Photoluminescence characterization of Ce and Dy doped Li2CaGeO4 phosphors

Ce³⁺ and Dy³⁺ activated Li₂CaGeO₄ phosphors were prepared by a solid-state reaction method, and characterized by XRD (X-ray diffraction) and photoluminescence techniques. The characteristic emission bands of Dy³⁺ due to ⁴F_9/2→⁶H_15/2 (blue) and ⁴F_9/2→⁶H_13/2 (yellow) transitions were detected in the emission spectra of Li₂CaGeO₄:Dy³⁺. Ce³⁺ broad band emission was observed in Li₂CaGeO₄:Ce³⁺ phosphors at 372 and 400 nm due to 5d→4f transition when excited at 353 nm. Co-doping of Ce³⁺ enhanced the luminescence of Dy³⁺ significantly and concentration quenching occurs when Dy³⁺ is beyond 0.04 mol%. White-light with different hues can be realized by tuning Dy³⁺ concentration in the phosphors.     

Luminescence of Ce and Pr doped Sr2Mg(BO3)2 under VUV-UV and X-ray excitation

This report presents the luminescence properties of Ce³⁺ and Pr³⁺ activated Sr₂Mg(BO₃)₂ under VUV-UV and X-ray excitation. The five excitation bands of crystal field split 5d states are observed at about 46 729, 44 643, 41 667, 38 314 and 29 762 cm⁻¹ (i.e. 214, 224, 240, 261 and 336 nm) for Ce³⁺ in the host lattice. The doublet Ce³⁺ 5d→4f emission bands were found at about 25 840 and 24 096 cm⁻¹ (387 and 415 nm). The influence of doping concentration and temperature on the emission characteristics and the decay time of Ce³⁺ in Sr₂Mg(BO₃)₂ were investigated. For Pr³⁺ doped samples, the lowest 5d excitation band was observed at about 42017 cm⁻¹ (238 nm), a dominant band at around 35714 cm⁻¹ (280 nm) and two shoulder bands were seen in the emission spectra. The excitation and emission spectra of Ce³⁺ and Pr³⁺ were compared and discussed. The X-ray excited luminescence studies show that the light yields are ∼3200±230 and ∼1400±100 photons/MeV of absorbed X-ray energy for the samples Sr_1.86Ce_0.07Na_0.07Mg(BO₃)₂ and Sr_1.82Pr_0.09Na_0.09Mg(BO₃)₂ at RT, respectively.     

Energy transfer in Y3Al5O12:Ce, Pr and CaMoO4:Sm, Eu phosphors

Non-radiative energy transfers (ET) from Ce³⁺ to Pr³⁺ in Y₃Al₅O₁₂:Ce³⁺, Pr³⁺ and from Sm³⁺ to Eu³⁺ in CaMoO₄:Sm³⁺, Eu³⁺ are studied based on photoluminescence spectroscopy and fluorescence decay patterns. The result indicates an electric dipole-dipole interaction that governs ET in the LED phosphors. For Ce³⁺ concentration of 0.01 in YAG:Ce³⁺, Pr³⁺, the rate constant and critical distance are evaluated to be 4.5×10⁻³⁶ cm⁶ s⁻¹ and 0.81 nm, respectively. An increase in the red emission line of Pr³⁺ relative to the yellow emission band of Ce³⁺, on increasing Ce³⁺ concentration is observed. This behavior is attributed to the increase of spectral overlap integrals between Ce³⁺ emission and Pr³⁺ excitation due to the fact that the yellow band shifts to the red spectral side with increasing Ce³⁺ concentration. In CaMoO₄:Sm³⁺, Eu³⁺, Sm³⁺-Eu³⁺ transfer occurs from ⁴G_5/2 of Sm³⁺ to ⁵D₀ of Eu³⁺. The rate constant of 8.5×10⁻⁴⁰ cm⁶ s⁻¹ and the critical transfer distance of 0.89 nm are evaluated.     

Optical properties of blue emitting Ce activated XMg2Al16O27 (X = Ba, Sr) phosphors

Here we reported that the optical properties of novel blue-emitting Ce³⁺ activated XMg₂Al₁₆O₂₇ (X = Ba, Sr) phosphors were prepared by combustion method successfully. The excitation spectrum shows a broad band extending from 280 to 380 nm, centered at 355 nm, and the emission spectrum shows intense blue emission broad band centering at 441 nm for Ba²⁺ and Sr²⁺ host lattices. XRD pattern indicates crystalline nature of prepared phosphors. SEM analysis shows morphology of the ternary-hexaaluminate based phosphor prepared by combustion method. The Ce³⁺ activated XMg₂Al₁₆O₂₇ (X = Ba, Sr) should be a promising blue phosphor for near ultraviolet-based white-light-emitting diodes.     

Effect of Ce on the spectroscopic properties in Er doped TeO2-GeO2-Nb2O5-Li2O glasses

The Ce³⁺ ion was introduced into Er³⁺ doped TeO₂-GeO₂-Nb₂O₅-Li₂O (TGNL) glass to improve the 1.5 μm fluorescence characteristics. As increasing of Ce³⁺ concentration, the lifetime of Er³⁺:⁴I_11/2 level is shortened form 360 to 225 μs, while the Er³⁺:⁴I_13/2 level remains unchanged. Accordingly, the upconversion fluorescence (blue, green and red) was quenched. Improved 1.5 μm emission is obtained and the reason is ascribed to the increase of nonradiative rate between the ⁴I_11/2 and ⁴I_13/2 level of the Er³⁺ ions.     

Ca2BO3Cl:Ce,Eu: A potential tunable yellow-white-blue-emitting phosphors for white light-emitting diodes

Polycrystalline Ca₂BO₃Cl:Ce³⁺,Eu²⁺ phosphors were synthesized by a solid-state reaction and which could display tunable color emission from blue to yellow under an ultraviolet (UV) source by adjusting the ratio of Ce³⁺ and Eu²⁺ appropriately. The mechanism of resonance-type energy transfer from Ce³⁺ to Eu²⁺ was established to be electric dipole-dipole natured, and the critical distance was estimated to be 31 Å based on the spectral overlap and concentration quenching model. A white light was obtained from Ca₂BO₃Cl:0.06Ce³⁺,0.01Eu²⁺ phosphor with chromaticity coordinates (x=0.31, y=0.29) and relative color temperature of 7330 K upon excitation with 360 nm, which is potentially a good candidate as an UV-convertible phosphor for white light-emitting diodes (LEDs).     

Synthesis and characterization of Ce doped silica (SiO2) nanoparticles

A series of silica doped with different mol percentages of Ce³⁺ concentration was synthesized using a sol-gel method to determine the dependence of photoluminescence wavelengths and intensity on the concentrations of the dopants. Sol-gel glasses are porous networks that have been densified through chemical processing and heat treatment. Rare-earths (REs) are insoluble in silica; due to this insolubility RE ions in silicate glasses enter as network modifiers and compete for non-bridging oxygen in order to complete their coordination. The morphological, structural, thermal and optical properties of the phosphors were characterized by X-ray diffraction, scanning electron microscopy, UV-vis absorption, photoluminescence, thermogravimetric analyses and differential scanning calorimeter. Silica (SiO₂) gel containing Ce³⁺ ions was sputter coated with Au (gold) in order to monitor surface morphology of the samples. The highest emission intensity was found for the sample with a composition of 0.5 mol% Ce³⁺. Cerium doped silica glasses had broad blue emission corresponding to the ²D_3/2-²F_J transition at 448 nm but exhibited apparent concentration quenching above concentrations of 0.5 mol% Ce³⁺.     

Low-temperature high-resolution VUV spectroscopy of Ce doped LiYF4, LiLuF4 and LuF3 crystals

For LiYF₄:Ce³⁺, LiLuF₄:Ce³⁺ and LuF₃:Ce³⁺ crystals UV/visible emission and time-resolved VUV/UV excitation spectra were recorded at liquid helium temperature with spectral resolution of 0.1 nm for excitation spectra and better than 0.3 nm for emission spectra. Well resolved fine structures due to zero-phonon lines were clearly observed in both excitation and emission spectra for LiYF₄:Ce³⁺ and LiLuF₄:Ce³⁺. For LuF₃:Ce³⁺ crystal no fine structure was detected in the spectra even at the highest spectral resolution. Under the host excitation, the fine structure for high-energy emission band of Ce³⁺ (5d-²F_5/2) in LiLuF₄:Ce³⁺ becomes well pronounced because of weaker reabsorption effect, as compared to Ce³⁺ 4f-5d absorption, due to small penetration depth for exciting radiation. As a result the crystal-field splitting for ²F_7/2 and ²F_5/2 levels of Ce³⁺ in LiLuF₄ crystal was measured. First observation of zero-phonon lines at ∼81,550 and ∼82,900 cm⁻¹ as well as vibronic side bands due to interconfigurational 4f¹⁴-4f¹³5d transitions in Lu³⁺ is reported for excitation spectrum of LiLuF₄:Ce³⁺.     

Ce emission in hexagonal and orthorhombic phases of CaSO4

CaSO₄ exists in several phases. The most common phase of CaSO₄ is orthorhombic and reported Ce³⁺ emission corresponds to this phase. However, significant change in the emission of Ce³⁺ is observed when CaSO₄ crystallizes in hexagonal phases. The emission is observed at 354 nm as compared to the spilt band at 305 and 326 nm for the orthorhombic phase. The preparation procedure and photoluminescence spectra for orthorhombic and hexagonal phases are described in this paper.     

Synthesis and luminescence properties of Eu, Ce and Tb-activated Sr3La2(BO3)4 under UV excitation

The spectroscopic properties in UV-excitable range for the phosphors of Sr₃La₂(BO₃)₄:RE³⁺ (RE³⁺=Eu³⁺, Ce³⁺, Tb³⁺) were investigated. The phosphors were synthesized by conventional solid-state reactions. The photoluminescence (PL) spectra and commission international de I'Eclairage (CIE) coordinates of Sr₃La₂(BO₃)₄:RE³⁺ were investigated. The f-d transitions of Eu³⁺, Ce³⁺ and Tb³⁺ in the host lattices are assumed and corroborated. The PL and PL excitation (PLE) spectra indicate that the main emission wavelength of Sr₃La₂(BO₃)₄:Eu³⁺ is 611 nm, and Sr₃La₂(BO₃)₄:Ce³⁺ shows dominating emission peak at 425 nm, while Sr₃La₂(BO₃)₄:Tb³⁺ displays green emission at 487, 542, 582 and 620 nm. These phosphors were prepared by simple solid-state reaction at 1000 °C. There are lower reactive temperature and more convenient than commercial phosphors. The Sr₃La₂(BO₃)₄:Tb³⁺ applied to cold cathode fluorescent lamp was found to emit green light and have a major peak wavelength at around 542 nm. These phosphors may provide a new kind of luminescent materials under ultraviolet excitation.     

Heat-treatment-induced luminescence degradation in Tb-doped CePO4 nanorods

CePO₄:Tb nanorods were synthesized via a simple wet-chemical route. The as-synthesized CePO₄:Tb nanorods present high photoluminescence efficiency due to an efficient energy transfer form Ce³⁺ to Tb³⁺. However, heat treatment at 150 °C in air leads to a significant decrease of photoluminescence. X-ray photoelectron spectroscopy and excitation spectra revealed the oxidation of Ce³⁺ to Ce⁴⁺ in the heat-treatment process, which should be responsible for significant photoluminescence degradation due to the breakage of Ce³⁺→Tb³⁺ energy transfer. This conclusion is further supported by atmosphere and size effects of photoluminescence of CePO₄:Tb under the heat treatment.     

Optical character of Er/Yb co-doped P2O5-CaO-Na2O-Al2O3-AgO phosphate glass

The up-conversion (UC) and near infrared (NIR) luminescence of Er³⁺/Yb³⁺ co-doped phosphate glass are investigated. In the UC emission range, the 523 nm, 546 nm green emissions and the 659 nm red emission are observed. With the increasing pump power, the intensity ratios of I₅₂₃/I₆₅₉, I₅₄₆/I₆₅₉ and I₅₂₃/I₅₄₆ increase gradually. The phenomenon is reasonably interpreted by theoretical analysis based on steady state rate equations. The emission cross section of the infrared emission at 1546 nm is larger (about 6.7 × 10^− 21 cm²), which is suitable for making fiber amplifier.     

Effective energy transfer between Ceand Eu in CaAl2Si2O8 host under vacuum ultraviolet illumination

We presented the energy transfer from Ce³⁺ to Eu²⁺ in CaAl₂Si₂O₈ host. The Ce³⁺-doped CaAl₂Si₂O₈ phosphor had a strong emission band at 378 nm under the vacuum ultraviolet (VUV) light. This emission spectrum of Ce³⁺ well overlapped with the excitation spectrum of Eu²⁺ under the UV illumination. As a result, the energy transfer from Ce³⁺ to Eu²⁺ in CaAl₂Si₂O₈ matrix was observed under VUV excitation, which resulted in a significant enhancement of the emission peak intensity at 446 nm. More details about the luminescent properties were presented.     

Mn, Cr-co-doped MgAl2O4 phosphors for white LEDs

The Mn-, Cr-doped and Mn, Cr-co-doped MgAl₂O₄ powders have been synthesized via a gel-solid reaction method. Energy transfer from Mn²⁺ to Cr³⁺ has been observed for the first time in the co-doped MgAl₂O₄ phosphors. When excited with blue light with a wavelength of 450 nm at room temperature, both green emission from Mn²⁺ around 520 nm and red emission from Cr³⁺ around 675and 693 nm were generated. Moreover, the color of the emission can be modified by controlling the doping concentrations of Mn²⁺ and Cr³⁺. Therefore, MgAl₂O₄: Mn²⁺, Cr³⁺ could be used as a single-phased phosphor for white LED with a blue LED chip. The energy transfer in terms of Mn²⁺ to Cr³⁺ is determined by means of radiation and reabsorption.     

The effect of Mg ions on the photoluminescence of Ce-doped silica

In this paper, we report enhanced luminescence of Mg-co-doped silica gels, which were prepared by a sol-gel method. The total amount of Ce³⁺ ions was kept constant in this experiment at 0.5 mol% total doping. Structural, morphological, thermal, optical absorption and photoluminescence studies were employed. The XRD spectra show that all the samples are non-crystalline. Scanning electron microscopy (SEM) images show that the particles were in nano-range and spherical in shape. Differential scanning calorimetry (DSC) and thermal gravimetric analysis (TGA) of samples depict that the presence of dopant and co-dopant decreases the endothermic peak temperature; while Ce³⁺ increase the yield, Mg²⁺ reduces it. UV analyses revealed that the presence of Ce³⁺ ions increases transmittance but lowers absorbance of annealed silica xerogels, while that of Mg²⁺ ions reduces transmittance but increases absorbance. Luminescence intensities were compared for different gels with and without Mg particles by varying the different concentrations of Mg. Silica containing Mg²⁺ ions had broad blue emission due to energy transfer from Mg²⁺ to Ce³⁺, which is due to radiative recombination. An increase in luminescence intensity was observed as the Mg²⁺ to Ce³⁺ ratio increased for the range investigated.     

Crystal structure and photoluminescence of (Y1−xCex)2Si3O3N4

Oxonitridosilicate phosphors with compositions of (Y_1−xCe_x)₂Si₃O₃N₄ (x=0−0.2) have been synthesized by solid state reaction method. The structures and photoluminescence properties have been investigated. Ce³⁺ ions have substituted for Y³⁺ ions in the lattice. The emission and excitation spectra of these phosphors show the characteristic photoluminescence spectra of Ce³⁺ ions. Based on the analyses of the diffuse reflection spectra and the PL spectra, a systematic energy diagram of Ce³⁺ ion in the forbidden band of sample with x=0.02 is given. The best doping Ce content in these phosphors is ∼2 mol%. The quenching temperature is ∼405 K for the 2 mol% Ce content sample. The luminescence decay properties were investigated. The primary studies indicate that these phosphors are potential candidates for application in three-phosphor-converted white LEDs.     

Luminescence in trivalent rare earth activated Sr4Al2O7 phosphor

In this paper we report the combustion synthesis of trivalent rare-earth (RE³⁺ = Dy, Eu and Ce) activated Sr₄Al₂O₇ phosphor. The prepared phosphors were characterized by the X-ray powder diffraction (XRD) and photoluminescence (PL) techniques. Photoluminescence emission peaks of Sr₄Al₂O₇:Dy³⁺ phosphor at 474 nm and 578 nm in the blue and yellow region of the spectrum. The prepared Eu³⁺ doped phosphors were excited by 395 nm then we found that the characteristics emission of europium ions at 615 nm (⁵D₀?⁷F₂) and 592 nm (⁵D₀?⁷F₁). Photoluminescence (PL) peaks situated at wavelengths of 363 and 378 nm in the UV region under excitation at around 326 nm in the Sr₄Al₂O₇:Ce³⁺ phosphor.     

Luminescence of La3F3[Si3O9]:Ce

The luminescence properties of Ce³⁺ in La₃F₃[Si₃O₉] are reported. Excitation and emission bands corresponding to 4f¹→5d¹ transitions of Ce³⁺ were identified. The center of gravity of the 5d states lies at remarkable high energy (43.2×10³ cm⁻¹) for Ce³⁺ in a silicate compound. This high value is attributed to the combined oxygen/fluoride coordination of the Ce³⁺ ion. Emission from the lowest 4f5d level to the ²F_5/2 and ²F_7/2 levels was found at 32.4×10³ and 30.4×10³ cm⁻¹. These results are compared with literature data on silicates and fluorides. From the values found for Ce³⁺, predictions are made for the positions of the 4f5d bands of Pr³⁺ and Er³⁺ in La₃F₃[Si₃O₉]. For both ions, it is concluded that in this host lattice emission is expected from high lying 4fⁿ energy levels.     

Luminescence spectroscopy of the Bi single and dimer centers in Y3Al5O12:Bi single crystalline films

Luminescence of the Bi³⁺ single and dimer centers in UV and visible ranges is studied in YAG:Bi (0.13 and 0.27 at% of Bi, respectively) single crystalline films (SCFs), grown by liquid phase epitaxy from a Bi₂O₃ flux. The cathodoluminescence spectra, photoluminescence decays, and time-resolved spectra are measured under the excitation by accelerated electrons and synchrotron radiation with energies of 3.7 and 12 eV, respectively. The energy level structure of the Bi³⁺ single and dimer centers was determined. The UV luminescence of YAG:Bi SCF in the bands that peaked at 4.045 and 3.995 eV at 300 K is caused by radiative transitions of Bi³⁺ single and dimer centers, respectively. The excitation spectra of UV luminescence of Bi³⁺ single and dimer centers consist of two dominant bands, peaked at 4.7/4.315 and 5.7/6.15 eV, related to the ¹S₀→³P₁ (A band) and ¹S₀→ ¹P₁ (C-band) transitions of Bi³⁺ ions, respectively. The excitation bands that peaked at 7.0 and 7.09 eV are ascribed to excitons bound with the Bi³⁺ single and dimer centers, respectively. The visible luminescence of YAG:Bi SCF presents superposition of several wide emission bands peaking within the 3.125-2.57 eV range and is ascribed to different types of excitons localized around the Bi³⁺ single and dimer centers. Apart from the above mentioned A and C bands the excitation spectra of visible luminescence contain wide bands at 5.25, 5.93, and 6.85 eV ascribed to the O²⁻→Bi³⁺ and Bi³⁺→Bi⁴⁺ + e charge transfer transition (CTT) in Bi³⁺ single and dimer centers. The observed significant differences in the decay kinetics of visible luminescence under excitation in A and C bands of Bi³⁺ ions, CTT bands, and in the exciton and interband transitions confirm the radiative decay of different types of excitons localized around Bi³⁺ ions in the single and dimer centers.     

Thermoluminescent and stuctural properties of BaAl2O4:Eu,Nd,Gdphosphors prepared by combustion method

BaAl₂O₄:Eu²⁺,Nd³⁺,Gd³⁺ phosphors were prepared by a combustion method at different initiating temperatures (400–1200 °C), using urea as a comburent. The powders were annealed at different temperatures in the range of 400–1100 °C for 3 h. X-ray diffraction data show that the crystallinity of the BaAl₂O₄ structure greatly improved with increasing annealing temperature. Blue-green photoluminescence, with persistent/long afterglow, was observed at 498 nm. This emission was attributed to the 4f⁶5d¹–4f⁷ transitions of Eu²⁺ ions. The phosphorescence decay curves were obtained by irradiating the samples with a 365 nm UV light. The glow curves of the as-prepared and the annealed samples were investigated in this study. The thermoluminescent (TL) glow peaks of the samples prepared at 600 °C and 1200 °C were both stable at ∼72 °C suggesting that the traps responsible for the bands were fixed at this position irrespective of annealing temperature. These bands are at a similar position, which suggests that the traps responsible for these bands are similar. The rate of decay of the sample annealed at 600 °C was faster than that of the sample prepared at 1200 °C.