A note on vibration of a cantilever plate immersed in water

The added mass of the fluid surrounding it plats an important role in the dynamic behaviour of a submerged structure. The first few mode shapes and the respective natural frequencies of a submerged cantilever plate are found by using a finite element procedure, eigenvalues being obtained by a simultaneous iteration technique. The influence of the water depth below the plate and also of the water's lateral extent is considered, in order to test the convergency of the results. Results on the effects of the depth of immersion on the natural frequencies and mode shapes of the cantilever plate for different aspect ratios are presented.     

On the influence of a horizontal magnetic field on the Rosensweig instability of a nonlinear magnetizable ferrofluid

The Rosensweig instability induced by magnetic forces of the flat free surface of the layer of a stationary nonlinearly magnetizable ferrofluid is considered. The fluid covers a horizontal plate of a nonmagnetic material, located in a tilted magnetic field. The critical value of the vertical component of the magnetization vector is calculated in the linear formulation for a deep magnetic fluid for any physically admissible magnetization law. The influence of the horizontal component of the applied magnetic field on the onset of instability upon the modified Langevin magnetization is analyzed.     

Resonance analysis of a 2D alluvial valley subjected to seismic waves

The T-matrix formalism and an ultrasonic experiment are developed to study the scattering of in-plane waves for an alluvial valley embedded in a two-dimensional half-space. The solution of the in-plane scattering problem can be determined by the T-matrix method, where the basis functions are defined by the singular solutions of Lamb's problems with surface loading in both horizontal and vertical directions. In the experiment, a thin steel plate with a semicircular aluminum plate attached on the edge is used to simulate the two-dimensional alluvial valley in the state of plane stress. Based on the spectra of displacement signals measured at the free edge of the scatterer, the resonance frequencies where the peaks appear can be identified. It can be shown that the nondimensional resonance frequency is one of the characteristic properties of the scattering system. Furthermore, it is noted that the nondimensional resonance frequencies measured experimentally are in good agreement with those calculated theoretically.     

部分浸没圆柱壳声固耦合计算的半解析法研究

部分浸没圆柱壳-流场耦合系统的声振分析是一种典型的半空间域内声固耦合问题,其振动及声学计算目前主要依赖于数值方法求解,但无论从检验数值法还是从机理上揭示其声固耦合特性,解析或半解析方法的发展都是不可或缺的.本文提出了一种半解析方法,先将声场坐标系建立在自由液面上,采用正弦三角级数来满足自由液面上的声压释放边界条件;接着基于二维Flügge薄壳理论建立了以圆柱圆心为坐标原点的壳-液耦合系统的控制方程;然后再利用Galerkin法处理声固耦合界面的速度连续条件,推导得到声压幅值与壳体位移幅值之间的关系矩阵并求解该耦合系统的振动和水下声辐射.与有限元软件Comsol进行了耦合系统自由、受迫振动和水下辐射噪声计算结的对比分析,表明本文方法准确可靠.本文的研究为解析求解弹性结构与声场部分耦合的声振问题提供了新的思路.     

Resonant Response of Rectangular/kFM Cantilever in Liquid

Dynamic characteristics of atomic force microscopy （AFM） cantilevers can be influenced by their working media. We perform an experimental study on the resonant responses of rectangular AFM cantilevers with different sizes immersed in various viscous fluids. The measured resonance frequencies in liquids are used to valldate several theoretical models. Comparison shows the analytical model proposed by Sader [J. Appl. Phys. 84 （1998） 64] can give the best agreement with the experimental results with the maximum relative error nearly 16% for all the cantilevers in different liquids. The ratio between the resonant frequencies in air and water is almost independent of the cantilever length, which is consistent with the theoretical analyses.     

Coupled vibrations of cantilever cylindrical shells partially submerged in fluids with continuous, simply connected and non-convex domain

The approach developed in the present paper is applied for the coupled-vibration analysis of a cantilever cylindrical shell partially submerged in a fluid with a continuous, simply connected and non-convex domain. The shell is partially and concentrically submerged in a rigid cylindrical container partially filled by a fluid which is assumed to be incompressible and inviscid. The velocity potential for fluid motion is formulated in terms of eigenfunction expansions using the collocation method. The interaction between the fluid and the structure takes into account by using the compatibility requirement along the wet surface of the shell and the Rayleigh-Ritz method is used to calculate natural frequencies and modes of the coupled system. The validity of the developed theoretical method is verified by comparing the results with those obtained from the finite element analysis. Furthermore, the effects of submergence depth, radial distance between shell and container, and circumferential wavenumbers on the natural frequencies and modes of the coupled system are investigated.     

FREE VIBRATION OF A PARTIALLY LIQUID-FILLED AND SUBMERGED, HORIZONTAL CYLINDRICAL SHELL

The dynamic characteristics (i.e., natural frequencies and mode shapes) of a partially filled and/or submerged, horizontal cylindrical shell are examined. In this investigation, it is assumed that the fluid is ideal, and fluid forces are associated with inertial effects only: namely, the fluid pressure on the wetted surface of the structure is in phase with the structural acceleration. The in vacuo dynamic characteristics of the cylindrical shell are obtained using standard finite element software. In the “wet” part of the analysis, it is assumed that the shell structure preserves its in vacuo mode shapes when in contact with the contained and/or surrounding fluid and that each mode shape gives rise to a corresponding surface pressure distribution of the shell. The fluid-structure interaction effects are calculated in terms of generalized added masses, using a boundary integral equation method together with the method of images in order to impose an appropriate boundary condition on the free surface. To assess the influence of the contained and/or surrounding fluid on the dynamic behaviour of the shell structure, the wet natural frequencies and associated mode shapes were calculated and compared with available experimental measurements.     

Effect of tip mass on frequency response and sensitivity of AFM cantilever in liquid

The effect of tip mass on the frequency response and sensitivity of atomic force microscope (AFM) cantilever in the liquid environment is investigated. For this purpose, using Euler–Bernoulli beam theory and considering tip mass and hydrodynamic functions in a liquid environment, an expression for the resonance frequencies of AFM cantilever in liquid is derived. Then, based on this expression, the effect of the surface contact stiffness on the flexural mode of a rectangular AFM cantilever in fluid is investigated and compared with the case where the AFM cantilever operates in the air. The results show that in contrast with an air environment, the tip mass has no significant impact on the resonance frequency and sensitivity of the AFM cantilever in the liquid. Hence, analysis of AFM behaviour in liquid environment by neglecting the tip mass is logical.     

Frequency shifts of cantilever in AFM

The frequency shift and frequency shift image of cantilever in AFM have been studied by numerical integration of the equation of motion of cantilever for silicon tip with rutile TiO₂(0 0 1) surface in UHV conditions and by the Hamaker summation method for the tip-surface interaction forces. The effects of the excitation frequency at the cantilever base and the equilibrium position of the tip on the frequency shift have been calculated and the results showed the same phenomena as those measured, e.g., the frequency shift increased dramatically or rapidly before the contact point and was then almost level off after the contact point. The effects of scanning speed and the initial closest distance of tip to the contact point have been calculated at different excitation frequencies at the cantilever base and the results showed that proper frequency shift image could be obtained either by noncontact mode at the excitation frequency slightly less than the resonance frequency of free cantilever, or by tapping mode at the excitation frequency a few times smaller than the resonance frequency of free cantilever.     

Advanced Study of Unsteady Heat and Chemical Reaction with Ramped Wall and Slip Effect on a Viscous Fluid

This paper investigate the effect of slip boundary condition, thermal radiation, heat source, Dufour number,chemical reaction and viscous dissipation on heat and mass transfer of unsteady free convective MHD flow of a viscous fluid past through a vertical plate embedded in a porous media. Numerical results are obtained for solving the nonlinear governing momentum, energy and concentration equations with slip boundary condition, ramped wall temperature and ramped wall concentration on the surface of the vertical plate. The influence of emerging parameters on velocity,temperature and concentration fields are shown graphically.     

Dynamical response of nanomechanical oscillators in immiscible viscous fluid for in vitro biomolecular recognition

Dynamical response of nanomechanical cantilever structures immersed in a viscous fluid is important to in vitro single-molecule force spectroscopy, biomolecular recognition of disease-specific proteins, and the study of microscopic protein dynamics. Here we study the stochastic response of biofunctionalized nanomechanical cantilever beams in a viscous fluid. Using the fluctuation-dissipation theorem we derive an exact expression for the spectral density of displacement and a linear approximation for resonance frequency shift. We find that in a viscous solution the frequency shift of the nanoscale cantilever is determined by surface stress generated by biomolecular interaction with negligible contributions from mass loading due to the biomolecules.     

Development of the Rayleigh-Taylor instability in a thin layer of a magnetic fluid subjected to an orthogonal magnetic field

A thin layer of a Newtonian magnetic fluid wetting the faced-down surface of a horizontal magnetized plate in a vertical magnetic field is considered. The lower boundary of the layer is the interface with a stationary gas. The effect of magnetic forces on the development of the Rayleigh-Taylor instability is considered in the linear formulation of the long-wave approximation of ferrohydrodynamic equations.     

Influence of acoustic leakage at fluid–solid interface on interferometric detection of surface acoustic wave

When using laser interferometer to detect surface acoustic wave at fluid–solid interface, there are two factors which will cause the optical path length variation of the probe laser beam: interface deformation, and refractive index changes in fluid induced by acoustic leakage. Influence of acoustic leakage on laser interferometric detection for surface acoustic wave is researched here. A metal plate immersed in an infinite fluid is used as a physical model. Interface deformation due to laser-induced acoustic wave and pressure in fluid due to acoustic leakage are computed for select cases by finite element method. The optical path length variation caused by the two factors are calculated respectively and compared. The results show that the influence of acoustic leakage increases with the increasing acoustic impedance matching of fluid and solid, the peak-to-peak of influence degree increases linearly with the increasing acoustic impedance of fluid, and that decreasing the distance between the interferometer and interface can effectively reduce the influence of acoustic leakage.     

圆管潜射流生成偶极子涡特性实验

利用溢流恒压装置产生具有稳定出流速度的圆管潜射流, 结合染色液流态显示方法, 在多种射流无量纲潜深d/H、雷诺数Re以及限制数C的组合下, 实验研究了该潜射流动量在有限深密度均匀流体中的演化特性, 其中d为射流潜深, H为水深. 研究表明, 当C<1时潜射流表现为深水特征, 而当1≤ C<2时潜射流表现为过渡特征, 在这两种情况下均不产生任何形式的大尺度相干结构; 当2≤ C<10时潜射流表现为浅水特征, 而C≥10时潜射流表现为极浅水特征, 在这两种情况下均产生大尺度的偶极子涡结构. 对极浅水特征潜射流, 在各种无量纲潜深下, 偶极子涡结构的无量纲形成时间t_f^*与无量纲射流时间T_inj^*均满足相同的正比例关系; 对浅水特征潜射流, 当d/H=0.5时, t_f^*与T_inj^*满足某种线性关系, 但对其他无量纲潜深, t_f^*与T_inj^*之间无明显规律. 关键词： 圆管潜射流 限制数 偶极子涡结构 形成时间     

Instability and breakup of a thick layer of a viscous magnetic fluid in a tilted magnetic field

A linear partial differential equation describing the evolution of an initial disturbance of a flat free surface of a thin layer of a viscous magnetic fluid covering a horizontal plate in the presence of a uniform magnetic field, is derived within a system of ferrohydrodynamic and magnetostatic equations. The effect of magnetizing the plate on the stability of the flat free surface is investigated. An estimate is obtained for the minimum value of the tangential component of the magnetization vector of the fluid sufficient to radically alter the pattern of the final breakup of the continuous layer. Zh. Tekh. Fiz. 69, 14–22 (October 1999)     

Standing waves in an elastic layer loaded with a finite mass

Standing shear waves in a plane-parallel rubberlike layer fixed without slippage between two rigid plates with finite masses are investigated. The lower plate, which underlies the layer, oscillates in the direction parallel to its surface under an external harmonic force, whereas the upper plate freely overlies the layer. It is shown both theoretically and experimentally that such a system exhibits resonances at frequencies the values of which depend on the mass of the free plate and the shear modulus of the layer. The shapes of the resonance curves are calculated and measured for different values of parameters of the layer and different masses of the upper plate. From the measured resonance curves, it is possible to determine the dynamic shear modulus and the shear viscosity of the rubberlike material.     

Ultrasonic radiation in dynamic force microscopy

In dynamic force microscopy the cantilever of an atomic force microscope is vibrated at ultrasonic frequencies in the range of several 10 kHz up to several MHz while scanning a sample surface. The amplitude and phase of the cantilever vibration as well as the shift of the cantilever resonance frequencies provide information about local sample surface properties. In several operation modes of dynamic force microscopy, for example force modulation microscopy, tapping mode or atomic force acoustic microscopy, the sensor tip is in contact with the sample at least during a fraction of its vibration cycle. The periodic indentation of the tip with the sample surface generates ultrasonic waves. In this paper, the ultrasonic radiation of a vibrating cantilever into a sample and its contribution to the damping of the cantilever vibration are calculated. The theoretical results are compared to experiments.     

Frequencies of Lock Gate Structure Coupled with Reservoir Fluid

This study determines the natural frequencies of the lock gate structure, considering the coupled effect of reservoir fluid on one side using the finite element method (FEM). The gate is assumed to be a uniformly thick plate, and its material is isotropic, homogeneous, and elastic. The reservoir fluid is assumed to be inviscid and incompressible in an irrotational flow field. The length of the reservoir domain is truncated using the far boundary condition by adopting the Fourier series expansion theory. Two different assumptions on the free surface, i.e., undisturbed and linearized, are considered in the fluid domain analysis. The computer code is written based on the developed finite element formulations. The natural frequencies of the lock gate are computed when interacting with and without reservoir fluid. Several numerical problems are studied considering the effects of boundary conditions, aspect ratios, and varying dimensions of the gate and the fluid domain. The frequencies of gate reduce significantly due to the presence of fluid. The frequencies increase when the fluid extends to either side of the gate. The frequencies reduce when the depth of the fluid domain above the top edge of the gate increases. The frequencies drop considerably when the free surface condition is taken into account. The results of frequencies of lock gate structure may be useful to the designer if it is experienced in natural catastrophes.     

Flexural vibration insulation with an elastic layer for a plate under nonuniform vibratory action

A method is proposed for calculating the vibration insulation of an elastic layer positioned between a finite-size plate with free edges and a vibrationally active base. The elastic layer consists of a discrete set of springs. In the case of an out-of-phase vibration of the base surface, the mean dynamic action on the plate decreases, which leads to an increase in vibration insulation. By contrast, the resonances of flexural plate vibrations reduce the vibration insulation at resonance frequencies. For different cases, the system parameters that correspond to a positive effect of vibration insulation are estimated. The simplest mass-spring system possessing a single degree of freedom is discussed.     

Axisymmetric vibrations of a viscous-fluid-filled piezoelectric spherical shell and the associated radiation of sound

Axisymmetric vibrations of a viscous-fluid-filled piezoelectric sphere, with radial polarization, submerged in a compressible viscous fluid medium are investigated. The oscillations are harmonically driven by an axisymmetrically applied electric potential difference across the surface of the shell. A theoretical formulation cast the piezoelectric shell problem into a corresponding problem of an elastic shell with the contribution of piezoelectricity confined to slightly modified in vacuum natural frequencies and their associated mode shapes. It is noted that the fluid inside the shell will have a dominating influence on the vibrational characteristics of the submerged shell. The circular components of the natural frequency spectra closely follow those of the fluid-filled shell in vacuo. Furthermore, the corresponding damping components of those natural frequencies are rather small, making acoustic radiation and under-damped oscillation possible for an infinite number of natural frequencies. The characteristics of natural frequencies are elucidated using a fluid-filled polyvinglindene fluoride (PVDF) shell submerged in both air and water as an example. It is found that the piezoelectric parameters that contribute to the shell's natural frequencies is of a small order for thin PVDF shells, and is thereby negligible. It is noted that, with the mechanical constant typically associated with piezoelectric materials, fluid viscosity could have a significant effect on some vibrations. In certain cases, a natural frequency associated with a minimum viscous damping and a maximum of total damping (indicating highly efficient acoustic radiation) is possible with such a frequency.The vibrational characteristics, fluid loading, and energy flow are evaluated for a fluid-filled PVDF shell submerged in air and water. The inclusion of fluid inside the shell is shown to produce various narrow band peaks responses, vibrational absorbing frequencies, and non-dissipating frequencies. Those vibrational characteristics could have many potential applications. For example, the interior fluid could offer the option of generating a desired narrow band near resonant sound radiation while keeping power dissipation due to fluid viscosity to a minimum. Those well-defined narrow band characteristics also open up possibilities of using a vibrating, fluid-filled shell as a micro scale sensor for sensing and detection applications.