Atomic-absorption spectrophotometric determination of ultramicro amounts of selenium(IV) and total selenium in sulphuric acid

Summary Ultramicro amounts of selenium in sulphuric acid are determined by a new atomic absorption spectrophotometric method. Selenium(IV) is directly determined ater extraction into toluene with an aromatic o-diamine and addition of nickel(II) prior to atomization; the determination of total selenium (0, IV and VI) needs a treatment of the sample with selected oxidizing and reducing agents.In the studied samples, total selenium (0.003–0.022 g of Se in 1 ml sulphuric acid) is present only in the tetravalent state. The detection limit of the method is 0.003 g of selenium.

---

Atomabsorptions-spektralphotometrische Bestimmung von Ultramikromengen Selen(IV) und Gesamtselen in Schwefelsäure

Zusammenfassung Selen(IV) kann direkt bestimmt werden nach Toluolextraktion der mit einem aromatischen o-Diamin behandelten Lösung und Zusatz von Nickel(II). Die Bestimmung von Gesamtselen (0, IV, VI) erfordert eine Vorbehandlung mit Perchlor- bzw. Salpetersäure und Wasserstoffperoxid. Die Nachweisgrenze des Verfahrens beträgt 0,003 g Se. In den untersuchten Proben war das Gesamtselen (0,003–0,022 g/ml) nur als Se(IV) vorhanden.

     

Indirect spectrophotometric determination of cerium(IV)

A simple and very fast photometric method for the determination of trace levels of cerium(IV) has been developed. Use has been made of the reaction in which iron (II), on oxidation with cerium(IV), gives iron(III) which is complexed with tiron, in acidic medium, to form a stable blue color, the intensity of which is in direct proportion to the amount of cerium(IV) originally present in the sample solution. In addition, the method has a wide range of determination and reasonable sensitivity, and it avoids both temperature control and the tedious extraction step.     

Indirect determination of arsenic by flotation spectrophotometry

An indirect method of arsenic determination in the submicrogram range via the determination of molybdenum is presented here. High sensitivity is achieved by combination of the chemical amplification during formation of dodecamolybdoarsenic acid (arsenic: molybdenum ratio 1 12) with multiplication due to the formation of ion-association complexes during flotation-spectrophotometric molybdenum determination with crystal violet (molar ratio 1 2). Thus, the amplification factor relating to arsenic is 24.Dodecamolybdoarsenic acid is formed in a weakly acidic medium and is quantitatively extracted byn-butanol. Back extraction of the heteropoly acid to the aqueous phase and its simultaneous destruction provides the basis for the reaction of released molybdate ions with thiocyanate ions. The molybdenum-thiocyanate complex forms a sparingly soluble ion-association complex with crystal violet which can be floated with toluene on the phase boundary (film flotation). After separation of the aqueous phase the floated molybdenum compound is dissolved in acetone and the resulting free crystal violet ions are subjected to photometric determination at 590 nm as equivalent of the concentration of arsenic. The molar absorptivity of crystal violet is 3.2 · 10⁵1 · mol^–1 · cm^–1. Beer's law is obeyed in a concentration range from 0.01 to 1 g Mo · ml^–1 (0.001–0.1 g As · ml^–1). The resulting detection limit for arsenic is 1 ng · ml^–1.     

Synergic extraction and spectrophotometric determination of titanium(IV)

A method has been developed for the synergic extraction and spectrophotometric determination of Ti(IV) with N-hydroxy-NN'-diphenylbenzamidine and thiocyanate. The yellow ternary complex, extracted into chloroform from dilute sulphuric acid medium (pH = 1.5+/-0.1), has maximum absorbance at 390 nm (molar absorptivity 1.3 x 1O(4) 1.mole(-1). cm(-1)). The method is free from interference from a large number of foreign ions and is recommended for the determination of titanium in steel.     

Solid-phase spectrophotometric iodometric determination of nitrite and selenium(IV) using a polymethacrylate matrix

Procedures for the iodometric solid-phase spectrophotometric determination of nitrite and selenium( IV) using a polymethacrylate matrix are proposed. The procedures are based on the reaction of nitrite and selenium(IV) with iodine in an acidic medium with the release of free iodine in amounts equivalent to those of the substances to be determined, extraction of the iodine formed with a polymethacrylate matrix, and measurement of absorbance of the matrix at 370 nm. The developed procedures ensure the determination of 0.01–0.12 mg/L of nitrite and 0.05–0.40 mg/L of selenium(IV) with limits of detection of 0.005 and 0.03 mg/L, respectively. It was shown that the proposed procedures can be applied to the determination of selenium(IV) in mineral water and nitrites in vegetables and soil.     

Kinetic spectrophotometric determination of trace amounts of selenium and vanadium

A sensitive kinetic spectrophotometric method has been developed for the determination of Se(IV) over the range of 45 to 4000 ng in 10 mL of solution. The method is based on the catalytic effect of Se(IV) on the reduction reaction of bromate by hydrazinium dichloride, with subsequent reaction of Ponceau S with products of the above reaction (chlorine and bromine), causing color changing of Ponceau S. Method development includes optimization of time interval for measurement of slope, pH, reagents concentration, and temperature. The optimized conditions yielded a theoretical detection limit of 33 ng/?10 mL of solution of Se(IV). The interfering effects were studied and removed. The method was applied to the determination of selenium in spiked water, Kjeldahl tablet, selenium tablet, and shampoo. Vanadium(V) has an inhibition effect on the catalyzed reaction of bromate and hydrazine by selenium. Using this effect, V(V) can be determined in the range of 70 to 2500 ng in 10 mL of solution. The optimization procedure includes pH and selenium concentration. An extraction method was used for interference removal. The method was applied to the determination of vanadium in petroleum. Received: 20 October 1998 / Revised: 17 April 1999 / Accepted: 3 June 1999     

Kinetic spectrophotometric determination of trace amounts of selenium and vanadium

A sensitive kinetic spectrophotometric method has been developed for the determination of Se(IV) over the range of 45 to 4000 ng in 10 mL of solution. The method is based on the catalytic effect of Se(IV) on the reduction reaction of bromate by hydrazinium dichloride, with subsequent reaction of Ponceau S with products of the above reaction (chlorine and bromine), causing color changing of Ponceau S. Method development includes optimization of time interval for measurement of slope, pH, reagents concentration, and temperature. The optimized conditions yielded a theoretical detection limit of 33 ng/¶10 mL of solution of Se(IV). The interfering effects were studied and removed. The method was applied to the determination of selenium in spiked water, Kjeldahl tablet, selenium tablet, and shampoo. Vanadium(V) has an inhibition effect on the catalyzed reaction of bromate and hydrazine by selenium. Using this effect, V(V) can be determined in the range of 70 to 2500 ng in 10 mL of solution. The optimization procedure includes pH and selenium concentration. An extraction method was used for interference removal. The method was applied to the determination of vanadium in petroleum.     

Rapid extraction and spectrophotometric determination of vanadium(IV) with thiothenoyltrifluoroacetone

Thiothenoyltrifluoroacetone in carbon tetrachloride-butanol (1:1) is used for extraction and spectrophotometric determination of vanadium (IV) at pH 4.5-5. The greenish-yellow complex is measured spectrophotometrically at 450 nm. The system conforms to Beer's law over the range 2-11 mug/ml of extract. The colour of the complex is stable for at least 80 hr. Vanadium (IV) was quantitatively extracted and determined in the presence of 120:1 w/w ratios of various ions. The method was made selective by using common sequestering agents or prior extraction with tributyl phosphate, diethylammonium diethyldithiocarbamate, alpha-furildioxime or acetylacetone. The method is rapid, simple, selective and sensitive.     

Determination of arsenic(III), arsenic(V), antimony(III), antimony(V), selenium(IV) and selenium(VI) by extraction with ammonium pyrrolidinedithiocarbamate—methyl isobutyl ketone and electrothermal atomic absorption spectrometry

The solution conditions and other parameters affecting the ammonium pyrrolidine-dithiocarbamate—methyl isobutyl ketone extraction system for graphite-furnace atomic absorption spectrometric determination of As(III), As(V), Sb(III), Sb(V), Se(IV) and Se(VI) were studied in detail. The solution conditions for the single or simultaneous extraction of As(III), Sb(III) and Se(IV) were not critical. Arsenic(V) and Se(VI) were not extracted over the entire range of pH and acidity studied. Antimony(V) was extracted only in the acidity range 0.3—1.0 M HCl. Simultaneous extraction of total arsenic and total antimony was possible after reduction of As(V) with thiosulphate. Interference studies are also reported.     

Ternary complexes in the spectrophotometric determination of trace amounts of platinum(IV)

A simple, rapid, reproducible, sensitive and selective method is proposed for the spectrophotometric determination of submicrogram amounts of platinum(IV) in aqueous media. The proposed method involves the formation of a ternary complex between the hexa-ammine-platinum(IV) cationic complex, and the counter-ion 2,4,5,7-tetrabromofluorescein ethyl ester. The reaction is instantaneous and the red ternary complex remains stable for ca. 1 hr. Beer's law is obeyed over the range 39-1170 ppM with molar absorptivity of ca. 8.0 x 10(4) at 555 nm and pH 10. A relative standard deviation of 1.1% was found for the reproducibility of the method. Even without the use of masking agents, no interference is encountered from other noble metals except rhodium(III). Of 13 other cations and 8 anions tested, only iron(III) interferes.     

Rapid and simple chromatographic separation of V(V) and V(IV) using KH-phthalate and their determination by flame atomic absorption spectrometry

A method was developed for the chromatographic separation of V(V) and V(IV) based on the different sorption forces of these vanadium species in C18 columns in presence of KH-phthalate. The vanadium species were detected with a flame atomic absorption spectrometer with acetylene/N₂O flame. The detection limits (3σ) of V(V) and V(IV) were 0.18 μg/mL and 0.15 μg/mL, respectively. The relative standard deviations (N = 5) are 4.2% and 3.4% for 20–20 μg/mL V(V) and V(IV), respectively. The sampling frequency is 75/h. Because of the special interaction occurring between phthalate and V(IV) on the C18 column and the acetylene/N₂O flame atomic absorption detection, practically no interferences can be detected even in large inorganic matrix. Received: 20 February 1997 / Revised: 2 June 1997 / Accepted: 7 June 1997     

Rapid and simple chromatographic separation of V(V) and V(IV) using KH-phthalate and their determination by flame atomic absorption spectrometry

A method was developed for the chromatographic separation of V(V) and V(IV) based on the different sorption forces of these vanadium species in C18 columns in presence of KH-phthalate. The vanadium species were detected with a flame atomic absorption spectrometer with acetylene/N₂O flame. The detection limits (3σ) of V(V) and V(IV) were 0.18 μg/mL and 0.15 μg/mL, respectively. The relative standard deviations (N = 5) are 4.2% and 3.4% for 20–20 μg/mL V(V) and V(IV), respectively. The sampling frequency is 75/h. Because of the special interaction occurring between phthalate and V(IV) on the C18 column and the acetylene/N₂O flame atomic absorption detection, practically no interferences can be detected even in large inorganic matrix.     

Selective extraction and spectrophotometric determination of titanium(IV) with 2-thenoyltrifluoroacetone

A new rapid method is suggested for simultaneous extraction and spectrophotometric determination of titanium with 2-thenoyltrifluoroacetone (TTA). The greenish-yellow chelate of titanium(IV)-TTA can be extracted with isoamvl alcohol-benzene and measured at 430 mm. The extraction can be carried out in presence of Al, Cr(III), Th, Zr, Mo, W, borate, phosphate, citrate, tartrate and EDTA.     

Indirect spectrophotometric determination of chromium(VI)

A new simple and sensitive spectrophotometric method for the determination of chromium(VI) is established. It relies upon the oxidation of iron(II) with the titled ion, in acidic medium, to form iron(III) which is complexed with tiron to form a stable blue color with maximum absorption at 650 nm. Adherence to Beer's law is observed in the range 10–100 μg of chromium(VI) per 25 ml, with a molar absorptivity of 5.6 × 10³ liters mol^?1 cm^?1, sensitivity index of 0.0093 μg cm^?1, relative error of ?5.0 to +0.3%, and relative standard deviation of 0.3–4.0%, depending on the concentration level. Furthermore, the reaction needs neither temperature control nor an extraction step.     

Extraction spectrophotometric determination of selenium(IV) with J acid in environmental samples

A new simple and sensitive method for the extraction and spectrophotometric determination of selenium(IV) is described. Selenium(IV) is reacted with J acid (6-ANSA) to form a butanol extractable complex with maximum absorbance of 520 nm. Beer's law is obeyed in the range of 0.03-0.3 mg/l. of selenium. Molar absorptivity and Sandell's sensitivity are found to be 18.5 +/- (0.1) x 10(3) l. mol(-1). cm(-1) and 0.004 microg/cm(2), respectively. The analytical parameters were optimized and the method applied for the determination of selenium in polluted water, soil, dust, hair and plant materials. The method is compared with other reported methods and found to be superior to many of the reported methods.     

Flow injection kinetic spectrophotometric determination of trace amounts of Se(IV) in seawater

A simple, accurate, sensitive and selective flow injection catalytic kinetic spectrophotometric method for rapid determination of trace amounts of selenium is proposed in this paper. The proposed method is based on the accelerating effect of Se(IV) on the reaction of ethexlenediamine tetrecetic acid disodium salt (EDTA) and sodium nitrate with ammonium iron(II) sulfate hexahydrate in acidic media. The absorbance intensity was registered in this reaction solution at 440 nm. The calibration graph is linear in the range of 5 × 10⁻⁹-2 × 10⁻⁷ and 2 × 10⁻⁷-2 × 10⁻⁶ g ml⁻¹. The detection limit is 2 × 10⁻⁹ g ml⁻¹. The relative standard deviation was 3.4% for 5 × 10⁻⁸ g ml⁻¹ Se(IV) (n = 11), 2.7% for 5 × 10⁻⁷ g ml⁻¹ Se(IV) (n = 11). This method is very simple, rapid and suitable for automatic and continuous analysis. The presented system has been applied successfully to determination of Se(IV) of seawater samples.     

Indirect spectrophotometric determination of chloride by solvent extraction as tris(1,10-phenanthroline)iron(II) thiocyanate

An indirect spectrophotometric method for the determination of small amounts of chloride in fresh waters is described. Chloride ions react with mercury(II) thiocyanate to liberate thiocyanate ions, which can be selectively extracted into nitrobenzene with tris(1,10-phenanthroline)iron(II) chelate cations. The red color (516 nm) of the organic phase measured against a reagent blank is proportional to the initial concentration of chloride ions in the aqueous phase. At least an equimolar amount of tris(1,10-phenanthroline)iron(II) chelate and a 3-fold amount of mercury(II) thiocyanate are needed; the optimal pH range is 1.5–3.5. Beer's law is obeyed over the concentration range of 0.8–5.6 10^-5 M of chloride. The color stability and the apparent sensitivity are better than those of the mercury(II) thiocyanate-iron(III) method. Large amounts of sulphate, phosphate, fluoride, carbonate, acetate, potassium, sodium, and ammonium ions had negligible or no effect ; bromide, iodide, cyanide, sulphide, and thiocyanate interfere.     

Preconcentration and determination of ultra trace amounts of arsenic(III) and arsenic(V) in tap water and total arsenic in biological samples by cloud point extraction and electrothermal atomic absorption spectrometry

A new approach for developing a cloud point extraction-electrothermal atomic absorption spectrometry has been described and used for determination of arsenic. The method is based on phase separation phenomenon of non-ionic surfactants in aqueous solutions. After reaction of As(V) with molybdate towards a yellow heteropoly acid complex in sulfuric acid medium and increasing the temperature to 55 °C, analytes are quantitatively extracted to the non-ionic surfactant-rich phase (Triton X-114) after centrifugation.To decrease the viscosity of the extract and to allow its pipetting by the autosampler, 100 μl methanol was added to the surfactant-rich phase. An amount of 20 μl of this solution plus 10 μl of 0.1% m/v Pd(NO₃)₂ were injected into the graphite tube and the analyte determined by electrothermal atomic absorption spectrometry.Total inorganic arsenic(III, V) was extracted similarly after oxidation of As(III) to As(V) with KMnO₄. As(III) was calculated by difference. After optimization of the extraction condition and the instrumental parameters, a detection limit (3σ_B) of 0.01 μg l⁻¹ with enrichment factor of 52.5 was achieved for only 10 ml of sample. The analytical curve was linear in the concentration range of 0.02-0.35 μg l⁻¹. Relative standard deviations were lower than 5%. The method was successfully applied to the determination of As(III) and As(V) in tap water and total arsenic in biological samples (hair and nail).