共查询到20条相似文献,搜索用时 10 毫秒
1.
2.
群速度色散会限制太赫兹量子级联激光器频率梳的稳定以及频谱宽度.对于太赫兹量子级联激光器频率梳,其色散主要由器件增益、波导损耗、材料损耗引起.研究基于4.2 THz量子级联激光器双面金属波导结构,通过建立德鲁德模型,利用有限元法计算了激光器的波导损耗;器件未钳制的增益由费米黄金定则计算得到,结合增益钳制效应,计算了器件子带电子跃迁吸收以及镜面损耗,得到了器件钳制后的增益;利用Kramers-Kronig关系得到了器件的增益、波导损耗、材料损耗引起的色散,结果表明器件的激射区域存在非常严重的色散(–8×10~5—8×10~5 fs~2/mm).同时,计算了一种基于Gires-Tournois干涉仪结构的色散,结果表明,该结构的色散具有周期性,可以用于太赫兹量子级联激光器的色散补偿. 相似文献
3.
We propose a scheme for long-distance quantum communication where the elementary entanglement is generated through two-photon interference and quantum swapping is performed through one-photon interference. Local “polarization” maximally entangled states of atomic ensembles are generated by absorbing a single photon from on-demand single-photon sources. This scheme is robust against phase fluctuations in the quantum channels, moreover speeds up long-distance high-fidelity entanglement generation rate. 相似文献
4.
5.
6.
We demonstrate a carrier-envelope phase-stabilized octave-spanning oscillator based on the monolithic scheme. A wide output spectrum extending from 480 nm to 1050 nm was generated directly from an all-chirped mirror Ti:sapphire laser. After several improvements, the carrier-envelope offset(CEO) beat frequency accessed nearly 60 d B under a resolution of 100 k Hz. Using a feedback system with 50-k Hz bandwidth, we compressed the residual phase noise to 55 mrad(integrated from 1 Hz to 1 MHz) for the stabilized CEO, corresponding to 23-as timing jitter at the central wavelength of790 nm. This is, to the best of our knowledge, the smallest timing jitter achieved among the existing octave-spanning laser based frequency combs. 相似文献
7.
Pump-induced carrier envelope offset frequency dynamics and stabilization of an Yb-doped fiber frequency comb
下载免费PDF全文
![点击此处可从《中国物理 B》网站下载免费的PDF全文](/ch/ext_images/free.gif)
In this paper, we demonstrate a carrier envelope phase-stabilized Yb-doped fiber frequency comb seeding by a nonlinear-polarization-evolution(NPE) mode-locked laser at a repetition rate of 60 MHz with a pulse duration of 191 fs.The pump-induced carrier envelope offset frequency( f0) nonlinear tuning is discussed and further explained by the spectrum shift of the laser pulse. Through the environmental noise suppression, the drift of the free-running f0 is reduced down to less than 3 MHz within an hour. By feedback control on the pump power with a self-made phase-lock loop(PLL)electronics the carrier envelope offset frequency is well phase-locked with a frequency jitter of 85 m Hz within an hour. 相似文献
8.
9.
利用光纤飞秒光频梳和外腔可调谐半导体激光器, 建立了一套双频He-Ne激光器频率测量系统. 选用铷钟作为系统的频率基准, 通过将外腔半导体激光锁定至光频梳使得其频率溯源至铷钟, 再利用外腔可调谐半导体激光与双频He-Ne激光器输出的正交偏振激光拍频, 同时测量两路正交偏振激光频率. 将可调谐半导体激光器锁定至光频梳第1894449个梳齿, 其绝对频率为473612190000.0±2.7 kHz, 相对不确定度为5.7×10-12. 对商品双频He-Ne激光器进行频率测量实验, 双频He-Ne激光器水平方向偏振激光频率均值为473612229934 kHz, 竖直方向偏振激光频率均值为473612232111 kHz, 平均时间为1024 s的相对Allan标准差为5.2×10-11, 频差均值为2.177 MHz, 标准偏差为2 kHz. 相似文献
10.
Precise determination of characteristic laser frequencies by an Er-doped fiber optical frequency comb
下载免费PDF全文
![点击此处可从《中国物理 B》网站下载免费的PDF全文](/ch/ext_images/free.gif)
Shiying Cao 《中国物理 B》2022,31(7):74207-074207
Femtosecond optical frequency combs correlate the microwave and optical frequencies accurately and coherently. Therefore, any optical frequency in visible to near-infrared region can be directly traced to a microwave frequency. As a result, the length unit "meter" is directly related to the time unit "second". This paper validates the capability of the national wavelength standards based on a home-made Er-doped fiber femtosecond optical frequency comb to measure the laser frequencies ranging from visible to near-infrared region. Optical frequency conversion in the femtosecond optical frequency comb is achieved by combining spectral broadening in a highly nonlinear fiber with a single-point frequency-doubling scheme. The signal-to-noise ratio of the beat notes between the femtosecond optical frequency comb and the lasers at 633, 698, 729, 780, 1064, and 1542 nm is better than 30 dB. The frequency instability of the above lasers is evaluated by using a hydrogen clock signal with a instability of better than 1×10-13 at 1-s averaging time. The measurement is further validated by measuring the absolute optical frequency of an iodine-stabilized 532-nm laser and an acetylene-stabilized 1542-nm laser. The results are within the uncertainty range of the international recommended values. Our results demonstrate the accurate optical frequency measurement of lasers at different frequencies using the femtosecond optical frequency comb, which is not only important for the precise and accurate traceability and calibration of the laser frequencies, but also provides technical support for establishing the national wavelength standards based on the femtosecond optical frequency comb. 相似文献
11.
A diode laser spectrometer at 634nm and absolute frequency measurements using optical frequency comb
下载免费PDF全文
![点击此处可从《中国物理 B》网站下载免费的PDF全文](/ch/ext_images/free.gif)
This paper reports that two identical external-cavity-diode-laser
(ECDL) based spectrometers are constructed at 634 nm referencing on
the hyperfine B-X transition R(80)8-4 of 127I2. The lasers
are stabilized on the Doppler-free absorption signals using the
third-harmonic detection technique. The instability of the
stabilized laser is measured to be 2.8×10-12 (after
1000 s) by counting the beat note between the two lasers. The
absolute optical frequency of the transition is, for the first time,
determined to be 472851936189.5 kHz by using an optical frequency
comb referenced on the microwave caesium atomic clock. The
uncertainty of the measurement is less than 4.9 kHz. 相似文献
12.
飞秒光学频率梳波长覆盖范围向可见光波长扩展对于碘稳频激光的绝对频率测量以及光钟研究中钟激光的绝对频率测量都具有十分重要的意义. 本文在自行研制掺Er光纤飞秒光学频率梳的基础上, 采用放大-倍频-扩谱的方案, 实现了激光输出波长向可见光波长的扩展. 掺Er光纤飞秒光学频率梳输出的一部分光激光脉冲, 功率约为8 mW, 首先经掺Er光纤放大器将功率提高到531 mW, 此后利用MgO: PPLN晶体倍频, 倍频后激光的功率为170 mW, 倍频效率为32%, 脉冲宽度为85 fs. 倍频后的激光通过光子晶体光纤进行光谱展宽. 通过优化入射光偏振状态可以实现波长覆盖500-1000 nm, 输出功率为85 mW, 耦合效率为50%. 采用小型化碘稳频532 nm Nd: YAG激光器输出激光与光学频率梳光谱展宽后的激光进行拍频可以获得30 dB的拍频信号. 覆盖可见光波长的掺Er光纤飞秒光学频率梳为可见光范围内激光的绝对频率测量提供了技术手段. 相似文献
13.
14.
We propose a novel scheme to generate optical frequency comb by using a two-stage generator based on Mach-Zehnder modulator and re-circulating frequency shifter. Based on the Mach-Zehnder modulator a light source including 2 flat and stable frequency spectrum lines is generated at the first stage, and the light source is then used as the seed light in the re-circulating frequency shifter loop at the second stage. The scheme can greatly reduce the accumulated noise of the system. Through theoretical analysis and simulation it is shown that the proposed theoretical model of the two-stage system is proved in good agreement with simulation results. 相似文献
15.
详细分析了光学频率梳光谱干涉的原理, 建立了较全面的光谱干涉的数学模型, 为实现绝对距离测量提供理论分析基础. 基于光谱干涉, 指出通过光谱干涉条纹的振荡频率, 即一次傅里叶变换, 可以实现绝对距离测量, 数值模拟结果表明, 最大测量误差为1.5 nm; 提出了一种等效的多波长并行零差干涉的方法, 分析了多波长并行零差干涉法的测距原理. 数值模拟结果表明, 多波长并行零差干涉法的最大误差为8.7 nm; 通过脉冲啁啾实现绝对测距, 分析了基于脉冲啁啾实现绝对测距的原理, 数值模拟结果表明, 最大测距误差为5.3 nm. 相似文献
16.
We present a fully stabilized Yb-fiber frequency comb locked to a microwave standard and an optical reference separately. The carrier-envelope offset frequency is generated by a standard f–2f interferometer with 40 dB signal-tonoise ratio. The offset frequency and the repetition rate are stabilized simultaneously to the radio frequency reference for more than 30 hours, and the fractional Allan deviation of the comb is the same as the microwave standard of 10-12 at 1 s.Alternatively, the comb is locked to an ultra-stable optical reference at 972 nm using an intracavity electro-optic modulator,exhibiting a residual integrated phase noise of 458 mrad(1 Hz–10 MHz) and an in-loop tracking stability of 1.77× 10-18 at 1 s, which is significantly raised by six orders comparing to the case locked to the microwave frequency standard. 相似文献
17.
实验利用商品光纤飞秒激光器,自行构建了一套完整的光学频率梳系统,并获得了约30 dB信噪比的系统频移(fceo)信号.实现了光频梳重复频率(frep)信号及系统频移(fceo)信号的高稳定度锁定,并通过实验验证了光频梳锁定的跟踪精度.基于此稳定光频梳完成了对1064 nm碘稳频Nd:YAG固体激光器的绝对频率测量.实验结果表明,frep的跟踪精度在100 s取样时间时优于3.7×10-14,测量得到的1064 nm激光器绝对频率为:281630111757362 Hz.这一测量结果与国际计量委员会(CIPM)给出的国际推荐值符合到不确定度之内.
关键词:
光纤光频梳
稳频
锁相技术
光学频率计量 相似文献
18.
An optical frequency comb generator (OFCG) at 1064 nm with a modulation frequency of 2 GHz is developed for an accurate optical frequency link between iodine absorption lines near 532 nm. With the OFCG, we have measured frequency differences between seventeen 127I2 transitions with a measurement uncertainty of about 240 Hz (relatively 4.3×10−13), which is mainly contributed from the frequency repeatability of iodine-stabilized Nd:YAG lasers. The measured transitions provide an attractive frequency reference network and are excellent candidates for the practical realization of the meter. 相似文献
19.
All polarization-maintaining Er:fiber-based optical frequency comb for frequency comparison of optical clocks
下载免费PDF全文
![点击此处可从《中国物理 B》网站下载免费的PDF全文](/ch/ext_images/free.gif)
We demonstrate an optical frequency comb (OFC) based on a turnkey mode-locked laser with a figure-9-shape structure and polarization-maintaining fibers, for the comparison of frequency among optical clocks with wavelengths of 698 nm, 729 nm, 1068 nm, and 1156 nm. We adopt a multi-branch approach in order to produce high power OFC signals at these specific wavelengths, enabling the signal-to-noise ratio of the beatnotes between the OFC and the clock lasers to exceed 30 dB at a resolution bandwidth of 300 kHz. This approach makes the supercontinuum spectra much easier to be generated than a single branch OFC. However, more out-of-loop fibers degrade the long-term frequency instability due to thermal drift. To minimize the thermal drift effect, we set the fiber lengths of different branches to be similar, and we stabilize the temperature as well. The out-of-loop frequency instability of the OFC due to the incoherence of the multi-branch is about 5.5×10-19 for 4000 s, while the in-loop frequency instability of fceo and that of fbeat are 7.5×10-18 for 1 s and 8.5×10-18 for 1 s, respectively. The turnkey OFC meets the requirement for the comparison of frequency between the best optical clocks. 相似文献