Influence of electron beam irradiation on physicochemical properties of poly(trimethylene carbonate)

Electron beam (EB) irradiation of poly(trimethylene carbonate) (PTMC), an amorphous, biodegradable polymer used in the field of biomaterials, results in predominant cross-linking and finally in the formation of gel fraction, thus enabling modification of physicochemical properties of this material without significant changes in its chemical structure. PTMC films (M_w: 167-553 kg mol⁻¹) were irradiated with different doses using an electron accelerator. Irradiation with a standard sterilization dose of 25 kGy caused neither significant changes in the chemical composition of the polymer nor significant deterioration of its mechanical properties. Changes in viscosity-, number-, weight-, and z-average molecular weights of PTMC for doses lower than the gelation dose (D_g) as well as gel-sol analysis and swelling tests for doses above D_g indicate domination of cross-linking over degradation. EB irradiation can be considered as an effective tool for increasing the average molecular weight of PTMC and sterilization of PTMC-based biomaterials.     

Influence of radiation temperature on the crosslinking of nitrile rubber by electron beam irradiation

Nitrile rubber with 18% acrylonitrile content in presence and absence of polyfunctional monomers like trimethylolpropane triacrylate (TMPTA), tripropyleneglycol diacrylate (TPGDA), tetramethylolmethane tetraacrylate (TMMT) and m-phenylene bismaleimide was subjected to electron beam irradiations at different temperatures. The structural changes with different doses of radiations were investigated with the help of FTIR spectroscopy (in the ATR mode), dynamic mechanical thermal analysis and sol–gel analysis. There was a decrease in the concentration of olefinic groups for this elastomer on radiation at high temperature as compared to the room temperature. The increase in crosslinking at elevated temperature was also revealed by the increase in % gel content and dynamic storage moduli with radiation dose. The lifetime of spurs, an important criterion for overlapping of spurs, was determined for both grafted and ungrafted nitrile rubber using a mathematical model. The ratio of scissioning to crosslinking for nitrile rubber was determined using Charlesby–Pinner equation. The mechanical properties were studied and the tensile strength was found to increase with grafting of polyfunctional monomers on irradiation at high temperature.     

Effects of electron beam irradiation on the microbial growth and quality of beef jerky during storage

Electron beam irradiation was applied to improve the microbial safety of beef jerky during storage. Beef jerky samples were irradiated at doses of 1, 3, 5, and 10 kGy and stored at 20 °C for 60 d. Microbiological data indicated that the populations of total aerobic bacteria significantly decreased with increasing irradiation dosage. In particular, the populations of total aerobic bacteria were significantly decreased by 1.76 log CFU/g at 10 kJ/m², compared to the control. Color measurements showed reduced Hunter L and a values of beef jerky for all the treatments during storage, and the Hunter L, a, and b values of beef jerky were not significantly different among the treatments. Sensory evaluation results also showed that electron beam irradiation did not affect sensory scores in overall during storage. Therefore, the results suggest that electron beam irradiation could be useful in improving the microbial safety without impairing the quality of beef jerky during storage.     

Effects of gamma and electron beam irradiation on polymer electrolytes

Polymer electrolytes based on poly(ethylene oxide) and lithium salts have been widely studied in recent years. In order to enhance the room temperature ionic conductivity of PEO-LiX complexes, various techniques, such as addition of plasticizers and crown ether, and also irradiation by γ and electron beams have been investigated. The enhancement of the conductivity by irradiation has been accounted for the decreasing of the crystallinity of PEO-LiX. We reviewed these results and have investigated the degradation processes of PEO using Tb³⁺ fluorescence probes. We have also studied on the effects of irradiation of polymers such as poly(acrylic acid) (PAA), poly(methacrylic acid) (PMA) and PEO using Tb⁺³ fluorescence probe. Various monomers containing SO₃H and COOH have been grafted on poly(ethylene oxide) using irradiation technique. The structures and ionic conductivities of Li and Na salts of irradiated products were investigated in detail.     

Influence of electron beam irradiation on the impact properties of polystyrene/EPDM rubber blends

The influence of electron beam (EB) irradiation on the impact properties of compatibilized polystyrene/ethylene-propylene-diene-monomer (PS/EPDM) blends was studied. The change in impact value upon irradiation proved to be strongly dependent on the type of compatibilizer used. Using a polystyrene/polybutadiene (SB) diblock copolymer as a compatibilizer, a twofold increase in Izod value could be achieved upon irradiation. Irradiation of a blend using a polystyrene/ethylene-propylene (SEP) copolymer as a compatibilizer resulted in a decrease in impact strength. These observations can be related to a radiation induced increase in interfacial adhesion in case of the SB copolymer, which does not occur for the SEP copolymer. Due to the abundance of double bonds in the SB copolymer, this copolymer reacts very fast upon irradiation and may co-crosslink with, or graft onto the EPDM phase. For the SEP copolymer crosslinking occurs only at much higher doses and is (partly) overruled by chain scission and consequently the adhesion between matrix and dispersed phase will hardly change. This view is supported by analytical methods as FT-IR and NMR as well as from T_g measurements.     

Structural and physico-chemical studies on modification of polypropylene and its polyphenolic antioxidant by electron beam irradiation

As polypropylene (PP) is widely used in medical and pharmaceutical fields, the effect of sterilization on both the polymer and its additives must be taken into account. In this study, PP and its antioxidants Irganox 1010 and 1076 were electron beam irradiated in order to evaluate by Fourier transform infrared spectroscopy, differential scanning calorimetry and size exclusion chromatography, their structural and physico-chemical modifications. A good correlation between those analytical techniques has indicated the formation of oxidation products, chain scissions as well as crosslinking. The effect of the absorbed dose is underlined.     

Effect of electron beam irradiation on physico-chemical properties of pullulan

Many widely used polymers undergo main chain scission or crosslinking when exposed to radiation. Effects of electron beam irradiation at different doses up to 500?kGy on the biodegradable pullulan polymer films have been investigated by ultraviolet?Cvisible (UV?CVIS), Fourier transform infrared spectroscopy (FTIR), scanning electron microscopy (SEM), and thermogravimetric analysis (TGA) techniques. UV?CVisible study shows increase of optical absorbance with increase of doses, attributing to the formation some groups or radicals. FTIR and TGA results reveal the processes of both crosslinking and degradation of polymer taking place depending upon the dose of e-beam radiation. The surface morphology of the film is found to be altered by the e-beam radiation as indicated by SEM micrographs.     

Oxidation of gaseous styrene by electron beam irradiation

In this research, the absorbed dose, background gases, relative humidity, and initial concentrations were selected as control factors to discover decomposition characteristics of styrene using electron beam irradiation. It was confirmed that a considerable amount of styrene was removed by primary electrons as well as radicals and ions, which were produced after the electron beam irradiation. Moreover, the removal efficiencies of styrene were observed to rise when the initial concentration was lower, moisture content was higher, and the absorbed dose increased. For instance, 50 ppmv styrene showed extremely high removal efficiency (over 98%) at a condition of 2.5 kGy. A small amount of styrene oxide, benzaldehyde, aerosol, CO, and CO₂ were produced as by-products after EB irradiation.     

Changes of biodiesel composition after electron beam irradiation

Journal of Radioanalytical and Nuclear Chemistry - The study of the influence of external factors on FAME is increasingly being taken up with research topics. Under natural conditions, they are...     

Cyclization and crosslinking of polybutadiene in solution by electron beam irradiation

Effects of electron beam irradiation on liquid polybutadiene in n-hexane solution were studied at ?10°C. With irradiation, crosslinking of the polymer and loss of double bond by cyclization took place at the same time. These reactions were retarded by the addition of DPPH or triethylamine which indicated that both radical and cationic mechanisms contributed to this system.     

Degradation of prednisone in aqueous solutions by electron beam irradiation

A novel degradation study of prednisone (PRE) in aqueous systems (10 mg L^?1) was performed under electron beam irradiation (EBI) in various conditions. The data demonstrate that the highest degradation caused by EBI was obtained with the oxidation of hydroxyl radicals. The proper amount of hydrogen peroxide could increase the PRE total carbon content removal rate. Nine degradation products of PRE in aqueous solution were preliminarily analyzed using ultra-high performance liquid chromatography in combination with mass spectrometry. Furthermore, the chemical analysis and possible degradation pathway were proposed with the assistance of theoretical calculation results by density functional theory.     

Crosslinking of recycled polyethylene by gamma and electron beam irradiation

Recycling of polymeric materials is usually accompanied by degradation and deleterious properties. Irradiation crosslinking of recycling low density polyethylene by electron beam and gamma rays could be the solution to improve their properties. This paper presents a comparison on the effects of gamma and electron irradiation on virgin and recycled polyethylene. Their mechanical, thermal and chemical properties were analyzed. VPE samples shown higher crosslinking percentages than RPE samples in all range of doses studied, unirradiated RPE samples had higher values on their tensile properties than VPE. Percentage crystallinity was similar in all range of doses studied.     

Modification of fluoropolymers by means of electron beam irradiation

High molecular weight polytetrafluoroethylene (PTFE) is transformed to free-flowing micropowder by treatment with electron beams. In case of irradiation in presence of air carboxylic acid fluoride groups are incorporated which rapidly hydrolyze to carboxylic groups in the surface-near regions due to atmospheric humidity. These polar groups reduce the hydrophobic and oleophobic properties so much that homogeneous compounding with other materials becomes possible. In addition to PTFE, copolymers of tetrafluoroethylene with hexafluoropropylene (FEP) and perfluoropropylvinylether (PFA) were modified. In case of identical irradiation conditions, the concentration of carboxylic groups is much higher in FEP and PFA than in PTFE, which is due to the lower crystallinity of the copolymers.

Electron beam irradiation of PTFE was performed in vacuum at elevated temperature above the melting point. The changes in the chemical structure were studied. The concentration of CF₃ branches was found to be much higher as compared to room temperature irradiation.

In a practical test PTFE micropowders functionalized by electron irradiation were compounded with epoxy resins, with polyoximethylene and with polyamides. Such compounds are characterized by very good frictional and wearing behaviour in dry-running tests.     

Biodegradability enhancement of textile wastewater by electron beam irradiation

Textile wastewater generally contains various pollutants, which can cause problems during biological treatment. Electron beam radiation technology was applied to enhance the biodegradability of textile wastewater for an activated sludge process. The biodegradability (BOD₅/COD) increased at a 1.0 kGy dose. The biorefractory organic compounds were converted into more easily biodegradable compounds such as organic acids having lower molecular weights. In spite of the short hydraulic retention time (HRT) of the activated sludge process, not only high organic removal efficiencies, but also high microbial activities were achieved. In conclusion, textile wastewater was effectively treated by the combined process of electron beam radiation and an activated sludge process.     

Effects of electron beam irradiation on microbial contamination and quality of Shengmai Yin

Journal of Radioanalytical and Nuclear Chemistry - In this study, Shengmai Yin (SMY) was irradiated at doses of 2, 3, 5, and 7 kGy of electron-beam, to investigate the effects of electron...     

Control factors and by-products during decomposition of butane in electron beam irradiation

This research was conducted to determine the removal characteristics of butane, using an electron beam. Influential factors, such as an initial concentration, background gases (nitrogen, air, and helium), and absorbed doses (kGy) were investigated. The decomposition efficiencies of background gases showed that oxidation caused by radicals formed from gases, such as N₂ and O₂, had a greater influence on results than oxidation from primary electrons for butane removal. Removal efficiencies were 40% at 2.5 kGy and 66% at 10 kGy, when the initial concentration of butane was 60 ppmC. When the initial concentration was lower, the energy efficiency of butane removal by electron beam was higher. By-products, including CO₂, CO, acetaldehyde, and acetone, formed after electron beam irradiation. Concentrations of CO₂ and CO tended to increase when absorbed doses increased as butane was decomposed by the electron beam through an advanced oxidation.     

Immobilization of a hyperbranched polyester via grafting-to and electron beam irradiation

Stable thin films of an aromatic-aliphatic hyperbranched polyester with hydroxyl groups were fabricated on silicon substrates using electron beam irradiation and a grafting-to approach. We present a detailed study on the influence of the dose, dose rate, and temperature on the film properties and degradation behavior of the polyester immobilized by electron beam irradiation. A patterned polyester film was prepared on the substrate using a masking technique. In the second part of this work, we report on a method for the strong binding of the hyperbranched polyester onto the surface of an "activated" silicon substrate without using any coupling agent. The results are compared with the grafting-to of the hydroxyl-terminated polyester using thin PGMA anchoring layers ( Reichelt et al. Macromol. Symp. 2007, 254, 240- 247 ). The optimal conditions and mechanism of the anchoring procedures were investigated. The surface and film properties of all immobilized polymer films were characterized by atomic force microscopy (AFM), X-ray photoelectron spectroscopy (XPS), electrokinetic measurements, contact-angle measurements by drop-shape analysis, spectroscopic and imaging ellipsometry, and infrared spectroscopy. It is shown that all immobilization methods can be optimized in such a way that the polymer surface properties remain unchanged compared to those of nongrafted polyesters.