TiO<Subscript>2</Subscript>-water nanofluid in a porous channel under the effects of an inclined magnetic field and variable thermal conductivity

The TiO₂-water based nanofluid flow in a channel bounded by two porous plates under an oblique magnetic field and variable thermal conductivity is formulated as a boundary-value problem (BVP). The BVP is analytically solved with the homotopy analysis method (HAM). The result shows that the concentration of the nanoparticles is independent of the volume fraction of TiO₂ nanoparticles, the magnetic field intensity, and the angle. It is inversely proportional to the mass diffusivity. The fluid speed decreases whereas the temperature increases when the volume fraction of the TiO₂ nanoparticles increases. This confirms the fact that the occurrence of the TiO₂ nanoparticles results in the increase in the thermal transfer rate. The fluid speed decreases and the temperature increases for both the pure water and the nanofluid when the magnetic field intensity and angle increase. The maximum velocity does not exist at the middle of the symmetric channel, which is in contrast to the plane-Poiseuille flow, but it deviates a little bit towards the lower plate, which absorbs the fluid with a very low suction velocity. If this suction velocity is increased, the temperature in the vicinity of the lower plate will be increased. An explicit expression for the friction factor-Reynolds number is then developed. It is shown that the Hartmann number of the nanofluid is smaller than that of pure water, while the Nusselt number of the nanofluid is larger than that of pure water. However, both the parameters increase if the magnetic field intensity increases.     

Combined heat and mass transfer by mixed convection MHD flow along a porous plate with chemical reaction in presence of heat source

An exact and a numerical solutions to the problem of a steady mixed convective MHD flow of an incompressible viscous electrically conducting fluid past an infinite vertical porous plate with combined heat and mass transfer are presented.A uniform magnetic field is assumed to be applied transversely to the direction of the flow with the consideration of the induced magnetic field with viscous and magnetic dissipations of energy.The porous plate is subjected to a constant suction velocity as well as a uniform mixed stream velocity.The governing equations are solved by the perturbation technique and a numerical method.The analytical expressions for the velocity field,the temperature field,the induced magnetic field,the skin-friction,and the rate of heat transfer at the plate are obtained.The numerical results are demonstrated graphically for various values of the parameters involved in the problem.The effects of the Hartmann number,the chemical reaction parameter,the magnetic Prandtl number,and the other parameters involved in the velocity field,the temperature field,the concentration field,and the induced magnetic field from the plate to the fluid are discussed.An increase in the heat source/sink or the Eckert number is found to strongly enhance the fluid velocity values.The induced magnetic field along the x-direction increases with the increase in the Hartmann number,the magnetic Prandtl number,the heat source/sink,and the viscous dissipation.It is found that the flow velocity,the fluid temperature,and the induced magnetic field decrease with the increase in the destructive chemical reaction.Applications of the study arise in the thermal plasma reactor modelling,the electromagnetic induction,the magnetohydrodynamic transport phenomena in chromatographic systems,and the magnetic field control of materials processing.     

MHD mixed convection stagnation-point flow of a nanofluid over a vertical permeable surface: a comprehensive report of dual solutions

The steady laminar magnetohydrodynamic mixed convection boundary layer flow of a nanofluid near the stagnation-point on a vertical permeable plate with prescribed external flow and surface temperature is investigated in this study. Here, both assisting and opposing flows are considered and studied. Using appropriate similarity variables, the governing equations are transformed into nonlinear ordinary differential equations in the dimensionless stream function, which is solved numerically using the Runge–Kutta scheme coupled with a conventional shooting procedure. Three different types of nanoparticles, namely copper Cu, alumina Al₂O₃ and titania TiO₂ with water as the base fluid are considered. Numerical results are obtained for the skin-friction coefficient and Nusselt number as well as for the velocity and temperature profiles for some values of the governing parameters, namely, the volume fraction of nanoparticles ?, permeability parameter f _o , magnetic parameter M and mixed convection parameter λ. It is found that dual solutions exist for both assisting and opposing flows, and the range of the mixed convection parameter for which the solution exists, increases with suction, magnetic field and volume fraction of nanoparticles.     

Steady laminar mixed convection stagnation-point flow of a nanofluid over a vertical permeable surface in the presence of a magnetic field

A similarity solution for a steady laminar mixed convection boundary layer flow of a nanofluid near the stagnation point on a vertical permeable plate with a magnetic field and a buoyancy force is obtained by solving a system of nonlinear ordinary differential equations. These equations are solved analytically by using a new kind of a powerful analytic technique for nonlinear problems, namely, the homotopy analysis method (HAM). Three different types of nanoparticles, namely, copper (Cu), alumina (Al₂O₃), and titanium oxide (TiO₂), with water as the base fluid are considered. The influence of the volume fraction of nanoparticles, permeability parameter, magnetic parameter, and mixed convection parameter on the surface shear stress and surface heat transfer, as well as on the velocity and temperature profiles, is considered. It is observed that the skin friction coefficient and the local Nusselt number increase with the nanoparticle volume fraction for all types of nanoparticles considered in this study. The greatest values of the skin friction coefficient and the local Nusselt number are obtained for Cu nanoparticles.     

Analytical considerations of flow/thermal coupling of nanofluids in foam metals with local thermal non-equilibrium (LTNE) phenomena and inhomogeneous nanoparticle distribution

Foam metals with micro pores own excellent thermal performance, however, poor heat conductive ability of most heat-transfer fluids restricts further heat transfer improvement. Combination of foam metal and nanofluid with highly conductive nanoparticles is a promising solution. Convective thermal characteristics of nanofluids in porous foams are theoretically investigated in this work. Effects of Brownian motion and thermophoretic diffusion of nanoparticles in the base fluid on thermal performance are considered. The nanoparticle and the base-fluid are considered to be in thermal equilibrium and the temperature difference between the nanofluid and foam ligaments is especially considered. Compared with the base-fluid flow in a duct, the velocity distribution for the nanofluid flow in a porous foam is more uniform with a decreased dimensionless temperature. The pressure drop of the nanofluid increases with an increase in the concentration of the nanoparticles. By employing foam metals and nanofluid, the cross-sectional temperature becomes closer to the wall temperature. Simultaneously, notable difference between solid and fluid temperatures can be observed, revealing the LTNE effect of the nanofluid on the porous foam. It is found that the Nusselt number first increases and then decreases with an increase in nanoparticle concentration. Furthermore, the Nusselt number decreases with an increase in the foam porosity. It is found that the thermal performance of a nanofluid in a plain tube is different from that in the foam metals.     

Laminar flow through channels with porous walls and with an applied transverse magnetic field

Summary The problem of two-dimensional steady laminar flow of a viscous incompressible and electrically conducting fluid through a channel with two equally porous walls in the presence of a transverse magnetic field has been extended to include all values of Hartmann number and small suction velocity at the walls. Expressions for the velocity components, the pressure and the wall friction in terms of the Hartmann number and the suction Reynolds number are given. It is found that the pressure drop in the major flow direction and the wall friction decrease with the increase in suction and increase with the increase in the strength of the magnetic field.     

Numerical simulation of heat transfer in a micro channel heat sinks using nanofluids

In this study, a numerical simulation of copper microchannel heatsink (MCHS) using nanofluids as coolants is presented. The nanofluid is a mixture of pure water and nanoscale metallic or nonmetallic particles with various volume fractions. Also, the effects of various volume fractions, volumetric flow rate and various materials of nanoparticles on the performance of MCHS have been developed. A three-dimensional computational fluid dynamics model was developed using the commercial software package FLUENT, to investigate the conjugate fluid flow and heat transfer phenomena in micro channel heatsinks. The results show that the cooling performance of a microchannel heat sink with water based nanofluid containing Al₂O₃ (vol 8%) is enhanced by about 4.5% compared with micro channel heatsink with pure water. Nanofluids reduce both the thermal resistance and the temperature difference between the top (heated) surface of the MCHS and inlet nanofluid compared with that pure water. The cooling performance of a micro channel heat sink with metal nanofluids improves compared with that of a micro channel heat sink with oxide metal nanofluids because the thermal conductivity of metal nanofluid is higher than oxide metal nanofluids. Micro channel heat sinks with nanofluids are expected to be good candidates as the next generation cooling devices for removing ultra high heat flux.     

Comparative numerical study of single and two-phase models of nanofluid heat transfer in wavy channel

The main purpose of this study is to survey numerically comparison of two- phase and single phase of heat transfer and flow field of copper-water nanofluid in a wavy channel. The computational fluid dynamics （CFD） prediction is used for heat transfer and flow prediction of the single phase and three different two-phase models （mixture, volume of fluid （VOF）, and Eulerian）. The heat transfer coefficient, temperature, and velocity distributions are investigated. The results show that the differences between the temperature fie].d in the single phase and two-phase models are greater than those in the hydrodynamic tleld. Also, it is found that the heat transfer coefficient predicted by the single phase model is enhanced by increasing the volume fraction of nanoparticles for all Reynolds numbers; while for the two-phase models, when the Reynolds number is low, increasing the volume fraction of nanoparticles will enhance the heat transfer coefficient in the front and the middle of the wavy channel, but gradually decrease along the wavy channel.     

Forced convective flow and heat transfer over a?porous plate in a?Darcy-Forchheimer porous medium in presence of?radiation

A mathematical model is presented for analyzing the boundary layer forced convective flow and heat transfer of an incompressible fluid past a plate embedded in a Darcy-Forchheimer porous medium. Thermal radiation term is considered in the energy equation. The similarity solutions for the problem are obtained and the reduced nonlinear ordinary differential equations are solved numerically. It is noticed that the boundary layer decreases with an increase in the value of inertial parameter and in this case the temperature profile is found to decrease smoothly within the boundary layer. In case of porous plate, fluid velocity increases whereas non-dimensional temperature decreases for increasing values of suction parameter. The rate of heat transfer increases with the increasing values of Prandtl number. The effect of thermal radiation on temperature field is also analyzed.     

Radiation effect on forced convective flow and heat transfer over a porous plate in a porous medium

Heat transfer analysis has been presented for the boundary layer forced convective flow of an incompressible fluid past a plate embedded in a porous medium. The similarity solutions for the problem are obtained and the reduced nonlinear ordinary differential equations are solved numerically. In case of porous plate, fluid velocity increases for increasing values of suction parameter whereas due to injection, fluid velocity is noticed to decrease. The non-dimensional temperature increases with the increasing values of injection parameter. A novel result of this investigation is that the flow separation occurred due to suction/injection may be controlled by increasing the permeability parameter of the medium. The effect of thermal radiation on temperature field is also analyzed.     

The unsteady hydromagnetic thermal boundary layer with suction

The unsteady two-dimensional laminar flow of a viscous incompressible and electrically conducting fluid near an oscillating porous plate in the presence of uniform suction, is investigated. The solutions for the velocity, magnetic field, electric current density, temperature and Nusselt number are given in a closed form for the case of the magnetic Prandtl number being equal to unity. The other significant constants are the Eckert number, the fluid Prandtl number and the frequency of oscillation. The influence of these parametres on the solutions is given in both tabulated and graphical forms.     

Influence of induced magnetic field on the peristaltic flow of nanofluid

This article investigates the effects of an induced magnetic field on the mixed convection peristaltic motion of nanofluid in a vertical channel. Transport equations involve the combined effects of Brownian motion and thermophoretic diffusion of nanoparticles. Analysis has been addressed subject to long wavelength and low Reynolds number assumptions. Explicit expressions of stream function, magnetic force function, temperature and nanoparticles concentration are developed. Analytic expressions are validated with the obtained numerical solutions. Peristaltic pumping rate is found to increase upon increasing the strengths of electric and magnetic fields and the buoyancy force due to temperature gradient. Moreover temperature rises and nanoparticles concentration decreases with an intensification in the Brownian motion effect.     

Nanofluid flow and heat transfer due to a stretching cylinder in the presence of magnetic field

In this paper, flow and heat transfer of a nanofluid over a stretching cylinder in the presence of magnetic field has been investigated. The governing partial differential equations with the corresponding boundary conditions are reduced to a set of ordinary differential equations with the appropriate boundary conditions using similarity transformation, which is then solved numerically by the fourth order Runge–Kutta integration scheme featuring a shooting technique. Different types of nanoparticles as copper (Cu), silver (Ag), alumina (Al₂O₃) and titanium oxide (TiO₂) with water as their base fluid has been considered. The influence of significant parameters such as nanoparticle volume fraction, nanofluids type, magnetic parameter and Reynolds number on the flow and heat transfer characteristics is discussed. It was found that the Nusselt number increases as each of Reynolds number or nanoparticles volume fraction increase, but it decreases as magnetic parameter increase. Also it can be found that choosing copper (for small of magnetic parameter) and alumina (for large values of magnetic parameter) leads to the highest cooling performance for this problem.     

Dual solutions of time-dependent magnetohydrodynamic stagnation point boundary layer micropolar nanofluid flow over shrinking/stretching surface

Time-dependent, two-dimensional(2 D) magnetohydrodynamic(MHD)micropolar nanomaterial flow over a shrinking/stretching surface near the stagnant point is considered. Mass and heat transfer characteristics are incorporated in the problem. A model of the partial differential expressions is altered into the forms of the ordinary differential equations via similarity transformations. The obtained equations are numerically solved by a shooting scheme in the MAPLE software. Dual solutions are observed at different values of the specified physical parameters. The stability of first and second solutions is examined through the stability analysis process. This analysis interprets that the first solution is stabilized and physically feasible while the second one is un-stable and not feasible. Furthermore, the natures of various physical factors on the drag force, skin-friction factor, and rate of mass and heat transfer are determined and interpreted. The micropolar nanofluid velocity declines with a rise in the suction and magnetic parameters, whereas it increases by increasing the unsteadiness parameter.The temperature of the micropolar nanofluid rises with increase in the Brownian motion,radiation, thermophoresis, unsteady and magnetic parameters, but it decreases against an increment in the thermal slip constraint and Prandtl number. The concentration of nanoparticles reduces against the augmented Schmidt number and Brownian movement values but rises for incremented thermophoresis parameter values.     

Effects of suction or blowing on the velocity and temperature distribution in the flow past a porous flat plate of a power-law fluid

An analysis is made of the steady flow of a non-Newtonian fluid past an infinite porous flat plate subject to suction or blowing. The incompressible fluid obeys Ostwald-de Waele power-law model. It is shown that steady solutions for velocity distribution exist only for a pseudoplastic (shear-thinning) fluid for which the power-law index n satisfies 0<n<1 provided that there is suction at the plate. Velocity at a point is found to increase with increase in n. No steady solution for velocity distribution exists when there is blowing at the plate. The solution of the energy equation governing temperature distribution in the flow of a pseudoplastic fluid past an infinite porous plate subject to uniform suction reveals that temperature at a given point near the plate increases with n but further away, temperature decreases with increase in n. A novel result of the analysis is that both the skin-friction and the heat flux at the plate are independent of n.     

Entropy analysis of unsteady magneto-nanofluid flow past accelerating stretching sheet with convective boundary condition

The unsteady laminar magnetohydrodynamics(MHD) boundary layer flow and heat transfer of nanofluids over an accelerating convectively heated stretching sheet are numerically studied in the presence of a transverse magnetic field with heat source/sink. The unsteady governing equations are solved by a shooting method with the Runge-KuttaFehlberg scheme. Three different types of water based nanofluids, containing copper, aluminium oxide, and titanium dioxide, are taken into consideration. The effects of the pertinent parameters on the fluid velocity, the temperature, the entropy generation number, the Bejan number, the shear stress, and the heat transfer rate at the sheet surface are graphically and quantitatively discussed in detail. A comparison of the entropy generation due to the heat transfer and the fluid friction is made with the help of the Bejan number. It is observed that the presence of the metallic nanoparticles creates more entropy in the nanofluid flow than in the regular fluid flow.     

Flow and heat transfer of an electrically conducting third grade fluid past an infinite plate with partial slip

The effects of partial slip on the steady flow and heat transfer of an electrically conducting, incompressible, third grade fluid past a horizontal plate subject to uniform suction and blowing is investigated. Two distinct heat transfer problems are studied. In the first case, the plate is assumed to be at a higher temperature than the fluid; and in the second case, the plate is assumed to be insulated. The momentum equation is characterized by a highly nonlinear boundary value problem in which the order of the differential equation exceeds the number of available boundary conditions. Numerical solutions for the governing nonlinear equations are obtained over the entire range of physical parameters. The effects of slip, magnetic parameter, non-Newtonian fluid characteristics on the velocity and temperature fields are discussed in detail and shown graphically. It is interesting to find that the velocity and the thermal boundary layers decrease with an increase in the slip, and as the slip increases to infinity, the flow behaves as though it were inviscid.     

Effects of radiation in an optically thin gray gas flowing past a vertical infinite plate in the presence of a magnetic field

This paper studies the two dimensional flow of an electrically conducting fluid which is an optically thin gray gas past a stationary vertical infinite plate in the presence of radiation. It is assumed that the temperature of the plate and the suction at the plate are constant. The presence of the induced magnetic field is also taken into account. Numerical solutions for the velocity and the induced magnetic field are derived and the effects of the radiation parameter are discussed.     

Fluctuating flow of an elastico-viscous fluid along an infinite porous plate with an applied magnetic field

The problem of oscillating free stream flow of an elastico-viscous, incompressible, and electrically conducting fluid along an infinite plate with suction varying periodically with time, is considered in the presence of a transverse magnetic field. The effect of the elasticity of the fluid, the magnetic fluid, and the fluctuation of suction velocity on the velocity and the skin friction is examined.     

Lattice Boltzmann simulation of heat transfer and fluid flow in a microchannel with nanofluids

Mathematical modeling is performed to simulate forced convection flow of 47 nm- Al₂O₃/water nanofluids in a microchannel using the lattice Boltzmann method (LBM). Single channel flow and conjugate heat transfer problem are taken into consideration and the heat transfer rate using a nanofluid is examined. Simulations are conducted at low Reynolds numbers (2 ≤ Re ≤ 16). The computed average Nusselt number, which is associated with the thermal conductivity of nanofluid, is in the range of 0.6 ￡ [`(Nu)] ￡ 13 0.6 \le \overline{Nu} \le 13 . Results indicate that the average Nusselt number increases with the increase of Reynolds number and particle volume concentration. The fluid temperature distribution is more uniform with the use of nanofluid than that of pure water. Furthermore, great deviations of computed Nusselt numbers using different models associated with the physical properties of a nanofluid are revealed. The results of LBM agree well with the classical CFD method for predictions of flow and heat transfer in a single channel and a microchannel heat sink concerning the conjugate heat transfer problem, and consequently LBM is robust and promising for practical applications.