静态水热晶化法高效合成MCM-22分子筛

 采用静态水热晶化法，在Na2O－Al2O3－SiO2－HMI－H2O（HMI：六亚甲基亚胺）体系中，在HMI／SiO2摩尔比为0．09，H2O／SiO2摩尔比为12，晶化时间为60～80h的条件下，合成了MCM－22分子筛．利用固体硅胶表面的吸附性能提高模板剂的局部浓度，从而实现了分子筛的高效合成．对合成条件的研究结果表明，以比表面积（486m2／g）大、反应性能好的硅胶为硅源是静态水热晶化法高效合成MCM－22分子筛的关键，而成胶老化方式对MCM－22分子筛的晶化影响不大．产物的晶相和转晶的类型取决于合成凝胶的初始硅铝比．当SiO2／Al2O3摩尔比＝18～80时可以合成出MCM－22，当SiO2／Al2O3＝13～17时可以合成出MCM－49．硅铝比较低（如SiO2／Al2O3＝20）时，MCM－22分子筛易转晶为MOR分子筛，而在硅铝比较高（如SiO2／Al2O3＝50）时，可转晶为ZSM－5分子筛．     

HZSM-5型分子筛硅铝比对一步法合成二甲醚的影响

以Cu/Zn/Al(摩尔比为6∶3∶1)甲醇合成催化剂与HZSM-5型分子筛混合,制备了一步法二甲醚合成催化剂。通过改用三种不同Si/Al摩尔比（摩尔比为25、38和50）的HZSM-5型分子筛,考察了催化剂中脱水组分（HZSM-5分子筛）的酸性对二甲醚合成的影响。结果表明,随着催化剂Si/Al摩尔比的降低,分子筛的酸性增强,使得CO单程转化率提高。当催化剂Si/Al＝38时,CO对二甲醚的选择性最高,可达到68.13％,其次是催化剂Si/Al＝50,选择性最差的是Si/Al＝25的催化剂。在553 K、 3 MPa和4 000 h－1的条件下,Si/Al＝25和Si/Al＝38的催化剂CO单程转化率和DME的选择性接近一致。在此条件下,两者的时空产率达到试验的最大值,分别为0.38 gDME/(gcat·h)和0.36 gDME/(gcat·h),在试验范围内,一步法合成二甲醚催化剂最佳的Si/Al摩尔比为25。     

中孔分子筛HMS负载钴催化剂在费-托合成中的应用:载体HMS的孔径对钴基催化剂性能的影响

 用不同链长度的十二胺，十四胺，十六胺和十八胺等伯胺为模板\r\n剂合成了具有不同孔径大小的HMS中孔分子筛．XRD和低温氮吸附测定表\r\n明，HMS具有典型的中孔分子筛特征，且其孔径大小随HMS合成中所用模\r\n板剂链长度的增加而增加．以HMS为载体，采用孔体积浸渍法制备了负\r\n载量为7．5％的钴催化剂，在接近工业试验条件下（n（H2）／n（CO）\r\n＝2．1，GHSV＝500h－1，p＝2．0MPa，θ＝227℃）考察了载体孔径大\r\n小对费－托合成反应性能的影响．结果表明，与常规的SiO2载体相比，\r\nHMS负载钴催化剂具有更高的催化活性和C5＋选择性；而且，CO转化率\r\n，C5＋选择性及产物中的蜡油比均随着HMS载体孔径的增大而升高．以\r\n7．5％Co／HMS－18为催化剂，CO转化率为78．0％，C5＋选择性为80．\r\n8％，蜡油比为11．1．     

含铜三元类水滑石化合物的合成及其性质

 以Cu（NO3）2，Zn（NO3）2和Al（NO3）3为原料，以NaOH为沉淀剂，利用共沉淀法合成了含铜三元类水滑石化合物CuZnAl－HTLcs．从不同Cu／Zn／Al比的混合原料溶液的滴定曲线入手，详细探讨了溶液pH值、原料加入方式、组分配比及水热处理条件对类水滑石合成的影响，利用XRD，ICP及比表面积测定对合成物进行了表征，并以苯酚羟基化为探针反应评价了催化剂的催化性能．结果表明，在体系pH＝5．0～6．2，（Cu＋Zn）／Al摩尔比＝2．0，Cu／Zn摩尔比≤1．0及室温条件下共沉淀后，于100℃水热处理3h，即可得到晶相单一和结晶度高的CuZnAl－HTLcs．变化pH法合成的样品的相对结晶度为100％，低过饱和法为76．5％，高过饱和法为75．9％．合成的CuZnAl－HTLcs中Cu2＋的含量均比原料液中Cu2＋的含量有所增加，这可能是由于在pH＝5．8时Cu2＋对Al（OH）3的同晶取代能力比Zn2＋强．随着CuZnAl－HTLcs中Cu含量的增加，催化剂对苯酚羟化反应的催化活性逐渐增大．     

高硅ZSM-5分子筛和二次合成Ti-ZSM-5分子筛的结构

运用度角旋转（MAS）和交叉极化（CP）等核磁共振波谱和红外光谱技术，分别对采用不同模板剂制备的高硅ZSM－5分子筛和以此为母体，经气固同晶取代法得到Ti－ZSM－5分子筛的结构特性进行了研究．结果表明：在水热法合成高硅ZSM-5分子筛过程中，模板剂明显制约着所制得的分子筛的结构特性．通过选用合适的模板剂，可直接获得具有正交晶系结构的高硅ZSM－5分子筛．在随后的气固相同晶取代过程中，钛原子通过占据分子筛骨架中的缺陷位进入骨架，形成具有一定Ti／Si比例的钛硅分子筛（Ti－ZSM－5）。骨架结构中缺陷位的含量直接影响分子筛的载钛量。     

全硅MEL纳米分子筛的合成及物化性质I.全硅MEL纳米分子筛的合成

在TEOS-TBAOH-H_2O反应物体系中，水热条件下制备了全硅MEL （Silicalite- 2）沸石纳米晶。详细讨论反应物中TBAOH/TEOS摩尔比、H_2O/TEOS摩乐比、反应温 度等对沸石粒径的影响。结果表明，反应物中较高的碱度和TEOS（硅源）浓度，及 较低的晶化温度有利于MEL纳米分子筛的合成。     

新型钴基介孔分子筛催化剂F-T合成性能和烃分布研究

采用介孔分子筛MSU－1，SBA－12和HMS为载体，制得含钴质量分数为15％的催化剂。在原料气V（H2）／V（CO）＝2．0，T＝473－513K,p=2.0MPa,GHSV=500H^-1的F－T合成条件下，反应活性依Co/HMS,Co/SBA-12,Co/MSU-1顺序降低，高碳烃（C19^ )选择性以Co/HMS最低；Co/MSU-1和Co／SBA-12催化剂介孔结构在反应中相对稳定，Co/HMS介孔结构在反应后完全塌陷。     

以四丙基溴化铵为模板剂合成TS-1分子筛的研究

运用1H→13CCP／MASNMR、29SiMASNMR、IR、XRD和元素分析等表征方法，研究了以四丙基溴化铵（TPABr）为模板剂的合成体系中，Ti酯和模板剂用量以及不同碱源对TS-1分子筛的影响，考察了不同Ti含量固体样品催化丙烯环氧化反应．实验结果表明：随着凝胶中Ti酯用量的增加，制得的分子筛结构对称性由单斜晶系逐渐向正交晶系转变，其丙烯环氧化活性也相应增加．尽管凝胶中所加减源只调变凝胶碱度而不起模板剂作用，然而凝胶的强碱环境对骨架钛原子引入有利．当凝胶中TPABr／SiO2摩尔比值在0．05－0.25之间时，TPABr加入量的变化不影响TS－1分子筛中骨架钛含量．     

全硅MEL纳米分子筛的合成及物化性质I．全硅MEL纳米分子筛的合成

在TEOS-TBAOH-H_2O反应物体系中,水热条件下制备了全硅MEL （Silicalite- 2）沸石纳米晶。详细讨论反应物中TBAOH/TEOS摩尔比、H_2O/TEOS摩乐比、反应温 度等对沸石粒径的影响。结果表明,反应物中较高的碱度和TEOS（硅源）浓度,及 较低的晶化温度有利于MEL纳米分子筛的合成。     

高硅分子筛ZSM-22的动态合成及表征

 以1，6－己二胺（DAH）为模板剂，采用水热条件下的动态合成方法，合成出结晶度良好的ZSM－22晶体．研究表明，合成的关键是避免ZSM－5分子筛的生长，当n（Si）／n（Al）＝25～65，n（H2O）／n（SiO2）＝16．3～40．3，n（DAH）／n（Si）＝0．1～0．6和T＝428～448K时，都能稳定合成出ZSM－22分子筛．采用TEM，XRD，TG－DTA和NH3－TPD等方法，对ZSM－22晶体的形貌，生长动力学，模板剂的作用以及硅铝比对分子筛酸性的影响等进行了较详细的研究．实验结果和理论计算证实，1，6－己二胺分子以首尾相连的方式，线性排列并完全充满ZSM－22的十元环孔道，同时起到结构导向和骨架电荷平衡的作用．     

二氧化碳和丙烯直接合成甲基丙烯酸的NiPMo/TiO2催化剂的研究

用溶胶-凝胶法以磷钼酸(MPA)的镍盐溶液水解钛酸四丁酯制备了NiPMo/TiO2催化剂.使用ICP、 XRD、 TG-DTA、 IR、 TPD-MS和微反应技术研究了催化剂的化学组成、热稳定性、化学吸附性质和催化反应性能.杂多钼酸盐与TiO2通过O2-在TiO2表面发生了键合.在623 K下,杂多阴离子仍保持原有的Keggin结构.CO2在Lewis酸位Ni(Ⅱ)和Lewis碱位Ni-O-Mo的桥氧协同作用下生成CO2卧式吸附态Ni(Ⅱ)←O-(CO)←(O--Ni).丙烯有多种吸附态在催化剂上吸附.在563 K、 1 MPa和空速1500 h-1的反应条件下,丙烯的摩尔转化率为3.2%,产物MAA选择性为95%.     

Toward new camptothecins. Part 6: Synthesis of crucial ketones and their use in Friedländer reaction

In the context of the preparation of camptothecin and luotonin A analogs, the synthesis of some key keto-precursors and their use in Friedländer condensation are described. This paper also focuses on the stability of these keto intermediates and emphasizes the major differences between indolizinones and pyrroloquinazolinones series. Noteworthy is also the report of some original structures isolated as by-products of some experiments.     

Synthesis of 1-benzyloxypyrazin-2(1H)-one derivatives

Different approaches for the synthesis of 1-benzyloxypyrazin-2(1H)-one derivatives from simple amino acids have been investigated. A library of 33 precursors for the preparation of N-hydroxy pyrazinones was obtained in moderate to good yields.     

CoFe2O4自形成磁性液体场致结构化对磁化的影响

The Langevin paramagnetic theory can’t describe the relation between magnetization of ferrofluids and applied magnetic field. The structuralization of ferrofluids, which is considered the main influence factor of the magnetization, is regarded. The part of magnetization works is deposited when the structure is forming. This action influences the magnetization of ferrofluids directly or indirectly. On the base of the “compressing” model, the Langevin function that usually describes the magnetization of ferrofluid is modified, and a well-fitted curve is obtained. An equation of the relation between the equivalent volume fraction after being “compressed” and the intensity of magnetic field is discovered, which approximately describes the process of magnetization. The relation between the approximate initial susceptibility and the volume fraction can be obtained from modified formula.     

Highly regioselective Buchwald–Hartwig amination at C-2 of 2,4-dichloropyridine enabling a novel approach to 2,4-bisanilinopyridine (BAPyd) libraries

The highly regioselective Buchwald–Hartwig amination at C-2 of the cheap and readily accessible reagent, 2,4-dichloropyridine with a range of anilines and heterocyclic amines is described. This new methodology is robust and provides a facile access to 4-chloro-N-phenylpyridin-2-amines on 0.25 mol scale. These intermediates undergo a further Buchwald–Hartwig amination at higher temperature to enable rapid exploration of the chemical space at C-4 and to provide a library of 2,4-bisaminopyridines.     

KMnO4-mediated oxidative CN bond cleavage of tertiary amines: Synthesis of amides and sulfonamides

KMnO₄-mediated oxidative CN bond cleavage of tertiary amines producing secondary amine was introduced, which was trapped by electrophiles (acyl chloride and sulfonyl chloride) to form amides and sulfonamides. The reaction could take place at mild condition, tolerating a wide range of function groups and affording products in moderate to excellent yields.     

Chemistry of heterocyclic compounds at the A. E. Favorsky Irkutsk Institute of Chemistry, Siberian Branch of the Russian Academy of Sciences, over 50 years (Review)

The review contains a concise historical account and information on the most significant researches undertaken by the staff at the A. E. Favorsky Irkutsk Institute of Chemistry, Siberian Branch of the Russian Academy of Sciences on the Chemistry of Heterocyclic Compounds. Dedicated to Academician of the Russian Academy of Sciences B. A. Trofimov on his 70th jubilee. Translated from Khimiya Geterotsiklicheskikh Soedinenii, No. 10, pp. 1443–1502, October, 2008.     

Sulfur-directed metal-free and regiospecific methyl C(sp3)–H imidation of thioanisoles

Regiospecific and direct imidation of the methyl C(sp³)–H bond of thioanisoles is realized under mild and metal-free conditions with N-fluorobis(benzenesulfonyl)imide as an oxidant and nitrogen source. Proposed mechanism suggests that thionium ion intermediates and a Pummerer-type reaction are involved. The imidation has advantages such as high step-economy, excellent functionality tolerance, and regiospecificity, giving structurally diverse imidation products.     

A general and convenient synthesis of 4-(tosylmethyl)semicarbazones and their use in amidoalkylation of hydrogen,heteroatom, and carbon nucleophiles

A general synthesis of previously unknown semicarbazone-based α-amidoalkylating reagents, 4-(tosylmethyl)semicarbazones, has been developed. The synthesis involved three-component condensation of semicarbazones of aliphatic or aromatic aldehydes with the same or other aldehydes and p-toluenesulfinic acid. The scope and limitations of this reaction were investigated. The compounds obtained were demonstrated to be an efficient α-(4-semicarbazono)alkylating agents. They were reacted with H- (sodium borohydride), O- (sodium methylate), S- (sodium phenylthiolate), N- (pyrrolidine, sodium succinimide), P- (trialkyl phosphites), and C-nucleophiles (sodium diethyl malonate) to give the corresponding products of the tosyl group substitution, 4-substituted semicarbazones, including analogues of nitrofurazone. Among the prepared compounds tested in vitro for antibacterial and antifungal activity, three nitrofuryl-containing semicarbazones exhibited high biological activities with minimum inhibitory concentration (MIC) values of 8–32 μg/mL.     

Synthesis of novel chiral bidentate hydroxyalkyl-N-heterocyclic carbene ligands and their application in palladium-catalyzed Mizoroki–Heck couplings and asymmetric addition of diethylzinc to benzaldehyde

A small library of new chiral bidentate hydroxyalkyl-imidazolium salts 1 is conveniently synthesized on multi-gram scale from inexpensive and commercially available chiral pool amino acids. The corresponding carbenes, generated by deprotonation of imidazolium salts 1, in combination with palladium(II) chloride were tested in the Mizoroki–Heck coupling reaction. The most significant results in terms of yields and reactivities were achieved with low catalyst loading. The catalytic activities of these imidazolium salts were also investigated in the asymmetric addition of diethylzinc to benzaldehyde. The use of MgO nanoparticles as an additive in conjunction with these ligands played a crucial role in increasing the efficiency of these reactions.