Effect of Mg and Ti doping on the luminescence of Y2O3:Eu

The Y₂O₃:Eu³⁺,Mg²⁺,Ti^IV materials (x_Eu: 0.02, x_Mg: 0.08, x_Ti: 0.04) were prepared by solid state reaction. The purity and crystal structure of the material was studied with the X-ray powder diffraction. Luminescence properties were studied in the UV-VUV range with the aid of synchrotron radiation. The emission of Y₂O₃:Eu³⁺,Mg²⁺,Ti^IV had a maximum at 612 nm (λ_exc: 250 nm) due to the ⁵D₀→⁷F₂ transition of Eu³⁺. The excitation spectra (λ_em: 612 nm) showed a broad band at 233 nm, due to the charge transfer transition between O²⁻ and Eu³⁺, and at 297 nm due to the Ti→Eu³⁺ energy transfer. Only very weak persistent luminescence was discovered. In the room and 10 K temperature excitation spectra, the line at 208 nm is due to the formation of a free exciton (FE) and a broad band at 199 nm was related to the valence-to-conduction band absorption of the Y₂O₃ host lattice. The absorption edge was ca. 205 nm giving 6.1 eV as the energy gap of Y₂O₃.     

An analysis of Y2O3:Eu thin films for thermographic phosphor applications

A comparative study of the luminescent properties of Y₂O₃:Eu³⁺ phosphor powders and thin films sputtered from targets prepared from combustion synthesized powders is reported. Thin films of (Y_0.96Eu_0.04)₂O₃ were deposited on silicon substrates. Films deposited at 600 °C had both monoclinic and cubic phases of Y₂O₃, which developed to an oriented cubic phase after annealing. Films and powders showed a linear dependence of the intensity of the ⁵D₇→⁷F₂ (611 nm) transition with temperature in the range 26-660 °C with an average rate of change of 1.8×10⁻⁴ °C⁻¹. The rate of change appears to be dependent on the Eu³⁺ concentration. This work shows that these thin films can be used as thermographic phosphors for remote temperature measurements.     

Eu/Tb ions co-doped white light luminescence Y2O3 phosphors

Y₂O₃:Eu³⁺, Tb³⁺ phosphors with white emission are prepared with different doping concentration of Eu³⁺ and Tb³⁺ ions and synthesizing temperatures from 750 to 950 °C by the co-precipitation method. The resulted phosphors were characterized by X-ray diffraction (XRD) and photoluminescence (PL) spectroscopy. The results of XRD indicate that the crystallinity of the synthesized samples increases with enhancing the firing temperature. The photoluminescence spectra indicate the Eu³⁺ and Tb³⁺ co-doped Y₂O₃ phosphors show five main emission peaks: three at 590, 611 and 629 nm originate from Eu³⁺ and two at 481 and 541 nm originate from Tb³⁺, under excitation of 250-320 nm irradition. The white light luminescence color could be changed by varying the excitation wavelength. Different concentrations of Eu³⁺ and Tb³⁺ ions were induced into the Y₂O₃ lattice and the energy transfer from Tb³⁺→Eu³⁺ ions in these phosphors was found. The Commission International de l’Eclairage (CIE) chromaticity shows that the Y₂O₃:Eu³⁺, Tb³⁺ phosphors can obtain an intense white emission.     

Preparation and luminescent properties of cubic Eu:Y2O3 nanocrystals and comparison to bulk Eu:Y2O3

Y₂O₃:Eu³⁺ nanocrystals were prepared by combustion synthesis. The particle size estimated by X-ray powder diffraction (XRD) was about 10 nm. A blue-shift of the charge-transfer (CT) band in excitation spectra was observed in Y₂O₃:Eu³⁺ nanocrystals compared with bulk Y₂O₃:Eu³⁺. The electronic structure of Y₂O₃ is calculated by density functional method and exchange and correlation have been treated by the generalized gradient approximation (GGA) within the scheme due to Perdew-Burke-Ernzerhof (PBE). The calculated results show that the energy centroid of 5d orbital in nanocrystal has increasing trend compared with that in the bulk material. The bond length and bond covalency are calculated by chemical bond theory. The bond lengths of Y₂O₃:Eu³⁺ nanocrystal are shorter than those of the bulk counterpart and the bond covalency of Y₂O₃:Eu³⁺ nanocrystal also has an increasing trend. By combining centroid shift and crystal-field splitting, the blue-shift of the CT band is interpreted.     

Effect of Eu,Tb codoping on the luminescent properties of Y2O3 nanorods

Red-emitting Y₂O₃:Eu³⁺ and green-emitting Y₂O₃:Tb³⁺ and Y₂O₃:Eu³⁺, Tb³⁺ nanorods were synthesized by hydrothermal method. Their structure and micromorphology have been analyzed by X-ray powder diffraction (XRD) and transmission electron microscopy (TEM). The photoluminescence (PL) property of Y₂O₃:Eu³⁺,Tb³⁺ phosphor was investigated. In the same host (Y₂O₃), upon excitation with ultraviolet (UV) irradiation, it is shown that there are strong emissions at around 610 and 545 nm corresponding to the forced electric dipole ⁵D₀-⁷F₂ transition of Eu³⁺ and ⁵D₄-⁷F₅ transition of Tb³⁺, respectively. Different qualities of Eu³⁺and Tb³⁺ ions are induced into the Y₂O₃ lattice. From the excitation spectrum, we speculate that there exists energy transfer from Tb³⁺ to Eu³⁺ ions .The emission color of powders reveals regular change in the separation of light emission. These powders can meet with the request of optical display material for different colors or can be potentially used as labels for biological molecules.     

Synthesis and Luminescent Properties of Nano-scale Y2Si2O7:Re3+ (Re=Eu, Tb) Phosphors via Sol-Gel Method

用溶胶凝胶方法制备了稀土离子掺杂的焦硅酸钇纳米粉末,并用XRD对不同温度处理的样品结构进行了表征,结果表明1000 ℃时产物成α-Y2Si2O7相,粒径约为27 nm,且掺杂离子的浓度并不影响样品的结构,测量了Eu3+和Tb3+离子掺杂的样品的激发谱和发射谱,并对其进行了分析．激发谱中真空紫外区对应基质的吸收,紫外区分别对应Tb3+的4f~5d的吸收Eu3+的电荷迁移带的吸收,对发光强度随掺杂离子浓度的变化关系也进行了讨论．对室温下的寿命进行了测量和分析．     

Optical spectroscopy of Ca3Sc2Si3O12, Ca3Y2Si3O12 and Ca3Lu2Si3O12 doped with Pr

The silicates Ca₃Sc₂Si₃O₁₂, Ca₃Y₂Si₃O₁₂ and Ca₃Lu₂Si₃O₁₂, both undoped and doped with Pr³⁺ ions, have been synthesized by solid-state reaction at high temperature. The luminescence spectroscopy and the excited state dynamics of the materials have been studied upon VUV and X-ray excitation using synchrotron radiation. All doped samples have shown efficient 5d-4f emission upon direct VUV excitation of 5d levels, but only Ca₃Sc₂Si₃O₁₂:Pr³⁺ shows luminescence upon interband VUV or X-ray excitation. The VUV excited emission spectra of Ca₃Y₂Si₃O₁₂:Pr³⁺ and Ca₃Lu₂Si₃O₁₂:Pr³⁺ show features attributed to emission from two distinct sites accommodating the Pr³⁺ dopant. The decay kinetics of the Pr³⁺ 5d-4f emission in Ca₃Sc₂Si₃O₁₂:Pr³⁺ upon VUV excitation across the band gap are characterized by decay times in the range 25-28 ns with no significant rise after the excitation pulse. They appear to be faster upon X-ray irradiation than for VUV excitation. Weak afterglow components are attributed to defect luminescence.     

Effects of Tb doping on the photoluminescence of Y2O3:Tb nanophosphors

The effects of Tb doping on the photoluminescence (PL) of Y₂O₃:Tb nanophosphors have been investigated. Nanophosphors were prepared by the glycine-nitrate solution combustion technique using yttria and terbia powders as precursors. PL excitation spectra at room temperature consist of two overlapping bands centered at 277 and 304 nm, whereas emission spectra comprise several groups of lines corresponding to the ⁵D₄→⁷F_J (J=1-6) 4f electronic transitions of the Tb⁺³ ions. A direct comparison of nanophosphor and bulk concentration-quenching curves was obtained by annealing the nanophosphor powder and converting it to bulk material without altering the Tb concentration. The peak in the nanophosphor concentration-quenching curve occurs at a concentration ∼3 times higher than that of the bulk.     

The properties of the Y2O3 films exposed at elevated temperature

Yttrium trioxide (Y₂O₃) thin films have been deposited on silicon (1 1 1) substrates by RF magnetron sputtering. The influences of thermal exposure at high temperature in air on the structure, the surface morphology, roughness, and the refractive index of the Y₂O₃ thin film were investigated by X-ray photoelectron spectroscopy (XPS), X-ray diffraction (XRD), atomic force microscopy (AFM), and spectroscopic ellipsometry (SE). The results indicate that chemical composition of the as-deposited Y₂O₃ film is apparently close to the stoichiometric ratio, and it has a cubic polycrystalline structure but the crystallinity is poor. The monoclinic and cubic phases can coexist in the Y₂O₃ film after thermal exposure to 900 °C, and the monoclinic phase disappears completely after 300 s exposure to 950 °C. The changes of the surface morphology, roughness, and the refractive index of the Y₂O₃ film are closely related to the crystal structure, the internal stress, and various defects influenced by thermal exposure temperature and time.     

Photoluminescence of Y2O3:Eu thin film phosphors by sol-gel deposition and rapid thermal annealing

Y₂O₃:Eu³⁺ phosphor films have been developed by using the sol-gel process. Comprehensive characterization methods such as Photoluminescent (PL) spectroscopy, X-ray diffraction (XRD) and Fourier Transform Infrared (FTIR) spectroscopy were used to characterize the Y₂O₃:Eu³⁺ phosphor films. In this experiment, the XRD profiles show that the Y₂O₃:Eu³⁺ phosphor films crystallization temperature and optimum annealing temperature occur at about 650 and 750 °C, respectively. The optimum dopant concentration is 12 mol% Eu³⁺ and the critical transfer distance (R_c) among Eu³⁺ ions is calculated to be about 0.84 nm. Vacuum environment is more efficient than oxygen and nitrogen to eliminate the OH content and hence yields higher luminescent phosphor films. The PL emission intensity of Y₂O₃:Eu³⁺ phosphor films is also dependent on the annealing time. It was found that the H₂O impurities were effectively eliminated after annealing time of 25 s at 750 °C in vacuum environment. From the experiment results, the schematic energy band diagram of Y₂O₃:Eu³⁺ phosphor films is constructed.     

La2O3对Yb:Y2O3透明陶瓷光谱性能的影响

研究了La₂O₃对Yb：Y₂O₃透明陶瓷光谱性能的影响，添加适量La₂O₃以后，Yb：Y₂O₃透明陶瓷的吸收峰和发射峰的位置不变，但由于La³⁺的离子半径大于Y³⁺的离子半径，在Y₂O₃中引入La³⁺离子后，导致Y₂O₃晶格常数变大，晶场强度变弱，同时降低了Y₂O₃晶体的有序度，致使发射峰强度有所下降，发射截面变小.过量的La₂O₃（x=0.16）造成Yb³⁺激活离子发射强度明显下降；其荧光寿命在添加La₂O₃后总体增大45%—60%. 关键词： 氧化镧 氧化钇 透明陶瓷 光谱性能     

X-ray photoelectron spectroscopy studies of Co-doped ZnO-Ga2O3-SiO2 nano-glass-ceramic composites

Co-doped ZnO-Ga₂O₃-SiO₂ nano-glass-ceramic composites were prepared by sol-gel method. X-ray diffraction patterns showed that the crystallization temperature was 800 °C. X-ray photoelectron spectroscopy (XPS) was used to study the effect of heat-treatment temperature on the electronic structure of Co-doped ZnO-Ga₂O₃-SiO₂ nano-glass-ceramic composites. The Zn (2p_3/2), Ga (2p_3/2) and O (1s) XPS spectra for the glass-ceramics heat-treated at 800-1000 °C could be deconvoluted into two peaks corresponding to these elements in glass network and in nanocrystals, respectively. The results indicate that the material is composed of an amorphous silicate network and ZnGa₂O₄ nanocrystalline particles. The amount of nanocrystals increases with the annealing temperature. The photoelectron peak of Si (2p) shifts to higher binding energy at higher annealing temperature, revealing the charge transfer from Si to O increased. The relationship between the microstructure of Co-doped ZnO-Ga₂O₃-SiO₂ sample and its absorption properties was discussed, and the suitable heat-treatment temperature was proposed.     

钇复合氧化物颜料的制备与表征

通过尿素分解法,把三价铬离子掺入到钇铝石榴石Y₃Al₅O₁₂中,采用共沉淀法制备出绿色颜料。扫描电镜测试表明产物颗粒直径在200 nm左右,用XRD测试复合氧化物的结晶相行为,确定主相是钇铝石榴石相,用紫外可见漫反射光谱测试掺杂离子的配位状态和电子跃迁行为,用色度学测试氧化物颜色特征。将复合氧化物颜料颗粒与高分子聚丙烯共混,熔体纺丝,并通过北京同步辐射X射线CT对制得的纤维加以测试,结果表明复合氧化物颜料在高分子基质中得到良好的分散。这种颜料性能稳定,对环境友好,为实现无水印染技术奠定基础,减少纺织印染工业中所排放的污水。     

Curie temperatures of Y3Fe5O12/Gd3Fe5O12 superlattices

The magneto-optical Kerr effects (MOKE) of epitaxial Y₃Fe₅O₁₂/Gd₃Ga₅O₁₂ (YIG/GGG) garnet superlattices grown on (1 1 1)GGG previously by pulsed laser deposition (PLD) were measured. A series of superlattices were investigated with the thickness of the ferrimagnetic YIG layer varied from six unit cells to only one unit cell while keeping the Curie paramagnetic GGG fixed at one unit cell. It was demonstrated that the ellipsometric technique employing photoelastic modulators (PEM) is sensitive enough to measure the MOKE signals of these ultrathin oxide samples. The Curie temperatures, determined by MOKE, are fit with a power law, yielding a shift exponent λ = 3.1 ± 1.2.     

Silica-coated Y2O3:Eu nanoparticles and their luminescence properties

Crystalline Y₂O₃:Eu is of paramount significance in rare earth materials and research on luminescence spectra. In this work, the nanocrystalline Y₂O₃:Eu was coated with silica by a facile solid state reaction method at room temperature. The transmission electron microscope (TEM) photographs showed that the prepared Y₂O₃:Eu particle is polycrystalline with the size of 20 nm, the size of silica-coated particle is about 25 nm. The XPS spectra indicated that the silica layer is likely to interact with Y₂O₃:Eu by a Si-O-Y chemical bond. The luminescence spectra showed that the intensity of ground samples is lower than that of unground ones, the intensity of silica-coated phosphors is higher than that of the ground samples, while almost the same as that of the unground ones. Therefore, the silica coating decreases the surface defects of nanoparticles of the nanocrystalline Y₂O₃:Eu, thus increasing their luminescent intensity.     

Multiplication of electronic excitations in nanophosphors Lu2O3:Eu and Lu2O3:Tb

Luminescence properties of Lu₂O₃:Eu³⁺ and Lu₂O₃:Tb³⁺ nanocrystalline powders with the particle size varying from 46 to 6 nm were studied under excitation by synchrotron radiation in the photon energy range (up to ∼22.5 eV) covering the region where the processes of multiplication of electronic excitation occur. It was found that the excitation spectra of Tb³⁺ emission from all Lu₂O₃:Tb³⁺ nanopowders have similar behavior, whereas the shape of the excitation spectra of Eu³⁺ emission from Lu₂O₃:Eu³⁺ nanopowders strongly depends on the particle size. The difference in the behavior of Lu₂O₃:Eu³⁺ and Lu₂O₃:Tb³⁺ nanophosphor systems was explained by different mechanisms of the energy transfer from the host to Eu³⁺ or Tb³⁺ ions (either the hole or electron recombination mechanism, respectively), which are differently influenced by losses of electronic excitations near the particle surface.     

Oxygen transfer processes in (La,Sr)MnO3/Y2O3-stabilized ZrO2 cathodes: an impedance spectroscopy study

Impedance spectroscopy was used to study the oxygen reaction kinetics of La_0.8Sr_0.2MnO₃ (LSM)-based electrodes on Y₂O₃-stabilized ZrO₂ (YSZ) electrolytes. Three types of electrodes were studied: pure LSM, LSM–YSZ composites, and LSM/LSM–YSZ bilayers. The electrodes were formed by spin coating and sintering on single-crystal YSZ substrates. Measurements were taken at temperatures ranging from 550 to 850°C and oxygen partial pressures from 1×10⁻³ to 1 atm. An arc whose resistance R_el had a high activation energy, E_a=1.61±0.05 eV, and a weak oxygen partial pressure dependence, (P_O2)^−1/6, was observed for the LSM electrodes. A similar arc was observed for LSM–YSZ electrodes, where R_el(P_O2)^−0.29 and the activation energy was 1.49±0.02 eV. The combination of a high activation energy and a weak P_O2 dependence was attributed to oxygen dissociation and adsorption rate-limiting steps for both types of electrodes. LSM–YSZ composite cathodes showed substantially lower overall interfacial resistance values than LSM, but exhibited an additional arc attributed to the resistance of YSZ grain boundaries within the LSM–YSZ. At 850°C and low P_O2, an additional arc was observed with size varying as (P_O2)^−0.80 for LSM and (P_O2)^−0.57 for LSM–YSZ, suggesting that diffusion had become an additional rate limiting step. Bilayer LSM/LSM–YSZ electrodes yielded results intermediate between LSM and LSM–YSZ. The results showed that most of the improvement in electrode performance was achieved for a LSM–YSZ layer only ≈2 μm thick. However, a decrease in the grain-boundary resistance would produce much better performance in thicker LSM–YSZ electrodes.     

Luminescent properties of SrAl2B2O7: Ce, Tb

By using metal nitrates as starting materials, SrAl₂B₂O₇: Tb³⁺ and SrAl₂B₂O₇: Ce³⁺, Tb³⁺ powder phosphors were prepared by sol-gel method. X-ray diffraction (XRD), photoluminescence excitation and emission, as well as kinetic decays were employed to characterize the resulting samples. The results show that energy transfers from Ce³⁺ to Tb³⁺ ions. The emission intensity of Tb³⁺ ions in SrAl₂B₂O₇ could be greatly intensified when Ce³⁺ ions are doped into SrAl₂B₂O₇: Tb³⁺. The decay times of SrAl₂B₂O₇: Tb³⁺ were prolonged when Ce³⁺ ions were doped. The doping of Ce³⁺ ions not only improved the luminescent intensity, but also made the materials gets stable luminescent properties.     

Photoluminescence and gamma-ray irradiation of SrAl2O4:Euand Y2O3:Eu phosphors

Y₂O₃:Eu³⁺ phosphor is a very attractive material for use as a red phosphor in many fields. SrAl₂O₄:Eu²⁺ belongs to long lasting phosphor (LLP) and it is a useful bluish-green luminescence material, which can also be a promising candidate as a simple and easy-to-use radiation detection element for visual display of two dimensional radiation distributions. In the present study, both these two kinds of phosphors were synthesized using high temperature solid state reactions. In our work, the influence of gamma-ray irradiation on the properties of these two kinds of phosphors was studied by comparing photoluminescence, brightness and the decay curve of unirradiated and gamma-ray-irradiated samples. Conclusions from the present work can be briefly summarized as follows. In irradiated samples, the brightness is decreased without sensible change in the wavelength distribution of the luminescence spectrum and in the decay kinetic upon gamma exposure. Moreover, the emission due to Eu³⁺→Eu²⁺ conversion in Y₂O₃:Eu³⁺ phosphors was not observed in our sample after irradiation to high exposure. Also the brightness of SrAl₂O₄:Eu²⁺ phosphor turned out to decrease after the exposition to ionizing radiation while the luminescence wavelength distribution remained unchanged. The reason for the effect of gamma-ray irradiation on the properties of phosphors is also discussed in the paper.     

Ag+掺杂的立方相Y2O3:Eu纳米晶体粉末发光强度研究

采用化学自燃烧法制备了不同Ag⁺掺杂浓度的Y₂O₃:Eu纳米晶体粉末样品(［Y³⁺］∶［Eu³⁺］∶［Ag⁺］=99∶1∶X，X=0—3.5×10^-2)，以及通过退火处理得到了相应的体材料.根据X射线衍射谱确定所得纳米和体材料样品均为纯立方相.实验表明在纳米尺寸样品中随着Ag离子浓度的增加，荧光发射强度随之增加，当X=2×10^-2时达到最大值，其发光强度比X=0时提高了近50%.当Ag离子浓度继续增加，样品发光强度保持不变.在相应的体材料样品中则没有观察到此现象.通过对各样品的发射光谱，激发光谱，X射线衍射图谱，透射电镜(TEM)照片和荧光衰减曲线的研究，分析了引起纳米样品荧光强度变化的原因是由于Ag离子与表面悬键氧结合，从而使这一无辐射通道阻断，使发光中心Eu³⁺的量子效率提高；Ag⁺的引入所带来的另一个效应是使激发更为有效.这两方面原因使发光效率得到了提高.