Novel phosphors of Eu, Tb or Bi activated Gd2GeO5

Novel phosphors of or Bi³⁺ doped Gd₂GeO₅ were synthesized and their photoluminescent and cathodoluminescent properties were investigated. (Gd_1−xEu_x)₂GeO₅ and (Gd_1−xTb_x)₂GeO₅ formed continuous solid solution in the range of x=0.0-1.0. Gd₂GeO₅:Eu³⁺ and Gd₂GeO₅:Bi³⁺ presented bright red and blue luminescence for both UV and cathode ray excitation, respectively. While Gd₂GeO₅:Tb³⁺ gave bright green cathodoluminescence. In all three phosphors, the energy transfer from Gd³⁺ to activators (e.g. or Bi³⁺) occurred.     

Preparation of a GdCaAl3O7 matrix by the non-hydrolytic sol-gel route

Due to their stable physical and chemical properties, inorganic matrices have been widely employed as hosts for lasers and phosphors. We have prepared a GdCaAl₃O₇ matrix by the non-hydrolytic sol-gel route and have investigated the influence of heating treatment on sample structure. Europium III chloride was added as a structural probe, and the structure was analyzed by thermal analyses (TG/DTA/DSC), X-ray diffraction (XRD), and photoluminescence (PL). The XRD analysis revealed that initial crystallization took place at 400 °C. The peaks corresponding to the GdCaAl₃O₇ and GdAlO₃ phases were observed at 800 and 1000 °C. PL data revealed the characteristic transition bands arising from the ⁵D₀→⁵F_J (J=0, 1, 2, 3, and 4) manifolds under maximum excitation at 275, 391 and 463 nm for all the samples. All the analyses gave evidence that this methodology leads to the formation of a GdCaAl₃O₇ phase.     

Excitation of thermoluminescence in Eu doped Ba0.12Sr0.88SO4 nanophosphor by low energy argon ions

In the present paper thermoluminescence properties of argon ions irradiated barium strontium mixed sulphate phosphor are reported. The Ba_0.12Sr_0.88SO₄ phosphor was prepared by chemical co-precipitation method. The X-ray diffraction study of prepared sample suggests orthorhombic structure with average grain size of 37 nm. The samples were irradiated with 1.2 MeV Argon ions at fluences varying between 10¹¹-10¹⁵ ions/cm². The argon ions penetrate to the depth of 1.89 μm and lose their energy mainly via electronic stopping. Due to ion irradiation, a large number of defects in the sample are formed. Thermoluminescence (TL) glow curves were recorded for each of the ion fluence. These curves exhibit one broad peak with maximum intensity at 498 K composed of three overlapping peaks. This indicates that different sets of traps are being activated within the particular temperature range each with its own value of activation energy (E) and frequency factor (s). The peaks were observed due to formation of trap levels by ion irradiation and subsequently activation of traps on thermal stimulation. The TL response of the nanophosphor is linear in the dose range 59 kGy-590 MGy. Kinetic parameters associated with the prominent peaks were calculated using glow curve deconvolution (GCD) and verified by different glow curve shape and sample heating rate methods.     

Fluorescence emission spectrum and energy transfer in Eu and Mn co-doped Ba2Ca(BO3)2 phosphors

Eu²⁺ and Mn²⁺ co-doped Ba₂Ca(BO₃)₂ phosphors yield two emission bands consisting of green and red components under the excitation of 360 nm, which shows a great potential for white LEDs. Effective energy transfer occurs in Eu²⁺/Mn²⁺ co-doped Ba₂Ca(BO₃)₂ host due to the large spectral overlap between the emission of Eu²⁺ and the excitation of Mn²⁺. The energy transfer from Eu²⁺ to Mn²⁺ is thoroughly investigated by their excitation, emission and photoluminescence decay behaviors, and is demonstrated to be via the dipole–quadrupole interaction.     

Eu activated M6AlP5O20 (M=Sr/Ba/Mg) novel red phosphors

Eu³⁺ activated M₆AlP₅O₂₀ (where M=Sr/Ba/Mg) phosphors prepared by combustion synthesis and the completion of the synthesis was confirm by XRD (X-ray diffraction) patterns. The surface morphology studied by scanning electron microscopy (SEM) and photoluminescence (PL) properties has been reported in this paper. The Eu³⁺ PL emission spectrum was observed in M₆AlP₅O₂₀ phosphors (where M=Sr/Ba/Mg) at 592 (orange) and 618 nm (red) region, the spectrum due to ⁵D₀→⁷F₁ and ⁵D₀→⁷F₂ transitions at mercury free excitation, respectively. Its considerable emission intensity under 350 nm excitations makes it possible candidate materials as red component of tricolor luminescence materials and for near ultra violet light emitting diode (n-UVLED) phosphors.     

Crystal structure and photoluminescence properties of Eu-activated Ba2LiB5O10 phosphors

A novel orange-yellow-emitting Ba₂LiB₅O₁₀:Eu²⁺ phosphor has been synthesized by traditional high temperature solid state reaction. A monoclinic crystal structure of Barium lithiumborates Ba₂LiB₅O₁₀ was verified by the investigation of X-ray diffraction (XRD). The compound crystallizes in the space group of P121/m1(11) (Z = 2) with the unit cell parameters a = 4.414(1) Å, b = 14.576(2) Å, c = 6.697(2) Å and β = 104.26(2)°. Barium and lithium atoms are located in distorted octahedral and tetrahedral oxygen coordinations, respectively. Upon around 365 nm excitation, the Eu²⁺-activated Ba₂LiB₅O₁₀ phosphors exhibit a single broad emission band with the maximum at about 587 nm, due to the 4f⁶5d → 4f⁷(8S_7/2) transition of Eu²⁺. This work investigates the relationship between luminescence properties and structural characterization of the Ba₂LiB₅O₁₀: Eu²⁺. This newly developed phosphor shows high potential as a phosphor conversion for white LED applications.     

Influence of Eu doping content on photoluminescence of Gd2O3:Eu phosphors prepared by liquid-phase reaction method

Europium-doped cubic Gd₂O₃:Eu³⁺ nanoparticles containing various activator content in the range of 5-15 wt% were synthesized by a liquid-phase reaction method to investigate the influence of Eu³⁺ loading on the optical properties of phosphors by using XRD, TEM, BET, spectrometer and fluorometer. The size of Gd₂O₃:Eu³⁺ powders was in the range 21-41 nm. The phosphors showed an initial increase in luminescence and then a subsequent decrease with further doping (above 10 wt%). The decay time was reduced with increasing Eu loading; however, it decreased significantly above the 10% Eu doping. From spectroscopic studies, the Eu³⁺ doping ion distribution was uniform and homogeneous up to the 10 wt% loading because no concentration quenching effect was observed. However, further Eu³⁺ doping above 10 wt% reduced the luminescence due to the concentration quenching effect, as deduced from the shortening of the decay time.     

Eu/Tb ions co-doped white light luminescence Y2O3 phosphors

Y₂O₃:Eu³⁺, Tb³⁺ phosphors with white emission are prepared with different doping concentration of Eu³⁺ and Tb³⁺ ions and synthesizing temperatures from 750 to 950 °C by the co-precipitation method. The resulted phosphors were characterized by X-ray diffraction (XRD) and photoluminescence (PL) spectroscopy. The results of XRD indicate that the crystallinity of the synthesized samples increases with enhancing the firing temperature. The photoluminescence spectra indicate the Eu³⁺ and Tb³⁺ co-doped Y₂O₃ phosphors show five main emission peaks: three at 590, 611 and 629 nm originate from Eu³⁺ and two at 481 and 541 nm originate from Tb³⁺, under excitation of 250-320 nm irradition. The white light luminescence color could be changed by varying the excitation wavelength. Different concentrations of Eu³⁺ and Tb³⁺ ions were induced into the Y₂O₃ lattice and the energy transfer from Tb³⁺→Eu³⁺ ions in these phosphors was found. The Commission International de l’Eclairage (CIE) chromaticity shows that the Y₂O₃:Eu³⁺, Tb³⁺ phosphors can obtain an intense white emission.     

Photoluminescence of cubic and monoclinic Gd2O3:Eu phosphors prepared by flame spray pyrolysis

In this paper, europium-doped gadolinium phosphor, which is a potentially bifunctional material with both fluorescent and magnetic properties, has been prepared in a one-step procedure via flame spray pyrolysis, and its crystal structure, morphology, and PL intensity were investigated. All the prepared phosphors were submicron-sized with spherical shapes and either a pure cubic or pure monoclinic phase. In order to observe the effects of temperature on the crystal phases of the prepared phosphors, we applied a H₂ vs. N₂/O₂ diffusion flame, with the maximum flame temperature ranging from T_max=1375 to 2050 K. The temperature profiles under various flame conditions are also reported herein to further elucidate the rapid synthesis process. The PL intensity in the cubic phase improved linearly with increasing flame temperature until the transition to a monoclinic phase. The peak of the photoluminescence(PL) spectrum from the phosphors prepared at T_max=1733 K in the cubic phase was narrower and twice as strong as the peak of the PL spectrum from the phosphors prepared at T_max=2050 K in the monoclinic phase. This paper provides important data showing the relationship between the synthesis temperature and the phase transition in Gd₂O₃:Eu in the continuous one-step use of flame spray pyrolysis.     

Luminescence properties of novel NaBa4(BO3)3:Ce, Eu phosphors

Novel Eu³⁺, Ce³⁺ activated NaBa₄(BO₃)₃ phosphors were synthesized by solid-state reactions. The excitation spectrum of NaBa₄(BO₃)₃:Ce³⁺ consists of an intense band peaking at 350 nm and a weak band in the higher energy side, and the emission spectrum exhibits a blue band with a maximum at about 420 nm. The Eu³⁺ emission in NaBa₄(BO₃)₃ consists of the transitions from ⁵D₀ to ⁷F_J, and the excitation spectrum consists of broad excitation band peaking at 270 nm and some intense narrow lines. The optimum doped concentration, the critical distance of the concentration quenching, and the fluorescence lifetime have also been investigated.     

Eu3+离子对Li2O-Na2O-B2O3物理和光学特性的影响

The lithium sodium borate glasses doped with Eu³⁺ ion are prepared using melt quenching technique, their structural and optical properties have been evaluated. The density of prepared glasses exhibits an inverse behavior to the molar volume ranging from 2.26 g/cm³ to 2.43 g/cm³ and 26.95 cm³ /mol to 26.20 cm³ /mol, respectively. The absence of sharp peaks in XRD patterns confirms the amorphous nature of the prepared glasses. The absorption spectra yield four transitions centered at 391 nm (⁷F₀→⁵L₆), 463 nm (⁷F₀→⁵D₂), 531 nm (⁷F₀→⁵D₁), and 582 nm (⁷F₀→⁵D₀). The most intense red luminescence is observed at 612 nm corresponding to ⁵D₀→⁷F₂ transition under 390 nm laser excitations.     

Photoluminescence analysis of α-Al2O3 powders doped with Eu and Eu ions

Alumina (Al₂O₃) powders doped with europium trivalent (Eu³⁺) were prepared by a low-temperature (∼280 °C) combustion synthesis technique. When the powder was heat treated at 1200 °C for 2 h in the presence of flowing ammonia (NH₃), α-Al₂O₃ crystalline ceramic powders was obtained. The analysis of the luminescence showed that Eu³⁺ was reduced to europium divalent (Eu²⁺) after the heat-treatment process. Under ultraviolet (UV) lamp excitation (λ=254 nm) these powders containing sub-microcrystalline structures present bright red (Al₂O₃:Eu³⁺) and green (Al₂O₃:Eu²⁺) luminescence indicating that this material is a potential candidate for applications in phosphor technology.     

Synthesis, characterization, and luminescent properties of Lu2O3:Eu phosphors

Eu-doped lutetia (Lu₂O₃:Eu) nano-phosphors were synthesized by the sol-gel combustion process from a mixed aqueous solution of europium and lutetium nitrates, using organic glycine as the fuel. Powder X-ray diffraction shows that cubic Lu₂O₃:Eu crystallites are directly obtained by the sol-gel combustion process without further calcination. Electron microscopy reveals that the as-prepared phosphors are agglomerated and have a fluffy, fine, and porous morphology, consisting of primary particle size of 8-10 nm. The excitation spectrum is characterized by three dominant bands centered at 395, 466, and 534 nm, respectively. Both the photoluminescent and radioluminescent spectra are very similar and exhibit intense emission peaks centered at 612 nm due to ⁵D₀→⁷F₂ transition of Eu³⁺ ions. The energy transfer from Lu₂O₃ host to Eu³⁺ activator is more efficient in the case of calcined phosphors than for the as-prepared phosphors due to their improved lattice perfection.     

Dielectric properties and magnetoelectric effect of (x)NiFe2O4+(1−x)Ba0.8Sr0.2TiO3 composites

Magnetoelectric composites of NiFe₂O₄ and Ba_0.8Sr_0.2TiO₃ were prepared using conventional double-sintering ceramic method. The phase formation of magnetoelectric composites was confirmed by XRD technique. Variation of dielectric constant and loss tangent at room temperature with frequency in the range 100 Hz-1 MHz has been studied. Also the variation of dielectric constant and loss tangent with temperature and composition at fixed frequencies of 1 kHz, 10 kHz, 100 kHz and 1 MHz is reported. The static value of the magnetoelectric conversion factor was measured as a function of intensity of the magnetic field. The ME voltage coefficient of about 430 μV/cm Oe was observed for 15% NiFe₂O₄+85% Ba_0.8Sr_0.2TiO₃ composite. All the samples show linear variation of magnetoelectric conversion in the presence of static magnetic field.     

Role of WO3 in structural and optical properties of WO3-Al2O3-PbO-B2O3 glasses

Glass samples of composition xAl₂O₃-20PbO-(80−x)B₂O₃ and xWO₃-xAl₂O₃-20PbO-(80−2x)B₂O₃ with x varying from 0% to 10% mole fraction are prepared by melt quench technique. The optical band gap decreases (from 3.21 to 2.37 eV) more for WO₃-Al₂O₃-PbO-B₂O₃ glasses with an addition of WO₃ content. The FTIR spectral studies have pointed out the conversion of structural units of BO₃ to BO₄ and WO₄ to WO₆ in these glasses. The increase in density from 4.51 to 5.80 g cm⁻³ for WO₃-Al₂O₃-PbO-B₂O₃ glasses is observed with an increase in WO₃ content. This is observed that the atomic structure changes more with the incorporation of WO₃. This is due to the formation of WO₆, WO₄ and BO₄ units.     

Effect of Eu contents on the structure and properties of BaLa2ZnO5:Eu phosphors

A series of Eu³⁺ doped BaLa₂ZnO₅ was prepared by a Pechini-type sol-gel method. The effect of Eu³⁺ concentration on the structure and the luminescent properties of the samples BaLa_2−xEu_xZnO₅ were investigated by powder X-ray diffraction (XRD) and photoluminescence (PL) spectra. The sample adopts the tetragonal or orthorhombic structure as the Eu³⁺ concentration reaches below 1.2 or over 1.6, respectively. The sample is a mixture of tetragonal and orthorhombic phases as the contents of dopants lie between 1.2 and 1.6. The phosphor offers the strongest red light as content of Eu³⁺ is 0.4. In addition, the crystallization processes of the complex precursors were examined by simultaneous thermogravimetry and differential thermal analysis (TG-DTA), and also the optimal heating temperature was investigated.     

Asymmetric electrical properties in Pt/Ba0.5Sr0.5Ti0.99Co0.01O3/Nb-doped SrTiO3 capacitors

Ba_0.5Sr_0.5Ti_0.99Co_0.01O₃ (BSTC) thin films have been fabricated with pulsed laser deposition on Nb-doped SrTiO₃ (STN) substrate. In Pt/BSTC/STN capacitor, we systematically investigated the capacitance, leakage current and polarization versus bias voltage characteristics, and found that curves of capacitance versus voltage and leakage current versus voltage were not symmetric, and polarization hysteresis loop exhibited large relaxation of the remnant polarization at negatively poled state. A detailed analysis of capacitance data demonstrated a difference of the built-in voltage between top Pt/BSTC interface (V_b,t=2.5 V) and bottom BSTC/STN interface (V_b,b=1.1 V). Such different built-in voltages lead to the presence of an internal electric field, which results in asymmetric electric characteristics in Pt/BSTC/STN capacitor.     

Luminescence and EPR studies of Eu doped BaAl12O19 blue light emitting phosphors

Europium doped BaAl₁₂O₁₉ powder phosphors have been synthesized by combustion process within few minutes. The phosphors have been characterized by XRD, SEM, FT-IR, EPR and PL techniques. The EPR spectrum exhibits an intense resonance signal at g=1.96 characteristic of Eu²⁺ ions. In addition to this two weak resonance signals have been observed at g=2.28 and g=4.86. The population of the spin levels (N) for the resonance signal at g=1.96 is calculated as a function of temperature. By post-treating the phosphor at 1350 °C under a reducing atmosphere, it is observed that the population of spin levels has been increased five times. The excitation spectrum shows a peak at 326 nm with a shoulder at 290 nm. Upon excitation at 326 nm, the emission spectrum exhibits a well defined broad band with maximum at 444 nm emitting a blue light corresponding to 4f⁶5d→4f⁷ transition. The luminescence intensity also has been enhanced to 60% by post-treating the phosphor at 1350 °C under a reducing atmosphere.     

Synthesis and luminescent properties of nanoparticles LaSrAl3O7:Eu, Tb

Phosphors of nanoparticles LaSrAl₃O₇:RE³⁺(REEu, Tb) have been prepared by a sol–gel method. The structure and luminescent properties of LaSrAl₃O₇:Eu³⁺ and LaSrAl₃O₇:Tb³⁺ phosphors were characterized by X-ray diffraction and atomic force microscopy (AFM), photoluminescence excitation and emission spectra were utilized. From X-ray diffraction (XRD) patterns, it is indicated that the phosphor LaSrAl₃O₇ forms without impurity phase at 900 °C. From atomic force microscopy (AFM) images, it is shown that the crystal size of the phosphores are about 60–80 nm. Upon excitation with UV irradiation, it is shown that there is a strong emission at around 617 nm corresponding to the forced electric dipole ⁵D₀–⁷F₂ transition of Eu³⁺, and at around 545 nm corresponding to the ⁵D₄–⁷F₅ transition of Tb³⁺. The dependence of photoluminescence intensity on Eu³⁺(or Tb³⁺) concentration and annealing temperature were also studied in detail.     

Luminescence properties of Ba2NaNb5O15 crystals activated with Sm, Eu, Tb or Dy ions

Single crystals of Ba₂NaNb₅O₁₅ (BNN) singly doped with Sm³⁺, Eu³⁺, Tb³⁺ or Dy³⁺ have been grown by means of the flux growth method. Their visible emission and excitation spectra and the decay profiles of the luminescence have been measured at room temperature. All spectral features are significantly inhomogeneously broadened in consequence of the structural disorder of the host and of the doping mechanisms. The analysis of the observed spectra allows formulating an hypothesis about the site occupancy of the active ions in the BNN lattice.