Adsorption and orientation kinetics of self‐assembled films of octadecyltrimethoxysilane on aluminium oxide surfaces

X‐ray photoelectron spectroscopy (XPS) and near‐edge x‐ray absorption fine structure (NEXAFS) spectroscopy have been used to study the time‐dependent adsorption and molecular orientation behaviour of octadecyltrimethoxysilane (ODTMS) on native aluminium oxide surfaces. By measuring the adsorption isotherm using XPS, we show that ODTMS molecules exhibit oscillatory adsorption. The oscillatory adsorption behaviour for ODTMS is analogous to that observed for its simpler short‐chain ‘cousin’—propyltrimethoxysilane (PTMS)—and suggests that the length of the functional alkyl chain on an organosilane does not have a significant influence upon the oscillatory adsorption mechanism. The oscillation in the ODTMS adsorption isotherm shows a maximum and a minimum in coverage at an adsorption time of ～30 and ～65 s, respectively, for a 0.75% ODTMS solution in a 90% ethanol–10% water mixture at pH 4. The time‐dependent orientation behaviour of the ODTMS molecules during adsorption was examined using angular‐dependent carbon K‐edge NEXAFS spectroscopy. We show that the alignment of the ODTMS film changes systematically with deposition time and appears to be correlated with coverage measurements obtained using XPS. In particular, by combining the XPS and NEXAFS results we demonstrate that the minimum ODTMS coverage corresponds to a film whose alignment appears to be predominantly randomized. Copyright © 2005 John Wiley & Sons, Ltd.     

Computational screening of biomolecular adsorption and self‐assembly on nanoscale surfaces

The quantification of binding properties of ions, surfactants, biopolymers, and other macromolecules to nanometer‐scale surfaces is often difficult experimentally and a recurring challenge in molecular simulation. A simple and computationally efficient method is introduced to compute quantitatively the energy of adsorption of solute molecules on a given surface. Highly accurate summation of Coulomb energies as well as precise control of temperature and pressure is required to extract the small energy differences in complex environments characterized by a large total energy. The method involves the simulation of four systems, the surface‐solute–solvent system, the solute–solvent system, the solvent system, and the surface‐solvent system under consideration of equal molecular volumes of each component under NVT conditions using standard molecular dynamics or Monte Carlo algorithms. Particularly in chemically detailed systems including thousands of explicit solvent molecules and specific concentrations of ions and organic solutes, the method takes into account the effect of complex nonbond interactions and rotational isomeric states on the adsorption behavior on surfaces. As a numerical example, the adsorption of a dodecapeptide on the Au {111} and mica {001} surfaces is described in aqueous solution. © 2009 Wiley Periodicals, Inc. J Comput Chem, 2010     

Photosensitive,self‐assembled ultrathin films based on diazoresin and phosphate‐containing polyanions

Photosensitive ultrathin films with phosphate‐containing polyanions and diazoresin (DR) as a polycation were fabricated with a self‐assembly technique. The phosphate‐containing polyanions were poly(sodium phosphate), phosphorylated poly(vinyl alcohol), and DNA. The fabrication process was monitored by the determination of the absorbance from DR. The surface morphology of the multilayer films was observed with atomic force microscopy. Under ultraviolet irradiation, the linkage between the layers of the films changed from being ionic to being covalent; as a result, the stability of the films toward polar solvents increased. This kind of film may have applications for biosensor devices. © 2001 John Wiley & Sons, Inc. J Polym Sci Part A: Polym Chem 40: 222–228, 2002     

Lotus bioinspired superhydrophobic,self‐cleaning surfaces from hierarchically assembled templates

The super hydrophobic, self‐cleaning properties of natural species derive from the fine hierarchical topography evolved on their surfaces. Hierarchical architectures which are function‐mimetic of the lotus leaf are here described and created from multi‐scale hierarchical assembled templates. The first level of hierarchy was a micromachined dome structure template and the second level of hierarchy was added by layering a thin nanoporous membrane such as porous anodized alumina or an ion track etch membrane. The assembled templates were nanoimprinted by a single step process on thermoplastic films. The wetting angle of the surfaces reached a value of 160° and the self‐cleaning behavior was observed. The superhydrophobic behavior remained over 1 year after fabrication, which demonstrates the stability of these polymeric self‐cleaning topographies. © 2014 Wiley Periodicals, Inc. J. Polym. Sci. Part B. Polym. Phys. 2014 , 52, 603–609     

Ion condensation onto self‐assembled nanofibers

Self‐assembled peptide amphiphile (PA) nanofibers are a class of supramolecular materials with promising applications in nanotechnology. Alignment of nanofibers, which is essential for biomaterials applications, is achieved at low salt concentrations in the PA nanofiber suspensions. Regardless of its importance, the effect of ion concentration on the properties of these nanostructures remains unexplored. Using atomistic molecular dynamics simulations, canonical PA nanostructures are investigated to elucidate the relationship between counterion condensation and morphological changes. Simulations reveal that nanofibers with the highest cross‐section density have expanded radii. This expansion decreases the accessible volume for sodium counterions and diminishes the counterion translational entropy, while also reducing the total electrostatic potential. Interestingly, we show that the competition between these effects leads to a fraction of condensed counterions independent of the fiber radius. © 2017 Wiley Periodicals, Inc. J. Polym. Sci., Part B: Polym. Phys. 2017 , 55, 901–906     

Functionalized block copolymers for preparation of reactive self‐assembled surface patterns

Two phase separating block copolymers equipped with functional groups (acid and alkyne) were synthesized via reversible addition‐fragmentation chain transfer (RAFT) polymerization. Thin films of these materials were prepared and examined with regard to surface morphology, surface composition, and film stability. Self‐assembled structures with domain sizes of about 40 nm were detected through atomik force microscopy (AFM) analysis while X‐ray photoelectron spectroscopy measurements revealed a balanced surface exposure of the two segregated phases. Thus, reactive groups being present in both phases are specifically provided within nanoscopic surface areas. The films showed good stability on exposure to various solvents but the self‐organized surface patterns were only resistant toward ethanol. © 2011 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2011     

Formation of long‐range stripe patterns with sub‐10‐nm half‐pitch from directed self‐assembly of block copolymer

We have demonstrated directed self‐assembly of poly(styrene‐b‐dimethylsiloxiane) (PS‐b‐PDMS) down to sub‐10‐nm half‐pitch by using grating Si substrate coated with PDMS. The strong segregation between PS and PDMS enables us to direct the self‐assembly in wide grooves of the grating substrate up to 500 nm in width. This process can be applied to form various type of sub‐10‐nm stripe pattern along variety of grating shape. © 2010 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys, 2010     

Control of nano/microstructure and pit initiation sites on aluminium surface by use of self‐assembled spheres

Nano/microstructure control and electrochemical etching of aluminium substrate using a honeycomb alumina mask fabricated by anodisation with self‐assembled spheres aligned on the aluminium surface were studied to directly control the initiation sites of pits. The transfer of the hexagonally ordered pattern of self‐assembled spheres to the aluminium substrate could be achieved by substantially suppressed anodic oxide growth under the spheres where selective electrochemical etching proceeded. That is, etch pits are generated only in the thinner areas or holes of the honeycomb alumina mask with a one‐to‐one correspondence. With this process, improvements in pit distribution density and the homogeneity of pit sizes, while avoiding excessive dissolution of the aluminium surface, could be achieved easily in comparison with the conventional method. The density of pits could also be controlled by changing the diameter of spheres used as an indirect mask. Copyright © 2010 John Wiley & Sons, Ltd.     

Self‐assembly of metallo‐supramolecular block copolymers in thin films

The self‐assembly of a metallo‐supramolecular PS‐[Ru]‐PEO block copolymer, where ‐[Ru]‐ is a bis‐2,2′:6′,2″‐terpyridine‐ruthenium(II) complex, in thin films was investigated. Metallo‐supramolecular copolymers exhibit a different behavior as compared to their covalent counterparts. The presence of the charged complex at the junction of the two blocks has a strong impact on the self‐assembly, effecting the orientation of the cylinders and ordering process. Poly(ethylene oxide) cylinders oriented normal to the film surface are obtained directly regardless of the experimental conditions over a wide range of thicknesses. Exposure to polar solvent vapors can be used to improve the lateral ordering of the cylindrical microdomains. © 2008 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 46: 4719–4724, 2008     

Covalently attached self‐assembly of ultrathin films from hydroxy‐containing porphyrin and diazoresin

Ultrathin films from 5,10,15,20‐tetrakis(4‐hydroxyphenyl) porphyrin (HPP) and diazoresin (DR) via a H bonding interaction were fabricated with the self‐assembly technique. Under UV irradiation, the H bonds between the layers will convert to covalent bonds following the decomposition of the diazonium group of DR. The stability of the film against the polar solvent and electrolyte aqueous solution increases a lot because of the formation of the covalent crosslinking structure. Thus, the photoelectric conversion property of DR/HPP film can be measured directly with a normal photoelectric chemical cell with potassium chloride as the electrolyte. The maximum of the anodic photocurrent was measured as 1.7 μ Å for an eight bilayer DR/HPP film deposited on an indium–tin oxide glass electrode. The action spectrum of the photocurrent generation indicated that the HPP contained in the film is responsible for the generation of the observed photocurrent. © 2003 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 41: 3103–3108, 2003     

Behaviors of self‐assembled diblock copolymer with pendant photosensitive azobenzene segments

A novel monomer, ethyl 4‐[4‐(11‐methacryloyloxyundecyloxy)phenyl azobenzoyl‐oxyl] benzoate, containing a photoisomerizable N?N group was synthesized. The monomer was further diblock copolymerized with methyl methacrylate. Amphiphilic diblock copolymer poly(methyl methacrylate‐block‐ethyl 4‐[4‐(11‐methacryloyloxyundecyloxy)phenyl azobenzoyl‐oxyl] benzoate ( PMMA ‐ b ‐ PAzoMA ) was synthesized using atom transfer radical polymerization. The reverse micelles with spherical construction were obtained with 2 wt % of the diblock copolymer in a THF/H₂O mixture of 1:2. Under alternating UV and visible light illumination, reversible changes in micellar structure between sphere and rod‐like particles took place as a result of the reversible E‐Z photoisomerization of azobenzene segments in PMMA ‐ b ‐ PAzoMA . Microphase separation of the amphiphilic diblock copolymer in thin films was achieved through thermal and solvent aligning methods. The microphases of the annealed thin films were investigated using atom force microscopy topology and scanning electron microscopy analyses. © 2010 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 48: 1142–1148, 2010     

Brushless and controlled microphase separation of lamellar polystyrene‐b‐polyethylene oxide thin films for block copolymer nanolithography

Creating perpendicular alignment in lamellar block copolymer (BCP) systems has considerable industrial and commercial significance, most importantly for generating nanowire structures in electronic devices. In general, these lamellar systems require careful interface engineering to obtain vertical orientation of the blocks. To avoid the strong preferential adsorption of one block to either the substrate or the polymer/air interface, the surface must be “neutralized” by chemical brushes or external forces, for example, solvent fields. Reported here is a stepwise thermo/solvent annealing process allowing the formation of perpendicular domains of polystyrene‐b‐polyethylene oxide lamellar structures while avoiding brush or other surface modifications. This BCP has a relatively small minimum feature size and can be used to generate substrate patterns for use in fabrication of nanowire electronic device structures. © 2012 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys, 2012     

Syntheses of polyolefin‐based stereoregular diblock copolymers for self‐assembled nanostructures

The preparation of polyolefin‐based stereoregular diblock copolymers by postpolymerization of ethenyl‐capped syndiotactic polypropylene‐based propylene/norbornene copolymer (sPP‐based P‐N copolymer) led to the successful generation of a structurally uniform stereoregular diblock copolymer for self‐assembly studies. The ethenyl‐capped prepolymer was prepared by conducting propylene/norbornene copolymerization in the presence of Me₂C(Cp)(Flu)ZrCl₂/MAO. Ozonolysis of ethenyl‐capped sPP‐based P‐N copolymer provided the formyl group end‐capped, end‐functionalized prepolymer with a quantitative functional group conversion ratio. Subsequently, connecting the formyl end‐group of the stereoregular prepolymer by coupling with living anionic polystyrene resulted in the high yield production of stereoregular diblock copolymer (sPP‐based P‐N‐block‐polystyrene), which is difficult to prepare by other methods. The resulting stereoregular diblock copolymer possesses precise chemical architecture to self‐organize into consistent nanostructures as evidenced by transmission electron microscopy and small angle X‐ray scattering. © 2008 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 46: 4843–4856, 2008     

Optical and physical properties of iridescent photonic crystals obtained by self‐assembled polymethyl methacrylate nanospheres within graphene oxide nanoplatelets

Opal photonic crystals prepared by vertical templating of polymethyl methacrylate (PMMA) nanospheres in aqueous graphene oxide (GO) solutions were successfully obtained. The results show that increasing the PMMA nanospheres' size leads to the modification of the d‐spacing in GO nanoplatelets, inducing brilliant iridescence colors that span the entire visible electromagnetic spectrum. Scanning electron microscopy study shows a uniform distribution of GO nanoplatelets on the surface and the bulk of the opal photonic crystals. The reflectance spectra exhibit a significant red shift from 385 to 660 nm when the nanospheres' size increases from 160 to 306 nm, respctively. The Raman spectra show a systematic decrease in the intensity ratio of the D to G bands of GO (I_D/I_G), suggesting a partial reduction of graphene oxide with decrasing the extent of defects in the partially reduced GO nanoplatelets. This finding is confirmed by the significant decrease observed in the intensity of the hydroxyl band in the attenuated total reflectance mode‐Fourier transform infrared spectra of the photonic crystals. The results provide the first demonstrated example of intercalated assemblies of polymer nanospheres within GO nanosheets, leading to photonic crystals with brilliant iridescence colors that span the entire visible electromagnetic spectrum and can be tuned only by varying the size of the PMMA nanospheres.     

Stabilization of self‐assembled microdroplets using short chain alcohols

The condensation of water vapor on a volatile polymeric solution leads to a porous surface after evaporation of both solvent and water. However, the stabilization of the water microdroplet is of great importance, which can be achieved using specific polymer or adding a third substance to the polymer solution. Short chain alcohols (methanol, ethanol, and n‐propanol) are utilized to fabricate a self‐assembled porous honeycomb film of linear, low molecular weight polystyrene using the breath figure technique. A combination of breath figure processing and the effect of alcohol on a water droplet can stabilize the pattern and make pores on the surface of the polymer film. The quality of the porous honeycomb film is strongly dependent on the type of alcohols and the concentration of polymer. In a specific range of polymer and alcohol concentration, pores cover all the surface of the polymer film. This method offers the possibility of producing a honeycomb structure with no trace of additive residual after the fabrication process and avoiding polymer modification. © 2015 Wiley Periodicals, Inc. J. Polym. Sci., Part B: Polym. Phys. 2015 , 53, 709–718     

Formation of alkane‐phosphonic acid self‐assembled monolayers on alumina: an in situ SPR study

The formation process of n‐alkane phosphonic acid CH₃ (CH₂)_n?1 PO(OH)₂ (n = 10,12,14,18) self‐assembled monolayers (SAMs), deposited from ethanol solutions on aluminum oxide, has been monitored in situ using surface plasmon resonance (SPR) spectroscopy. In addition, the two‐solvent approach is used to obtain both film thickness and refractive index of the fully formed adsorbed layers. A densely packed adsorbed layer is formed only for the longest molecules with n = 18. The chain length and solution concentration dependence of formation kinetics are studied, and the existence of two distinct kinetic steps is revealed. Fittings of the experimental results with various kinetic models are performed. Our analysis suggests that during the first kinetic step, a transition from a lying‐down to a standing‐up phase takes place, and the growth of this standing‐up phase is governed by second‐order kinetics. The second slow kinetic step is described by a modified first‐order Langmuir law. Copyright © 2009 John Wiley & Sons, Ltd.     

Interfacial chemistry of adhesives on hydrated aluminium and hydrated aluminium treated with an organosilane

The adsorption of a commercial adhesive and two of its major components—an amine curing agent [2,4‐toluene diisocyanate urone (TDI urone)] and an adhesive prepolymer resin [diglycidyl ether of bisphenol A (DGEBA)]—on a hydrated aluminium surface and the hydrated surface coated with γ‐glycidoxypropyltrimethoxysilane (GPS) has been investigated by x‐ray photoelectron spectroscopy (XPS) and time‐of‐flight secondary ion mass spectrometry (ToF‐SIMS). The study of TDI urone adsorption indicated that adsorption was of the chemisorption type, and a specific interaction involving this molecule and the GPS immobilized on the hydrated aluminium surface was identified. From XPS and ToF‐SIMS data it was found that the types of interaction of the curing agent with the bare substrate were of the donor–acceptor type. Study of the DGEBA adsorption showed different‐shaped isotherms for the bare and the GPS‐coated substrates. It was found that the typical Langmuir isotherm type was obtained for the GPS‐coated substrate whereas no adsorption plateau was observed for the bare substrate within the concentration range studied. This resulted from a change in the conformation of the DGEBA molecule on the substrate when the concentration of DGEBA solution was increased. The bonding of DGEBA with both types of substrates was assumed to be via acid–base interactions (i.e. donor–acceptor interactions). Adsorption of the commercial adhesive on the hydrated surfaces was of BET Type IV form, rather than the simple monolayer adsorption isotherm (Langmuir type). This indicates multilayer adsorption, presumably in the pores of the hydrated substrate, as a result of a process analogous to adsorption condensation. Copyright © 2004 John Wiley & Sons, Ltd.     

Sacrificial BSA to block non‐specific adsorption on organosilane adlayers in ultra‐high frequency acoustic wave sensing

This follow‐up study describes the implementation of recently developed cross‐linking trichlorosilane surface chemistry with acoustic wave sensing technology for the real‐time and label‐free detection of biotin/avidin interactions. Biosensing platforms consist of unelectroded piezoelectric quartz resonator discs onto which functionalizable mixed organosilane adlayers are prepared using a new trichlorosilane cross‐linker in combination with a shorter monofunctional diluent molecule. Thiolated or aminated biotin probes can next be anchored to the mixed assembly in a single, preactivation‐free step through site‐specific coupling at pentafluorophenyl ester head moieties. Biosensing properties are assessed at ultra‐high frequency (>0.74 GHz) with the highly sensitive electromagnetic piezoelectric acoustic sensor using micromolar buffered solutions of avidin. This biosensor prototype – which generally displays good reproducibility – uses sacrificial bovine serum albumin to block non‐specific adsorption. This preliminary work in buffer constitutes an important step towards the development of real‐world biosensors able to perform with more demanding biological samples. Copyright © 2013 John Wiley & Sons, Ltd.     

Comparative study of self‐assembly of a range of monofunctional aliphatic molecules on magnetron‐sputtered aluminium

The adsorption of a range of organic molecules from toluene onto the oxidized surface of magnetron‐sputtered aluminium metal is studied using sessile drop water contact angle measurements. Molecules with different head group functionalities and various chain lengths are considered, including alkyl carboxylic acids, alkyl phosphonic acids, alkyl amines, alkyl trimethoxysilanes, alkyl trichlorosilanes and epoxy alkanes. Alkyl phosphonic and carboxylic acids are identified as readily forming the most well‐packed monolayers on the aluminium surface, whereas the others adsorb less well and the chlorosilanes polymerize as a result of combination with moisture to form a thick deposit. The high‐adsorption‐density monolayers of alkyl phosphonic and carboxylic acids were studied using polarization modulation infrared reflection–absorption spectroscopy (PM‐IRRAS) and x‐ray photoelectron spectroscopy (XPS): PM‐IRRAS reveals relatively poorer ordering of the C₁₀ alkyl carboxylic acid monolayer compared with that formed from the phosphonic acid, and XPS data suggest that this is likely to relate to a lower ability to displace preadsorbed volatile organic compounds. Copyright © 2004 John Wiley & Sons, Ltd.