D‐π‐a‐type oxime sulfonate photoacid generators for cationic polymerization under UV–visible LED irradiation

Four D‐π‐A‐type nonionic oxime sulfonate photoacid generators (PAGs) have been designed and synthesized for use in light‐emitting diode (LED) excitable cationic photoinitiators, in which N,N‐diphenylamino was used as electron donor with trifluoroacetophenone‐based oxime sulfonates (trifluoromethanoesulfonate and p‐toluenesulfonate) as electron acceptor and substituted fluorene and biphenyl groups as the π‐conjugated systems. PAG‐Ben‐Tol (with biphenyl and p‐toluenesulfonate) and PAG‐Flu‐Tol (with fluorene and p‐toluenesulfonate) showed high quantum yields of photoacid generation (0.33–0.50) and very good thermal stability (over 250 °C). The absorbance spectra of these PAGs were consistent with the emission spectra of commercially gained UV–visible LED light sources. The potential of these PAGs for cationic photoinitiators was tested in two cationic monomer systems. These PAGs needed low light intensity and low concentration for photopolymerization with high conversions of monomer, for example, over 80%, gained at 3.0 mW cm⁻² from 365 to 470 nm LEDs. The photochemical mechanisms of these PAGs are comprehensively investigated and discussed in detail. © 2018 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2018 , 56, 1146–1154     

2,2,2‐trifluoroacetophenone‐based D‐π‐A type photoinitiators for radical and cationic photopolymerizations under near‐UV and visible LEDs

Two D‐π‐A‐type 2,2,2‐trifluoroacetophenone derivatives, namely, 4′‐(4‐( N,N‐diphenyl)amino‐phenyl)‐phenyl‐2,2,2‐trifluoroacetophenone (PI‐Ben) and 4′‐(4‐(7‐(N,N‐diphenylamino)‐9,9‐dimethyl‐9H‐fluoren‐2‐yl)‐phenyl‐2,2,2‐trifluoroacetophenone (PI‐Flu), are developed as high‐performance photoinitiators combined with an amine or an iodonium salt for both the free‐radical polymerization of acrylates and the cationic polymerization of epoxides and vinyl ether upon exposure to near‐UV and visible light‐emitting diodes (LEDs; e.g., 365, 385, 405, and 450 nm). The photochemical mechanisms are investigated by UV‐Vis spectra, molecular‐orbital calculations, fluorescence, cyclic voltammetry, photolysis, and electron‐spin‐resonance spin‐trapping techniques. Compared with 2,2,2‐trifluoroacetophenone, both photoinitiators exhibit larger redshift of the absorption spectra and higher molar‐extinction coefficients. PI‐Ben and PI‐Flu themselves can produce free radicals to initiate the polymerization of acrylate without any added hydrogen donor. These novel D‐π‐A type trifluoroacetophenone‐based photoinitiating systems exhibit good efficiencies (acrylate conversion = 48%–66%; epoxide conversion = 85%–95%; LEDs at 365–450 nm exposure) even in low‐concentration initiators (0.5%, w/w) and very low curing light intensities (1–2 mW cm^?2). © 2016 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2016 , 54, 1945–1954     

Dual roles for promoting monomers to polymers: A conjugated sulfonium salt photoacid generator as photoinitiator and photosensitizer in cationic photopolymerization

An efficient strategy for comprehensive utilization of the conjugated sulfonium salt photoacid generator (PAG), namely, 3‐{4‐[4‐(4‐N,N′‐diphenylamino)‐styryl]phenyl}phenyl dimethyl sulfonium hexafluoroantimonate, was developed through photoinitiated cationic photopolymerization (CP) of epoxides and vinyl ether upon exposure to near‐UV and visible light‐emitting diodes (LEDs; e.g., 365, 385, 405, and 425 nm). Photochemical mechanisms were investigated by UV–vis spectra, molecular orbital calculations, fluorescence, cyclic voltammetry, and electron spin resonance spin‐trapping analyses. Compared with commercial PAGs, the prepared conjugated sulfonium salt generated H⁺, which can be used as photoinitiator. Moreover, the fluorescent byproducts from photodecomposition can be used as photosensitizer of commercial iodonium salt in the photoinitiating systems of CP. These novel D‐π‐A type sulfonium‐based photoinitiating systems are efficient (epoxide conversion = 85–90% and vinyl conversion >90%; LEDs upon exposure to 365–425 nm) even in low‐concentration initiators (1%, w/w) and low curing light intensities (10–40 mW cm^?2). © 2016 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2016 , 54, 2722–2730     

Synthesis of dual‐functional copolymer with orthogonally photosensitive groups

A dual‐functional copolymer, poly(4‐styrenesulfonyl azide‐co‐t‐butyl‐methacrylate), with built‐in photoacid labile and photocrosslinkable components was designed and synthesized by radical copolymerization. The mixture of copolymer and photoacid generators was spin coated on aminosilane treated Si wafers and polycarbonate (PC). When exposed to 365 nm UV light, photoacids were generated, which decomposed the acid labile groups, t‐butyl‐ester, to carboxylic acid in the exposed region, leading to drastic change of wettability from hydrophobic to hydrophilic after developing the film in an aqueous base solution. The patterned polymer film could be subsequently photoimmobilized on the substrate under 254 nm deep UV exposure through C? H insertion via exited azide groups. ¹H‐NMR and Fourier transform infrared spectra confirmed the synthesis of the copolymer, and the photodecomposition and photografting reactions occurred orthogonally at 365 and 254 nm, respectively, without interfering each other. On the patterned surfaces, including a hexagonal dot array and a gradient line array, we demonstrated selective wetting in the 365 nm exposed regions. On the gradient line array, we showed an interesting ratchet wetting pattern. Finally, we showed that the copolymer could be used to modify the wettability of PC while maintaining its high optical quality. © 2012 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2013     

Visible‐light‐sensitive photoredox catalysis by iron complexes: Applications in cationic and radical polymerization reactions

The development of iron complexes for the photoredox catalysis is a huge challenge. Indeed, Iron complexes can be ideal candidates due to their potential visible light absorption and redox properties but also because they are less toxic, inexpensive and environmentally friendly compared to other catalysts. In the present paper, a series of novel iron complexes have been synthesized and utilized to initiate the free radical promoted cationic polymerization of epoxides or the free radical polymerization of acrylates through photoredox catalysis processes upon exposure to near UV (385 nm) or visible violet (405 nm) light emitting diodes (LEDs). When combined with an iodonium salt and N‐vinylcarbazole, the iron complex‐based photoinitiating systems are able to generate radicals, cations, and radical cations. The initiation efficiency is investigated through real‐time Fourier transform infrared spectroscopy and a satisfactory initiating ability is found. The mechanisms for the generation of the reactive initiating species through photoredox catalysis are studied by different methods (steady state photolysis, cyclic voltammetry and electron spin resonance spin trapping techniques) and discussed in detail. © 2016 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2016 , 54, 2247–2253     

Development of 1‐Hydroxy‐2(1H)‐quinolone‐Based Photoacid Generators and Photoresponsive Polymer Surfaces

A new class of carboxylate and sulfonate esters of 1‐hydroxy‐2(1H)‐quinolone has been demonstrated as nonionic photoacid generators (PAGs). Irradiation of carboxylates and sulfonates of 1‐hydroxy‐2(1H)‐quinolone by UV light (λ≥310 nm) resulted in homolysis of weak N? O bond leading to efficient generation of carboxylic and sulfonic acids, respectively. The mechanism for the homolytic N? O bond cleavage was supported by time‐dependent DFT calculations. Photoresponsive 1‐(p‐styrenesulfonyloxy)‐2‐quinolone–methyl methacrylate (SSQL‐MMA) and 1‐(p‐styrenesulfonyloxy)‐2‐quinolone–lauryl acrylate (SSQL‐LA) copolymers were synthesized from PAG monomer 1‐(p‐styrenesulfonyloxy)‐2‐quinolone, and subsequently controlled surface wettability was demonstrated for the above‐mentioned photoresponsive polymers.     

Degradable alternating polyperoxides from poly(ethylene glycol)‐substituted styrenic monomers with water solubility and thermoresponsiveness

Water soluble alternating copolymers were prepared by oxidative free radical copolymerization of 4‐vinylbenzyl methoxypoly(oxyethylene) ether (PEGSt) and molecular oxygen at 50 °C. NMR spectroscopy established alternate sequence of PEGSt and peroxy bonds ( O O ) along the polymer main‐chain. The obtained polymers show temperature induced hydrophilic to hydrophobic phase separation, confirmed by UV‐visible spectroscopy and dynamic light scattering. The cloud point temperature (T_CP) of the polymers can be tuned by changing the chain length of side‐chain poly(ethylene oxide) and incorporation of hydrophobic methyl methacrylate in the copolyperoxides. Exothermic degradation of these polyperoxides was confirmed by differential scanning calorimetry and the degradation products have been characterized by electron impact mass spectroscopy. Finally, N,N‐dimethylacrylamide was polymerized in the presence of these polyperoxides in toluene, highlighting their potential as polymeric free radical initiator during polymerization of vinyl monomers. © 2018 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2018 , 56, 2030–2038     

A benzophenone‐naphthalimide derivative as versatile photoinitiator of polymerization under near UV and visible lights

A benzophenone‐naphthalimide derivative (BPND) bearing tertiary amine groups has been developed as a high‐performance photoinitiator in combination with 2,4,6‐tris(trichloromethyl)‐1,3,5‐triazine or an iodonium salt for both the free radical polymerization (FRP) of acrylates and the cationic polymerization (CP) of epoxides upon exposure to near UV and visible LEDs (385–470 nm). BPND can even produce radicals without any added hydrogen donor. The photochemical mechanisms are studied by molecular orbital calculations, steady state photolysis, electron spin resonance spin trapping, fluorescence, cyclic voltammetry and laser flash photolysis techniques. These novel BPND based photoinitiating systems exhibit an efficiency higher than that of the well‐known camphorquinone‐based systems (FRP and CP) or comparable to that of bis(2,4,6‐trimethylbenzoyl)‐phenylphosphineoxide (FRP at λ ≤ 455 nm). © 2014 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2015 , 53, 445–451     

Bicarbazole-based oxalates as photoinitiating systems for photopolymerization under UV–Vis LEDs

Photoinitiators are critical to initiate chain reactions in photopolymerization. For such applications, the absorption of photoinitiator must be compatible with the emission of light sources and enables the fast manufacturing of three-dimensional network or structures. Light-emitting diode (LED) is a new kind of energy-saving and environmental protection light source, exhibiting a substantial response in the near UV and visible range to replace the traditional mercury lamp and other light sources in photopolymerization. Here, we introduce methyl oxalate into bicarbazole chromophore ( BiCz ). By variation of the single or double substituents in the BiCz , we demonstrate that the absorption spectra can be adjusted and redshift to visible range and show good absorption in the near UV and visible range (365–475 nm). We explore their photochemistry based on experimental results and theoretical calculations and the mechanism of photoreactions have been verified. The super photostability by themselves and good hydrogen abstraction ability from amine co-initiator make them as excellent near UV and visible light active photoinitiators. Critically, the photoinitiation of the free-radical polymerization of acrylate monomers with low content (0.1% concentration) upon LED irradiation at 365–475 nm, exhibits excellent application potential in light curing and other fields.     

Synthesis of star‐shaped poly(n‐butyl acrylate) oligomers with coumarin end groups and their networks for a UV‐tunable viscoelastic material

Solvent‐free isothermal tuning of viscoelasticity of polymer materials is important for an emerging photochemical molding technology and photoreversible adhesives. In this study we designed a four‐armed star‐shaped poly(butyl acrylate, BA) oligomer having four coumarin end groups. The irradiation of UV at the wavelength of 365 nm (UV₃₆₅) to the viscous poly(BA) oligomer under a solvent‐free condition produced a solid network material along with the progress of dimerization reaction with coumarin end groups. The subsequent irradiation of UV at the wavelength of 254 nm (UV₂₅₄) caused dimer dissociation reaction to attain change in the mixing degree of star and network architectures in the material. Moreover, viscoelasticity of the network material was tunable by repetitive UV₃₆₅ and UV₂₅₄ irradiations. © 2017 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2018 , 56, 9–15     

Novel photocurable monomers: The synthesis of difunctional vinyl ethers with a phosphonate group and difunctional 1‐propenyl ethers with a phosphonate group and their photoinitiated cationic polymerization

Phosphorus‐containing vinyl ether monomers and 1‐propenyl ether monomers were prepared by the regioselective addition reaction of glycidyl vinyl ether (GVE) or 1‐propenyl glycidyl ether with diaryl phosphonates with quaternary onium salts as catalysts. The reaction of GVE with bis(4‐chlorophenyl) phenylphosphonate gave bis[1‐(4‐chlorophenoxy methyl)‐2‐(vinyloxy)ethyl]phenylphosphonate in a 68% yield. The structures of the resulting phosphorus‐containing vinyl ether monomers and 1‐propenyl ether monomers were confirmed by IR and ¹H NMR spectra and elemental analysis. Photoinitiated cationic polymerizations of the resulting phosphorus‐containing vinyl ether monomers and 1‐propenyl ether monomers were investigated with photoacid generators. The polymerization of vinyl ether groups and 1‐propenyl ether groups of the obtained monomers proceeded very smoothly with a sulfonium‐type cationic photoinitiator, bis[4‐(diphenylsulfonio)phenyl]sulfide‐bis(hexafluorophosphate), upon UV irradiation. © 2005 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 43: 3105–3115, 2005     

Coupling selectivity in the radical‐controlled oxidative polymerization of 4‐phenoxyphenol catalyzed by (1,4,7‐triisopropyl‐1,4,7‐triazacyclononane)copper(II) complex

Various effects on the coupling selectivity of the oxidative polymerization of 4‐phenoxyphenol catalyzed by (1,4,7‐triisopropyl‐1,4,7‐triazacyclononane)copper(II) halogeno complex [Cu(tacn)X₂] are described. With respect to the amount of the catalyst and the nature of the halide ion (X) of Cu(tacn)X₂, the coupling selectivity hardly changed. The Cu(tacn) catalyst possessed a turnover number greater than 1860. As the temperature of the reaction and the polarity of the reaction solvent were elevated, the C O coupling at the o‐position increased, but the C C coupling was not involved. For the polymerization in toluene at 80 °C, poly(1,4‐phenylene oxide), obtained as a methanol‐insoluble part, showed the highest number‐average molecular weight of 4000 with a melting point (T_m) of 195 °C. Only a slight change in the coupling selectivity was observed in the presence or absence of hindered amines as the base. Surprisingly, however, the C O selectivity decreased from 100 to 24% with less hindered amines, indicating that the selectivity drastically changed from a preference for C O coupling to a preference for C C coupling. © 2000 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 38: 4792–4804, 2000     

Synthesis of imidazolium‐functionalized ionic polyurethane and formation of CdTe quantum dot–polyurethane nanocomposites

A series of positively charged imidazolium‐functionalized ionic polyurethanes (IPUs) were prepared in one‐step polymerization process by polymerization of presynthesized short‐chain imidazolium‐based ionic diol, polyethylene glycols with different molecular weights as long‐chain diols, and toluylene‐2,4‐diisocyanate. The structures of IPUs are confirmed by ¹H NMR analysis, and the thermogravimetric analysis measurement indicates that the IPUs have high degradation temperature. Fluorescent nanocrystal–polymer composites CdTe–IPU can be prepared conveniently, by the electrostatic interaction between positively charged IPUs and the negatively charged aqueous CdTe quantum dots (QDs). UV–vis absorption and photoluminescence spectra indicate the photochemical stability and strong fluorescent emission of CdTe–IPU composites. The quantum yields (QYs) of the composites are high and basically restore the QYs of the pure QDs. In addition, the transmission electron microscopy photographs show that the QDs in composites are uniform (about 3 nm in diameter) and monodisperse. The obtained nanocomposites are powder or elastomers with good film building. The casted CdTe–IPU films are transparent under visible light, and the colors of the composites and their films are vivid under a UV lamp. © 2011 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2011     

Disulfide‐centered poly(methyl acrylates): Four different stimuli to cleave a polymer

A series of poly(methyl acrylates) incorporating a disulfide center was subjected to four different stimuli to cleave the S S bond, as the weakest member of the chain. Four polymers with molecular weights in the range of 25–93 kDa were synthesized via Cu‐based atom transfer radical polymerization starting from a difunctionalized disulfide‐containing initiator. In tetrahydrofuran, the labile disulfide center was cleaved directly by mechanical force generated by ultrasound irradiation, whereas in chloroform, competing cleavage was also triggered by radical species that were generated by non‐mechanical sonolysis. A reductive cleavage was observed upon treatment with reducing agent, and a clean reversal of the cleavage via oxidation could be obtained if the terminal bromide was first removed via hydrogenolysis. This modified polymer allowed studies on a fourth strategy for the cleavage of the disulfide, namely, dynamic covalent exchange reactions with a fluorine labeled small molecule. While partially based on established protocols, this comparative study underscores the versatility of the disulfide bond for applications in stimuli‐responsive and adaptive materials. © 2018 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2018 , 56, 1404–1411     

Tuning the optical properties of ethynylene triptycene‐based copolymers via oxidation of their alkyne groups into α‐diketones

The synthesis of ethynylene triptycene‐based copolymers with various aromatic spacers ( 3a–d ) is reported using the palladium‐catalyzed Sonogashira cross‐coupling reaction. The alkyne groups of 3a–d were oxidized into their respective α‐diketone copolymers 4a–d . Formation of 3,4a–d was confirmed by several characterization techniques, such as, gel permeation chromatography (GPC), ¹H and ¹³C nuclear magnetic resonance (NMR), FT‐infrared (FTIR), UV–vis absorption, and emission spectroscopies. It was found that the nature of the aromatic spacer influences the emission properties of the target α‐diketone triptycene copolymers, causing either a red or blue‐shift with respect to that of their ethynylene triptycene copolymer synthons. Copolymers 4a–c with fluorene spacers reveal emission in the range of 440–475 nm, thus, qualifying them to act as blue emitters. © 2018 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2018 , 56, 931–937     

Initial step of anthracene‐sensitized photoacid generation from diphenyliodonium hexafluorophosphate in an epoxy matrix studied by steady‐state and laser‐flash photolyses

The anthracene‐sensitized photodecomposition of diphenyliodonium hexafluorophosphate was studied in an epoxy matrix. From steady‐state photolysis, the generation of protons, which are considered to be the actual initiators of the polymerization of epoxides, was confirmed. In addition, 9‐phenylanthracene was detected as a main product from anthracene. From time‐resolved laser‐flash photolysis, a broad absorption band with a peak at about 500 nm was observed that was thought to be due to the precursor of 9‐phenylanthracene. On the basis of these results, we propose electron transfer from anthracene in the excited singlet state to the diphenyliodonium cation as the initial step of photoacid generation. This process is followed by fast chemical reactions, which generate 9‐phenylanthracene and protons, and back electron transfer from the diphenyliodine radical to the anthracene cation radical. © 2001 John Wiley & Sons, Inc. J Polym Sci Part B: Polym Phys 39: 2937–2946, 2001     

Thiophene‐cored 2,2‐bis(methylol)propionic acid dendrimers for optical‐power‐limiting applications

The synthesis and characterization of dendron‐coated 2,5‐bis(phenylethynyl)thiophene chromophores are described. The dendrimers were grown divergently on the arylthiophene core with the versatile anhydride of 2,2‐bis(methylol)propionic acid. The arylthiophene core was synthesized with Sonogashira coupling reactions. Structurally well‐defined dendrimers up to the fourth generation were grown, as confirmed by size exclusion chromatography, NMR, and matrix‐assisted laser desorption/ionization time‐of‐flight analysis. The different dendritic substitution did not influence the absorption spectra of the compounds in or near the visible region. Solutions of arylthiophenes had good transparency at wavelengths greater than 400 nm. The dendritic thiophenes exhibited an optical‐power limit at the laser wavelength of 532 nm. However, the magnitude of the optical‐power limit of these compounds was slightly lower than that of a nondendritic arylthiophene with n‐pentyl substituents. © 2005 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 43: 1177–1187, 2005     

Facile synthesis of hyperbranched poly(p‐phenyleneethynylene‐alt‐m‐phenyleneethynylene) with narrow dispersity and high branching degree by sonogashira polymerization of an AB2 monomer

An AB₂ monomer PhBr₂  C  C  Ph  C  CH containing one acetylene group and two bromide groups was efficiently synthesized by a strategy based on the different reactivity between aromatic iodide and bromide in Sonogashira reaction. The Sonogashira polymerization of PhBr₂  C  C  Ph  C  CH was investigated to get hyperbranched poly(p‐phenyleneethynylene‐alt‐m‐phenyleneethynylene) (hb‐PMPE) in terms of the effects of monomer addition method, core molecule with different functionality, and ratio of [monomer]/[core molecule]. The results showed that narrow dispersities (D) (D: 1.23∼1.50) were obtained by slow monomer addition and with core molecule. Bifunctional core molecule induced narrower dispersity than monofunctional core molecule. The molecular weight of hb‐PMPE increased with increasing ratio of [monomer]/[core molecule], however, a negative deviation from calculated value was observed. The dispersity slightly increased with increasing [monomer]/[core molecule]. When the ratio of [monomer]/[core molecule] was below 50/1, monomodal distribution was observed; whereas when the ratio increased to 70/1, bimodal distribution was obtained. All the polymers showed degrees of branching (DBs) around 0.6. The hb‐PMPEs showed one major absorption band with λ_max around 330 nm, and emission band with λ_max around 390 nm. All the polymers showed relative quantum yields (Φ_r) above 0.5 in dilute THF solution. © 2017 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2018 , 56, 96–104     

Room‐Temperature and Aqueous‐Phase Synthesis of Plasmonic Molybdenum Oxide Nanoparticles for Visible‐Light‐Enhanced Hydrogen Generation

A straightforward aqueous synthesis of MoO_3?x nanoparticles at room temperature was developed by using (NH₄)₆Mo₇O₂₄?4 H₂O and MoCl₅ as precursors in the absence of reductants, inert gas, and organic solvents. SEM and TEM images indicate the as‐prepared products are nanoparticles with diameters of 90–180 nm. The diffuse reflectance UV‐visible‐near‐IR spectra of the samples indicate localized surface plasmon resonance (LSPR) properties generated by the introduction of oxygen vacancies. Owing to its strong plasmonic absorption in the visible‐light and near‐infrared region, such nanostructures exhibit an enhancement of activity toward visible‐light catalytic hydrogen generation. MoO_3?x nanoparticles synthesized with a molar ratio of Mo^VI/Mo^V 1:1 show the highest yield of H₂ evolution. The cycling catalytic performance has been investigated to indicate the structural and chemical stability of the as‐prepared plasmonic MoO_3?x nanoparticles, which reveals its potential application in visible‐light catalytic hydrogen production.     

Synthesis and optical properties of fluorene‐based polymers incorporating organosilicon unit

The synthesis and optical properties of polymers bearing the repeating unit of terfluorene and various organosilicon groups were investigated. Polymers with high molecular weight and good solubility could be obtained by Suzuki coupling polymerization from silylene‐containing fluorene‐based dibromo monomers and 9,9‐dihexylfluorene‐2,7‐bis(trimethyleneborate). From UV spectra of polymers bearing acyclic silylene bridge, the organosilicon units not only interrupted a π‐conjugation but also contributed to an electronic communication between connected fluorenes. The emission maximum wavelengths (ca. 400 nm) blue‐shifted when compared with that of polyfluorene (418 nm) and the fluorescence quantum yields were considerably high (>0.82) in the CHCl₃ solution. On the other hand, rather broad emission was observed at 480 nm and the fluorescence quantum yield was quite low (0.004) in the solution‐state PL spectrum of tetraphenylsilole‐containing polymer. The polymer emitted visible green light in the spin‐coated film. The fluorescence peak intensity at 486 nm gradually decreased when the film was illuminated with the UV light of 359 nm in air. © 2007 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 45: 4786–4794, 2007