全硅沸石上有机吸附物亲和性指数的研究

用热分析技术，研究含有不同官能团的有机吸附质分子如：直链烷烃、直链烷 基胺、直链烷基醇等，在结构完美全硅FER,MFI, FAU沸石孔道中的程序升温脱附行 为，测定它们在这些沸石上的吸附量及亲和性指数A_T值，研究孔道半径对亲和性 指数A_T值的影响。结果表明，与沸石Si-O骨架“亲”性强的吸附质的Ar值，随孔 道半径的减小而降低；“憎”性强的的吸附质的Ar值与孔道半径的关系，则呈相反 趋势。     

用TG/DTG/DTA研究硅沸石与有机分子的主体/客体相互作用

用TG/DTA/DTA法研究无阳离子与Si-OH缺陷、结构完美的硅沸石上烃类、烷基醇、烷基胺的热脱附行为。有机分子从硅沸石上脱附的温度低于300℃。其亲和性值AT=Td-Tb, 式中Td为有机分子在DTG上的失重峰温, Tb为该有机物在标准压力下的沸点。饱和烷烃的AT值为60~90, 而苯、甲苯、对二甲苯等的AT值为6~13。电负性较强的羟基使烷基醇与硅沸石的亲和性明显下降。多羟基醇的AT值为负值。对二甲苯、烷基醇、烷基胺在脱附时有明显吸热效应。AT值及脱附热效应的不同是硅沸石骨架O^2^-微孔表面与有机分子C-H基团, 其它极性基团之间相互作用不同, 以及受到硅沸石骨架空间限制的被吸附分子间缔合情况下同所致, 反应了不同类型的主体/客体超分子相互作用。     

完美骨架全硅β沸石性质研究

运用热分析技术研究胺类、烷烃类、芳香烃类、醇类在具完美骨架的合成得到 的全硅β沸石中的脱附行为，测定亲和性指娄A_T值和负载量。发现烷烃类、胺类 、芳香族化合物都对全硅β沸石骨架表现出亲和性，而醇类由于羟基的存在表现出 对骨架的憎性，结合吸附热等数据讨论了各类吸附质与骨架相互作用（主／客体相 互作用）的性质。     

完美骨架全硅β沸石性质研究

运用热分析技术研究胺类、烷烃类、芳香烃类、醇类在具完美骨架的合成得到 的全硅β沸石中的脱附行为，测定亲和性指娄A_T值和负载量。发现烷烃类、胺类 、芳香族化合物都对全硅β沸石骨架表现出亲和性，而醇类由于羟基的存在表现出 对骨架的憎性，结合吸附热等数据讨论了各类吸附质与骨架相互作用（主／客体相 互作用）的性质。     

用TG/DTG/DTA研究硅沸石与有机分子的主体/客体相互作用

用TG/DTG/DTA法研究无阳离子与Si—OH缺陷、结构完美的硅沸石上烃类、烷基醇、烷基胺的热脱附行为.有机分子从硅沸石上脱附的温度低于300℃其亲和性值A_T=T_d-T_b,式中T_d为有机分子在DTG上的失重峰温,T_b为该有机物在标准压力下的沸点.饱和烷烃的A_T值为60～90,而苯、甲苯、对二甲苯等的A_T值为6～13.电负性较强的羟基使烷基醇与硅沸石的亲和性明显下降.多羟基醇的A_T值为负值.对二甲苯、烷基醇、烷基胺在脱附时有明显吸热效应.A_T值及脱附热效应的不同是硅沸石骨架0~(2-)微孔表面与有机分子C—H基因,其它极性基因之间相互作用不同,以及受到硅沸石骨架空间限制的被吸附分子间缔合情况不同所致,反应了不同类型的主体/客体超分子相互作用.     

高硅FAU沸石与甲胺吸附物的相互作用

合成高硅沸石中所用的模板剂胺类分子与沸石骨架 Si—O基团间的相互作用机理尚不清楚 .迄今为止 ,沸石与吸附胺之间的相互作用的研究还只限于测定沸石酸性质 [1,2 ]、表面羟基活性位或了解模板分子在沸石骨架中的位置和状态 [3,4 ] .甲胺、乙胺在骨架完美的高硅 FAU(Y型 )沸石上的亲和性指数 AT 值 ,即被吸附有机物脱附峰温与该有机物的沸点之差分别高达 1 60与 1 5 0℃[5] .而在高硅 MFI(Silicalite-1 )沸石上为 1 60与 1 2 7℃ [6 ] .与大多数有机物不同 ,被吸附的胺类脱附时的吸热效应十分明显 .上述现象表明胺与高硅沸石骨架 O2 -…     

硅沸石完美骨架上的吸附Ⅱ.乙胺、正戊烷、乙醇在 FAU型沸石上的吸附热

用测定吸附等温线法研究乙胺、正戊烷和乙醇在疏水高硅FAU沸石上的吸附热效应。根据Clapeyron-Clausius方程,处理吸附等温线,得到不同覆盖度C(C=被吸附分子数/晶胞)的等量吸附热Qst(C)(一定覆盖度C时由Clapeyron-Clausius方程计算的吸附热)及平均等量吸附热Qst^*(一定温度区间里等量吸附热Qst的平均值),以及Qst^*与沸点蒸发热△Hv的差值△H1(定义为相互作用强度△H1=Qst^*-△Hv)。所研究的三种有机分子的△H1的次序为△H1(乙胺)>△H1(正戊烷)>>△H1(乙醇)。这与AT值(定义为脱附温度Td与吸附质的沸点温度Tb的差值,无需单位)有正相关关系。由AT值观察到的高硅FAU沸石Si-O骨架与被吸附乙胺之间可能存在的强相互作用、为本研究测定的热力学定量数据△H1值所证明。     

FER型沸石的合成、结构与吸附性质

在TMEDA(四甲基乙基二胺)-Na2O-SiO2-Al2O3-H2O体系(I),Na2O-K2O-Al2O3-SiO2-H2O-HCO3^--CO3^2^-体系(II)及Py(吡啶)-PrNH2(正丙胺)-HF-SiO2-H2O体系(III)中, 分别合成了纯相FER沸石及FER硅沸石。用粉末XRD, FT-IR, 29Si MAS NMR及TG/DTA等表征其结构性质, 并用超微量电子真空吸附天平测定这些沸石样品对正己烷, 甲醇和水的吸附等温线。结果表明: 各体系合成的样品虽然结晶度高, 呈现出FER沸石的典型结构特征, 但由于它们的组成和晶格微结构不同, 热稳定性与吸附性质有明显的差异。在(I)体系中合成的FER沸石层错缺陷少, 晶格完美, 正己烷与甲醇的吸附量可达到理论值, 结构破坏温度为1190℃。红外精细谱及29Si MAS NMR高分辨谱证明FER硅沸石具有十分完美的骨架结构。由于晶胞收缩, 它对正己烷与甲醇吸附量略低于理论值, 并呈现出高度的疏水性。它的结构破坏温度高于1300℃。在(II)体系中合成的FER型沸石结构缺陷多, 沸石孔中的钾离子不易被质子完全交换。它的正己烷与甲醇吸附量均较低, 而水的吸附量相对较高。吸附现象表明, 正己烷和甲醇都被吸附于FER沸石的十元环主孔道中, 分压较高时, 甲醇可通过八元环进入小笼, 而水的吸附性质则主要与各样品的Si-OH缺陷及骨架中的阳离子含量有关。     

完善骨架全硅β沸石性质研究

以四乙基氢氧化铵为模板剂,正硅酸乙酯为硅源,静置水热法合成全硅β沸石 。用硝酸(13 mol/L)对硅铝比(Si/Al)为20的Na-β沸石回流脱铝。焙烧后的上述两 样品经粉末X射线衍射、低温氮吸附、核磁共振、红外光谱、吸附等温线等表征, 发现合成的全硅β沸石骨架与孔道结构完善并具有很高的表面疏水／亲有机物的吸 附特性。     

完善骨架全硅β沸石性质研究

以四乙基氢氧化铵为模板剂，正硅酸乙酯为硅源，静置水热法合成全硅β沸石 。用硝酸(13 mol/L)对硅铝比(Si/Al)为20的Na-β沸石回流脱铝。焙烧后的上述两 样品经粉末X射线衍射、低温氮吸附、核磁共振、红外光谱、吸附等温线等表征， 发现合成的全硅β沸石骨架与孔道结构完善并具有很高的表面疏水／亲有机物的吸 附特性。     

The leading role of association in framework modification of highly siliceous zeolites with adsorbed methylamine.

Affinity index (AT value), adsorption heat, X-ray diffraction (XRD), and 13C and 29Si magic-angle spinning (MAS) NMR, FTIR, and Raman spectroscopies were used to study the interaction of highly siliceous MFI-, FAU-, and FER-type zeolites with adsorbed methylamine (MA). Compared with the data for methanol, the much higher AT values and adsorption heats, and significant changes in XRD patterns, 29Si MAS NMR spectra, and FTIR spectra for the zeolites after adsorption of MA, revealed a strong hydrogen-bonding interaction between the perfect framework of the zeolites and the adsorbed MAs. This interaction results from the fact that the H atom of the amine group attacks the [Si-O] framework to form a Si-OHN bond, which leads to the appearance of Si-N bonds in the zeolites at 323 K. Therefore, the zeolite framework can be modified with MA under mild conditions. The highly siliceous MFI zeolite and the H-ZSM-5 zeolite with SiO2/Al2O3=31:1 were modified with MA and investigated by temperature-programmed desorption of CO2. The modified zeolites exhibited greatly enhanced basic properties in comparison with those of the raw materials. The influence of defects in the zeolite on the adsorption and the interaction with MA is discussed.     

The study of thiophene adsorption onto La(III)-exchanged zeolite NaY by FT-IR spectroscopy

Zeolites NaY and LaNaY (ion-exchanged with aqueous lanthanum nitrate solution) were used as adsorbents for removing organic sulfur compounds from model gasoline solutions (without and with toluene) and fluid catalytic cracked gasoline in fixed-bed adsorption equipment at room temperature and atmosphere pressure. The adsorptive selectivity for organic sulfur compounds was significantly increased when Na(+) ions in zeolite NaY were exchanged with lanthanum ions. IR spectra of thiophene adsorption indicate that thiophene is adsorbed onto La(3+) ions via direct S-La(3+) interaction and Na(+) ions via pi-electronic interaction for La(3+)-exchanged zeolite NaY, but only via pi-electronic interaction with Na(+) ions for NaY. The amount of adsorbed thiophene on La(3+)-exchanged zeolite Y was slightly decreased by coadsorption of benzene, but greatly reduced on NaY. The adsorption of thiophene via interaction with La(3+) on La(3+)-exchanged zeolite Y is hardly replaced by benzene coadsorption. The direct S-La(3+) interaction might be the essential reason for the evidently improved adsorptive selectivity of LaNaY for removing organic sulfur compounds from solutions containing large amount of aromatics.     

Controlled release of Ibuprofen from dealuminated faujasites

Four dealuminated faujasite samples have been employed as matrices for Ibuprofen adsorption and in vitro drug delivery with the aim of adapting the pore size to the size of the drug molecule and to study the influence of Al content upon the drug delivery. Ca. 15 wt% of Ibuprofen is adsorbed in the zeolite cavities. FTIR shows that the zeolite hydroxyl groups interact with Ibuprofen and, in addition, carboxylate species bonded to extraframework Al species are detected in the most dealuminated samples. Two stages are observed in the Ibuprofen delivery. In the first hours, the release is governed by a diffusion process, showing a similar delivery rate independently of the Al content. However, after this stage, the Al content is determinant in drug delivery, being the release faster when the framework Si/Al ratio increases up to 22, and then decreases for Si/Al=62. The behaviour of the highly dealuminated material is probably due to the predominance of Van der Waals interaction between the drug and the siliceous zeolite framework.     

Studies on the Formation and Characteristics of Two Types of p-Xylene/Silicalite-1 Associates

High resolution 29Si MAS NMR, 13C CPMAS NMR, and TG/DTG/DTA were used to study the interaction between theframework of siliceous MFI type zeolite (silicalite) and the adsorbedp-xylene. The zeolite sample used in this study possesses a perfectframework. A series of high resolution 29Si MAS NMR and 13CCP MAS NMR spectra of the samples with various loadings of p-xylene weremeasured. Experimental results of XRD, NMR and thermal analysis confirm theformation of two types of p-xylene/silicalite associate. The properties ofthe two types of associates are given in terms of their XRD patterns,NMR spectra and TG/DTG/DTA curves. When the p-xylene loading is lessthan four molecules per unit cell, the adsorbed molecules disperse inthe sinusoidal channels and interact with the framework O2-forming associate-I (p-xylene/silicalite), and inducing themonoclinic/orthorhombic(I) transition. When the p-xylene loadingis more than 5.2 molecules/u.c., the adsorbed p-xylene moleculesare located in the channel intersections and combined into ap-xylene/p-xylene complex via hydrogen bonding, formingassociate-II (p-xylene/p-xylene/silicalite) and inducingthe orthorhombic(I)/orthorhombic(II) transition. The desorptionof p-xylene from associate-II occurs at about 90 °Cwith an evident endothermic effect, whereas the desorption fromassociate-I occurs at about 140 °C without any visibleheat effect, implying that two types of sorption and desorptionprocesses exist in this host/guest system.     

Effects of adsorbate molecules on the quadrupolar interaction of framework aluminum atoms in dehydrated zeolite H,Na-Y

The effect of adsorbate molecules on the quadrupolar interaction of framework aluminum atoms with the electric field gradient in dehydrated zeolite H,Na-Y has been studied by (27)Al MAS NMR and (27)Al MQMAS NMR spectroscopy at magnetic fields of 9.4 and 17.6 T. Upon adsorption of molecules interacting with bridging OH groups by hydrogen bonds (acetonitrile and acetone), the quadrupole coupling constant of framework aluminum atoms was found to decrease from 16.0 MHz (unloaded zeolite) to 9.4 MHz. Adsorption of molecules, which cause a proton transfer from the zeolite framework to the adsorbates (ammonia and pyridine), reduces the quadrupole coupling constant to 3.8 MHz for coverages of 0.5-2 molecules per bridging OH group. The experiments indicate that the quadrupole coupling constant of framework aluminum atoms in dehydrated zeolite H,Na-Y reflects the chemical state of adsorbate complexes formed at bridging OH groups. In agreement with earlier investigations it was found that a proton affinity of the adsorbate molecules of PA = 812-854 kJ/mol is necessary to induce a proton transfer from the zeolite framework to the adsorbed compounds. This proton transfer is accompanied by a strong improvement of the tetrahedral symmetry of zeolitic framework AlO(4) tetrahedra and a decrease of the electric field gradient.     

镧改性提高ZSM-5分子筛水热稳定性

基于12T 团簇模型, 利用密度泛函理论(DFT)研究了ZSM-5 分子筛的水解脱铝机理以及镧改性提高ZSM-5分子筛水热稳定性的机理. 对未改性分子筛水解脱铝机理的研究表明, 首先是第一个水分子吸附在分子筛表面的酸性位上, 对分子筛的Al—O键起弱化作用, 使Al—O键伸长; 接着第二个水分子吸附到分子筛表面,分别与第一个水分子和分子筛骨架形成氢键, 进一步弱化与其最邻近的Al—O键, 并引致该键断裂. 同样, 其它的三个Al—O键也被削弱并逐一断裂, 从而发生分子筛水解脱铝现象. 引入的镧物种与分子筛骨架的四个O原子成键, 将铝包埋, 增加了分子筛孔壁厚度, 增大了水分子攻击铝的空间位阻, 抑制了水分子对Al—O键的弱化, 从而延缓Al—O键的断裂, 提高分子筛的水热稳定性. 计算的水分子吸附能和水解能进一步证实镧的引入提高了ZSM-5分子筛的水热稳定性.     

Theoretical Study of Ethanethiol Adsorption on HZSM-5 Zeolite

The density functional theory and the cluster model methods have been employed to investigate the interactions between ethanethiol and HZSM-5 zeolites. Molecular complexes formed by the adsorption of ethanethiol on silanol H3SiOH with two coordination forms, model Bronsted acid sites of zeolite cluster H3Si(OH)Al(OH)2SiH3 interaction with ethanethiol, aluminum species adsorbed ethanethiol have been comparatively studied. Full optimization and frequency analysis of all cluster models have been carried out using B3LYP hybrid method at 3-21G basis level for hydrogen atoms and 6-31G(d) basis set level for silicon, aluminum, oxygen, carbon, and sulfur atoms. The structures and energy changes of different coordination forms of H3Si(OH)Al(OH)2SiH3-ethanethiol, silanol-ethanethiol and Al(OH)3-ethanethiol have been studied. The calculated results showed the nature of interactions was van der Waals force as exhibited by not much change in geometric structures and properties. The preference order of ethanethiol adsorbed on HZSM-5 zeolite may be residual aluminum species, bridging hydroxyl groups and silanol OH groups from the adsorption heat. The adsorbed models of protonized ethanethiol on bridging hydroxyl OH groups and linear hydrogen bonded ethanethiol on bridging OH groups suggested in literature might not exist as revealed by this theoretical calculation. Possible adsorption models were obtained for the first time.