Time‐Resolved,In Situ DRIFTS/EDE/MS Studies on Alumina‐Supported Rhodium Catalysts: Effects of Ceriation and Zirconiation on Rhodium–CO Interactions

The effects of ceria and zirconia on the structure–function properties of supported rhodium catalysts (1.6 and 4 wt % Rh/γ‐Al₂O₃) during CO exposure are described. Ceria and zirconia are introduced through two preparation methods: 1) ceria is deposited on γ‐Al₂O₃ from [Ce(acac)₃] and rhodium metal is subsequently added, and 2) through the controlled surface modification (CSM) technique, which involves the decomposition of [M(acac)_x] (M=Ce, x=3; M=Zr, x=4) on Rh/γ‐Al₂O₃. The structure–function correlations of ceria and/or zirconia‐doped rhodium catalysts are investigated by diffuse reflectance infrared Fourier‐transform spectroscopy/energy‐dispersive extended X‐ray absorption spectroscopy/mass spectrometry (DRIFTS/EDE/MS) under time‐resolved, in situ conditions. CeO_x and ZrO₂ facilitate the protection of Rh particles against extensive oxidation in air and CO. Larger Rh core particles of ceriated and zirconiated Rh catalysts prepared by CSM are observed and compared with Rh/γ‐Al₂O₃ samples, whereas supported Rh particles are easily disrupted by CO forming mononuclear Rh geminal dicarbonyl species. DRIFTS results indicate that, through the interaction of CO with ceriated Rh particles, a significantly larger amount of linear CO species form; this suggests the predominance of a metallic Rh phase.     

Structural Characterization of Alumina‐Supported Rh Catalysts: Effects of Ceriation and Zirconiation by using Metal–Organic Precursors

The effects of the addition of ceria and zirconia on the structural properties of supported rhodium catalysts (1.6 and 4 wt % Rh/γ‐Al₂O₃) are studied. Ceria and zirconia are deposited by using two preparation methods. Method I involves the deposition of ceria on γ‐Al₂O₃ from Ce(acac)₃, and the rhodium metal is subsequently added, whereas method II is based on a controlled surface reaction technique, that is, the decomposition of metal–organic M(acac)_x (in which M=Ce, x=3 and M=Zr, x=4) on Rh/γ‐Al₂O₃. The structures of the prepared catalyst materials are characterized ex situ by using N₂ physisorption, transmission electron microscopy, high‐angle annular dark‐field scanning transmission election microscopy, energy‐dispersive X‐ray spectroscopy, X‐ray photoelectron spectroscopy (XPS), and X‐ray absorption fine structure spectroscopy (XAFS). All supported rhodium systems readily oxidize in air at room temperature. By using ceriated and zirconiated precursors, a larger rhodium‐based metallic core fraction is obtained in comparison to the undoped rhodium catalysts, suggesting that ceria and zirconia protect the rhodium particles against extensive oxidation. XPS results indicate that after the calcination and reduction treatments, a small amount of chlorine is retained on the support of all rhodium catalysts. EXAFS analysis shows significant Rh? Cl interactions for Rh/Al₂O₃ and Rh/CeO_x/Al₂O₃ (method I) catalysts. After reaction with H₂/He in situ, for series of samples with 1.6 wt % Rh, the EXAFS first shell analysis affords a mean size of approximately 30 atoms. A broader spread is evident with a 4 wt % rhodium loading (ca. 30–110 atoms), with the incorporation of zirconium providing the largest particle sizes.     

The morphological,optical and electrical properties of SnO2:F thin films prepared by spray pyrolysis

Combining the spray pyrolysis and the sol–gel techniques gives the possibility to produce Fluorine doped Tin oxide (SnO₂:F) thin films. Transparent conducting SnO₂:F thin films have been deposited on glass substrates by the spray pyrolysis technique. This technique for the fabrication of SnO₂:F filmsby combining sol–gel process and the spray pyrolysis technique ispresented in this paper. The Sol–gel precursors have been successfully prepared using SnCl₂·5H₂O and (Ac)F₃. The structural, electrical, and optical properties of these films were investigated. The high resolution transmission electron microscopy (HRTEM) and selected area diffraction (SAD) patterns of SnO₂:F films show that the gel films lead to a tetragonal structure. The X‐ray diffraction pattern of the films deposited at substrate temperature 530° , the orientation of the films was predominantly [110]. In addition, the surface chemical components were also examined by X‐ray photoelectron spectroscopy (XPS) showing the SnO₂:F deposited with the atomic concentration ratios Sn/F 1.82:1. The minimum sheet resistance was 50 Ω and average transmission in the visible wavelength range of 300 to 800 nm was 87.25%. Copyright © 2008 John Wiley & Sons, Ltd.     

Preparation and characterization of antimony-doped SnO2 thin films on gold and silver substrates for electrochemical and surface plasmon resonance studies

The paper reports on the deposition of thin antimony (Sb)-doped SnO₂ films onto gold and silver substrates using magnetron sputtering. The influence of the SnO₂:Sb film on the electrochemical and surface plasmon resonance properties is investigated. The best results in terms of stability, electrochemical and plasmonic characteristics are obtained for SnO₂:Sb of 8.5 nm thickness deposited on silver substrates.     

Incorporating Zn2SnO4 Quantum Dots and Aggregates for Enhanced Performance in Dye‐Sensitized ZnO Solar Cells

The performance of dye‐sensitized ZnO solar cells was improved by a facile surface‐treatment approach through chemical‐bath deposition. After the surface treatment, the quantum dots of Zn₂SnO₄ were deposited onto ZnO nanoparticles accompanied by the aggregations of Zn₂SnO₄ nanoparticles. The ZnO film displayed a better resistance to acidic dye solution on account of the deposited Zn₂SnO₄ nanoparticles. Meanwhile, the open‐circuit photovoltage was greatly enhanced, which can be ascribed to the increased conduction‐band edge of ZnO and inhibited interfacial charge recombination. Although the deposition of Zn₂SnO₄ decreased the adsorption amounts of N719 dye, the aggregates of Zn₂SnO₄ with a size of 350–450 nm acted as the effective light‐scattering layer, thereby resulting in an improved short‐circuit photocurrent. By co‐sensitizing 10 μm‐thick ZnO film with N719 and D131 dyes, a top efficiency of 4.38 % was achieved under the illumination of one sun (AM 1.5, 100 mW cm^?2).     

Synthesis,Solid‐State NMR Characterization,and Application for Hydrogenation Reactions of a Novel Wilkinson’s‐Type Immobilized Catalyst

Silica nanoparticles (SiNPs) were chosen as a solid support material for the immobilization of a new Wilkinson’s‐type catalyst. In a first step, polymer molecules (poly(triphenylphosphine)ethylene (PTPPE); 4‐diphenylphosphine styrene as monomer) were grafted onto the silica nanoparticles by surface‐initiated photoinferter‐mediated polymerization (SI‐PIMP). The catalyst was then created by binding rhodium (Rh) to the polymer side chains, with RhCl₃ ? x H₂O as a precursor. The triphenylphosphine units and rhodium as Rh^I provide an environment to form Wilkinson’s catalyst‐like structures. Employing multinuclear (³¹P, ²⁹Si, and ¹³C) solid‐state NMR spectroscopy (SSNMR), the structure of the catalyst bound to the polymer and the intermediates of the grafting reaction have been characterized. Finally, first applications of this catalyst in hydrogenation reactions employing para‐enriched hydrogen gas (PHIP experiments) and an assessment of its leaching properties are presented.     

SnOx thin films with tunable conductivity for fabrication of p–n homo‐junction

Tin oxide (SnO_x) has been widely used for the fabrication of transparent and flexible devices because of its excellent optical and electronic properties. In this work, we established a methodology for the synthesis of SnO_x thin films with p‐type and n‐type tunable conductivity by direct currecnt (DC) magnetron sputtering. The SnO_x thin films changed from p‐type to n‐type by increasing the relative oxygen partial pressure (ppO₂) from 4.8% to 18.5% and by varying the working pressure between 1.8 and 2.5 mTorr. The SnO_x thin films were annealed at 160°C, 180°C, and 200°C for 30 min to promote the formation of the desired crystalline structures. At the annealing temperature of 180°C in air ambient, the SnO_x thin films showed a tetragonal structure with Sn traces. Having found the optimal conditions, we deposited both types of SnO_x thin films with the same tetragonal structure and similar chemical stoichiometry. Also, the conditions to obtain thin films with the highest mobility values for p‐type (1.10 cm²/Vs) and n‐type (22.20 cm²/Vs) were used for fabricating the device. Finally, the implementation of a SnO_x‐based p–n diode was demonstrated using transparent SnO_x thin films developed in this work, illustrating their potential use in transparent electronics.     

Forming and Gathering of SnO2 Nanoparticles on External Surface of High Silica TON, MFI and FAU Type Zeolites

Tin dioxide （SnO2） nano-particles were prepared on high silica TON, MFI and FAU type zeolites by impregnation of SnC12 solution and subsequent calcination at 873 K. XRD and SAED were used to characterize the crystalline phase, and TEM was used to characterize the morphology, the particle size and the agglomerative state of the formed nano-materials. The nano-particles, which possess 8 nm, 10-80 nm and 6 nm in size, were found to form on the outer surface of TON, MFI and FAU zeolites, respectively. SnO2 microcapsules and SnOz netlike nanostructure were obtained by decomposition of SnO2-TON and SnO2-MFI in 40% hydrofluoric acid at room temperature. Compared with the nano-particles formed on NaY zeolite, the special morphology and the agglomerative state of SnO2 nanostructures on TON and MFI type zeolites with one and two dimension channel system indicate that the heterogeneous framework, surface structure and property perform important function for forming and growing SnO2 nanostructure on the outer surface of the zeolites.     

Surface‐Mediated Synthesis of Dimeric Rhodium Catalysts on MgO: Tracking Changes in the Nuclearity and Ligand Environment of the Catalytically Active Sites by X‐ray Absorption and Infrared Spectroscopies

The preparation of dinuclear rhodium clusters and their use as catalysts is challenging because these clusters are unstable, evolving readily into species with higher nuclearities. We now present a novel synthetic route to generate rhodium dimers on the surface of MgO by a stoichiometrically simple surface‐mediated reaction involving [Rh(C₂H₄)₂] species and H₂. X‐ray absorption and IR spectra were used to characterize the changes in the nuclearity of the essentially molecular surface species as they formed, including the ligands on the rhodium and the metal‐support interactions. The support plays a key role in stabilizing the dinuclear rhodium species, allowing the incorporation of small ligands (ethyl, hydride, and/or CO) and enabling a characterization of the catalytic performance of the supported species for the hydrogenation of ethylene as a function of the metal nuclearity and ligand environment. A change in the nuclearity from one to two Rh atoms leads to a 58‐fold increase in the catalytic activity for ethylene hydrogenation, a reaction involving unsaturated, but stable, dimeric rhodium species.     

Synthesis,characterization and electrocatalytic activity for ethanol oxidation of carbon supported Pt,Pt–Rh,Pt–SnO2 and Pt–Rh–SnO2 nanoclusters

Nanoclusters of Pt, Pt–Rh, Pt–SnO₂ and Pt–Rh–SnO₂ were successfully synthesized by polyol method and deposited on high-area carbon. HRTEM and XRD analysis revealed two phases in the ternary Pt–Rh–SnO₂/C catalyst: solid solution of Rh in Pt and SnO₂. The activity of Pt–Rh–SnO₂/C for ethanol oxidation was found to be much higher than Pt/C and Pt–Rh/C and also superior to Pt–SnO₂/C. Quasi steady-state measurements at various temperatures (30–60 °C), ethanol concentrations (0.01–1 M) and H₂SO₄ concentrations (0.02–0.5 M) showed that Pt–Rh–SnO₂/C is about 20 times more active than Pt/C in the potential range of interest for the fuel cell application.     

Dopants in nanocrystalline tin dioxide

The review surveys studies aimed at constructing new materials for gas sensors based on nanocrystalline tin dioxide. The influence of doping with various impurities (Pt, Pd, Ru, Rh, Cu, Ni, or Fe) on the composition, microstructure, and electrophysical and sensor properties of nanocrystalline SnO₂ was discussed. The conditions for the preparation of powders and thick and thin SnO₂ films by the wet chemical method and aerosol pyrolysis of organometallic compounds are reported. The mechanism of interaction of pure and doped nanocrystalline SnO₂ with a gas phase was analyzed based on the data from Mossbauer, Auger electron, and X-ray photoelectron spectroscopy and the results of in situ Raman spectroscopy, XANES, and conductivity measurements.     

Tin oxide coating on polytetrafluoroethylene films in aqueous solutions

Polytetrafluoroethylene (PTFE) films were successfully coated with tin oxide in aqueous solutions. Tin oxide was crystallized in the solution and formed nanocrystal coatings on the polymer films. The coatings consisted of SnO₂ and SnO crystals. They were assemblies of tin oxide nanosheet of about 10 to 50 nm in size and about 5 nm in thickness. The nanocrystal films can be exfoliated from the PTFE substrates. Tin oxide nanocrystal films had a rough liquid surface and a dense substrate‐side surface. Transparency of PTFE films coated with tin oxide was same as that of bare PTFE films in the range from 400 to 800 nm. The PTFE films coated with tin oxide nanocrystals can be pasted on desired substrates. Copyright © 2009 John Wiley & Sons, Ltd.     

An infrared study of the oxidation of carbon monoxide over supported rhodium catalysts

The reaction of carbon monoxide and oxygen over supported rhodium films has been studied using infrared spectroscopy. The focus of the work was the reactivity of the various CO/Rh/X (X = Al₂O₃, SiO₂, TiO₂) surface states for supported catalysts having high and low Rh loading. Under the reaction conditions the “linear CO” species was the most stable toward oxidation, but this could have been a result of an oxidized Rh surface. A new CO/Rh surface species has been proposed which exhibits an infrared band at 2000 cm⁻¹ for a 0.5% Rh/TiO₂ film. This species is believed to be a bridged carbonyl between Rh¹⁺ and the TiO₂ support.     

Reaction of CO oxidation on platinum,rhodium, a platinum-rhodium alloy,and a heterophase bimetallic platinum/rhodium surface

The reaction of CO oxidation on thin metal films of platinum, rhodium, and their alloy and on a heterophase bimetallic Pt/Rh surface that consisted of platinum particles of size 10–20 nm on the surface of rhodium was studied in the region of low reactant pressures (lower than 2 × 10^?5 mbar). At low temperatures (T < 200°C), the activity of samples increased in the order Rh > Pt/Rh > Pt-Rh alloy > Pt. Above 200°C, the rate of reaction on the heterophase Pt/Rh surface was almost twice as high as the sum of the rates of reaction on the individual metals; this fact is indicative of a synergistic effect. The nature of this effect is considered.     

Synthesis and Structure of [Tp*Rh{P(C7H7)3}] – Competition between the Ligands Tris(3,5‐dimethyl‐1‐pyrazolyl)borate (Tp*) and Tris(1‐cyclohepta‐2,4,6‐trienyl)phosphane. Proof of the κ2(N,B–H) Coordination Mode of the Tp* Ligand

Stepwise introduction of the potential tripod ligands tris(3,5‐dimethyl‐1‐pyrazolyl)borate (Tp*) and tris(1‐cyclohepta‐2,4,6‐trienyl)phosphane into the coordination sphere of rhodium(I) leads mainly to [Tp*Rh{P(C₇H₇)₃}] ( 4 ), in which Tp* is linked to the rhodium through a single pyrazolyl group and a non‐linear B–H–Rh bridge. This is the novel, now firmly established coordination mode κ²(N,B–H). The phosphane ligand is coordinated through one Rh–P and two Rh‐olefin bonds. Important structural features determined for the crystalline state of 4 are retained in solution, as shown by the ¹H, ¹¹B, ¹³C, ³¹P and ¹⁰³Rh NMR spectra.     

Catalysis by the Rh/B system Part 1. Vapour-phase hydroformylation of ethylene at atmospheric pressure on Rh/B on silica

A Rh/B system with rhodium crytallites of small dimensions was formed by reducing rhodium trichloride supported on silica with NaBH₄ atlow temperature. Thermal treatments in Ar and/or in CO/H₂ strongly modify the surface composition but induce only a small modification in the crystallite diameter. After treatment in Ar at 543 K and in CO/H₂ the Rh/B system catalyzes the vapor-phase hydroformylation of ethylene at atmospheric pressure in a flow reactor. The reaction proceeds with very good chemoselectivity toward the hydroformylation products (at 398 K, R is ⩾0.7). The formation of the catalytic species and the surface modifications were studied by X-Ray diffraction, FT—IR and XP spectroscopy. The presence of boron seems to play an important role both in preventing sintering of rhodium particles and in favouring good chemoselectivity toward the hydroformylation reaction.     

Formation of Trinuclear Rhodium‐Hydride Complexes [{Rh(PP*)H}3‐ (μ2‐H)3(μ3‐H)][anion]2—During Asymmetric Hydrogenation?

Recently described and fully characterized trinuclear rhodium‐hydride complexes [{Rh(PP*)H}₃(μ₂‐H)₃(μ₃‐H)][anion]₂ have been investigated with respect to their formation and role under the conditions of asymmetric hydrogenation. Catalyst–substrate complexes with mac (methyl (Z)‐ N‐acetylaminocinnamate) ([Rh(tBu‐BisP*)(mac)]BF₄, [Rh(Tangphos)(mac)]BF₄, [Rh(Me‐BPE)(mac)]BF₄, [Rh(DCPE)(mac)]BF₄, [Rh(DCPB)(mac)]BF₄), as well as rhodium‐hydride species, both mono‐([Rh(Tangphos)‐ H₂(MeOH)₂]BF₄, [Rh(Me‐BPE)H₂(MeOH)₂]BF₄), and dinuclear ([{Rh(DCPE)H}₂(μ₂‐H)₃]BF₄, [{Rh(DCPB)H}₂(μ₂‐H)₃]BF₄), are described. A plausible reaction sequence for the formation of the trinuclear rhodium‐hydride complexes is discussed. Evidence is provided that the presence of multinuclear rhodium‐hydride complexes should be taken into account when discussing the mechanism of rhodium‐promoted asymmetric hydrogenation.     

Photocatalytic activities of multilayered ZnO-based thin films prepared by sol–gel route: effect of SnO2 heterojunction layer

In present study, ZnO/SnO₂/ZnO/SnO₂/ZnO multi–layer, ZnO/SnO₂/ZnO triple layer and ZnO single layer films have been deposited on glass substrate by sol–gel dip–coating technique. The structural and optical properties of thin films have been investigated by X-ray diffractometer, UV–visible, photoluminescence spectroscopies and scanning electron microscopy. The structural analysis reveals structural inhomogeneities and different crystallite growth processes as function of number of deposited layers. A comparison between photocatalytic activity of zinc oxide samples toward photodegradation of phenol, 4-aminophenol and 4-nitrophenol has been performed under UV light irradiation. Experiments were conducted to study the effects of operational parameters on the degradation rate. Pseudo-first-order photodegradation kinetics was observed on all films and the reaction constants were determined. The results showed that the photocatalytic activity of ZnO multi–layer film was superior to that of the ZnO single- and triple-layer films. Differences in film efficiencies can be attributed to differences in crystallinity, surface morphology, defect concentration of oxygen vacancy and to presence of SnO₂ sublayer that may act as trap for electrons generated in the ZnO layer thus preventing electron–hole recombination. The results reveal that SnO₂ hetrojunction layers improve crystalline quality, optical and photocatalytic properties of ZnO multilayered films.     

Tuning the Covering on Gold Surfaces by Grafting Amino-Aryl Films Functionalized with Fe(II) Phthalocyanine: Performance on the Electrocatalysis of Oxygen Reduction

Current selective modification methods, coupled with functionalization through organic or inorganic molecules, are crucial for designing and constructing custom-made molecular materials that act as electroactive interfaces. A versatile method for derivatizing surfaces is through an aryl diazonium salt reduction reaction (DSRR). A prominent feature of this strategy is that it can be carried out on various materials. Using the DSRR, we modified gold surface electrodes with 4-aminebenzene from 4-nitrobenzenediazonium tetrafluoroborate (NBTF), regulating the deposited mass of the aryl film to achieve covering control on the electrode surface. We got different degrees of covering: monolayer, intermediate, and multilayer. Afterwards, the ArNO₂ end groups were electrochemically reduced to ArNH₂ and functionalized with Fe(II)-Phthalocyanine to study the catalytic performance for the oxygen reduction reaction (ORR). The thickness of the electrode covering determines its response in front of ORR. Interestingly, the experimental results showed that an intermediate covering film presents a better electrocatalytic response for ORR, driving the reaction by a four-electron pathway.     

CO\begin{document}$ _{2} $\end{document} Reduction on Metal-Doped SnO\begin{document}$ _{2} $\end{document}(110) Surface Catalysts: Manipulating the Product by Changing the Ratio of Sn:O

The electrocatalytic carbon dioxide reduction reaction (CO₂RR) producing HCOOH and CO is one of the most promising approaches for storing renewable electricity as chemical energy in fuels. SnO₂ is a good catalyst for CO₂-to-HCOOH or CO₂-to-CO conversion, with different crystal planes participating the catalytic process. Among them, (110) surface SnO₂ is very stable and easy to synthesisze. By changing the ratio of Sn: O for SnO₂(110), we have two typical SnO₂ thin films: fully oxidized (stoichiometric) and partially reduced. In this work, we are concerned with different metals (Fe, Co, Ni, Cu, Ru, Rh, Pd, Ag, Os, Ir, Pt, and Au)-doped SnO₂(110) with different activity and selectivity for CO₂RR. All these changes are manipulated by adjusting the ratio of Sn: O in (110) surface. The results show that stochiometric and reduced Cu/Ag doped SnO₂(110) have different selectivity for CO₂RR. More specifically, stochiometric Cu/Ag-doped SnO₂(110) tends to generate CO(g). Meanwhile, the reduced surface tends to generate HCOOH(g). Moreover, we also considered the competitive hydrogen evolution reaction (HER). The catalysts SnO₂(110) doped by Ru, Rh, Pd, Os, Ir, and Pt have high activity for HER, and others are good catalysts for CO₂RR.