Molecular orientation behavior of poly(vinyl chloride) as influenced by the nanoparticles and plasticizer during uniaxial film stretching in the rubbery stage

The structural evolution during uniaxial stretching of poly(vinyl chloride) films was studied using our real time spectral birefringence stretching machine. The effect of clay loading and the amount of plasticizer as well as the rate effects on the birefringence development and true mechanical response are presented with a final model summarizing the molecular phenomena during stretching. Mechano‐optical studies revealed that birefringence correlated with mechanical response (stress, strain, work) nonlinearly. This was primarily attributed to the preexisting strong network of largely amorphous chains connected via small crystallites that act as physical crosslinking points. These crystallites are not easily destroyed during the high‐speed stretching process as evidenced from the birefringence–true strain curves along with the X‐ray crystallinity measurements. At high speeds, the amorphous chains do not have enough time to relax and hence attain higher orientation levels. The crystallites, however, orient more efficiently when stretched at slow speeds. Apparently, some relaxation of the surrounding amorphous chains helps rotate the crystallites in the stretching direction. Overall birefringence is higher at high stretching speeds for a given true strain value. When the nanoparticles are incorporated, the orientation levels are increased significantly for both the crystalline and amorphous phases. Nanoplatelets increase the continuity of the network because they have strong interaction with the amorphous chains and/or crystallites. This in turn helps transfer the local stresses to the attached chains and increase the orientation levels of the chains. © 2005 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 43: 724–742, 2005     

Radiation effects on the thermal degradation of poly(vinyl chloride) and poly(vinyl alcohol)

Radiation effects on the formation of conjugated double bonds in the thermal degradation of poly(vinyl chloride) (PVC) and poly(vinyl alcohol) (PVA) were investigated. Thin films of PVC and PVA were either irradiated with γ-rays at ambient temperature (pre-irradiation) and then subjected to thermal treatment, or irradiated at elevated temperatures (in situ irradiation). An extensive enhancement of the thermal degradation was observed for the pre-irradiation of the PVC films, which was more effective than the effect of the in situ irradiation at the same absorption dose. For the PVA degradation, however, the effect of the in situ irradiation was larger than that of the pre-irradiation. The results were explained and related mechanisms were discussed based on radiation-induced chemical reactions and their individual contributions to the thermal degradation behaviors of the two polymers. © 1998 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 36: 3089–3095, 1998     

Grafting reactions of vinyl acetate onto poly[(vinyl alcohol)-co-(vinyl acetate)]

The grafting preference of vinyl acetate onto the methine carbon of poly(vinyl alcohol) (PVOH) versus the acetate group of poly(vinyl acetate) (PVAc) was determined as part of an attempt to prepare novel branched PVOH from partially hydrolyzed PVAc. The results showed long chain grafting on the acetate groups of the PVAc units rather than the methine carbons of the PVOH or PVAc units. Decreasing the monomer or initiator concentration decreased the molecular weight of the graft copolymer formed. Of the initiators studied, ammonium persulfate gave the largest increase in copolymer molecular weight. Both hydrolysis and reacetylation combined with gel permeation chromatography (GPC) and ¹³C-NMR of the fully hydrolyzed material were used to estimate the number and location of grafts. © 1996 John Wiley & Sons, Inc.     

Fully-biodegradable poly(3-hydroxybutyrate)/poly(vinyl alcohol) blend films with compositional gradient

Fully-biodegradable bacterial poly(3-hydroxybutyrate) (PHB)/chemosynthetic poly(vinyl alcohol) (PVA) blend films with compositional gradient from one surface to the other surface of the films were prepared by a dissolution-diffusion technique. Three kinds of PVA samples, high- and low-molecular weight atactic PVA and highly syndiotactic PVA (s-PVA), were used in order to investigate the effects of molecular weight and tactic structure on the generation of compositional gradient. The solution of PHB in 1,1,1,3,3,3-hexafluoro-2-propanol (HFIP), which is also a good solvent for PVA, was cast on the PVA film and then the solvent HFIP was evaporated. By selecting the optimum volume of solvent and the evaporation rate, the PHB/PVA blend film with compositional gradient was obtained. The formation of compositional gradient was confirmed by FT-IR microscopy and ATR-FT-IR analysis. The 50%/50% PHB/s-PVA blend film with a nearly ideal compositional gradient, that is, the composition of PHB (or PVA) in the film changing gradually from 100% at one surface to 0% at the other surface of the film was obtained by casting PHB/HFIP solution on to the s-PVA film. Positional dependence of the absorbance of C==O and OH stretching bands along the film thickness direction for the PHB/S-PVA cast films.     

Characterization of poly(vinyl alcohol) during the emulsion polymerization of vinyl acetate using poly(vinyl alcohol) as emulsifier

During the emulsion polymerization of vinyl acetate (VAc) using poly(vinyl alcohol) (PVA) as stabilizer and potassium persulfate as initiator, the VAc reacts with PVA forming PVA-graft-PVAc. When the grafted polymer reaches a critical size it becomes water-insoluble and precipitates from the aqueous phase contributing to the formation of polymer particles. Since particle formation and therefore the properties of the final latex will depend on the degree of grafting, it is important to quantify and to characterize the grafted PVA. In this work, the quantitative separation and characterization of the grafted water-insoluble PVA was carried out by a two-step selective solubilization of the PVAc latex, first with acetonitrile to separate PVAc homopolymer, followed by water to separate the water-soluble PVA from the remaining acetonitrile-insoluble material. After the separation, the water-soluble and water-insoluble PVA were characterized by Fourier Transform Infrared (FTIR) spectroscopy and ¹H and ¹³C nuclear magnetic resonance (NMR) analyses, from which the details of the PVA-graft-PVAc structure were obtained. © 1996 John Wiley & Sons, Inc.     

Liquid-state transitions (T>T g) of poly(vinyl alcohol)

The two liquid state transitions,T _ll andT _ll, of non-crystalline, uncrosslinked poly(vinyl alcohol) were determined by differential scanning calorimetry.T _ll increased as the molecular weightM _n increased, whileT _ll remained almost constant. Crosslinking and crystallinity lead to disappearance of the transitionT _ll. The transitionT _ll was linked to mobility of whole chains, whereasT _ll was characteristic of segmental mobility.     

Synthesis of poly(vinyl alcohol-graft-hyperbranched glycerol)

We report the first example of grafting hyperbranched polyglycerol onto poly(vinyl alcohol) via ring-opening polymerisation of glycidol to prepare poly(vinyl alcohol-graft-hyperbranched glycerol) (P[(VA)-g-(hPG)]). The effects of catalyst, molecular weight of PVA, reaction temperature, water content, moles of reagent, and addition time of reagent were also investigated. P[(VA)-g-(hPG)] with various mole fractions of hPG were prepared and the degrees of substitution and branching were determined. P[(VA)-g-(hPG)] displayed decreased degree of crystallinity and also increased solubility in water, compared to PVA. P[(VA)-g-(hPG)] is shown to be a superior hair styling polymer with a curl retention value of 85% after 4 h. © 2017 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2017 , 55, 3041–3047     

Structure and compatibility of poly(vinyl alcohol)-silk fibroin (PVA/SA) blend films

The structure and compatibility of poly(vinyl alcohol)-silk fibroin (PVA/SF) blend films were analyzed by differential scanning calorimetry (DSC), thermomechanical (TMA) and thermogravimetric (TGA) analysis, x-ray diffractometry, and scanning (SEM) and transmission (TEM) electron microscopy. DSC curves of PVA/SF blend films showed a major endothermic peak at 220°C, along with a peak at 280°C. These endotherms were assigned to the thermal decomposition of the ordered PVA elements and to the thermal degradation of silk fibroin, respectively. The PVA/SF blends behaved in a manner intermediate to the pure components, as suggested by both contraction expansion and sample weight retention properties recorded by TMA and TGA measurements. The IR absorption spectra of the blends were identified as purely a composite of the absorption bands characteristic of both PVA and SF pure polymers. The X-ray diffraction patterns of PVA/SF blends showed overlapping spacing due to PVA and SF. A dispersed phase formed by spherical particles of 3–7 μm diameter was observed by SEM and TEM. All these findings suggest that PVA and SF are incompatible. © 1994 John Wiley & Sons, Inc.     

Effect of poly(ethylene oxide) on the structure and properties of poly(vinyl alcohol)

To improve the drawability of poly(vinyl alcohol) (PVA) thermal products, poly(ethylene oxide) (PEO), a special resin with good flexibility, excellent lubricity, and compatibility with many resins, was applied, and the Fourier transform infrared spectroscopy, dynamic mechanical analysis (DMA), differential scanning calorimetry (DSC), and wide‐angle X‐ray diffraction (WXRD) were adopted to study the hydrogen bonds, water states, thermal properties, crystal structure, and nonisothermal crystallization of modified PVA. It was found that PEO formed strong hydrogen bonds with water and PVA, thus weakened the intra‐ and inter‐hydrogen bonds of PVA, changed the aggregation states of PVA chains, and decreased its melting point and crystallinity. Moreover, the interactions among PVA, water, and PEO retarded the water evaporation and made more water remain in the system to plasticize PVA. The existence of PEO also slowed down the melt crystallization process of PVA, however, increased the nucleation points of system, thus made more and smaller spherulites formed. The weakened crystallization capability of PVA and the lubrication of PEO made PVA chains to have more mobility under the outside force and obtain high mechanical properties. © 2010 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 48: 1946–1954, 2010     

Solid‐state 13C and 129Xe NMR study of poly(vinyl alcohol) and poly(vinyl alcohol)/lactosilated chitosan gels

Dry and hydrated poly(vinyl alcohol) (PVA) gels with 55% (a‐PVA) and 61% (s‐PVA) syndiotacticity and related PVA/lactyl chitosan (LC) blends have been investigated with ¹²⁹Xe and cross‐polarization/magic‐angle‐spinning ¹³C NMR techniques. Although the dry gels exhibit two broad ¹²⁹Xe resonances in the slow‐to‐intermediate exchange limit, both hydrated gels show three resonances. The corresponding dry blends exhibit two signals, the chemical shifts and line widths of which change with respect to those of pure PVA, whereas one (a‐PVA/LC) or two (s‐PVA/LC) signals appear in the spectra of the hydrated blends. A comparative analysis of the data demonstrates that LC rearranges the domains of the polymeric matrix in both the dry and hydrated blends according to the syndiotacticity of the PVA chains. Information on the molecular motions of the amorphous and swollen polymeric domains in the kilohertz range has been obtained from an analysis of the spin‐lattice relaxation times. These data indicate that the dynamics and arrangement of the PVA chains in the gels are strongly affected by their tacticity and the addition of the copolymer LC. © 2003 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 41: 3123–3131, 2003     

部分醇解聚乙烯醇接枝聚对二氧环己酮的合成与表征

制备了部分醇解的PVA(paPVA),将其与PDO在均相本体接枝聚合,通过对paPVA醇解度以及投料比的选择,得到了具有各种分子结构的接枝共聚物.通过一维核磁共振谱表征了聚合物的微观结构;采用TG、DSC等测试手段研究了接枝共聚物的热性能和结晶性能.     

New chemical hydrogels based on poly(vinyl alcohol)

The syntheses of two new types of chemical hydrogels based on poly(vinyl alcohol), PVA, are reported. Common to both synthetic routes is the preparation of a telechelic PVA (tel-PVA) obtained by periodate splitting of the vicinal diol units present in few percent along the chain. tel-PVA was then used as crosslinking agent with chitosan and PVA in two simple reactions in aqueous phase such as reductive alkylation of chitosan and acetalyzation of PVA. Both reactions yielded firm wall-to-wall networks showing marked differences in their swelling capability. © 1996 John Wiley & Sons, Inc.     

弹性体偶联剂结构对PVC/PPC性能的影响

NBR－PPC弹性体偶联剂能促进PPC（聚丙撑碳酸酯）与PVC（聚氯乙烯）之间的相容性，改善共混物的力学性能，并在共混体系中产生轻度交联。偶联剂组成在NBR／PPC比例为70／30，NBR（丁腈橡胶）含腈量为34％，BPO过氧化苯甲酸用量为2．5份时，共混物的综合力学性能最佳，但偶联剂预先硫化时间不宜过长．     

Dissolution mechanism of semicrystalline poly(vinyl alcohol) in water

Changes occurring in the degree of crystallinity and lamellar thickness distribution of poly(vinyl alcohol) (PVA) samples during dissolution in water were investigated. PVA samples of three different molecular weights were crystallized by annealing at 90, 110, and 120°C. The initial degrees of crystallinity measured by differential scanning calorimetry (DSC) and by attenuated total reflection Fourier transform infrared spectroscopy (ATR-FTIR) varied from 43 to 60% and the average lamellar thicknesses measured by DSC ranged from 50 to 400 Å. PVA dissolution was followed at 25, 35, and 45°C from 30 s up to 195 min. Lamellar thicknesses were determined as a function of dissolution time using DSC. There was an initial drastic decrease in the degree of crystallinity, which leveled off to a fairly constant value before reaching zero by the time the polymer dissolved completely. Increase in molecular weight led to lesser number of crystals, but with larger average lamellar thickness, which were more stable in the presence of water. Increase in crystallization temperature or decrease in dissolution temperature led to larger average lamellar thickness. Based on these findings, a dissolution mechanism involving unfolding of the polymer chains of the crystal was proposed. © 1996 John Wiley & Sons, Inc.     

Morphology of poly(vinyl alcohol) gels assuring the greatest significant drawability

Atactic poly(vinyl alcohol) (at-PVA) and syndiotactic poly(vinyl alcohol) (st. PVA) prepared by gelation/crystallization using dimethyl sulphoxide/water mixtures were drawn in a hot oven at 160 °C under nitrogen. The degrees of polymerization of at- and st-PVA were 2000 and 1980, respectively. The drawability of at- and st-PVA films was affected by the composition of the solvent mixture as well as by quenching temperature. The drawability of at- and st-PVA films prepared by using the solvent mixture containing 60% of dimethyl sulphoxide and 40% of water became more pronounced as the temperature of gelation/crystallization decreased and the draw ratio reached maximum value at –80 °C. Namely, the greatest significant drawability was the same condition for at- and st-PVA films in spite of the different stereo-regularity. Even in this common best condition for significant drawability, however, the morphological properties of swollen gels and of the resultant dry gel films are different each other, dependent upon the tacticity. For at-PVA, small-angle light scattering under Hv polarization condition could not be observed in the swollen gels and in the dry films when the solutions were quenched at temperatures <–10 °C. In contrast, for st-PVA, the X-type scattering pattern from swollen gels became clearer as the temperature decreased but the pattern became indistinct under drying process at ambient condition. On the other hand, the fibrillar textures within the at- and st-PVA dry films became finer and the orresponding crystallinity became lower as the temperature of gelation/crystallization decreased. Thus it turned out that the morphological properties of the swollen gels and of the dried films play an important role to assure the greatest significant drawability.     

Study on ketalization reaction of poly(vinyl alcohol) by ketones. VIII. kinetic study on acetalization and ketalization reactions of poly(vinyl alcohol)

The kninetics of acid-catalyzed acetalization and ketalization of poly(vinyl alcohol) (PVA) were systematically studied in completely homogeneous media with carefully selected solvents. Thus the acetalization reaction was run in water with six aldehydes [R₁CHO (R₁ = H, CH₃, C₂H₅, n-C₃H₇, i-C₃H₇, ClCH₂)], whereas the ketalization in dimethylslfoxide with 11 ketones [R₂CH₃CO (R₂ = CH₃, C₂H₅, n-C₃H₇, i-C₃H₇, n-C₄H₉, i-C₄H₉, tert-C₄H₉, C₆H₅CH₂, C₆H₅CH₂CH₂), cyclopentanone, and cyclohexanone]. The latter was difficult to proceed in aqueous media. Both reactions were reversible and bimolecular and, despite the use of different solvents, gave similar heats of reaction (7.5 kcal/mol) and activation energies (ca. 15 kcal/mol) except for the case of formaldehyde and chloroacetaldehyde; however the equilibrium constants at 25°C showed that the acetalization is thermodynamically much more favored than the ketalization (ca. 5000 vs. 0.01–0.9), probably because of steric hindrance of the ketone substrate. The rate constants of hydrolysis (reverse reactions) for the poly(vinyl acetal) and poly(vinyl ketal) followed the Hammett-Taft equation to give a single p* (=3.60) that is very close to that for the hydrolysis of diethyl acetal and ketal. From these and other data, it was concluded that the polymer hydrolysis, as well as PVA acetalization and ketalization, are all electrophilic reaction where the formation of hemiacetal or hemiketal is the rate-determining step. © 1996 John Wiley & Sons, Inc.     

Preparation of antimicrobial poly(vinyl alcohol) nanofibers containing silver nanoparticles

Polyvinyl alcohol (PVA) nanofibers containing Ag nanoparticles were prepared by electrospinning PVA/silver nitrate (AgNO₃) aqueous solutions, followed by short heat treatment, and their antimicrobial activity was investigated for wound dressing applications. Since PVA is a water soluble and biocompatible polymer, it is one of the best materials for the preparation of wound dressing nanofibers. After heat treatment at 155 °C for 3 min, the PVA/AgNO₃ nanofibers became insoluble, while the Ag⁺ ions therein were reduced so as to produce a large number of Ag nanoparticles situated preferentially on their surface. The residual Ag⁺ ions were reduced by subsequent UV irradiation for 3 h. The average diameter of the Ag nanoparticles after the heat treatment was 5.9 nm and this value increased slightly to 6.3 nm after UV irradiation. It was found that most of the Ag⁺ ions were reduced by the simple heat treatment. The PVA nanofibers containing Ag nanoparticles showed very strong antimicrobial activity. © 2006 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 44: 2468–2474, 2006     

Silylation of poly(vinyl alcohol) with hexamethyldisilazane in liquid ammonia

Silylation of poly(vinyl alcohol) has been performed with hexamethyldisilazane in liquid ammonia in an autoclave. This novel procedure has the advantage that the educt, the reagent, and the product are soluble in ammonia, which works under homogeneous conditions. No salt like by-products are formed and no tedious purification of the product is necessary. The degree of silylation has been adjusted through the ratio of silylating agent to hydroxy groups. Random incorporation of trimethylsilyl groups was proven by the linear dependence of the glass transition temperature from the degree of silylation and the solubility of the partially silylated material. Quantitative investigation of the silylation reaction showed first-order kinetics for the initial and final stages of the reaction indicative of a reaction where k₁ > k₂ > k₃. © 1995 John Wiley & Sons, Inc.     

Alignment effect of attapulgite on the mechanical properties of poly(vinyl alcohol)/attapulgite nanocomposite fibers

Poly(vinyl alcohol) (PVA)/attapulgite (AT) nanocomposite fibers have been prepared by wet spinning. The morphology and mechanical properties of the modified PVA fibers have been characterized with transmission electron microscopy, scanning electron microscopy (SEM), differential scanning calorimetry (DSC), birefringence measurements, and mechanical testing. The PVA/AT nanocomposite fibers show much higher tensile strength, initial modulus, and work to break than pure PVA fibers with the same draw ratio. SEM observations demonstrate that the AT nanorods can align orderly along the fiber axis by stretching and have good adhesion to the fiber matrix. The results of birefringence measurements prove that the modified fibers have higher orientation than pure PVA fibers after stretching. The results of DSC analysis indicate that the crystallinity of the PVA fibers can be increased by the addition of AT. © 2006 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 44: 1995–2000, 2006     

Synthesis of isotactic star-shaped poly(vinyl alcohol)

Isotactic 6-armed star-shaped poly(vinyl alcohol) (PVA) with a narrow molecular weight distribution was successfully prepared by the living cationic polymerization of 6-armed star-shaped poly(tert-butyl vinyl ether) (PTBVE) and subsequent acidic ether cleavage. The PTBVE was synthesized using hexa(chloromethyl) melamine (HCMM) as a hexafunctional initiator and ZnI₂ or ZnCl₂ as an activator in toluene/MC (1/1 v/v) at −70 °C. A better living stability of PTBVE was obtained in the ZnCl₂ activator system. The number average molecular weight and the polydispersity index of the 6-armed star-shaped PTBVE polymerized with ZnCl₂ at −70 °C for 24 h were 156,000 g/mol and 1.47, respectively. The fraction of the mm sequence of the resulting PVA was 52%.