Copolyesters of glycols and bisphenols: Concurrent reactions of a new preparative process

A mechanism for the preparation of copolyesters from a preformed polyester, diacid, and bisphenol diacetate in the melt phase is described. Utilizing copoly(ethylene:4,4′-isopropylidenediphenylene 50:50 2-methylisophthalate) as a model system, the reaction is shown to proceed through simultaneous cleavage of the preformed polyester by diacid, polymerization by condensation of carboxyl and bisphenol acetate groups, and equilibration through polyester cleavage by carboxyl polymer ends. In this model system, the rates of cleavage and polymerization are competitive, which results in a random sequence distribution early in the reaction.     

ABA triblock copolyesters composed of poly(l-lactide) A hard blocks: A comparative study of amorphous and crystalline aliphatic polyesters as B soft blocks

In this article, two series of ABA triblock copolyesters composed of poly(l-lactide) A hard blocks and odd-odd aliphatic polyesters as B soft midblock were prepared and compared by various techniques. The results showed that the block structures could be formed without any detectable transesterification, and the composition and molecular weight of the triblock copolyesters could be well controlled by adjusting the feeding ratio of l-lactide monomer to the polyester macroinitiator. It was found that the thermal properties, crystal structure, and spherulitic morphology of the triblock copolyesters depended on the composition and block length. The impact of amorphous and crystalline midblocks on the mechanical properties was compared and discussed. The triblock copolyesters composed of crystalline midblock showed similar ultimate stress and elongation, but higher tensile modulus and yield stress, in comparison with analogous containing amorphous midblock. The triblock copolyester composed of short PLLA hard block and amorphous aliphatic polyester soft midblock displayed typical elastomeric behavior without yield, which is a promising aliphatic polyester thermoplastic elastomer.     

Synthesis of Aromatic Polyesters Bearing Pendant Carboxyl Groups by Phase Transfer Catalysis

Aromatic polyester (PEA) and copolyesters having pendant carboxyl groups aredirectly synthesized from isophthaloyl chloride, diphenolic acid and diols byaqueous/organic two-phase interfacial polycondensation, using phase transfercatalysts. The yield and molecular weight of the polyester were remarkablyaffected by the structure of quaternary ammonium salts and crown ether catalysts.The phase transfer reaction steps are suggested to explain this phenomena. Theproperties of copolyesters were dependent on the original structure of diols.     

New polymer synthesis. LXXXIII. Synthesis of chiral and cholesteric polyesters from silylated “sugar diols”

A series of polycondensation was conducted with the purpose to optimize the reaction conditions for the polycondensation of silylated 2,3-isopropylidene D -threitol with a dicarboxylic acid dichloride. Polycondensation in o-dichlorobenzene or 1-chloronaphthalene at 180–230°C were found to be most satisfactory. Trifluoroacetic acid/H₂O allow an easy cleavage of the isopropylidene group without hydrolysis of the polyester. Ten cholesteric copolyesters were prepared by polycondensation of mixtures of silylated methylhydroquinone and isosorbide, isomannide, or 2,3-isopropylidene threitol with the dichloride of 1,10-bis(4′-carboxyphenoxy)decane. All these copolyesters form a broad cholesteric phase above 200°C. The copolyesters containing 5 or 10 mol % of a sugar diol display a blue Grandjean texture. © 1996 John Wiley & Sons, Inc.     

Melt transesterification and characterization of segmented block copolyesters containing 2,2,4,4‐tetramethyl‐1,3‐cyclobutanediol

Conventional melt transesterification successfully produced high‐molecular‐weight segmented copolyesters. A rigid, high‐T_g polyester precursor containing the cycloaliphatic monomers, 2,2,4,4‐tetramethyl‐1,3‐cyclobutanediol, and dimethyl‐1,4‐cyclohexane dicarboxylate allowed molecular weight control and hydroxyl difunctionality through monomer stoichiometric imbalance in the presence of a tin catalyst. Subsequent polymerization of a 4000 g/mol polyol with monomers comprising the low‐T_g block yielded high‐molecular‐weight polymers that exhibited enhanced mechanical properties compared to a nonsegmented copolyester controls and soft segment homopolymers. Reaction between the polyester polyol precursor and a primary or secondary alcohol at melt polymerization temperatures revealed reduced transesterification of the polyester hard segment because of enhanced steric hindrance adjacent to the ester linkages. Differential scanning calorimetry, dynamic mechanical analysis, and tensile testing of the copolyesters supported the formation of a segmented multiblock architecture. Further investigations with atomic force microscopy uncovered unique needle‐like, interconnected, microphase separated surface morphologies. Small‐angle X‐ray scattering confirmed the presence of microphase separation in the segmented copolyesters bulk morphology. © 2012 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2012     

聚对苯二甲酸二甲酯/聚2,5-呋喃二甲酸二甲酯嵌段聚酯的合成与表征

以生物基单体2,5-呋喃二甲酸、乙二醇为原料合成聚2,5-呋喃二甲酸乙二醇酯(PEF)。采用熔融酯交换法以PEF聚酯部分取代聚对苯二甲酸乙二醇酯(PET),制备了系列PET-b-PEF嵌段共聚酯。通过核磁共振仪(NMR)、差示扫描量热仪(DSC)、热失重仪(TGA)、X射线衍射仪(XRD)等技术手段表征了共聚酯的结构和性能。结果表明,该系列共聚酯的玻璃化转变温度(Tg)在75.8~80.3℃之间,且随着PEF链段质量分数的增加,PET-b-PEF嵌段共聚酯的Tg先降低后升高,结晶度和熔融温度逐渐降低。当PEF链段含量高于15%时,共聚酯没有结晶峰。该系列共聚酯具有良好的热稳定性,起始分解温度在392.2~407.9℃之间,与所制备的PET起始分解温度403.3℃接近。且当共聚酯中PEF链段含量低于15%时,起始分解温度均在407℃左右,优于PET的热稳定性。     

Synthesis and characterization of fully biobased poly(propylene succinate‐ran‐propylene adipate). Analysis of the architecture‐dependent physicochemical behavior

Fully biobased aliphatic random poly(1,3‐propylene succinate‐ran‐1,3‐propylene adipate) (PPSA) copolyesters with high molar mass were synthesized with different macromolecular architectures based on various succinic acid/adipic acid (SA/AA) molar ratio, by transesterification in melt. Titanium (IV) isopropoxide was used as an effective catalyst. All synthesized copolyesters were fully characterized by different chemical and physicochemical techniques including NMR, size exclusion chromatography, FTIR, wide angle X‐ray scattering, differential scanning calorimetry, and thermogravimetric analysis. The final copolyesters molar compositions were identical to the feed ones. The different sequences based on succinate and adipate segments were randomly distributed along the chains. All the corresponding copolyesters showed an excellent thermal stability with a degradation onset temperature higher than 290 °C, which increased with the adipate content. According to their compositions and architectures, PPSA copolyesters can exhibit or not a crystalline phase, at room temperature. T_g of copolyesters decreased with the adipate content due to the decrease in the chains mobility, following the Gordon–Taylor relation. PPSA showed a pseudo eutectic melting behavior characteristic of an isodimorphic character. Finally, PPSA copolyesters were not able to crystallize during the cooling or the second heating run, due to the 1,3‐propanediol chemical structure, which led to amorphous materials with the exception of the polyester based solely on AA. © 2017 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2017 , 55, 2738–2748     

Synthesis, characterization and properties of high molecular weight poly(butylenes succinate) reinforced by mesogenic units

To increase the molecular weights of the synthesized liquid crystalline aromatic/aliphatic copolyesters and to avoid crosslinking, a solution polymerization of the prepolymer and chain extender hexamethylene diisocyanate was adopted. The effects of chain extension on polyester molecular weights, thermal and mechanical properties, and biodegradable behaviors were investigated respectively. The catalysis mechanism and the copolyesters morphological textures were also investigated. The synthesized copolyesters were characterized by means of Fourier transform infrared spectra (FTIR), gel permeation chromatography (GPC), viscosity measurements, differential scanning calorimetry (DSC), X-ray diffraction (XRD), polarizing light microscopy (PLM), scanning electron microscopy (SEM) and mechanical property measurements. It was found that inherent viscosities and the molecular weights of the copolyesters were remarkably increased under the action of catalyst, leading to a increase in the tensile strength. The degree of relative crystallinity, the melting temperature, and the rate of degradation decreased after chain extension.     

含X-型二维液晶基元和顺式-4,4′-双(4-羟基苯基偶氮)二苯并-18-冠-6冠醚环液晶共聚酯的合成与表征

以4,4-′(α,ω-辛二酰氧)二苯甲酰氯(M1)、2,5-双[4-′(对癸氧基苯基)苯甲酰氧基]对苯二酚(M2)和顺式-4,4′-双(4-羟基苯基偶氮)二苯并-18-冠-6(M3)为单体,通过溶液共缩聚反应,合成了一系列新的含X-型二维液晶基元和顺式-4,4′-双(4-羟基苯基偶氮)二苯并-18-冠-6冠醚环的主链型液晶共聚酯.单体1(M1)由对羟基苯甲酸和辛二酰氯,通过酯化和取代反应制备,单体2(M2)由2,5-二羟基苯醌和对癸氧基苯基苯甲酰氯通过酯化和还原反应制备,单体3(M3)由顺式-二氨基二苯并-18-冠-6和苯酚通过重氮化和偶联反应制备.共聚酯的分子量不高,[η]在0.30~0.39之间.单体的化学结构通过IR、UV1、H-NMR、MS和元素分析等方法确证.共聚酯的外观为黄色粉状固体,除共聚酯CP9外,室温下不溶于CHCl3和THF溶剂.共聚酯的性质采用GPC、[η]、DSC、TG、WAXD和POM等方法进行了研究,发现所有的共聚酯加热到各自的熔融温度以上都能形成液晶态,在液晶态可以观察到近晶相和向列相的典型织构.共聚酯的熔融温度(Tm)和各向同性温度(Ti)随共聚酯分子中顺式-4,4′-双(4-羟基苯基偶氮)二苯并-18-冠-6用量的改变呈规律性变化.WAXD研究进一步证实了共聚酯的液晶性.     

Copolyesters of hydroxyphenylalkanoic acids: Synthesis,properties, and in vitro degradation of poly(4‐oxybenzoate‐co‐4‐oxyphenylacetate)

Hydrolytically degradable copolyesters of the naturally occurring monomer 4‐hydroxyphenylacetic acid (HPAA) with 4‐hydroxybenzoic acid (HBA) were synthesized for the first time by the acidolysis melt polymerization of their acetoxy derivatives. The HPAA/HBA copolyesters prepared by acidolysis melt polycondensation had higher yields and molecular weights than those obtained by a one‐pot method. The high‐temperature solvent Dowtherm® improved the color of the polyester. Although catalysts did not affect the inherent viscosity and yield of the polymer, they did reduce the polymerization time. A higher degree of polymerization was achieved with postpolymerization and annealing techniques. Copolyesters prepared in different molar ratios were analyzed by elemental analysis, IR, NMR, and inherent viscosity and were further characterized for their thermal and phase properties by thermogravimetric analysis, differential scanning calorimetry, wide‐angle X‐ray diffraction, and polarized light microscopy. The composition of the copolyesters affected the yield, solubility, and inherent viscosity. The NMR data indicated comparatively high randomization for the copolyester obtained by acidolysis melt polymerization. The 60/40 HPAA/HBA copolyester formed a birefringent melt with a grainy texture above 175 °C with isotropization at 297 °C and thermal stability above 350 °C. The occurrence of birefringence with a grainy texture in the melt indicates a layered smectic phase; this was supported by wide‐angle X‐ray diffraction powder patterns. The in vitro hydrolytic degradability of the copolyester was studied by the measurement of the water absorption of the film samples in buffer solutions of pH 7 and 10 at 30 and 60 °C. The copolyester showed considerable hydrolytic degradation, enough to be called biodegradable, compared with the commercial polyester Vectra®, thereby demonstrating prospects for syntheses of copolyesters with tailor‐made degradability. The degradation of the copolyester was identified by Fourier transform infrared, differential scanning calorimetry, thermogravimetric analysis, and scanning electron microscopy. These polyesters with controlled crystallinity and degradability should be considered for possible applications in biomedical areas (e.g., bone fixation devices in fracture treatment) in which high strength with biodegradability is an essential requirement. © 2001 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 39: 693–705, 2001     

Synthesis of reactive copolyesters derived from isophthaloyl chloride,bisphenol a,and aliphatic diols with additional reactive groups

Copolycondensation of isophthaloyl chloride, bisphenol A, and aliphatic diols with additional reactive groups were performed in the presence of triethylamine by a trimethyl phosphate/cyclohexane organic/organic interfacial method. The composition of idol and bisphenol A residues in the resulting copolyesters is very close to that in the feed from the initial stage of reaction. The resulting copolyesters with reactive groups can be used for the preparation of various functional polymers. The mechanism of an organic/organic interfacial polycondensation was also discussed. © 1995 John Wiley & Sons, Inc.     

Synthesis of polyesters having quaternary ammonium groups in the side chains and preparation of their blends with poly(vinyl alcohol)

Triethyl-2,3-propanediolammonium chloride (TPC) was prepared and used for the preparation of polyester and copolyesters having quaternary ammonium groups in the side chains. The polycondensation of isophthaloyl dichloride with TPC and other dihydroxy compounds was performed by the organic phase/organic phase interfacial polycondensation method using N,N-dimethylacetamide/n-heptane or trimethyl phosphate/n-heptane as reaction media in the presence of tetramethyl ethylenediamine. Blend films were prepared from these polyesters and poly(vinyl alcohol) by casting from aqueous or aqueous NaOH solution. The electrical conductivity of the blend films is remarkably affected by the moisture content and in the order of 10^?5 ～ 10^?8 S/cm in the presence of moisture. © 1994 John Wiley & Sons, Inc.     

三组分共聚酯数均聚合度和数均分子量的计算方程

为便于生产控制以制得预定分子量的产物，根据直接酯化法合成聚对苯二甲酯乙二酯（ＰＥＴ）共聚酯的特点，综合考虑各种主、副反应，从统计观点出发，对三组分ＰＥＴ共聚酯体系的齐聚物和缩聚物，分别建立了其数均聚合度Ｘｎ和数均分子量Ｍｎ的简化和非简化计算方程．将简化Ｘｎ方程与Ｃａｒｏｔｈｅｒｓ方程进行计算比较，其结果完全相同；将简化Ｘｎ方程应用于二组分聚酯体系，其形式与传统的二组分线型缩聚物Ｘｎ方程形式相同，各Ｘｎ和Ｍｎ方程可推广应用于二组分聚酯体系和三组分以上的多组分共聚酯体系．     

Biodegradable aliphatic/aromatic copolyesters based on terephthalic acid and poly(L-lactic acid): Synthesis, characterization and hydrolytic degradation

<正>Biodegradable aliphatic/aromatic copolyesters,poly(butylene terephthalate-co-lactate)(PBTL) were prepared via direct melt polycondensation of terephthalic acid(TPA),1,4-butanediol(BDO) and poly(L-lactic acid) oligomer(OLLA). The effects of polymerization time and temperature,as well as aliphatic/aromatic moiety ratio on the physical and thermal properties were investigated.The largest molecular weight of the copolyesters was up to 64100 with molecular weight distribution index of 2.09 when the polycondensation was carried out at 230℃for 6 h.DSC,XRD,DMA and TGA analysis clearly indicated that the degree of crystallinity,glass-transition temperature,melting point,decomposition temperature, tensile strength,elongation and Young's modulus were influenced by the ratio between TPA and OLLA in the final copolyesters.Hydrolytic degradation results demonstrated that the incorporation of biodegradable lactate moieties into the aromatic polyester could efficiently improve hydrolytic degradability of the copolymer even though it still had many aromatic units in the main chains.     

SYNTHESIS AND AVERAGE SEQUENCE LENGTH DETERMINATION OF AROMATIC-ALIPHATIC COPOLYESTERS CONTAINING POLY(ALKYLENE OXALATE) UNITS

Two series of aromatic-aliphatic random copolyesters(PEBTOXS)with diverse diol ratios have been synthesized by direct melting polycondensation.Two kinds of diols(glycol(EG)and 1,4-butanediol(BD))are used in combination in order to adjust crystallization and tensile properties,and three kinds of diacids(dimethyl terephthalate(DMT),diethyl oxalate(DEOX),and sebacic acid(SA))are involved.~1H-NMR spectra quantify both composition and structure,and show that the final contents in copolyesters appropriate to t...     

Hydrodispersible copolyesters: Relationship between chemical structure and physico-chemical properties

Anionic copolyesters with sodium sulfonate functions and short polyethylene oxyde blocks are used for polyester filament sizing. These polymers were prepared using a three stages melting process at high temperature combining ester interchange, direct esterification, polycondensation and etherification reactions. A study on the relationship between chemical structure and physico-chemical properties (glass transition temperature, solubility behaviour, hydrolytical and thermal stability) shows that the control of the ether bridges content is important.     

Novel copolyesters based on poly(alkylene dicarboxylate)s: 2. Thermal behavior and biodegradation of fully aliphatic random copolymers containing 1,4-cyclohexylene rings

Aliphatic poly(butylene 1,12-dodecanedioate) is an interesting biodegradable polyester characterized by high thermal stability and high crystallinity, but low melting temperature. In order to improve the performances of this polymer some novel fully aliphatic random copolyesters have been prepared starting from 1,4-butanediol and different molar ratio of 1,12-dodecanedioc acid and 1,4-cyclohexanedicarboxylic acid. The copolymers have a notable resistance to thermal degradation, thermal properties which vary as a function of the composition, and maintain the mechanical characteristics of the poly(alkylene dicarboxylate). In particular, the copolymer containing the 70 mol% of 1,4-cyclohexanedicarboxylate units improves the thermal properties of the poly(butylene 1,12-dodecanedioate) and presents a very high biodegradation rate, higher than those of the two parent homopolymers. This behavior has been correlated to the low level of crystallinity of the sample and to the composition of the amorphous phase. Therefore, these novel fully aliphatic copolymers represent an interesting new class of copolyesters which can balance good physical properties and high biodegradability.     

Structural effects on biodegradation of aliphatic polyesters

Various types of aliphatic polyesters were prepared by both biosynthetic and chemosynthetic methods, and their biodegradation tests were carried out under aerobic conditions in the river water. Biodegradabilities of polyester films were evaluated by monitoring the time-dependent changes in the biochemical oxygen demand (BOD), weight loss (erosion) of polyester film, and dissolved organic carbon concentration (DOC) of test solution. The microbial copolyesters were degraded in the river water at a rapid rate, and the weight-loss- and BOD-biodegradabilities of the majority of biosynthetic polyesters were 100 % and 80±5 % for 28 days, respectively. In contrast, the biodegradabilities of chemosynthetic polyesters were strongly dependent of the chemical structure of monomeric units.     

Novel biodegradable copolyesters containing blocks of poly(3-hydroxyoctanoate) and poly(epsilon-caprolactone): synthesis and characterization

Novel biodegradable polyester block copolymers have been synthesized by using well-defined poly(3-hydroxyoctanoate) (PHO) oligomers having a hydroxyl end group and an ester end group with M(n) values of 800, 2,500, 5,300, 8,000, or 20,000 as an elastomeric soft segment and poly(epsilon-caprolactone) as a more crystalline segment. These PHO oligomers prepared by methanolysis were subjected to block copolymerization with epsilon-caprolactone. The chemical structure of the copolymers was confirmed by (1)H NMR and (13)C NMR spectroscopy. All the copolyesters are semi-crystalline and two T(g) were observed by differential scanning calorimetry when the molecular weight of the PHO block is about 20,000.     

Synthesis, characterization and biodegradable studies of 1,3-propanediol based polyesters

A series of biodegradable polyesters were synthesized from dicarboxylic acids and 1,3-propanediol catalyzed by transestrification polycondensation reaction in the bulk. The structure, average molecular weights and physical properties of the resulting aliphatic polyesters were characterized by ¹H NMR, FT-IR, solution viscosity, GPC, DSC and TGA. Homopolyesters show higher degree of crystallinity, melting and thermal stability in comparison to copolyesters. The biodegradability of the polyesters was determined by monitoring the normalized weight loss of polyester films with time in phosphate buffer (pH 7.2) without and with Rhizopus delemar lipase at 37 °C. The rate of enzymatic degradation of homopolyesters follows the path PPSu > PPAd > PPSe. PPSe did not show significant weight loss in presence of enzyme which may be due to its highest degree of crystallinity and melting point compared to the PPSu, PPAd and copolyesters. In the soil burial degradation polyester sample showed severe surface degradation by the attack of microorganism.