Non-doped phosphorescent white organic light-emitting devices with a quadruple-quantum-well structure

Non-doped white organic light-emitting devices (WOLEDs) with a quadruple-quantum-well structure were fabricated. An alternate layer of ultrathin blue and yellow iridium complexes was employed as the potential well layer, while potential barrier layers (PBLs) were chosen to be 2,2',2''-(1,3,5-benzenetriyl)-tris(1-phenyl-1-H-benzimidazole) (TPBi) or N,N'-dicarbazolyl-3,5-benzene (mCP) combined TPBi. On adjusting the PBLs for device performance comparison, the results showed that the device with all-TPBi PBLs exhibited a yellow emission with the color coordinates of (0.50,0.47) at a luminance of 1000 cd/m², while stable white emission with the color coordinates of (0.36,0.44) was observed in the device using mCP combined TPBi as the PBLs. Meanwhile, for the WOLED, with a reduced efficiency roll-off, a maximum luminance, luminous efficiency, and external quantum efficiency of 12,610 cd/m², 10.2 cd/A, and 4.4%, respectively, were achieved. The performance improvement by the introduction of mCP PBL was ascribed to the well confined exciton and the reduced exciton quenching effect in the multiple emission regions.     

High efficiency rubrene based inverted top-emission organic light emitting devices with a mixed single layer

Inverted top-emission organic light emitting devices (TEOLEDs) with a mixed single layer by mixing of electron transport materials (PyPySPyPy and Alq₃), hole transport material (α-NPD) and dope material (rubrene) were investigated. Maximum power efficiency of 3.5 lm/W and maximum luminance of 7000 cd/m² were obtained by optimizing the mixing ratio of PyPySPyPy:Alq₃:α-NPD:rubrene=25:50:25:1. Luminance and power efficiency of mixed single layer device were two times improved compared to bi-layer heterojunction device and tri-layer heterojunction device. Lifetime test also shows that the mixed single layer device exhibits longer operational lifetimes of 343 h, which is three times longer than the 109 h for tri-layer device, and two times longer than the 158 h for bi-layer device. In addition, the maximum luminance and power efficiency were obtained at 20,000 cd/m² and 7.5 lm/W, respectively, when a TPD layer of 45 nm was capped onto the top metal electrode.     

Silicon-on-insulator microcavity light emitting diodes with two Si/SiO2 Bragg reflectors

Light emitting pn-diodes were fabricated on a 5.8 μm thick n-type Si device layer of a silicon-on-insulator (SOI) wafer using standard silicon technology and boron implantation. The thickness of the Si device layer was reduced to 1.3 μm, corresponding to a 4λ-cavity for λ=1150 nm light. Electroluminescence spectra of these low Q-factor microcavities are presented. Addition of Si/SiO₂ Bragg reflectors on the top and bottom of the device (3.5 and 5.5 pairs, respectively) is predicted to lead to spectral emission enhancement by ∼270.     

Improved performances of red organic light-emitting devices by co-doping a rubrene derivative and DCJTB into tris-(8-hydroxyquinoline) aluminum host

Performances of red organic light-emitting device were improved by co-doping 2-formyl-5,6,11,12-tetraphenylnaphthacene (2FRb) and 4-(dicyanomethylene)-2-t-butyl-6-(1,1,7,7-tetra-methyljulolidyl-9-enyl)-4H-pyran (DCJTB) in tris-(8-hydroxyquinoline) aluminum (Alq₃) host as the emitting layer. The device with 1 wt% DCJTB and 2.4 w% 2FRb in Alq₃ host gave a saturated red emission with CIE chromaticity coordinates of (0.65, 0.35) and a maximum current efficiency as high as 6.45 cd/A, which are 2 and 2.4 fold larger than that of the device with 1 wt% DCJTB (3.28 cd/A) in Alq₃ host and the device with 2.4 wt% 2FRb (2.72 cd/A) in Alq₃ host at the current density of 20 mA/cm², respectively. The improvement could be attributed to the effective utilization of host energy by both energy transfer and trapping in the electroluminescence process and the depression of concentration quenching between the dopants molecules.     

Enhanced quantum efficiency in polymer electroluminescence devices by inserting an ultrathin PMMA layer

We report an increase of electroluminescence (EL) efficiency by about two times for poly(2-methoxy-5-(2′-ethylhexyloxy)-1,4-phenylene vinylene) (MEH-PPV) based polymer light-emitting diodes (PLED) while employing an ultrathin layer of poly(methyl methacrylate) (PMMA) between a hole injection layer, polyethylenedioxythiophenne:polystyrenesulfonate (PEDOT:PSS) and an emitting layer, MEH-PPV. The peak power efficiency of the control device (ITO/MEH-PPV/LiF/Al) was 0.42 lm/W with a current efficiency of 0.66 cd/A. The device with the optimized thickness of PMMA interface layer shows the highest power efficiency of 1.15 lm/W at a current efficiency exceeding 1.83 cd/A. The significant improvement in the device performance is attributed to the decrease of holes injection and the promotion of electrons injection, which cause the balance of the carriers within the emitting layer.     

Low driving voltage in white organic light-emitting diodes using an interfacial energy barrier free multilayer emitting structure

The driving voltage of white organic light-emitting diodes (WOLEDs) with blue fluorescent and red phosphorescent emitting materials was lowered by using a device architecture with little energy barrier between emitting layers. A mixed layer of hole and electron transport materials was used as a host material and an interlayer, reducing the driving voltage of WOLEDs. The driving voltage of WOLEDs was reduced by more than 4 V and power efficiency of WOLEDs was improved by more than 40% due to little energy barrier for holes and electrons injection in light-emitting layer. In addition, there was little change of electroluminescence spectra from 100 to 10,000 cd/m².     

The use of a perylenediimide derivative as a dopant in hole transport layer of an organic light emitting device

A perylene diimide (PDI) derivative was used as a dopant in the hole transport layer (HTL) of an organic light emitting device. The HTL examined was poly (N-vinylcarbazole) (PVK) and the PDI used was N,N′-di-dodecylperylene-3,4,9,10-bis-(dicarboximide), (N-DODEPER). The structure of the device was ITO/PEDOT:PSS (70 nm)/PVK:N-DODEPER(0, 0.2, 0.4, 0.8 wt.%) (65 nm)/Alq₃ (35 nm)/LiF (1.3 nm)/Al (100 nm). 0.8 wt.% N-DODEPER presence exhibited a luminous efficiency of 7.87 cd/A and an external quantum efficiency of 0.78% at 21 mA/cm² and a power efficiency of 3l m/W at 12 mA/cm². The luminous and power efficiency values were significantly enhanced by a factor of 15 with respect to that of undoped device.     

3,4,9,10-Perylenetetracarboxylicdiimide as an interlayer for ultraviolet organic light emitting diodes

Ultraviolet organic light emitting diodes with 3,4,9,10-perylenetetracarboxylicdiimide (PTCDI) interlayer have been achieved. The emission spectrum and intensity were strongly dependent on the thickness of PTCDI interlayer, in spite of the fact that PTCDI has neither much lower HOMO nor much higher LUMO level, which is considered necessary for efficient charge blocking layers. The influence of PTCDI layer was investigated in three different device configurations and obtained results are discussed. For optimal device configuration, OLED with emission centered at 370 nm and turn-on voltage of 4.5 V is obtained.     

Non-doped red to yellow organic light-emitting diodes with an ultrathin 4-(dicyanomethylene)-2-t-butyl-6(1,1,7,7-tetramethyljulolidyl-9-enyl)-4H-pyran (DCJTB) layer

In this letter, bright non-doped red to yellow organic light-emitting diodes (OLEDs) with ultrathin 4-(dicyanomethylene)-2-t-butyl-6(1,1,7,7-tetramethyljulolidyl-9-enyl)-4H-pyran (DCJTB) layer as the emitting layer were fabricated. It was investigated that the effect of the ultrathin DCJTB layer on the electroluminescent (EL) performance of OLEDs. The DCJTB layer was incorporated at different positions in the conventional tris(8-quinolinolato)-aluminum (AlQ)-based devices (ITO/NPB/AlQ/LiF/Al). The emission of DCJTB was dominative in the EL spectra of the devices, in which the position of 0.3 nm DCJTB layer was less than 10 nm from the NPB/AlQ interface. The EL peak emission of DCJTB shifted to blue side as DCJTB position moved gradually from AlQ to NPB layer. The highest brightness of the device with 0.3 nm DCJTB layer inserted into NPB reached 16,200 cd/m² at 15 V, with the CIE coordinates of (0.522, 0.439).     

Efficient white organic light-emitting diodes based on an orange iridium phosphorescent complex

Stable and efficient white light emission is obtained by mixing blue fluorescence and orange phosphorescence. The introduction of double exciton blocking layers brings about well confinement of both charge-carriers and excitons in the emission layer. By systematically adjusting blue fluorescent and orange phosphorescent emission layers thickness, carriers in emission zone are balanced, and electrically generated excitons can be efficiently utilized. One white device with power efficiency of 14.4 lm/W at 100 cd/m² has excellently stable spectra. The improvement of performance is attributed to efficient utilization of the excitons and more balance of charge-carriers in emission layer.     

Increased luminance of MEH-PPV and PFO based PLEDs by using salmon DNA as an electron blocking layer

The effect of salmon DNA-CTMA as an electron blocking layer (EBL) has been examined on the performance of MEH-PPV and PFO-based light emitting diodes. Though the turn-on voltage increases with incorporation of EBL, a significant increase in luminance and luminous efficiency for both the devices is observed. The EBL improves the device performance by blocking electrons at the EBL-polymer interface, thereby increasing the recombination probability of electrons and holes. The luminance of the MEH-PPV based Bio-LED increases to 100 cd/m² from 30 cd/m² while a corresponding increase for the PFO based LED is to 160 cd/m² from 80 cd/m² with and without EBL, respectively.     

Effect of SiO2/Si3N4 dielectric distributed Bragg reflectors (DDBRs) for Alq3/NPB thin-film resonant cavity organic light emitting diodes

In this article, we report on the effect of SiO₂/Si₃N₄ dielectric distributed Bragg reflectors (DDBRs) for Alq₃/NPB thin-film resonant cavity organic light emitting diode (RCOLED) in increasing the light output intensity and reducing the linewidth of spontaneous emission spectrum. The optimum DDBR number is found as 3 pairs. The device performance will be bad by further increasing or decreasing the number of DDBR. As compared to the conventional Alq₃/NPB thin-film organic light emitting diode (OLED), the Alq₃/NPB thin-film RCOLED with 3-pair DDBRs has the superior electrical and optical characteristics including a forward voltage of 6 V, a current efficiency of 3.4 cd/A, a luminance of 2715 cd/m² under the injection current density of 1000 A/m², and a full width at half maximum (FWHM) of 12 nm for emission spectrum over the 5-9 V bias range. These results represent that the Alq₃/NPB thin-film OLED with DDBRs shows a potential as the light source for plastic optical fiber (POF) communication system.     

Characterization of two-emitter WOLED with no additional blocking layer

In this paper, white organic light emitting diodes (WOLEDs) utilizing two primary-color emitters with no additional blocking layer are fabricated. With a structure of ITO/2TNATA (20 nm)/NPB (20 nm)/NPB: rubrene (2%) (10 nm)/ADN (30 nm)/Alq₃ (20 nm)/LiF (1 nm)/Al (100 nm), a white light with CIE coordinates of (0.344, 0.372) is generated at a current density of 30 mA/cm² and the electroluminescence (EL) spectra consist of two broad bands around 456 nm (ADN) and 556 nm (NPB:rubrene). The device shows the low turn-on voltage and bright white emission with a power efficiency of 2.3 lm/W at a luminance of 100 cd/m². Through control of the location of the recombination zone and energy transfer, a stable white light emission is achieved. The maximum color shift is less than 0.02 units on the 1931 CIE x,y chromaticity diagram. Given the spectral power distribution of WOLED, the parameters of a light source (chromaticity coordinate, CCT, CRI, and the luminous efficacy) can be calculated. A MATLAB program for this purpose is developed in this paper. Based on this, the design of WOLED for an illumination and display system using a white emitter with color filter arrays is discussed.     

Enhanced field emission and patterned emitter device fabrication of metal-tetracyanoquinodimethane nanowires array

Ag(TCNQ) and Cu(TCNQ) nanowires were synthesized via vapor-transport reaction method at a low temperature of 100 °C. Field emission properties of the as-obtained nanowires on ITO glass substrates were studied. The turn-on electric fields of Ag(TCNQ) and Cu(TCNQ) nanowires were 9.7 and 7.6 V/μm (with emission current of 10 μA/cm²), respectively. The turn-on electric fields of Ag(TCNQ) and Cu(TCNQ) nanowires decreased to 6 and 2.2 V/μm, and the emission current densities increased by two orders at a field of 8 V/μm with a homogeneous-like metal (e.g. Cu for Cu(TCNQ)) buffer layer to the substrate. The improved field emission is due to the better conduct in the nanowires/substrate interface and higher internal conductance of the nanowires. The patterned field emission cathode was then fabricated by localized growing M-TCNQ nanowires onto mask-deposited metal film buffer layer. The emission luminance was measured to be 810 cd/m² at a field of 8.5 V/μm.     

Efficient polymer white-light-emitting diodes with a single-emission layer of fluorescent polymer blend

Efficient polymer white-light-emitting diodes (WPLEDs) have been fabricated with a single layer of fluorescent polymer blend. The device structure consists of ITO/PEDOT/PVK/emissive layer/Ba/Al. The emissive layer is a blend of poly(9,9-dioctylfluorene) (PFO), phenyl-substituted PPV derivative (P-PPV) and a copolymer of 9,9-dioctylfluorene and 4,7-di(4-hexylthien-2-yl)-2,1,3-benzothiadiazole (PFO-DHTBT), which, respectively, emits blue, green and red light. The emission of pure and efficient white light was implemented by tuning the blend weight ratio of PFO: P-PPV: PFO-DHTBT to 96:4:0.4. The maximum current efficiency and luminance are, respectively, 7.6 cd/A at 6.7 V and 11930 cd/m² at 11.2 V. The CIE coordinates of white-light emission were stable with the drive voltages.     

Effect of host and interlayer structures on device performances of hybrid white organic light-emitting diodes

The effect of host and interlayer structures on device performances of hybrid white organic light emitting diodes was studied by changing the energy level of host and interlayer materials. A mixed layer of hole transport type and electron transport type materials was used as a host and an interlayer. In the red:green/interlayer/blue stacked structure, a red shift of emission color was observed by increasing the highest occupied molecular orbital of the electron transport type material in the mixed layer. An optimization of the device structure gave a high current efficiency of 32.4 cd/A with a color coordinate of (0.44, 0.45).     

Low temperature deposition of SrS:Cu,F ACTFEL device by electron beam evaporation

Photoluminescence (PL) and electroluminescence (EL) of SrS:Cu,F alternating current thin film electroluminescent (ACTFEL) device prepared by electron beam/thermal multi-source evaporation are presented. The active layer was grown at 380 °C and neither post-deposition annealing nor sulphur co-evaporation was performed. Two bands at 380 and 435 nm were present in the PL spectrum, which are suggested to be due to donor acceptor recombination. EL spectrum consisted of an additional band at 535 nm, which is attributed to Cu⁺ intracenter emission. The device exhibited yellowish white EL emission with chromaticity coordinates x=0.25, y=0.27 and low threshold voltage.     

Efficient small molecular and polymer organic devices using bis[2-(4-tert-butylphenyl)benzothiazolato-N,C′] iridium (III) (acetylacetonate) dye as emitter

Small molecular organic light-emitting diodes (MOLED) and polymer organic light-emitting diodes (POLED) were fabricated with yellow light emission phosphorescent dye bis[2-(4-tert-butylphenyl)benzothiazolato-N,C²′] iridium (III) (acetylacetonate) doped in different hosts. The electroluminescent (EL) spectra of both devices shown two peaks generated from iridium dye but the position of main peak changed and became broader for POLED. The maximum luminance of 10,500 cd/m² achieved at 12.5 V for MOLED is higher than maximum luminance of 9996 cd/m² at 20 V for POLED. The maximum power efficiency of small molecular device is 6.4 lm/W, which is higher than 2.3 lm/W of polymer device, but the efficiency of both devices will roll off at large current density.     

White organic light emitting diodes based on DCM dye sandwiched in 2-methyl-8-hydroxyquinolinolatolithium

Stable white electroluminescence (EL) has been achieved from organic LED, in which an ultrathin 4-(dicyanomethylene)-2-methyl-6-(p-dimethyl-aminostyryl)-4H-pyran (DCM) dye layer has been inserted in between two 2-methyl-8-hydroxyquinolinolatolithium [LiMeq] emitter layer and by optimizing the position of the DCM dye layer from the α-NPD/LiMeq interface. Electroluminescence spectra, current-voltage-luminescence (I-V-L) characteristics of the devices have been studied by changing the position of the dye layer. As the distance of DCM layer from α-NPD/LiMeq interface is increased, the intensity of host emission enhances rapidly. Introduction of thin layer of DCM in emissive layer increases the turn on voltage. The best Commission International de L’ Eclairage (CIE) coordinates i.e. (0.32, 0.33) were obtained with device structure ITO/α-NPD(30 nm) /LiMeq(10 nm)/DCM(1 nm)/LiMeq(25 nm)/BCP(6 nm)/Alq₃(28 nm)/LiF(1 nm)/Al(100 nm). The EL spectrum covers the whole visible spectra range 400-700 nm. The color rendering index (CRI) for our best white light (Device 4) is 47.4. The device shows very good color stability in terms of CIE coordinates with voltages. The maximum luminescence 1240 cd/m⁻² has been achieved at 19 V.     

Yellow phosphors coated with TiO2 for the enhancement of photoluminescence and thermal stability

In order to improve the phosphor efficiency of yellow emission of the phosphor-converted white light emitting diode (pcW-LED), the Ba²⁺ Mg²⁺ co-doped Sr₂SiO₄:Eu phosphors were synthesized and were coated with thin and uniform TiO₂. The TiO₂ layer with 20 nm was uniformly coated over the phosphor surface. The photoluminescence (PL) properties of the TiO₂-coated phosphors showed improved yellow-emission intensity compared to the pristine phosphors. The temperature dependence of photoluminescence was measured from 25 to 150 °C. The TiO₂-coated phosphors showed superior thermal quenching property compared to pristine phosphors. We concluded that the TiO₂-coated surface of the phosphor is an effective way to improve the phosphor efficiency and enhance the thermal quenching stability.