Fine structure of poly(vinylidene fluoride) membranes prepared by phase inversion from a water/N‐methyl‐2‐pyrollidone/poly(vinylidene fluoride) system

Poly(vinylidene fluoride) (PVDF) membranes were prepared by the isothermal immersion and precipitation of PVDF/N‐methyl‐2‐pyrollidone dope solutions in either harsh or soft nonsolvent baths. Low‐voltage field emission scanning electron microscopy imaging of the formed membranes at high magnifications (e.g., 300,000×) revealed their nanoscale fine structures, particularly dendrites observed on the surfaces of the macrovoids, cellular pores, and the membrane skin, which have never been successfully presented in the literature. Evidence of crystallization was also demonstrated by X‐ray diffraction and differential scanning calorimetry measurements. The phase diagram at 25 °C, including a binodal, tie lines, and a crystallization‐induced gelation line, was determined both experimentally and theoretically. These results were further used in mass‐transfer calculations to obtain diffusion trajectories and concentration profiles for the membrane region, which were useful for elucidating the relationship between the membrane preparation conditions and the obtained membrane morphologies. © 2004 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 42: 830–842, 2004     

Development of oriented structure and properties on drawing of poly(vinylidene fluoride) by solid‐state coextrusion

Gel films of poly(vinylidene fluoride) (PVDF) consisting of α‐form crystals were drawn uniaxially by solid‐state coextrusion to extrusion draw ratios (EDR) up to 9 at an optimum extrusion temperature of 160 °C, about 10°C below the melting temperature (T_m). The development of an oriented structure and mechanical and electrical properties on coextrusion drawing were studied as a function of EDR. Wide‐angle X‐ray diffraction patterns showed that the α crystals in the original gel films were progressively transformed into oriented β‐form crystals with increasing EDR. At the highest EDR of 9 achieved, the drawn product consisted of a highly oriented fibrous morphology with only β crystals even for the draw near the T_m. The dynamic Young's modulus along the draw direction also increased with EDR up to 10.5 GPa at the maximum EDR of 9. The electrical properties of ferroelectricity and piezoelectricity were also markedly enhanced on solid‐state coextrusion. The D–E square hysteresis loop became significantly sharper with EDR, and a remanent polarization P_r of 100 mC/m² and electromechanical coupling factor along the thickness direction k_t of 0.27 were achieved at the maximum EDR of 9. The crystallinity value of 73–80% for the EDR 9 film, estimated from these electrical properties, compares well with that calculated by the ratio of the crystallite size along the chain axis to the meridional small‐angle X‐ray scattering (SAXS) long period, showing the average thickness of the lamellae within the drawn β film. These results, as well as the appearance of a strong SAXS maximum, suggest that the oriented structure and properties of the β‐PVDF are better explained in terms of a crystal/amorphous series arrangement along the draw axis. Further, the mechanical and electrical properties obtained in this work are the highest among those ever reported for a β‐PVDF, and the latter approaches those observed for the vinylidene fluoride and trifluoroethylene copolymers. © 2001 John Wiley & Sons, Inc. J Polym Sci Part B: Polym Phys 39: 1371–1380, 2001     

Polymorphism Control of Poly(vinylidene fluoride) through Electrospinning

Polymorphism control of PVDF has been realized through electrospinning. PVDF fibrous membranes with fiber diameter in the range of 100 nm to several micrometers were produced by electrospinning and the crystal phase of electrospun PVDF fibers can be adjusted at the same time. Through the control of electrospinning parameters such as the solvent, electrospinning temperature, feeding rate, and tip‐to‐collector distance, PVDF fibrous membranes containing mainly α‐ or β‐ or γ‐phase could be fabricated successfully.

     

Fine structure and formation mechanism of particulate phase‐inversion poly(vinylidene fluoride) membranes

The structure and formation mechanism of a microporous phase‐inversion poly(vinylidene fluoride) (PVDF) membrane exhibiting a relatively loosely packed agglomerate of semicrystalline globules are explored. The membrane has been prepared by the coagulation of a solution of PVDF in dimethylformamide by the action of 1‐octanol, which is a soft nonsolvent. Experimental observations pertain to the globule surface, which is dominated by a grainy nanostructure; the globular interior, which exhibits a range of fine structures (e.g., twisted sheets and treelike branches); and the globule–globule connections, which exhibit a sheetlike or ropelike structure. On the basis of the observed structural details and phase diagram considerations, it is proposed that the membrane structure is the result of a unique combination of a polymer crystallization and a liquid–liquid phase‐separation process, with end‐result globular structural features of remarkable uniformity. © 2003 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 41: 1578–1588, 2003     

Enhanced electrical properties of highly oriented poly(vinylidene fluoride) films prepared by solid‐state coextrusion

Oriented poly(vinylidene fluoride) (PVDF) films with β‐form crystals have been commonly prepared by cold drawing of a melt‐quenched film consisting of α‐form crystals. In this study, we have successfully produced highly oriented PVDF thin films (20 µm thick) with β‐crystals and a high crystallinity (55–76%), by solid‐state coextrusion of a gel film to eight times the original length at an established optimum extrusion temperature of 160°C, some 10°C below the melting temperature. The resultant drawn films had a highly oriented (orientation function f_c = 0.993) fibrous structure, showing high mechanical properties of an extensional elastic modulus of 8.3 GPa and tensile strength of 0.84 GPa, along the draw direction. Such highly oriented and crystalline films exhibited excellent ferroelectric and piezoelectric properties. The square hysteresis loop was significantly sharper than that of a conventional sample. The sharp switching transient yielded the remnant polarization P_r of 90 mC/m², and the electromechanical coupling factor k_t was 0.24 at room temperature. These values are about 1.5 times greater than those of a conventional β‐PVDF film. Thus, solid‐state coextrusion near the melting point was found to be a useful technique for the preparation of highly oriented and highly crystalline β‐PVDF films with superior mechanical and electrical properties. The morphology of the extrudate relevant to such properties is discussed. © 1999 John Wiley & Sons, Inc. J Polym Sci B: Polym Phys 37: 2549–2556, 1999     

The morphology of poly(vinylidene fluoride) crystallized from blends of poly(vinylidene fluoride) and poly(ethyl acrylate)

A combined optical and electron microscopical study has been carried out of the crystallization habits of poly(vinylidene fluoride) (PVF₂) when it is crystallized from blends with noncrystallizable poly(ethyl acrylate) (PEA). The PVF₂/PEA weight ratios were 0.5/99.5,5/95, and 15/85. Isothermal crystallization upon cooling the blends from the single-phase liquid region was carried out in the range 135–155°C, in which the polymer crystallizes in the α-orthorhombic unit cell form. The 0.5/99.5 blend yielded multilayered and planar lamellar crystals. The lamellae formed at low undercoolings were lozenge shaped and bounded laterally by {110} faces. This habit is prototypical of the dendritic lateral habits exhibited by the crystals grown from the same blend at high undercoolings as well as by the constituent lamellae in the incipient spherulitic aggregates and banded spherulites that formed from the 5/95 and the 15/85 blends, respectively. In contrast with the planar crystals grown from the 0.5/99.5 blend, the formation of the aggregates grown from the 5/95 blend is governed by a conformationally complex motif of dendritic lamellar growth and proliferation. The development of these aggregates is characterized by the twisting of the orientation of lamellae about their preferential b-axis direction of growth, coupled with a fan-like splaying or spreading of lamellae about that axis. The radial growth in the banded spherulites formed from the 15/85 blend is governed by a radially periodic repetition of a similar lamellar twisting/fan-like spreading growth motif whose recurrence corresponds to the extinction band spacing. This motif differs in its fan-like splaying component from banding due to just a helicoidal twisting of lamellae about the radial direction. © 1993 John Wiley & Sons, Inc.     

Structure and pH‐sensitive properties of poly (vinylidene fluoride) membrane changed by blending poly (acrylic acid) microgels

pH‐sensitive poly (vinylidene fluoride) (PVDF)/poly (acrylic acid) (PAA) microgels membranes are prepared by phase inversion of the N, N‐dimethylformamide solution containing PAA microgels and PVDF in aqueous solution. The composition and structure of the blend membrane are investigated by Fourier transform infrared spectra, X‐ray photoelectron spectroscopy measurements, thermo gravimetric analysis, field‐emission scanning electron microscope and atomic force microscope. The results indicate the surface and cross section of the blend membranes have a porous structure with PAA microgels immobilized inside the pore and on the membrane surface. The blend PVDF membranes exhibit pH‐sensitive water flux, with the most drastic change in permeability observed between pH 3.7 and 6.3. The blend membranes are fouled by bovine serum albumin, and their antifouling property is enhanced by increasing PAA microgels, mainly derived from the improved hydrophilic property. Copyright © 2013 John Wiley & Sons, Ltd.     

Effect of annealing on the structure and properties of poly(vinylidene fluoride) β‐form films

Oriented poly(vinylidene fluoride) (PVDF) films consisting of β crystals were prepared by the solid‐state coextrusion (SC) of a gel film near the melting temperature (T_m) and by conventional cold tensile drawing (TD) of a melt‐quenched film. These films were annealed over the temperature range of 75–190 °C (below and above the static T_m) while the sample length was kept constant or constant loads were applied. After annealing with the sample length kept constant, the dynamic Young's modulus markedly decreased because of the relaxation of oriented amorphous chains, as shown by infrared spectroscopy. In contrast, annealing under a constant load improved the chain orientation in both the crystalline and amorphous regions, resulting in an increase in the modulus from an initial 10.5 to 14.3 GPa for the SC and from an initial 3.3 to 4.8 GPa for the TD. The SC, annealed at 190 °C with a constant load corresponding to an initial tension of 200 MPa, exhibited an extreme crystalline‐chain orientation of 0.998 and a modulus of 14.3 GPa, among the highest values ever reported for PVDF. Although the remanent polarization (P_r) of the TD increased slightly from the initial 62 to 68 mC/m², P_r of the SC stayed constant at 100 mC/m² independently of the annealing conditions. This suggests that the P_r value of 100 mC/m² approached the equilibrium value for this PVDF sample containing 3.5 mol % structural defects. Therefore, although the modulus and P_r of the TD increased slightly with annealing, the maximum values achieved by annealing were markedly lower than those of the SC and annealed SC. © 2003 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 41: 1701–1712, 2003     

Porous poly(vinylidene fluoride) membrane modified with hyperbranched poly(amine‐ester)

Poly(vinylidene fluoride) (PVDF) membranes were hydrophilic modified with hydroxyl group terminated hyperbranched poly(amine‐ester) (HPAE). Fourier transform infrared spectroscopy (FT‐IR) was used to study the chemical change of PVDF membranes. X‐ray photoelectron spectroscopy (XPS) indicated that some HPAE molecules were retained in PVDF membrane through polymer chain coiling. The presence of HPAE would improve the hydrophilicity of PVDF membrane. Scanning electron microscopy (SEM) was employed to characterize the morphology of different membranes. The thermodynamic stability for PVDF/DMAc/HPAE/Water system was characterized by the determination of the gelation values. Precipitation kinetics for PVDF/DMAc/HPAE/Water system was studied by precipitation time measurement. The water contact angle indicated that the hydrophilicity and the biocompatibility corresponding to protein adsorption of PVDF membrane were improved significantly after blending with hydrophilic HPAE molecules. Copyright © 2011 John Wiley & Sons, Ltd.     

Miscibility and ferroelectric behavior in blends of poly(vinylidene fluoride/trifluoroethylene) and poly(vinyl acetate)

The blend system containing a poly(vinylidene fluoride/trifluoroethylene) [P(VDF/TrFE)] copolymer (68/32 mol %) and poly(vinyl acetate) (PVAc) was miscible from the results of differential scanning calorimetry (DSC) studies that exhibit the presence of a single, composition‐dependent glass transition temperature (T_g) and a strong melting point depression for the semicrystalline P(VDF/TrFE) component. However, differences between the DSC and dielectric measurements, which showed a separate P(VDF/TrFE) T_g peak, suggests that the P(VDF/TrFE)/PVAc blends are actually partially miscible. Because of the lower dielectric constant of PVAc and the reduced sample crystallinity caused by the addition of PVAc, both the dielectric constant and the remanent polarization of the copolymer blends decrease with increasing PVAc content. The presence of a small amount of PVAc stabilized the anomalous ferroelectric behavior of ice–water‐quenched P(VDF/TrFE), and the blend portrayed normal polarization reversal behavior after adding only 1 wt % PVAc. The piezoelectric response suggests small changes with an increasing number of poling cycles. It is believed that PVAc affects the D‐E hysteresis behavior at the interface between crystalline and amorphous phases, although much work remains to be done to confirm this hypothesis. © 2003 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 41: 927–935, 2003     

Metal Salt‐Induced Ferroelectric Crystalline Phase in Poly(vinylidene fluoride) Films

In this Communication, the effect of varying mass fractions (0–20 wt.‐%) of calcium chloride (CaCl₂) salt on the α‐ and β‐phase content of poly(vinylidene fluoride) (PVDF) as‐cast films were investigated. Spectral and X‐ray studies revealed the maximum ferroelectric β‐phase for the addition of 15 wt.‐% of CaCl₂ in PVDF compared to neat PVDF samples. The dense β‐phase dominant PVDF–CaCl₂ (15 wt.‐%) thick film used as a ferroelectric insulator in one‐capacitor (1C) type random access memory device exhibited a remnant polarization of 3.1 µC · cm², and is a good indication that the unoriented PVDF–CaCl₂ films can be used in electronic applications without further stretching process.

     

Composition distributions within poly(vinylidene fluoride) spherulites as grown in blends with poly(methyl methacrylate)

Upon crystalline solidification of one component in a homogeneously molten polymer blend, composition profiles develop outside (i.e., in the rest melt) and behind (i.e., within the spherulites) the crystal growth front. The present article is devoted to the detailed verification and the interpretation of these distributions and their temporal development inside growing spherulites. To this end, the energy dispersive X‐ray emission (EDX) of suitable elements has been recorded locally resolved in a scanning electron microscope and evaluated correspondingly. The investigations were performed at the melt homogeneous blend of poly(vinylidene fluoride) (PVDF) as crystallizing and poly(methyl methacrylate) (PMMA) as steadily amorphous component. If the spherulites are not volume filling, the mean PMMA content 〈?_PMMA〉 inside the PVDF spherulites is for all blends about 0.2 below the starting composition. ?_PMMA increases however slightly from the center of a spherulite to its border. That increase reflects the PMMA concentration in front of the spherulite surface, which increases likewise with time, and is clearly above the initial composition. There is at the spherulite surface, consequently, a remarkable jump in composition from the spherulite internal to its amorphous surroundings. It may amount up to 0.5. With volume filling spherulites, a slight variation of the composition from the center of a spherulite to its border is observed, too. This proves that also at these conditions composition profiles develop in the spherulite's surroundings. They remain however so weak that they do not inhibit crystallization even in its later stages. © 2005 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 44: 338–346, 2006     

Thermoreversible gelation of blend of poly(vinylidene fluoride) and poly(vinylidene fluoride-trifluoroethylene) in γ-butyrolactone solution

Thermoreversible gelation behavior of blend of poly(vinylidene fluoride) and poly(vinylidene fluoride-trifluoroethylene) in γ-butyrolactone solution was studied. Sol-gel transition temperature increased with the increase of polymer concentration, but was independent of the blend ratio of two polymers. An equation for gelation rate was derived, assuming that the gelation is a first-order reaction and that the gelation rate obeys an Arrhenius type. According to the equation, the growth index of gelation and supercooling temperature had a dominant effect on gelation rate. The growth index of gelation, which was calculated from the dependence of activation energy on the supercooling temperature in the isothermal gelation, varied with the blend ratio of two polymers. Growth index of gelation larger than 2 was obtained for the blend gels studied in this experiment. It may suggest that the multidimensional growth of gels occurs in such polymer blend solutions. X-ray diffraction and differential scanning calorimetry measurements showed existence of separate crystals due to each component of polymer in the blend gels. © 1996 John Wiley & Sons, Inc.     

Thermal and mechanical behavior of amorphous and semi-crystalline poly(vinylidene fluoride)/poly(methyl methacrylate) blends

Various PVDF/PMMA (poly(vinylidene fluoride)/poly(methyl methacrylate)) blends were selected for mechanical testing in compression. At low PVDF content (less than 50/50 w/w), the blends remain amorphous and PVDF and PMMA are fully miscible. In PVDF-richer blends, PVDF crystallizes in part, leading to a PMMA-enriched homogeneous amorphous phase. In this study, the degree of crystallinity was set at equilibrium by appropriate annealing of the samples before testing. Mechanical analysis was focused on the low deformation range, and especially on the yield region. Depending on the test temperature and blend composition, three types of response were identified, depending on whether plastic deformation is influenced: 1) by the PMMA secondary relaxation motions, 2) by the PVDF/PMMA glass transition motions, or 3) by the crystallite-constrained PVDF chains.     

Synthesis of poly(vinylidene fluoride)‐b‐poly(styrene sulfonate) block copolymers by controlled radical polymerizations

Block copolymers based on poly(vinylidene fluoride), PVDF, and a series of poly(aromatic sulfonate) sequences were synthesized from controlled radical polymerizations (CRPs). According to the aromatic monomers, appropriate techniques of CRP were chosen: either iodine transfer polymerization (ITP) or atom transfer radical polymerization (ATRP) from PVDF‐I macromolecular chain transfer agents (CTAs) or PVDF‐CCl₃ macroinitiator, respectively. These precursors were produced either by ITP of VDF with C₆F₁₃I or by radical telomerization of VDF with chloroform, respectively. Poly(vinylidene fluoride)‐b‐poly(sodium styrene sulfonate), PVDF‐b‐PSSS, block copolymers were produced from both techniques via a direct polymerization of sodium styrene sulfonate (SSS) monomer or an indirect way with the use of styrene sulfonate ethyl ester (SSE) as a protected monomer. Although the reaction led to block copolymers, the kinetics of ITP of SSS showed that PVDF‐I macromolecular CTAs were not totally efficient because a limitation of the CTA consumption (56%) was observed. This was probably explained by both the low activity of the CTA (that contained inefficient PVDF‐CF₂CH₂? I) and a fast propagation rate of the monomer. That behavior was also noted in the ITP of SSE. On the other hand, ATRP of SSS initiated by PVDF‐CCl₃ was more controlled up to 50% of conversion leading to PVDF‐b‐PSSS block copolymer with an average number molar mass of 6000 g·mol^?1. © 2011 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2011     

Quantitative confirmation of the crystal-amorphous interphase in semicrystalline poly(vinylidene fluoride) and poly (vinylidene fluoride)/poly (ethyl methacrylate) blends

Dielectric and thermal characterizations were performed for poly (vinylidene fluoride) (PVDF)/poly (ethyl methacrylate) (PEMA) blends of different composition. The characteristics of PVDF β relaxation were shown to be little affected in the semicrystalline blends with PEMA. The relaxation strength, however, depends strongly on the PEMA content and a linear relation was found between the intensity of the β relaxation and the weight fraction of the PVDF crystal-amorphous interphase. Phase structures of the PVDF/PEMA blends are also proposed. © 1994 John Wiley & Sons, Inc.     

Controlled crystallization of poly(vinylidene fluoride) chains from mixed solvents composed of its good solvent and nonsolvent

Poly(vinylidene fluoride) (PVDF) chains with the same expanded state were obtained by dissolving PVDF resin in good solvent. Then, the crystallization of PVDF chains from mixed solvents composed of its good solvent and nonsolvent was investigated. N,N‐dimethylformamide (DMF) and ethanol were used as good solvent and nonsolvent of PVDF, respectively. The crystalline phases of PVDF were characterized by Fourier transform infrared (FTIR) spectroscopy and wide angle X‐ray diffraction (WAXD). For the crystallization of PVDF chains from mixed solvents, low ethanol content favored the formation of β phase, while high ethanol content resulted predominantly in the α phase. Different crystallization morphology was observed from the scanning electron microscopy (SEM) images. The obvious spherulite morphology disappeared with the increase in ethanol content in mixed solvent. According to thermal analyses, the crystallized PVDF from mixed solvents with high ethanol content had lower onset melting temperatures than that from low ethanol content. Smaller lamellar thickness calculated from WAXD data reasoned the low onset melting temperatures. The above results indicated that the crystallization of PVDF chains from mixed solvent was a “controlled” process by ethanol content. © 2010 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 48: 575–581, 2010     

Morphology,crystalline structure,and properties of poly(vinylidene fluoride)/silica hybrid composites

Poly(vinylidene fluoride)/silica (PVDF/SiO₂) hybrid composite films were prepared via sol–gel reactions from mixtures of PVDF and tetraethoxysilane in dimethylacetamide. Their morphology, crystalline structure, and thermal, mechanical, and electrical properties were examined. For morphology measurements, scanning electron microscopy and optical microscopy were applied. X‐ray diffraction and infrared analyses showed that the crystalline structure of PVDF was not changed much by the addition of SiO₂, indicating that there was no interaction between PVDF and SiO₂. With increasing SiO₂ content, the melting temperature rarely changed, the degree of crystallinity and the dielectric constant decreased, and the decomposition temperature slightly increased. A PVDF/SiO₂ hybrid composite film with 5 wt % SiO₂ exhibited balanced mechanical properties without a severe change in the crystalline structure of PVDF, whereas for the hybrid composites with higher SiO₂ contents (>10 wt %), the mechanical properties were reduced, and the spherulite texture of PVDF was significantly disrupted by the presence of SiO₂ particles. © 2001 John Wiley & Sons, Inc. J Polym Sci Part B: Polym Phys 40: 19–30, 2002     

Low contents of graphite improving general properties of poly(vinylidene fluoride)

Studies on graphite flakes with a lateral size greater than 50 μm, having a large number of stacked collapse blocks, are neglected and replaced by graphene nanosheets or by powdered graphite, which can be obtained from graphite through chemical or physical exfoliation, as filler in polymer composites. Besides, the production of graphene nanosheets or the purification of powdered graphite uses a high concentration of strong and toxic acids that pollutes the environment. These processes are extremely time-consuming and generate an expensive product. Composites of poly(vinylidene fluoride) (PVDF) were prepared via extrusion with graphite flakes with up to 60 μm thick and 700 μm lateral size, in the range from 0.1 to 5% m/m. The quality of graphite flakes was analyzed by thermogravimetric analysis, x-ray diffraction (XRD), Raman spectroscopy, Fourier-transform infrared spectroscopy, and scanning electron microscopy. The increase in the graphite content in the PVDF matrix improved thermal resistance while showed an increase in the degree of crystallinity up to 25% by XRD and 43% by differential scanning calorimetry, approximately. Although the graphite acted as a nucleating agent, the content of the PVDF beta phase did not change. In the composites with up to 2.0% of graphite, a significant increase in mechanical properties, 13% modulus, and 36% in the storage modulus, evaluated by thermodynamic-mechanical analysis and tensile tests. In the analyses of time-domain nuclear magnetic resonance and oscillatory rheology in parallel plates, it was noticed that the increase of mechanical properties is due to the reinforcing effect along with the lubricant protection of stacked graphene sheets, attenuating the stress and friction between the polymer chains. Therefore, even though graphite flakes are inexpensive, that filler without any treatment at low contents are capable of significantly improving the performance of PVDF. This work suggests that these composites could be employed in applications such as electrical insulator with less energy dissipation, and also in oil pipelines, specifically to replace PVDF-based terpolymers or mixtures thereof, and polyamide-11 in flexible risers as a barrier layer, improving their performance.     

Fracture behavior of amorphous and semicrystalline blends of poly(vinylidene fluoride) and poly(methyl methacrylate)

The fracture behavior of blends of poly(vinylidene fluoride) and poly(methyl methacrylate) was investigated all over the composition range. A detailed analysis of the net stress versus crack opening displacement curves was performed. Fracture surface observations allowed statements on the process zone characteristics ahead of the crack tip. For the amorphous blends, the crack initiation energy is well related to the glass transition temperature. For the semicrystalline blends, the fracture energy is correlated with the degree of crystallinity. © 2012 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys, 2012