Compatibility of tire elastomers using derivative heat flow traces in the glass transition region

Derivative heat flow curves give much more information about the phase heterogeneity of binary blends composed of NR, SBR and BR elastomers thanT _g. In blend compositions, the areas under the derivative heat flow curves appear to be an additive function of the concentration of elastomers in the case of incompatible blends (NR/BR, NR/SBR). They are less than additive for either a partially compatible blend (uncured SBR/BR) or a compatible blend (covulcanized SBR/BR). In the case of 60/40 SBR/BR blends, a DSC (T _0.5) reveals a singleT _g, in conformity with the earlier investigators, whereas the derivative heat flow curve shows two peaks (T _p) indicating incomplete homogenization of the phases. This is a new observation not mentioned in the published literature. Thus, derivative heat flow traces are likely to provide a unique tool to determine compatibility of elastomers. The study also reveals the importance of sample contact with the DSC pan in quantitative determinations.     

Eco-friendly processing oils: A new tool to achieve the improved mileage in tyre tread

People are shifting from use of fossil fuel based processing oils to naturally occurring oils, and restriction on PCA rich extender oils by December 2009 leads to search for naturally occurring oils. According to the KEMI report, products with polycyclic aromatic compounds, PCAs, levels exceeding 3% by weight must be labeled. The report pointed out that worn tyre tread material was being spread on the roadsides, introducing high amounts of PCA into the environment. PCA is having toxic effects on aquatic organisms. In the present work, two naturally occurring oils, neem oil and kurunj oil, were characterised in a 100% Natural Rubber based formulation, a NR/BR blend based Bias Truck and Rib Type Tyre Tread Cap compound and a SSBR/NR/BR blend based Radial Passenger Tyre Tread compound. Compounds made with naturally occurring oils showed better abrasion properties. These oils were found to be suitable also on the basis of low PCA content.     

Investigating the effect of nanolayered silicates on blend segmental dynamics and minor component relaxation behavior in poly(ethylene oxide)/poly(methyl methacrylate) miscible blends

Polymer–silicate nanocomposites based on poly (ethylene oxide), PEO, poly(methyl methacrylate), PMMA, and sodium montmorillonite clay were fabricated and characterized to investigate the effect of nanolayered silicates on segmental dynamics of PEO/PMMA blends. X‐ray results indicate the formation of an exfoliated morphology in the nanocomposites. At low silicate contents, an enhancement in segmental dynamics of blend nanocomposites and also PEO, minor component in blend, is observed at temperature region below blend glass transition. This result can be attributed to the improvement of the confinement effect of rigid PMMA matrix on the PEO chains by introducing a low amount of layered silicates. On the other hand, at high silicate contents, an enhancement in segmental dynamics of blend nanocomposites and PEO is observed at temperature region above blend glass transition. This behavior could be interpreted based on the reduction of monomeric friction between two polymer components, which can facilitate segmental motions of blend components in nanocomposite systems. © 2010 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys, 2011     

Morphology and mechanical and viscoelastic properties of natural rubber and styrene butadiene rubber latex blends

The morphology and mechanical and viscoelastic properties of a series of blends of natural rubber (NR) and styrene butadiene rubber (SBR) latex blends were studied in the uncrosslinked and crosslinked state. The morphology of the NR/SBR blends was analyzed using a scanning electron microscope. The morphology of the blends indicated a two phase structure in which SBR is dispersed as domains in the continuous NR matrix when its content is less than 50%. A cocontinuous morphology was obtained at a 50/50 NR/SBR ratio and phase inversion was seen beyond 50% SBR when NR formed the dispersed phase. The mechanical properties of the blends were studied with special reference to the effect of the blend ratio, surface active agents, vulcanizing system, and time for prevulcanization. As the NR content and time of prevulcanization increased, the mechanical properties such as the tensile strength, modulus, elongation at break, and hardness increased. This was due to the increased degree of crosslinking that leads to the strengthening of the 3‐dimensional network. In most cases the tear strength values increased as the prevulcanization time increased. The mechanical data were compared with theoretical predictions. The effects of the blend ratio and prevulcanization on the dynamic mechanical properties of the blends were investigated at different temperatures and frequencies. All the blends showed two distinct glass‐transition temperatures, indicating that the system is immiscible. It was also found that the glass‐transition temperatures of vulcanized blends are higher than those of unvulcanized blends. The time–temperature superposition and Cole–Cole analysis were made to understand the phase behavior of the blends. The tensile and tear fracture surfaces were examined by a scanning electron microscope to gain an insight into the failure mechanism. © 2000 John Wiley & Sons, Inc. J Polym Sci B: Polym Phys 38: 2189–2211, 2000     

Determination of bound rubber composition of filled SBR/BR blend compounds by analysis of the unbound rubber composition and bound rubber content

Analytical method for determination of the bound rubber composition of a filled SBR/BR blend compound was developed using measurement of the bound rubber content and microstructural analysis of the unbound rubber composition. Various filled SBR/BR blend compounds with different blend ratios were prepared using SBRs with different microstructures. This method included measurement of the bound rubber content, extraction of the unbound rubber, microstructural analysis of the unbound rubber composition, and process for determination of the bound rubber composition. Composition of the unbound rubber was analyzed using liquid proton nuclear magnetic resonance spectroscopy (H-NMR) and transmission Fourier transform infrared spectroscopy (FTIR). It was found that the analytical results using H-NMR had less experimental errors than those using transmission-FTIR. The raw SBR/BR blends were also analyzed in order to evaluate level of the experimental errors. Average SBR/BR ratios of the unbound rubbers were obtained using the 1,2- and 1,4-unit contents determined by the H-NMR analysis. The bound rubber compositions were obtained using the bound rubber contents and the average unbound rubber compositions. It was found that most of the bound rubbers had higher SBR ratios than the formulation value.     

A SAXS and swelling study of cured natural rubber/styrene–butadiene rubber blends

A small‐angle X‐ray scattering (SAXS) and swelling study of natural rubber and styrene–butadiene rubber blends (NR/SBR) is presented. To this aim, specimens of NR and SBR and blends with 75/25, 50/50, and 25/75 NR/SBR ratios (in phr) were prepared at a cure temperature of 433 K and the optimum cure time (t₁₀₀). This time was obtained from rheometer torque curves. The system of cure used in the samples was sulfur/n‐t‐butyl‐2‐benzothiazole sulfenamide. From swelling tests of the cured samples, information about the molecular weight of the network chain between chemical crosslinks was obtained. For all cured compounds, in the Lorentz plots built from SAXS scattering curves, a maximum of the scattering vector q around 0.14 Å^?1 was observed. However, the q position shows a linear‐like shift toward lower values when the SBR content in the SBR/NR blend increases. In pure NR or SBR the q values show a different tendency. The results obtained are discussed in terms of the existence of different levels of vulcanization for each single phase forming the blend and the existence of a third level of vulcanization located in the interfacial NR/SBR layer. © 2009 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 47: 2320–2327, 2009     

Influence of blend miscibility on the proton conductivity and methanol permeability of polymer electrolyte blends

The influence of miscibility on the transport properties of polymer electrolyte blends composed of a proton conductor and an insulator was investigated. The proton‐conductive component in the blends was sulfonated poly(ether ketone ketone) (SPEKK), while the nonconductive component was either poly(ether imide) (PEI) or poly(ether sulfone) (PES). The phase behavior of PEI‐SPEKK blends was strongly influenced by the sulfonation level of the SPEKK. At low sulfonation levels (ion‐exchange capacity (IEC) = 0.8 meq/g), the blends were miscible, while at a slightly higher level (IEC = 1.1 meq/g), they were only partially miscible and for IEC ≥ 1.4 meq/g they were effectively immiscible over the entire composition range. The PES‐SPEKK blends were miscible over the entire range of SPEKK IEC considered in this study (0.8–2.2 meq/g). At high IEC (2.2 meq/g) and at low mass fractions of SPEKK (<0.5), the miscible blends (PES‐SPEKK) had higher proton conductivities and methanol permeabilities than the immiscible ones (PEI‐SPEKK). The opposite relationship was observed for high mass fractions of SPEKK (>0.5). This behavior was explained by the differences in morphology between these two blend systems. At low IEC of SPEKK (0.8 meq/g), where both PEI‐SPEKK and PES‐SPEKK blend systems exhibited miscibility, the transport properties were not significantly different. © 2006 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 44: 2253–2266, 2006     

Spontaneous thinning/thickening deformation observed for plastic blend films and some factors affecting film deformation

The fully amorphous films of highly syndiotactic poly[(R,S)‐3‐hydroxybutyrate] (s‐PHB)/atactic poly(4‐vinylphenol) (PVPh) blends show reversible thinning/thickening phenomena at 37 °C in aqueous medium. On the other hand, isotactic poly[(R)‐3‐hydroxybutyrate] (i‐PHB)/PVPh blend film, in which i‐PHB blend component was partially crystalline, did not show any thinning/thickening phenomena under the same conditions. To elucidate the factors influencing these phenomena, the structure and molecular interaction in these blends were characterized by Fourier transform infrared spectroscopy (FTIR), differential scanning calorimetry, and wide‐angle X‐ray diffraction. The FTIR spectra indicated that the ester carbonyl of PHB and the phenolic hydroxyl of PVPh formed hydrogen bonds in both the thinned and thickened s‐PHB/PVPh blend films. The blend composition, intermolecular hydrogen‐bonding interaction, crystallization behavior, miscibility, and the glass‐transition temperature of the blends affected the thinning/thickening phenomena. Some other polyesters such as poly(?‐caprolactone), poly (L‐lactic acid), atactic poly(D,L‐lactic acid), and poly(ethylene terephthalate) had no ability to exhibit thinning/thickening phenomena in water at 37 °C when they were blended with PVPh. This result implies that s‐PHB/PVPh is the rare example with the ability to show reversible thinning/thickening phenomena. © 2002 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 40: 2736–2743, 2002     

Miscibility and surface properties of fluorinated copolymer blends involving hydrogen‐bonding interactions

The miscibility and underlying hydrogen‐bonding interactions of blends of a fluorinated copolymer containing pyridine and a nonfluorinated copolymer containing methacrylic acid were studied with differential scanning calorimetry (DSC), transmission Fourier transform infrared (TX‐FTIR) spectroscopy, and X‐ray photoelectron spectroscopy (XPS), whereas the surface properties of the blends were investigated with contact‐angle measurements, time‐of‐flight secondary‐ion mass spectroscopy, XPS, and attenuated total reflectance Fourier transform infrared spectroscopy. DSC studies showed that the presence of a sufficient amount of 4‐vinylpyridine units in the fluorinated copolymer produced miscible blends with the nonfluorinated copolymer containing methacrylic acid. TX‐FTIR and XPS showed the existence of pyridine–acid interpolymer hydrogen‐bonding interactions. Even though the anchoring effect of hydrogen bonding hindered the migration of the fluorinated component to the blend surface, it could not completely eliminate the surface enrichment of the fluorinated component and the surface rearrangement of the fluorinated pendant chain. The air–blend interface was mainly occupied by the fluorinated pendant chain, and the surface energies of the blends were extremely low, even with only 1.5 wt % of the fluorinated component in the blends. © 2004 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 42: 1145–1154, 2004     

Friction and wear mechanisms of polyamide 66/high density polyethylene blends

Polyamide 66 (PA66)/high density polyethylene (HDPE) blends having miscible structure were produced by compatibilization of HDPE grafted with maleic anhydride (HDPE‐g‐MAH). Mechanical and tribological properties of blends in different compositions were tested. It was found that the polymer blends greatly improved the mechanical properties of PA66 and HDPE. Blending HDPE with PA66 significantly decreased the friction coefficient of PA66; the friction coefficients of blends with different compositions were almost the same and approximately equal to that of pure HDPE; the blends with 80 vol % PA66 exhibited the best wear resistance. The transfer films, counterpart surfaces, and wear debris formed during sliding were investigated by Scanning Electron Microscopy (SEM), and Differential Scanning Calorimetry (DSC) analysis was further carried out on wear debris. These investigations indicated that the thermal control of friction model is applicable to PA66/HDPE blend, that is the friction coefficient of blend is governed by the HDPE component, which possesses a lower softening point relative to the PA66 component in this system. The wear mechanism of PA66/HDPE blend transforms from PA66 to HDPE as the HDPE content increases. PA66, as the component with higher softening point, increases the hardness of blend, enhances the ability of blend to form a transfer film on the counterface, and inhibits the formation of larger belt‐like debris of HDPE, at the same time, the presence of self‐lubricating HDPE in the system decreases the friction coefficient and the frictional heat, all of these factors are favorable for the wear resistance of PA66/HDPE blend. © 2005 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 43: 2514–2523, 2005     

Raman spectroscopy and thermal analysis of gum and silica-filled NR/SBR blends prepared from latex system

Natural rubber/styrene-butadiene rubber (NR/SBR) blends, with and without silica, were prepared by co-coagulating the mixture of rubber latices and various amounts of well-dispersed silica suspension. An attempt to predict blend compositions was made using Raman spectroscopy in association with differential scanning calorimetry (DSC) and thermogravimetric analysis (TGA). It was found that the intensity of each Raman characteristic peak was strongly dependent on the blend composition, but there was no significant evolution with the presence of silica. Also, TGA results revealed an improvement in thermal stability of NR/SBR blends with increasing both SBR and silica contents due to the dilution effect. Two distinct glass transition temperatures (T_g) were observed in DSC thermograms of all blends, and their T_g values were independent on both blend composition and silica content. This indicated a physical blend formation, which agreed well with no shifts in Raman peaks of the blends in comparison with those of the individual rubbers. Linear regression with R² quality factor close to 0.99 was achieved when plotting intensity ratio at 1371/1302 cm^?1 versus blend ratios. On the other hand, the peak height ratio and heat capacity ratio from TGA and DSC analysis, respectively, yielded quadratic equations as a function of blend ratios.     

Thermorheological complexity of poly(methyl methacrylate)/poly(vinylidene fluoride) miscible polymer blend: Terminal and segmental levels

Oscillatory shear rheometry data for a miscible blend of 20 wt % poly(vinylidene fluoride) (PVDF) in poly(methyl methacrylate) (PMMA) shows breakdown of time–temperature superposition for this blend. A comparison between glass transition temperature which PMMA chains sense in the blend and effective glass transition temperature of this component indicates that, the Lodge–McLeish model can describe terminal dynamics of PMMA. In addition, terminal dynamics of PVDF chains in the blend is similar to that of its pure state in agreement with the mentioned model. At segmental level, dynamic mechanical thermal analysis of four wholly amorphous blends suggests that cooperativity of molecular motions decreases upon addition of 30 and 40 wt % PVDF to PMMA. This behavior has been confirmed via calculation of degree of fragility which presumably is attributed to strong tendency of PVDF chains to self‐association rather than inter‐association with PMMA chains according to the FTIR results. © 2007 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 45: 2860–2870, 2007     

Compatibilization efficiency of styrene–butadiene multiblock copolymers in PS/PP blends

The compatibilizing effect of di‐, tri‐, penta‐, and heptablock (two types) copolymers with styrene and butadiene blocks was studied in polystyrene/polypropylene (PS/PP) 4/1 blends. The structure of PS/PP blends with the addition of 5 or 10 wt % of a block copolymer (BC) was determined on several scale levels by means of transmission electron microscopy (TEM) and small‐angle X‐ray scattering (SAXS). The results of the structure analysis were correlated with measured stress‐transfer properties: elongation at break, impact, and tensile strength. Despite the fact that the molar mass of the PS blocks in all the BCs used was about 10,000, that is, below the critical value M^* (～18,000) necessary for the formation of entanglements of PS chains, all the BCs used were found to be good compatibilizers. According to TEM, a certain amount of a BC is localized at the interface in all the analyzed samples, and this results in a finer dispersion of the PP particles in the PS matrix, the effect being more pronounced with S‐B‐S triblock and S‐B‐S‐B‐S pentablock copolymers. The addition of these two BCs to the PS/PP blend also has the most pronounced effect on the improvement of mechanical properties of these blends. Hence, these two BCs can be assumed to be better compatibilizers for the PS/PP (4/1) blend than the S‐B diblock as well as both S‐B‐S‐B‐S‐B‐S and B‐S‐B‐S‐B‐S‐B heptablock copolymers. In both types of PS/PP/BC blends (5 or 10 wt % BC), the BC added was distributed between both the PS/PP interface and the PS phase, and, according to SAXS, it maintained a more or less ordered supermolecular structure of neat BCs. © 2001 John Wiley & Sons, Inc. J Polym Sci B: Polym Phys 39: 931–942, 2001     

Rhythmic growth of ring‐banded spherulites in blends of liquid crystalline methoxy‐poly(aryl ether ketone) and poly(aryl ether ether ketone)

Rhythmic growth of ring‐banded spherulites in blends of liquid crystalline methoxy‐poly(aryl ether ketone) (M‐PAEK) and poly(aryl ether ether ketone) (PEEK) has been investigated by means of differential scanning calorimetry (DSC), polarized light microscopy (PLM), and scanning electron microscopy (SEM) techniques. The measurements reveal that the formation of the rhythmically grown ring‐banded spherulites in the M‐PAEK/PEEK blends is strongly dependent on the blend composition. In the M‐PAEK‐rich blends, upon cooling, an unusual ring‐banded spherulite is formed, which is ascribed to structural discontinuity caused by a rhythmic radial growth. For the 50:50 M‐PAEK/PEEK blend, ring‐banded spherulites and individual PEEK spherulites coexist in the system. In the blends with PEEK as the predominant component, M‐PAEK is rejected into the boundary of PEEK spherulites. The cooling rate and crystallization temperature have great effect on the phase behavior, especially the ring‐banded spherulite formation in the blends. In addition, the effects of M‐PAEK phase transition rate and phase separation rate on banded spherulite formation is discussed. © 2007 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 45: 3011–3024, 2007     

Effect of PBT molecular weight and reactive compatibilization on the dispersed‐phase coalescence of PBT/SAN blends

Poly(butylene terephthalate) (PBT)/styrene‐acrylonitrile copolymer (SAN) blends were investigated with respect to their phase morphology. The SAN component was kept as dispersed phase and PBT as matrix phase and the PBT/SAN viscosity ratio was changed by using different PBT molecular weights. PBT/SAN blends were also compatibilized by adding methyl methacrylate‐co‐glycidyl methacrylate‐co‐ethyl acrylate terpolymer, MGE, which is an in situ reactive compatibilizer for melt blending. In noncompatibilized blends, the dispersed phase particle size increased with SAN concentration due to coalescence effects. Static coalescence experiments showed evidence of greater coalescence in blends with higher viscosity ratios. For noncompatibilized PBT/SAN/MGE blends with high molecular weight PBT as matrix phase, the average particle size of SAN phase does not depend on the SAN concentration in the blends. However noncompatibilized blends with low molecular weight PBT showed a significant increase in SAN particle size with the SAN concentration. The effect of MGE epoxy content and MGE molecular weight on the morphology of the PBT/SAN blend was also investigated. As the MGE epoxy content increased, the average particle size of SAN initially decreased with both high and low molecular weight PBT phase, thereafter leveling off with a critical content of epoxy groups in the blend. This critical content was higher in the blends containing low molecular weight PBT than in those with high molecular weight PBT. At a fixed MGE epoxy content, a decrease in MGE molecular weight yielded PBT/SAN blends with dispersed nanoparticles with an average size of about 40 nm. © 2010 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys, 2010     

Radiation effects on SBR–EPDM blends: A correlation with blend morphology

The effect of γ radiation on the morphological and physical properties of Styrene–butadiene rubber (SBR) and Ethylene–propylene–diene monomer (EPDM) blends has been investigated. An attempt has been made to establish a correlation between various parameters like Gordon–Taylor parameter (k), hydrodynamic interaction parameter (Δ[η]_mix), chemical shift factor (b), Charlesby–Pinner parameter (p₀/q₀) and polymer–polymer interaction parameter (χ). The results showed a close dependence of mechanical and physical properties of irradiated blends on these parameters. The probability of spur overlap has been found to increase with the increase in EPDM content in the blends, which in turn results in significant improvement in the mechanical properties of the irradiated SBR–EPDM blends with higher EPDM fraction. The efficiency of four multifunctional acrylates as crosslinking aid for the radiation‐induced vulcanization of SBR–EPDM blend was also studied. The results established lower efficiency of methacrylates over acrylates in the process and indicated that among the crosslinking agents studied trimethylolpropane triacrylate is the most efficient one. © 2006 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 44: 1676–1689, 2006     

The effect of compatibilization on the dynamic properties of polypropylene/nylon‐6 blends studied by broad band dielectric spectroscopy

Polypropylene (PP) and polyamide‐6 (Ny‐6) blends with a 70/30 composition have been studied by broadband dielectric spectroscopy. The unmodified blends are immiscible, and 10% of PP functionalized with maleic anhydride was added as a compatibilizer. The influence of the compatibilizer on the water sorption and on the molecular dynamics of the Ny‐6 phase is followed by the changes induced in the dielectric loss spectra of these blends in both wet and dry states. The shortest range motions are unaffected by the compatibilizer in the dry state, but a higher water sorption is observed in the unmodified blend. Higher activation energies are found for the β relaxation in the dry blends than for the Ny‐6 homopolymer, showing the existence of constraints on these longer scale motions. During increasing temperature experiments, two segmental modes are recorded, the lower temperature mode corresponding to the plasticized material; as the temperature is raised, a second cooperative mode is found, originating in the dry Ny‐6 amorphous phase, rigidized by the loss of moisture. The comparison of the dielectric strengths of the modes shows that the unmodified blend absorbs more water than the compatibilized blend. The segmental dynamics are unaffected by compatibilization. At high temperatures, the high temperature tail of the segmental mode is much higher in the absence of the compatibilizer. The contribution of a peak due to interfacial polarization is lowered by the presence of the compatibilizer, which makes the interface more diffuse and the trapping of free carriers less effective. © 2005 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 43: 1408–1420, 2005     

The influence of the arrangement of styrene in methyl methacrylate/butadiene/styrene on the properties of PMMA/SAN/MBS blends

A series of methyl methacrylate‐butadiene‐styrene (MBS) core–shell impact modifiers were prepared by grafting styrene (St) and methyl methacrylate (MMA) onto polybutadiene (PB) or styrene‐butadiene rubber (SBR) seed latex in emulsion polymerization. All the MBS modifiers were designed to have the same total chemical composition, and Bd/St/MMA equaled 39/31/30, which was a prerequisite for producing transparent blends with poly(MMA)/styrene‐acrylonitrile (PMMA/SAN) matrix copolymers. Under this composition, different ways of arrangement for styrene in MBS led to the different structure of MBS modifier. The concentration of PB or SBR rubber of MBS in PMMA/SAN/MBS blends was kept at a constant value of 15 wt.%. The effects of arrangement of St in MBS on the mechanical and optical properties of PMMA/SAN/MBS blends were investigated. The results indicated that Izod impact strength of PMMMA/SAN/MBS blend with the amount of St grafted on core in MBS was higher than that of blend with the amount of St copolymerized with Bd in core of MBS, while the transparency of blend is opposite. From transmission electron microscopy, it was found that the arrangement of St in MBS influenced the dispersion of blend, which led to different toughness. Copyright © 2013 John Wiley & Sons, Ltd.     

Miscibility and phase structure of binary blends of polylactide and poly(methyl methacrylate)

Blends of amorphous poly(DL‐lactide) (DL‐PLA) and crystalline poly(L‐lactide) (PLLA) with poly(methyl methacrylate) (PMMA) were prepared by both solution/precipitation and solution‐casting film methods. The miscibility, crystallization behavior, and component interaction of these blends were examined by differential scanning calorimetry. Only one glass‐transition temperature (T_g) was found in the DL‐PLA/PMMA solution/precipitation blends, indicating miscibility in this system. Two isolated T_g's appeared in the DL‐PLA/PMMA solution‐casting film blends, suggesting two segregated phases in the blend system, but evidence showed that two components were partially miscible. In the PLLA/PMMA blend, the crystallization of PLLA was greatly restricted by amorphous PMMA. Once the thermal history of the blend was destroyed, PLLA and PMMA were miscible. The T_g composition relationship for both DL‐PLA/PMMA and PLLA/PMMA miscible systems obeyed the Gordon–Taylor equation. Experiment results indicated that there is no more favorable trend of DL‐PLA to form miscible blends with PMMA than PLLA when PLLA is in the amorphous state. © 2002 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 41: 23–30, 2003     

The effect of various compatibilizers on thermal,mechanical, and morphological properties of polystyrene/polypropylene blends

The effects of various compatibilizers on thermal, mechanical and morphological properties of 50/50 polypropylene/polystyrene blends were investigated. Various compatibilizers, polystyrene-(ethylene/butylenes/ styrene) (SEBS), ethylene vinyl acetate (EVA), polystyrene-butylene rubber (SBR) and blend of compatibilizers SEBS/PP-g-MAH, EVA/PP-g-MAH, and SBR/PP-g-MAH were used. Differential scanning calorimetry, thermogravimetric analysis, wide-angle X-ray scattering, scanning electron microscopy, microhardness, and Izod impact strength were adopted. It was found that the influence of various compatibilizers was appeared on all the properties studied. The properties of the blends compatibilized with SEBS, EVA, and SBR are very distinct from those of blends compatibilized with blend of compatibilizers. Results show that compatibilized blends with the blend of compatibilizers EVA/PP-g-MAH, SBR/PP-g-MAH, and SEBS/PP-g-MAH or SBR were relatively more stable than the uncompatibilized blend and blend compatibilized with SEBS or EVA. The compatibilizer does not only reduce the interfacial tension or increase the phase interfacial adhesion between the immiscible polymers, but greatly affects the degree of crystallinity of blends.