Functionalization of polyisobutylene and polyisobutylene oligomers via the ritter reaction

The Ritter reaction, that is, reaction of a carbocation with a nitrile, was carried out on polyisobutylene (PIB) using a variety of reaction conditions. End quenching of PIB carbocations with acrylonitrile under living polymerization conditions (methyl chloride (MeCl)/hexane 60/40 (v/v) solvent mixtures at −70 °C) resulted in either tert‐chloride end groups or loss of chain‐end fidelity via carbocation rearrangement, as evidenced by NMR spectroscopy. Exo‐olefin functionalized PIB substrates were also reacted with nitriles under a variety of reaction conditions including various acid and solvent medium combinations. In all cases, the result was either no reaction or PIB that had undergone severe backbone degradation, as determined via NMR spectroscopy and gel permeation chromatography. Finally, the Ritter reaction was performed on a series of exo‐olefin functionalized oligoisobutylenes using acrylonitrile as the nitrile and either 60/40 dichloromethane/hexane or excess acrylonitrile as the solvent. In 60/40 dichloromethane/hexane, significant carbocation rearrangement and/or degradation resulted in a variety of isomeric, acrylamide‐functionalized oligomers. In excess acrylonitrile, the desired Ritter reaction was the only reaction observed, resulting in the smooth formation of the terminal acrylamide. The various N‐oligoisobutylacrylamides thus obtained represent new hydrophobic monomers useful for the introduction of hydrophobic moieties into acrylamide‐based water‐soluble polymers. © 2018 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2018 , 56, 840–852     

Synthesis and radical polymerization properties of thermal radical initiators based on o‐imino‐isourea: The effect of the alkyl side chain on the radical initiation temperature

Four types of thermal radical initiators (TRIs) that are based on o‐imino‐isourea with cyclohexyl and isopropyl groups were successfully synthesized, namely, C‐HexDCC, DiiprDCC, C‐HexDIC, and DiiprDIC. The free radical polymerization and thermal properties of those synthesized TRIs were determined via differential scanning calorimetry (DSC) (using n‐butyl acrylate) and thermogravimetric analysis (TGA), respectively. The TRI derivatives showed peak temperatures (T_max) from 89 to 97 °C in n‐butyl acrylate, and DiiprDIC, with isopropyl groups on both sides of the N O group, showed the lowest peak temperatures. The rates of N O bond homolysis (k_d) of all the TRIs were calculated from their half‐lives determined using real‐time nuclear magnetic resonance (NMR) spectroscopy, and their theoretical bond dissociation energies (BDEs) were calculated using density functional theory (DFT) calculations. The free radical polymerization of n‐butyl acrylate using each TRI was efficiently determined from T_peak of the DSC curves; conversions depending on polymerization temperature (80, 90, and 100 °C) were monitored to observe kinetic information of TRIs during polymerization. Furthermore, to investigate the use of TRIs in curing, we applied them to an automotive clear coating system and monitored the real‐time evolution of the elastic modulus (G′) during thermal curing using a rheometer for representative DiiprDIC. © 2018 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2018 , 56, 1749–1756     

N‐alkoxy pyridinium ion terminated polystyrenes: A facile route to photoinduced block copolymerization

Photoactive N‐alkoxy 4‐phenyl pyridinium and N‐alkoxy isoquinolinium ion terminated polystyrenes with hexafluoroantimonate counter anion were prepared and characterized. For this purpose, mono‐ and dibrominated polystyrenes were prepared by atom transfer radical polymerization (ATRP). The reaction of these polymers with silver hexafluoroantimonate in the presence of 4‐phenylpyridine N‐oxide and isoquinoline N‐oxide in dichloromethane produced desired polymeric salts with the corresponding functionalities. Irradiation of these photoactive polystyrenes produced alkoxy radicals at chain ends capable of initiating free radical polymerization of methyl methacrylate (MMA). This way, depending on the number of functionality, AB or ABA type block copolymers were formed which were characterized with the aid of gel permeation chromatography and ¹H NMR spectroscopy. © 2006 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 45: 423–428, 2007.     

Synthesis of n‐alkyl methacrylate polymers with pendant carbazole moieties and their derivatives

New methacrylate monomers with carbazole moieties as pendant groups were synthesized by multistep syntheses starting from carbazoles with biphenyl substituents in the aromatic ring. The corresponding polymers were prepared using a free‐radical polymerization. The novel polymers contain N‐alkylated carbazoles mono‐ or bi‐substituted with biphenyl groups in the aromatic ring. N‐alkyl chains in polymers vary by length and structure. All new polymers were synthesized to evaluate the structural changes in terms of their effect on the energy profile, thermal, dielectric, and photophysical properties when compared to the parent polymer poly(2‐(9H‐carbazol‐9‐yl)ethyl methacrylate). According to the obtained results, these compounds may be well suited for memory resistor devices. © 2018 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2019 , 57, 70–76     

Surface study of ladderlike polyepoxysiloxanes

By using the two‐liquid geometric method and the three‐liquid acid‐base method, we are the first to determine the surface tensions of ladderlike polyepoxysiloxanes by the measurement of contact angles on thin films. Three kinds of ladderlike polymers have been synthesized: A C (which has the alkyl group and the epoxy group graft to the ladderlike polysilsesquioxane chain), A C P (which has the alkyl group, phenyl group, and epoxy group graft to the ladderlike chain), and A P (which has the phenyl group and epoxy group in the ladderlike side chain). The results showed that when different liquids and different theories are chosen to determine the surface energies, there are some minor differences in the values but a similar trend is still exhibited. The surface energies of these three polymers are in the following order of γ_{SA C} < γ_{SA C P} < γ_{SA P}. Interestingly, the surface energy increases for these polymers are mainly from the nonpolar part of the polyepoxysiloxanes. XPS surface analysis indicated that the Si and O ratios of these polymers at the air‐polymer interface were in the order of A C > A C P > A P, suggesting Si atoms were more likely to migrate to the polymer surface and the bulky effect of the phenyl groups could also interfere with the migration of the Si atoms. As a result, Si and O ratio at the interface determines the order of apparent surface energy for these three polymers. Experimental data also reflect that there are differences between the ladderlike polyepoxysiloxanes and the commercially available linear polysiloxanes. © 2000 John Wiley & Sons, Inc. J Polym Sci B: Polym Phys 38: 138–147, 2000     

Study on thermal degradation mechanisms of comb polyacrylates containing long fluorocarbon side chains by TG/FTIR

Thermal degradation of two series of polyacrylates containing long fluorocarbon chains [abbr.: PF_nA {HCF₂(CF₂)_n−1  CH₂ O C(O) , n = 4, 6, 8, 10} and abbr.: PFF_nEA {CF₃(CF₂)_n−1  CH₂CH₂ O C(O) , n = 6, 8, 10}] was investigated by TG /FTIR. Thermal degradation behavior of polymers changed depending on the type of tie groups, which link the fluorocarbon chains to the main chain, and also on the length of fluorocarbon chains. It was clarified that the apparent activation energies (ΔE_a ) of PF_nA series obtained by Ozawa's method varied in the order of PF₄A > PF₆A > PF₈A > PF₁₀A, while those of PFF_nEA series having tie group of  CH₂ CH₂ O C(O) were almost constant. The results for PF_nA series (tie group:  CH₂ O C(O) ) are attributable to the shield effect of long fluorocarbon chains on the back‐biting reaction in the thermal degradation of comb polymers rather than the change of C C bond dissociation energy in the main chain. It was found that TG curves of PFF_nEA series were shifted to the lower temperature region than those of PF_nA. This result can be attributable to the scission of side groups followed by the evaporation of fluorocarbon compounds and carbon dioxide. © 2000 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 38: 2794–2803, 2000     

Facile synthesis of functional polyperoxides by radical alternating copolymerization of 1,3‐dienes with oxygen

We have developed a facile synthesis of degradable polyperoxides by the radical alternating copolymerization of 1,3‐diene monomers with molecular oxygen at an atmospheric pressure. In this review, the synthesis, the degradation behavior, and the applications of functional polyperoxides are summarized. The alkyl sorbates as the conjugated 1,3‐dienes gave a regiospecific alternating copolymer by exclusive 5,4‐addition during polymerization and the resulting polyperoxides decomposed by the homolysis of a peroxy linkage followed by successive β‐scissions. The preference of 5,4‐addition was well rationalized by theoretical calculations. The degradation of the polyperoxides occurred with various stimuli, such as heating, UV irradiation, a redox reaction with amines, and an enzyme reaction. The various functional polyperoxides were synthesized by following two methods, one is the direct copolymerization of functional 1,3‐dienes, and the other is the functionalization of the precursor polyperoxides. Water soluble polyperoxides were also prepared, and the LCST behavior and the application to a drug carrier in the drug delivery system were investigated. In order to design various types of degradable polymers and gels we developed a method for the introduction of dienyl groups into the precursor polymers. The resulting dienyl‐functionalized polymers were used for the degradable gels. The degradable branched copolymers showed a microphase‐separated structure, which changed owing to the degradation of the polyperoxide segments. © 2009 The Japan Chemical Journal Forum and Wiley Periodicals, Inc. Chem Rec 9: 000–000; 2009: Published online in Wiley InterScience ( www.interscience.wiley.com ) DOI 10.1002/tcr.200900009     

Molecular design of outermost surface functionalized thermoresponsive polymeric micelles with biodegradable cores

We prepared well‐defined diblock copolymers of thermoresponsive poly(N‐isopropylacrylamide‐co‐N,N‐dimethylacrylamide) blocks and biodegradable poly(D ,L ‐lactide) blocks by combination of reversible addition‐fragmentation chain transfer radical (RAFT) polymerization and ring‐opening polymerization. α‐Hydroxyl, ω‐dithiobenzoate thermoresponsive polymers were synthesized by RAFT polymerization using hydroxyl RAFT agents. Biodegradable blocks were prepared by ring‐opening polymerization of D ,L ‐lactide initiated by α‐hydroxyl groups of thermoresponsive polymers, which inhibit the thermal decomposition of ω‐dithioester groups. Terminal dithiobenzoate (DTBz) groups of thermoresponsive blocks were easily reduced to thiol groups and reacted with maleimide (Mal). In aqueous media, diblock copolymer products formed surface‐functionalized thermoresponsive micelles. These polymeric micelles had a low critical micelle concentration of 22 μg/L. In thermoresponsive studies of the micelles, hydrophobic DTBz‐surface micelles demonstrated a significant shift in lower critical solution temperature (LCST) to a lower temperature of 30.7 °C than that for Mal‐surface micelles (40.0 °C). In addition, micellar LCST was controlled by changing bulk mixture ratios of respective heterogeneous end‐functional diblock copolymers. Micellar disruption at acidic condition (pH 5.0) was completed within 5 days due to hydrolytic degradation of PLA cores, regardless of showing a slow disruption rate at physiological condition. Furthermore, we successfully improved water‐solubility of hydrophobic drug, paclitaxel by incorporating into the micellar cores. © Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 46: 7127–7137, 2008     

Star polymers by cross‐linking of linear poly(benzyl‐L‐glutamate) macromonomers via free‐radical and RAFT polymerization. A simple route toward peptide‐stabilized nanoparticles

Poly(benzyl‐L ‐glutamate) (PBLG) macromonomers were synthesized by N‐carboxyanhydride (NCA) polymerization initiated with 4‐vinyl benzylamine. MALDI‐ToF analysis confirmed the presence of styrenic end‐groups in the PBLG. Free‐radical and RAFT polymerization of the macromonomer in the presence of divinyl benzene produced star polymers of various molecular weights, polydispersity, and yield depending on the reaction conditions applied. The highest molecular weight (M_w) of 10,170,000 g/mol was obtained in a free‐radical multibatch approach. It was shown that the PBLG star polymers can be deprotected to obtain poly(glutamic acid) star polymers, which form water soluble pH responsive nanoparticles. © 2010 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2010     

Reversible addition‐fragmentation chain transfer polymerization of methacrylates containing hole‐ or electron‐transporting groups

The controlled/living radical polymerization of 2‐(N‐carbazolyl)ethyl methacrylate (CzEMA) and 4‐(5‐(4‐tert‐butylphenyl‐1,3,4‐oxadiazol‐2‐yl)phenyl) methacrylate (t‐Bu‐OxaMA) via reversible addition‐fragmentation chain transfer polymerization has been studied. Functional polymers with hole‐ or electron‐transfer ability were synthesized with cumyl dithiobenzoate as a chain transfer agent (CTA) and AIBN as an initiator in a benzene solution. Good control of the polymerization was confirmed by the linear increase in the molecular weight (MW) with the conversion. The dependence of MW and polydispersity index (PDI) of the resulting polymers on the molar ratio of monomer to CTA, monomer concentration, and molar ratio of CTA to initiator has also been investigated. The MW and PDI of the resulting polymers were well controlled as being revealed by GPC measurements. The resulting polymers were further characterized by NMR, UV‐vis spectroscopy, and cyclic voltammetry. The polymers functionalized with carbazole group or 1,3,4‐oxadiazole group exhibited good thermal stability, with an onset decomposition temperature of about 305 and 323 °C, respectively, as determined by thermogravimetric analysis. © 2006 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 45: 242–252, 2007     

Preparation of poly(alkylenebenzimidazole) by ruthenium complex catalyzed polycondensation of 3,3′‐diaminobenzidine with α,ω‐diols

The reactions of 3,3′‐diaminobenzidine with 1,12‐dodecanediol in 1 : 1–1:3 molar ratios in the presence of RuCl₂(PPh₃)₃ catalyst give poly(alkylenebenzimidazole), [ (CH₂)₁₁ O (CH₂)₁₁ Im / (CH₂)₁₀ Im ]_n (Im: 5,5′‐dibenzimidazole‐2,2′‐diyl) (I_a‐I_d) in 71–92% yields. The relative ratio between the [(CH₂)₁₁ O (CH₂)₁₁ Im ] unit (A) and the [‐ (CH₂)₁₀ Im ] unit (B) in the polymer chain varies depending on the ratio of the substrates used. The polymer I_a obtained from the 1 : 3 reaction contains these structural units in a 98 : 2 ratio. The polymers are soluble in polar solvents such as DMF (N,N‐dimethylformamide), DMSO (dimethyl sulfoxide), and NMP (N‐methyl‐2‐pyrrolidone) and have molecular weights M_n (M_w) of 4,200–4,800 (4,800–6,500) by GPC (polystyrene standard). The polymerization of the diol and 3,3′‐diaminobenzidine in higher molar ratios leads to partial cross‐linking of the resulting polymers I_e and I_f via condensation of imidazole NH group with CH₂OH group. Similar reactions of 3,3′‐diaminobenzidine with α,ω‐diols, HO(CH₂)_mOH (m = 4–10), in a 1 : 3 molar ratio give the polymers containing [ (CH₂)_m−1 O (CH₂) _m−1 Im ] and [ (CH₂) _m−2 Im ] units with partial cross‐linked structures. © 1999 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 37: 1383–1392, 1999     

Limitations of cyclodextrin‐mediated RAFT homopolymerization and block copolymer formation

The design and synthesis of a new hydrophobic monomer, that is, 4‐(tert‐butyl)phenyl 6‐acrylamidohexanoate (TBP‐AA‐HO) and its ability to form supramolecular host/guest complexes with β‐cyclodextrin (CD) is described. The aqueous CD‐mediated reversible addition fragmentation chain transfer (RAFT) polymerization affords molecular masses up to 8600 g mol^?1 with polydispersities between 1.2 and 1.4. The surprisingly low molecular weights for higher monomer/chain transfer agent (CTA) ratios are investigated by comparing results obtained from free radical and RAFT radical polymerization in aqueous and organic media. The results indicate a steric hindrance caused by attached CD molecules on the growing polymer chain leading to stagnation of the polymerization process due to a restricted accessibility of the reactive chain end. This hypothesis is supported by matrix‐assisted laser desorption/ionization time of flight mass spectrometry. Furthermore, the CD‐mediated synthesis of amphiphilic diblock copolymers in variable aqueous media is described. Hydrophilic poly(N,N‐dimethylacrylamide) macro‐CTAs with different molecular weights are used to polymerize TBP‐AA‐HO at 50 °C. The diblock copolymers are analyzed by ¹H‐nuclear magnetic resonance spectroscopy and size exclusion chromatography. The results confirm the polymer structure and reveal similar limitations of chain growth as observed for the CD‐mediated homopolymerization with a limit of 7000 g mol^?1 for efficient chain extension. © 2013 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2013, 51, 2504–2517     

Synthesis of telechelic anthraquinone‐functionalized polybutadiene via ROMP and study of its photo‐oxidation and UV crosslinking behaviors

Telechelic anthraquinone‐functionalized polybutadiene (AQ‐PB‐AQ) was synthesized by ring opening metathesis polymerization to achieve homogeneous dispersion of AQ groups in the polymer matrix. It was observed that the AQ end groups act as a sensitizing group resulting in photo‐induced crosslinking and oxidation reaction at the olefin groups in the PB. The process was confirmed by comparing the polymer's mass loss and Fourier transform infrared (FTIR) spectra with those of telechelic diacetoxy‐functionalized PB (AcO‐PB‐OAc) which did not show any difference before and after ultraviolet irradiation. Homogeneity of the AQ groups in PB matrix results in rapid crosslinking of PB in a short period of time (<4 min) while a simple blend of AQ methyl ester in AcO‐PB‐OAc matrix did not show such behavior. Photo‐oxidative reaction has concurrently occurred during the crosslinking reaction. Generation of  OH,  OOH, and carbonyl groups in the matrix during the photo‐oxidation was verified by FTIR, elemental analysis, and water contact angle measurements. A plausible mechanism for the process was proposed in which the photo‐sensitized AQ groups abstract hydrogen from the PB chain to yield reactive radical species, initiating oxidative crosslinking, and degradation of PB or reduction of AQ to hydroanthraquinone species. © 2018 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2018 , 56, 1249–1258     

Synthesis and characterization of multifunctional polymers via atom transfer radical polymerization of N‐(ω′‐alkylcarbazolyl) methacrylates initiated by Ru(II) polypyridyl chromophores

A series of poly(N‐(ω′‐alkylcarbazoly) methacrylates) tris(bipyridine) Ru‐centered bifunctional polymers with good filming, thermal, and solubility properties were synthesized and characterized. Atom transfer radical polymerization (ATRP) of N‐(ω′‐alkylcarbazoly) methacrylates in solution was used, where Ru complexes with one and three initiating sites acted as metalloinitiators with NiBr₂(PPh₃)₂ as a catalyst. ATRP reaction conditions with respect to polymer molecular weights and polydispersity indices (PDI) of the target bifunctional polymers were examined. Electronic absorption and emission spectra of the resultant functional polymers provided evidence of chromophore presence within a single polymeric chain. The thermal properties of all polymers were also investigated by differential scanning calorimetry (DSC) and thermogravimetric analysis (TGA), and these analyses have indicated that these polymers possess higher thermal stabilities than poly(methyl methacrylate) (PMMA) obtained via free radical polymerization. © 2005 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 43: 6057–6072, 2005     

Orthogonally functionalizable copolymers based on a novel reactive carbonate monomer

A novel N‐hydroxy succinimide‐based carbonate monomer that allows direct synthesis of polymers incorporating a reactive carbonate group in the side chain was synthesized. This new monomer was copolymerized with methyl methacrylate and poly(ethylene glycol) methylether methacrylate using free‐radical polymerization to obtain organo‐ and water‐soluble reactive copolymers. Copolymerization of the activated carbonate monomer with an azide‐containing monomer and N‐hydroxy succinimide‐containing activated ester monomer provided orthogonally functionalizable copolymers. The pendant reactive carbonate groups of the copolymers were functionalized with amines to obtain carbamates. Polymers capable of orthogonal functionalization could be selectively functionalized as desired using subsequent 1,3‐dipolar cycloaddition or amidation reactions. The novel monomer and the copolymers were characterized by ¹H‐NMR, ¹³C‐NMR, and infrared spectroscopy. The efficient stepwise orthogonal functionalization of the copolymers were examined via ¹H‐NMR spectroscopy. © 2010 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2010     

Air‐tolerantly surface‐initiated AGET ATRP mediated by iron catalyst from silica nanoparticles

Well‐defined polymer‐nanoparticle hybrids were prepared by a newly reported method: atom transfer radical polymerization using activators generated by electron transfer (AGET ATRP) mediated by iron catalyst. The kinetics of the surface‐initiated AGET ATRP of methyl methacrylate from the silica nanoparticles, which was mediated by FeCl₃/triphenylphosphine as a catalyst complex, ascorbic acid as a reducing agent, N,N‐dimethylformamide as the solvent in the presence of a “sacrificial” (free) initiator, was studied. Both the free and grafted polymers were grown in a control manner. The chemical composition of the nanocomposites was characterized by Fourier transform infrared spectroscopy, X‐ray photoelectron spectroscopy, and ¹H nuclear magnetic resonance spectroscopy. Thermogravimetric analysis was used to estimate the content of the grafted organic compound, and transmission electron micrographs was used to observe the core‐shell structure of the hybrid nanoparticles. © 2010 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 48: 2006–2015, 2010     

Thermal‐initiating potentialities of vinyl polyperoxides: Transmutation of block‐into‐block copolymer and an exploratory investigation of surface texture and morphology

This article describes the first comprehensive study on the use of vinyl polyperoxides, namely, poly(α‐methyl styrene peroxide) (PMSP) and poly(styrene peroxide) (PSP), as thermal initiators for the synthesis of active polymers, PMSP–PS–PMSP/PSP–PS–PSP, by free‐radical polymerization with styrene. The active polymers have been characterized by ¹H NMR, differential scanning calorimetry, thermogravimetric analysis, and gel permeation chromatography analysis. The PMSP–PS–PMSP/PSP–PS–PSP is further used as the thermal macroinitiator for the preparation of another block copolymer, PS‐b‐PMMA, through the reaction of the active polymers with methyl methacrylate. The mechanism of the block copolymer formation is discussed. Having established the scanning micrograph details of the homopolymer phases, we analyze the surface features and morphology of the block copolymer. Furthermore, the distinction in appearance is highlighted with a view toward strengthening the chemistry with the structural appearance in materials processed differently. © 2000 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 38: 3665–3673, 2000     

Alternating polyester/fluoroalkene copolymers: Combining high hydrophobicity with degradability

2‐Methylene‐1,3‐dioxepane (MDO) was copolymerized with fluoroalkenes (R_fCH?CH₂) using azobis(isobutyronitrile) AIBN as an initiator. NMR spectroscopy confirmed that the obtained polymers are effectively alternating copolymers of caprolactone and fluoroalkene. Angle resolved XPS of copolymer films revealed that the outer layers have higher CF_x:COO ratio relative to the subsurface, indicating that the perfluoroalkyl tails segregate to the air‐side, thereby presenting a hydrophobic surface with water contact angle as high as 130°. Blends of this material with polycaprolactone and polycarbonate polymers also form hydrophobic films. In the presence of trifluoroacetic acid, the copolymer undergoes complete degradation through hydrolysis. © 2005 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 44: 1225–1232, 2006     

A simple FTIR spectroscopic method for the determination of the lower critical solution temperature of N‐isopropylacrylamide copolymers and related hydrogels

Linear and crosslinked polymers based on N‐isopropylacrylamide (NIPAAm) exhibit unusual thermal properties. Aqueous solutions of poly(N‐isopropylacrylamide) (PNIPAAm) phase‐separate upon heating above a lower critical solution temperature (LCST), whereas related hydrogels undergo a swelling–shrinking transition at an LCST. A linear copolymer made of NIPAAm/acryloxysuccinimide (98/2 mol/mol) and two hydrogels with different hydrophilicities were prepared. Fourier transform infrared (FTIR) spectroscopy was employed to determine the transition temperature and provide insights into the molecular details of the transition via probing of characteristic bands as a function of temperature. The FTIR spectroscopy method described here allowed the determination of the transition temperature for both the linear and crosslinked polymers. The transition temperatures for PNIPAAm and the gel resulting from the crosslinking with polylysine or N,N′‐methylenebisacrylamide (MBA) were in the same range, 30–35 °C. For the gels, the transition temperature increased with the hydrophilicity of the polymer matrix. The spectral changes observed at the LCST were similar for the free chains and the hydrogels, implying a similar molecular reorganization during the transition. The C H stretching region suggests that the N‐isopropyl groups and the backbone both underwent conformational changes and became more ordered upon heating above the LCST. An analysis of the amide I band suggests that the amide groups of the linear polymer were mainly involved in hydrogen bonding with water molecules below the LCST, the chain being flexible and disordered in a water solution. During the transition, around 20% of these intermolecular hydrogen bonds between the polymer and water were broken and replaced by intramolecular hydrogen bonds. Similar changes were also observed at the LCST of a gel crosslinked with MBA. © 2000 John Wiley & Sons, Inc. J Polym Sci B: Polym Phys 38: 907–915, 2000     

R‐RAFT approach for the polymerization of N‐isopropylacrylamide with a star poly(ε‐caprolactone) core

Reversible addition‐fragmentation chain transfer (RAFT) polymerization is a more robust and versatile approach than other living free radical polymerization methods, providing a reactive thiocarbonylthio end group. A series of well‐defined star diblock [poly(ε‐caprolactone)‐b‐poly(N‐isopropylacrylamide)]₄ (SPCLNIP) copolymers were synthesized by R‐RAFT polymerization of N‐isopropylacrylamide (NIPAAm) using [PCL‐DDAT]₄ (SPCL‐DDAT) as a star macro‐RAFT agent (DDAT: S‐1‐dodecyl‐S′‐(α, α′‐dimethyl‐α″‐acetic acid) trithiocarbonate). The R‐RAFT polymerization showed a controlled/“living” character, proceeding with pseudo‐first‐order kinetics. All these star polymers with different molecular weights exhibited narrow molecular weight distributions of less than 1.2. The effect of polymerization temperature and molecular weight of the star macro‐RAFT agent on the polymerization kinetics of NIPAAm monomers was also addressed. Hardly any radical–radical coupling by‐products were detected, while linear side products were kept to a minimum by careful control over polymerization conditions. The trithiocarbonate groups were transferred to polymer chain ends by R‐RAFT polymerization, providing potential possibility of further modification by thiocarbonylthio chemistry. © 2011 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2011