SPEEK)‐based composite membranes. The insulated and hydrophilic silica coated on the surface of CNTs not only eliminated the risk of short‐circuiting, but also enhanced the interfacial interaction between CNTs and SPEEK, and hence promoted the homogeneous dispersion of CNTs in the SPEEK matrix. Moreover, compared to the methanol permeability of the pure SPEEK membrane (3.42 × 10^?7 cm² s^?1), the SPEEK/SiO₂@CNT composite membrane with a SiO₂@CNT loading of 5 wt% exhibits almost one order of magnitude decrease of methanol crossover, while the proton conductivity still remained above 10^?2 S cm^?1 at room temperature. The obtained results expose the possibility of SPEEK/SiO₂@CNT membranes to be served as high‐performance PEMs in direct methanol fuel cells. Copyright © 2015 John Wiley & Sons, Ltd.     

Sorption and diffusion of methanol and water in PVDF‐g‐PSSA and Nafion® 117 polymer electrolyte membranes

Sorption and diffusion properties of poly(vinylidene fluoride)‐graft‐poly(styrene sulfonic acid) (PVDF‐g‐PSSA) and Nafion® 117 polymer electrolyte membranes were studied in water/methanol mixtures. The two types of membranes were found to have different sorption properties. The Nafion 117 membrane was found to have a maximum in‐solvent uptake around 0.4 to 0.6 mole fraction of methanol, while the PVDF‐g‐PSSA membranes took up less solvent with increasing methanol concentration. The proton NMR spectra were recorded for membranes immersed in deuterated water/methanol mixtures. The spectra showed that the hydroxyl protons inside the membrane exhibit resonance lines different from the resonance lines of hydroxyl protons in the external solvent. The spectral features of the lines of these internal hydroxyl groups in the membranes were different in the Nafion membrane compared with the PVDF‐g‐PSSA membranes. Diffusion measurements with the pulsed field gradient NMR (PFG‐NMR) method showed that the diffusion coefficient of the internal hydroxyl groups in the solvent immersed Nafion membrane mirrors the changes in the diffusion coefficients of hydroxyl and methyl protons in the external solvent. For the PVDF‐g‐PSSA membranes, a decrease in the diffusion coefficient of the internal hydroxyl protons was seen with increasing methanol concentration. These results indicate that the morphology and chemical structure of the membranes have an effect on their solvent sorption and diffusion characteristics. © 2000 John Wiley & Sons, Inc. J Polym Sci B: Polym Phys 38: 3277–3284, 2000     

Preparation and characterization of conductive chitosan–ionic liquid composite membranes

Anhydrous conductive membranes composing of a composite of chitosan (CS) and ionic liquids with symmetrical carboxyl groups were explored. Scanning electron microscope images revealed that porous composite membranes could be obtained by combining CS with different amounts of 1,4‐bis(3‐carboxymethyl‐imidazolium)‐1‐yl butane chloride ([CBIm]Cl). Fourier transform infrared and proton nuclear magnetic resonance confirmed that the formation of ammonium salts after CS was combined with [CBIm]Cl. The thermal property of CS–ionic liquid composite membranes was studied through thermogravimetric analysis. The anhydrous ionic conductivities of CS–[CBIm]X (X = Cl, Ac, BF₄, and I) composite membranes were measured using ac impedance spectroscopy at room temperature in N₂ atmosphere. The conductivities (0.4–0.7 × 10^?4 Scm^?1), found to be in the same range as semiconductors, were significantly higher than those of pure CS membrane (<10^?8 Scm^?1). In addition, the anhydrous conductivity of composite membrane based on CS–[CBIm]I at room temperature reached a level as high as 0.91 × 10^?2 Scm^?1 when iodine was doped. Copyright © 2011 John Wiley & Sons, Ltd.     

燃料电池聚合物电解质膜的研究进展

本文根据聚合物电解质膜燃料电池操作温度、使用的电解质和燃料的不同,将其分为高温质子交换膜燃料电池、低温质子换膜燃料电池、直接甲醇燃料电池和阴离子交换膜燃料电池,综述了它们所用电解质膜的最新进展.第一部分简要介绍了这4种燃料电池的优点和不足.第二部分首先介绍了Nafion膜的结构模型,并对平行柱状纳米水通道模型在介观尺度上进行了修正;接着分别对应用于不同燃料电池的改性膜的改性思路作了分析;最后讨论了用于不同燃料电池的新型质子交换膜的研究,同时列举了性能突出的改性膜和新型质子交换膜.第三部分介绍了阴离子交换膜的研究现状.第四部分对未来聚合物电解质膜的研究作了展望.     

Sulfonated carbon nanotubes/sulfonated poly(ether sulfone ether ketone ketone) composites for polymer electrolyte membranes

A series of composite membranes consisting of sulfonated carbon nanotubes (sCNTs) and sulfonated poly(ether sulfone ether ketone ketone) were successfully fabricated via the solution casting method. The chemical structure, as well as the long‐term stability of the sCNTs in different solvents, was investigated by Fourier transform infrared (FTIR) analysis and solubility experiment, respectively. The morphology, tensile strength, proton conductivity, and methanol permeability of the composite membranes were also investigated. The scanning electron microscope (SEM) observation indicated the good dispersion of the carbon nanotubes in polymer matrix as well as the strong interfacial bonding between the sulfonated poly(ether sulfone ether ketone ketone) (SPESEKK) matrix and sCNTs. The addition of either pristine carbon nanotubes or modified carbon nanotubes significantly enhanced the tensile strength of the SPESEKK membrane. The proton conductivity of the SPESEKK membrane increased while the methanol permeability decreased as the sCNTs content increased, showing a strong interaction between the modified nanotubes and SPESEKK. Copyright © 2010 John Wiley & Sons, Ltd.     

Surface modified multi‐walled carbon nanotubes and Nafion nanocomposite membranes for use in fuel cell applications

The preparation and characterization of the nanocomposite polyelectrolyte membranes, based on Nafion, sulfonated multi‐walled carbon nanotubes (MWCNT‐SO₃H) and imidazole modified multi‐walled carbon nanotubes (MWCNT‐Im), for direct methanol fuel cell applications is described. The results showed that the modification of multi‐walled carbon nanotubes (MWCNT) with proton‐conducting groups (sulfonic acid groups or imidazole groups) could enhance the proton conductivity of the nanocomposite membranes in comparison to Nafion 117. Regarding the interactions between the protonated imidazole groups, grafted on the surface of MWCNT, and the negatively charged sulfonic acid groups of Nafion, new electrostatic interactions can be formed in the interface of the Nafion and MWCNT‐Im, which result in both lower methanol permeability and higher proton conductivity. The physical characteristics of these manufactured nanocomposite membranes were investigated by thermogravimetric analysis, differential scanning calorimetry, Fourier transform infrared spectroscopy, water uptake, methanol permeability, and ion exchange capacity, as well as proton conductivity. The Nafion/MWCNT‐Im membranes showed the higher proton conductivity, lower methanol permeability, and, as a consequence, a higher selectivity parameter in comparison to the neat Nafion or Nafion membrane containing MWCNT‐SO₃H or ─OH functionalized multi‐walled carbon nanotubes (MWCNT‐OH) membranes. The obtained results indicated that the Nafion/MWCNT‐Im membranes could be used as efficient polyelectrolyte membranes for direct methanol fuel cell applications.     

Crosslinked sulfonated polyimide networks as polymer electrolyte membranes in fuel cells

Sulfonated polyimides with tertiary nitrogen in the polymer backbone were synthesized with 1,4,5,8‐naphthalenetetracarboxylic dianhydride, 4,4′‐diaminobiphenyl 2,2′‐disulfonic acid, 2‐bis[4‐(4‐aminophenoxy)phenyl]hexafluoropropane, and diaminoacrydine hemisulfate. They were crosslinked with a series of dibromo alkanes to improve the hydrolytic stability. The crosslinked sulfonated polyimide films were characterized for their thermal stability, ion‐exchange capacity (IEC), water uptake, hydrolytic stability, and proton conductivity. All the sulfonated polyimides had good thermal stability and exhibited a three‐step degradation pattern. With an increase in the alkyl chain length of the crosslinker, IEC decreased as 1.23 > 1.16 > 1.06 > 1.01, and the water uptake decreased as 7.29 > 6.70 > 6.55 > 5.63. The order of the proton conductivity of the crosslinked sulfonated polyimides at 90 °C was as follows: polyimide crosslinked with dibromo butane (0.070) > polyimide crosslinked with dibromo hexane (0.055) > polyimide crosslinked with dibromo decane (0.054). The crosslinked polyimides showed higher hydrolytic stability than the uncrosslinked polyimides. Between the crosslinked polyimides, the hydrolytic stability decreased with an increase in the alkyl chain length of the crosslinker. The crosslinked and uncrosslinked sulfonated polyimides exhibited almost the same proton conductivities. © 2005 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 43: 2370–2379, 2005     

Improving protonic conduction of membranes for polymer electrolyte fuel cells

Method for the modification of proton-conducting Nafion membranes by using a zirconium citrate one-substituted salt, aimed at the improving of characteristics of membranes for polymer-electrolyte-based fuel cells, is suggested. In the method, the membrane is impregnated first with zirconyl chloride and then with citric acid; an insoluble sol is thus formed in the membrane pores. The impregnation is carried out in ultrasound bath, using an isopropyl alcohol-water solvent, to make it more rapid and uniform. It is shown that the impregnation lowers the real component of the membrane impedance. The discharge characteristics of the impregnated and nonimpregnated membranes are compared.     

Theoretical voltammetric response of electrodes coated by solid polymer electrolyte membranes

A model for the differential capacitance of metal electrodes coated by solid polymer electrolyte membranes, with acid/base groups attached to the membrane backbone, and in contact with an electrolyte solution is developed. With proper model parameters, the model is able to predict a limit response, given by Mott–Schottky or Gouy–Chapman–Stern theories depending on the dissociation degree and the density of ionizable acid/base groups. The model is also valid for other ionic membranes with proton donor/acceptor molecules as membrane counterions. Results are discussed in light of the electron transfer rate at membrane-coated electrodes for electrochemical reactions that strongly depend on the double layer structure. In this sense, the model provides a tool towards the understanding of the electro-catalytic activity on modified electrodes. It is shown that local maxima and minima in the differential capacitance as a function of the electrode potential may occur as consequence of the dissociation of acid/base molecular species, in absence of specific adsorption of immobile polymer anions on the electrode surface. Although the model extends the conceptual framework for the interpretation of cyclic voltammograms for these systems and the general theory about electrified interfaces, structural features of real systems are more complex and so, presented results only are qualitatively compared with experiments.     

Using carbon nanotubes to detect polymer transitions

Raman spectral shifts of single‐wall carbon nanotubes embedded in polymer systems were used to measure transitions in polymers. Glass‐transition temperatures and secondary transitions were observed, and Raman spectroscopic data were compared with dynamic mechanical tests for a thermosetting and a thermoplastic polymer. The data confirm that the Raman spectral response of carbon nanotubes embedded in polymers is sensitive to polymer transitions. © 2001 John Wiley & Sons, Inc. J Polym Sci Part B: Polym Phys 39: 1492–1495, 2001     

直接甲醇燃料电池用PEMs的研究进展

本文介绍了用于直接甲醇燃料电池(DMFCs)的质子交换膜(PEMs)的工作原理与性能要求。讨论了影响DMFCs国PEMs的甲醇渗透性能的因素。综述了Nation、改性Nafion膜以及其它新品种膜的研究进展。     

Influence of carboxylated and phosphonated single-walled carbon nanotubes on the transport properties of sulfonated poly(styrene-isobutylene-styrene) membranes

This study discusses the effect of carboxylated (COOH) and phosphonated (PO₃H₂) single-walled carbon nanotubes (SWCNTs) on the transport properties of sulfonated poly(styrene-isobutylene-styrene) (SO₃H SIBS) as polymer nanocomposite membranes (PNMs) for direct methanol fuel cell (DMFC) and chemical and biological protective clothing (CBPC) applications. The properties were determined as a function of sulfonation level of SIBS, SWCNTs functionalization and loading. A comprehensive materials characterization study was performed to understand the interactions between the nanofillers and the functionalized polymer matrix, and to determine the effect of their incorporation on the resulting nanostructure of the PNMs. Results indicate that the sulfonation level is the variable that dictates nanofiller dispersion, mechanical properties, water absorption capabilities, morphology, and oxidative stability of SO₃H SIBS. Meanwhile, the nanofiller loading and functionalization influenced the transport properties. The nanofillers reduced methanol permeation. PO₃H₂ SWCNTs increased the proton conductivity but at a high sulfonation level (i.e., 90 mol %), the ionic interconnectivity caused a more complex morphology decreasing the transport of protons. Optimal selectivity in transport properties were found with a sulfonation level of 61 mol % and a PO₃H₂ SWCNTs loading of 1.0 wt. % for DMFC and 0.5 wt. % for CBPC due to changes in morphology and the unique transport mechanism of permeants through the PNMs. © 2018 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2018 , 56, 2475–2495     

Synthesis and characterization of high molecular weight hexafluoroisopropylidene‐containing polybenzimidazole for high‐temperature polymer electrolyte membrane fuel cells

A high molecular weight, thermally and chemical stable hexafluoroisopropylidene containing polybenzimidazole (6F‐PBI) was synthesized from 3,3′‐diaminobenzidine (TAB) and 2,2‐bis(4‐carboxyphenyl) hexafluoropropane (6F‐diacid) using polyphosphoric acid (PPA) as both the polycondensation agent and the polymerization solvent. Investigation of polymerization conditions to achieve high molecular weight polymers was explored via stepwise temperature control, monomer concentration in PPA, and final polymerization temperature. The polymer characterization included inherent viscosity (I.V.) measurement and GPC as a determination of polymer molecular weight, thermal and chemical stability assessment via thermo gravimetric analysis and Fenton test, respectively. The resulting high molecular weight polymer showed excellent thermal and chemical stability. Phosphoric acid doped 6F‐PBI membranes were prepared using the PPA process. The physiochemical properties of phosphoric acid doped membranes were characterized by measuring the phosphoric acid doping level, mechanical properties, and proton conductivity. These membranes showed higher phosphoric acid doping levels and higher proton conductivities than the membranes prepared by the conventional membrane fabrication processes. These membranes had sufficient mechanical properties to be easily fabricated into membrane electrode assemblies (MEA) and the prepared MEAs were tested in single cell fuel cells under various conditions, with a focus on the high temperature performance and fuel impurity tolerance. © 2009 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 47: 4064–4073, 2009     

A novel composite polymer electrolyte containing room-temperature ionic liquids and heteropolyacids for dye-sensitized solar cells

A novel composite polymeric gel comprising room-temperature ionic liquids (1-butyl-3-methyl-imidazolium-hexafluorophosphate, BMImPF₆) and heteropolyacids (phosphotungstic acid, PWA) in poly(2-hydroxyethyl methacrylate) matrix was successfully prepared and employed as a quasi-solid state electrolyte in dye-sensitized solar cells (DSSCs). These composite polymer electrolytes offered specific benefits over the ionic liquids and heteropolyacids, which effectively enhanced the ionic conductivity of the composite polymer electrolyte. Unsealed devices employing the composite polymer electrolyte with the 3% content of PWA achieved the solar to electrical energy conversion efficiency of 1.68% under irradiation of 50 mW cm⁻² light intensity, increasing by a factor of more than three compared to a DSSC with the blank BMImPF₆-based polymer electrolyte without PWA. It is expected that these composite polymer electrolytes are an attractive alternative to previously reported hole transporting materials for the fabrication of the long-term stable quasi-solid state or solid state DSSCs.     

Achievements in the field of proton-conductive portion electrolyte membranes

The 2000–2006 achievements in the field of synthesis, property examination, and application of proton-exchange membranes are reviewed on the basis of more than 120 papers.     

Proton transport through hydrated chitosan‐based polymer membranes under electric fields

Proton transport is essential in many areas of chemistry and biology and is especially important in the fields of proton exchange membrane fuel cells and biocompatible, protonic semiconductors. These devices make use of membranes to control the flow of protons for either the generation of energy or to more closely couple electronics and biology. In the present study, we make use of ab initio molecular dynamics simulations, including the effect of applied electric fields, to gain atomistic insight into the intrinsic conductivity of chitosan‐based polymers and demonstrate that chitosan does not act as a significant source of friction for the transport of protons while increasing the number of free ions. Published 2017.^? J. Polym. Sci., Part B: Polym. Phys. 2017 , 55 , 1103–1109     

Synthesis of organic sulfobetaine‐based polymer gel electrolyte for dye‐sensitized solar cell application

We have synthesized eco‐friendly, economic, and equally efficient polysulfobetaine‐based gel electrolyte to the alternative of liquid electrolyte in the fabrication of dye‐sensitized solar cells (DSSCs) for the first time. This nitrogen‐rich and highly conductive polysulfobetaine was synthesized by an easy and facile method without the use of any catalyst and explored for its DSSC application. The synthesized polymer gel electrolyte exhibited good ionic conductivity about 6.8 × 10^?3 Scm^?1 at ambient temperatures. DSSCs were fabricated based on this polysulfobetaine gel electrolyte and studied for their performance based on photovoltaic parameters. The DSSC photovoltaic results were appreciable and are Voc = 0.82 V, Jsc = 11.49 mA/cm², FF = 66%, and PCE = 6.26% at 1 sun intensity. These values are slightly lower than conventional liquid electrolyte‐based DSSC shown as Voc = 0.78 V, Jsc = 12.90 mA/cm², FF = 69%, and PCE = 7.07%, both at 100 mWcm^?2. Conductivity and photovoltaic parameters of the device reveals that as prepared polysulfobetaine‐based polymer gel electrolyte may be useful in the fabrication of DSSC and other electrochemical devices. Copyright © 2017 John Wiley & Sons, Ltd.     

Poly(arylene ether ether nitrile)s containing flexible alkylsulfonated side chains for polymer electrolyte membranes

A series of poly(arylene ether ether nitrile)s with different chain lengths of the alkylsulfonates (SPAEEN‐x: x refers number of the methylene units) are successfully synthesized for fuel cell applications. The polymers produced flexible and transparent membranes by solvent casting. The resulting membranes display a high thermal stability, oxidative stability, and higher proton conductivity than that of Nafion 117 at 80 °C and 95% relative humidity (RH). Furthermore, the SPAEEN‐12 with the longest alkylsulfonated side chain exhibits a higher proton conductivity at 30% RH than that of SPAEEN‐6 despite the lower IEC value, which indicates that the introduction of longer alkylsufonated side chains to the polymer main chain induces an efficient proton conduction by the formation of a well‐developed phase‐separated morphology. © 2013 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2014 , 52, 21–29     

Highly phosphonated poly(N‐phenylacrylamide) for proton exchange membranes

A novel highly phosphonated poly(N‐phenylacrylamide) ( PDPAA ) with an ion‐exchange capacity (IEC) of 6.72 mequiv/g was synthesized by the radical polymerization of N‐[2,4‐bis(diethoxyphosphinoyl)phenyl]acrylamide ( DEPAA ), followed by the hydrolysis with trimethylsilyl bromide. Then, the crosslinked PDPAA membrane was successfully prepared by the electrophilic substitution reaction between the aromatic rings of PDPAA and the carbocation formed from hexamethoxymethylmelamine (CYMEL) as a crosslinker in the presence of methanesulfonic acid. The crosslinked PDPAA membrane had high oxidative stability against Fenton's reagent at room temperature. The proton conductivity of the crosslinked PDPAA membrane was 8.8 × 10^?2 S/cm at 95% relative humidity (RH) and 80 °C, which was comparable to Nafion 112. Under low RH, the crosslinked PDPAA membrane showed the proton conductivity of 1.9 × 10^?3 and 4.7 × 10^?5 S/cm at 50 and 30% RH, respectively. The proton conductivity of the crosslinked PDPAA membrane lied in the highest class among the reported phosphonated polymers, and, consequently, the very high local concentration of the acids of PDPAA (IEC = 6.72 mequiv/g) achieved high and effective proton conduction under high RH. © 2010 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2010