Patterned immobilization of biomolecules by using ion irradiation‐induced graft polymerization

A new method for biomolecular patterning based on ion irradiation‐induced graft polymerization was demonstrated in this study. Ion irradiation on a polymer surface resulted in the formation of active species, which was further used for surface‐initiated graft polymerization of acrylic acid. The results of the grafting study revealed that the surface graft polymerization using 20 vol % of acrylic acid on the poly(tetrafluoroethylene) (PTFE) film irradiated at the fluence of 1 × 10¹⁵ ions/cm² for 12 h was the optimum graft polymerization condition to achieve the maximum grafting degree. The results of the fluorescence microscopy also revealed that the optimum fluence to achieve the maximum fluorescence intensity was 1 × 10¹⁵ ions/cm². The grafting of acrylic acid on the PTFE surfaces was confirmed by a fluorescence labeling method. The grafted PTFE films were used for the immobilization of amine‐functionalized p‐DNA, followed by hybridization with fluorescently tagged c‐DNA. Biotin‐amine was also immobilized on the acrylic acid grafted PTFE surfaces. Successful biotin‐specific binding of streptavidin further confirmed the potential of this strategy for patterning of various biomolecules. © 2009 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 47: 6124–6134, 2009     

Preparation of solid alkaline fuel cell binders based on fluorinated poly(diallyldimethylammonium chloride)s [poly(DADMAC)] or poly(chlorotrifluoroethylene‐co‐DADMAC) copolymers

A membrane or an electrode binder to be used in a solid alkaline fuel cell (SAFC) needs to (i) be insoluble in both aqueous solutions and the required fuels, and (ii) exhibit an hydroxide ion conductivity. To achieve these goals, two pathways were employed: (i) one consists of the radical copolymerization of diallyldimethylammonium chloride (DADMAC) with chlorotrifluoroethylene (CTFE) while (ii) the other one is based on the counter‐ion exchange of a poly(DADMAC) by fluorinated anions. First, the radical copolymerization of CTFE with DADMAC under various experimental conditions was achieved in yields up to 85%, and DADMAC percentages in the copolymers were higher than those in the feed compositions. To obtain insoluble copolymers, high CTFE feed contents (>70 mol %) were required. The other route consisting in the partial replacement of the Cl^? counter‐ions in the water‐soluble poly(DADMAC) by bistrifluoromethanesulfonimide (TFSI^?) did confer the starting material insolubility in water while maintaining its conductivity. When the fluorinated poly(DADMAC) was obtained from concentrated solutions of fluorinated surfactant, it was observed that the amount of counter‐ions exchanged was difficult to control, which limits optimization. Nevertheless, under diluted conditions, membranes with ion exchange capacity up to 0.7 meq g^?1, and conductivities close to 1 mS cm^?1 were obtained. Although their conductivities were low, these membranes fulfill the requirements for a SAFC membrane in terms of solubility in DMSO, water insolubility, and thermal stability (T_d,10% > 320 °C). When used in a fuel cell, as a binder in the membrane‐electrode assembly (MEA), significant improvements were noted (+50% of the open circuit voltage, +580% in current density, and +540% in accessible power). © 2009 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 47: 2043–2058, 2009     

Synthesis of graft copolymers by combination of radical photopolymerization and iniferter process

Various PS‐based graft copolymers including polystyrene‐graft‐poly(methyl methacrylate) and poly(styrene‐graft‐poly(ethylene glycol) methacrylate) are prepared via subsequent visible light radical photopolymerization and iniferter processes. Thus, poly(styrene‐co‐4‐chloromethylstyrene) P(S‐co‐VBC) is synthesized by light induced free‐radical polymerization. Then, chloride moieties are substituted with triphenylmethyl (trityl) groups to give trityl‐substituted PS (PS‐trityl) under visible light irradiation using dimanganese decacarbonyl (Mn₂(CO)₁₀) photochemistry. Side chains are then grafted from PS‐trityl backbone via iniferter process to give desired graft copolymers in a controlled manner. The precursor intermediates and the final graft copolymers are analyzed by ¹H NMR, FT‐IR, and GPC measurements. © 2019 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2019, 57, 1344–1348     

A Grafting Study on Partially Dehydrochlorinated Poly(vinyl chloride) by Atom Transfer Radical Polymerization

HCl elimination in low ratio was first carried out from poly(vinyl chloride) to increase allylic chlorines. Partially dehydrochlorinated poly(vinyl chloride), having a macroinitiator effect, was grafted with tert‐butyl methacrylate via atom transfer radical polymerization in the presence of CuBr/2,2′‐bipyridine at 64°C in tetrahydrofuran. Original poly(vinyl chloride) was also grafted with tert‐butyl methacrylate under the same conditions to compare with that of partially dehydrochlorinated poly(vinyl chloride). The graft copolymers were characterized by elemental analysis, FTIR, ¹H and ¹³C‐NMR, differential scanning calorimetry, and gel permeation chromatography (GPC). Thermal stabilities of the graft copolymers were investigated by thermogravimetric analysis as compared with those of the macroinitiators.     

Synthesis of poly(β‐pinene)‐g‐poly(meth)acrylate by the combination of living cationic polymerization and atom transfer radical polymerization

New graft copolymers of β‐pinene with methyl methacrylate (MMA) or butyl acrylate (BA) were synthesized by the combination of living cationic polymerization and atom transfer radical polymerization (ATRP). β‐Pinene polymers with predetermined molecular weights and narrow molecular weight distributions (MWDs) were prepared by living cationic polymerization with the 1‐phenylethyl chloride/TiCl₄/Ti(OiPr)₄/nBu₄NCl initiating system, and the resultant polymers were brominated quantitatively by N‐bromosuccinamide in the presence of azobisisobutyronitrile, yielding poly(β‐pinene) macroinitiators with different bromine contents (Br/β‐pinene unit molar ratio = 1.0 and 0.5 for macroinitiators a and b , respectively). The macroinitiators, in conjunction with CuBr and 2,2′‐bipyridine, were used to initiate ATRP of BA or MMA. With macroinitiator a or b , the bulk polymerization of BA induced a linear first‐order kinetic plot and gave graft copolymers with controlled molecular weights and MWDs; this indicated the living nature of these polymerizations. The bulk polymerization of MMA initiated with macroinitiator a was completed instantaneously and induced insoluble gel products. However, the controlled polymerization of MMA was achieved with macroinitiator b in toluene and resulted in the desired graft copolymers with controlled molecular weights and MWDs. The structures of the obtained graft copolymers of β‐pinene with (methyl)methacrylate were confirmed by ¹H NMR spectra. © 2003 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 41: 1237–1242, 2003     

Aqueous MADIX/RAFT polymerization of diallyldimethylammonium chloride: Extension to the synthesis of poly(DADMAC)‐based double hydrophilic block copolymers

Macromolecular design by interchange of xanthates/reversible addition fragmentation chain transfer polymerization (MADIX/RAFT) of diallyldimethylammonium chloride (DADMAC) using the hydrophobic O‐ethyl‐S‐(1‐methoxycarbonyl) ethyl dithiocarbonate MADIX/RAFT mediating agent, Rhodixan A1, was investigated. Attempts to obtain an efficient control of DADMAC polymerization in a water/ethanol mixture failed because of significant chain transfer to ethanol. The use of a water‐soluble Rhodixan A1‐terminated acrylamide oligomer as the MADIX/RAFT agent enabled the controlled polymerization of DADMAC in water at 50 °C using the cationic azo initiator V‐50. An excellent agreement was found between experimental and theoretical M_n values throughout polymerization and over a broad range of initial concentration of xanthate. Polydispersity indexes (PDIs) at the end of the polymerization were abnormally high for a process showing a linear increase of M_n with monomer conversion (1.8 < PDI < 2.0). This feature was explained by the measurement of a high transfer constant to xanthate (C_x = 18.8 ± 1.6) but a low interchange transfer constant (C_ex = 1.5). Nevertheless, poly(acrylamide)–poly(DADMAC) double hydrophilic block copolymers (DHBCs) of controlled M_n and composition could be successfully synthesized for the first time. © 2010 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2010     

Modification of multiwall carbon nanotubes by grafting from controlled polymerization of styrene: Effect of the characteristics of the nanotubes

Linear polystyrene chains were grown from the convex surface of two commercially available multiwall carbon nanotubes (MWCNTs) with similar diameter but different lengths. The MWCNTs were supplied from Bayer Material Science® (purity >95%, external diameter = 13–16 nm, length = 1–10 μm, denoted MWCNT_BMS⁹⁵) and FutureCarbon GmbH (purity >99%, external diameter = 15 nm, length = 5–50 μm, denoted MWCNT_FC⁹⁹). The MWCNTs were oxidized with nitric acid, consecutively reacted with thionyl chloride, glycol or poly(ethylene glycol), 2‐bromo‐2‐methylpropionyl bromide and finally with styrene under atom transfer radical polymerization (ATRP) conditions. The content of polystyrene grafted from the surface of the MWCNTs can be controlled by adjusting the molecular weight of the poly(ethylene glycol), the initiator concentration and the monomer to carbon nanotube weight ratio. Under comparable experimental conditions, a higher amount of polystyrene is grafted from the MWCNT_BMS⁹⁵ than from MWCNT_FC⁹⁹. The difference in dimensions and the state of aggregation of the carbon nanotubes influence the grafting from polymerization reactions, where relative shorter and tightly aggregated carbon nanotubes promote higher polymerizations yields than longer and less aggregated carbon nanotubes. The increase of the viscosity of the carbon nanotube dispersion decreases the polymer grafting content. © 2010 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 48: 1035–1046, 2010     

Facile and versatile synthesis of rod‐coil poly(3‐hexylthiophene)‐based block copolymers by nitroxide‐mediated radical polymerization

A well‐defined and monofunctional poly(3‐hexylthiophene)‐based (P3HT) macroinitiator has been obtained through a clean, simple, and an efficient multistep synthesis process. The macroinitiator is obtained via intermolecular radical 1,2‐addition onto an ω‐acrylate‐terminated P3HT macromonomer. In a second step, well‐defined rod‐coil block copolymers were obtained by nitroxide‐mediated radical polymerization (NMRP) using the so‐called Blocbuilder^®. The polymerization was found to be controlled with various monomers such as styrene, isoprene, 4‐vinylpyridine, or methyl acrylate. This process constitutes a very promising way to obtain versatile and clean materials for organic electronics. © 2012 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2012     

The preparation and characterization of carboxylic acid‐coated silica nanoparticles

The preparation of carboxylic acid‐coated silica nanoparticles was investigated. A monolayer of carboxylic acid residues with controllable graft density was anchored to the nanoparticle by a ring‐opening reaction with succinic anhydride. Poly(methacrylic acid) [poly(MAA)] grafted nanoparticles were prepared via a polymerization–deprotection strategy. Tert‐butyl methacrylate was polymerized from the surface of silica nanoparticles in a predictable manner and with excellent control over the molecular weight distribution. Subsequent removal of the tert‐butyl group resulted in poly (MAA) grafted nanoparticles. The polymer nanoparticles were also functionalized with dyes, which may be useful in tracking the particles in biological systems. © 2012 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2012     

Preparation of polymer‐grafted carbon black nanoparticles by surface‐initiated atom transfer radical polymerization

Pristine carbon black was oxidized with nitric acid to produce carboxyl group, and then the carboxyl group was consecutively treated with thionyl chloride and glycol to introduce hydroxyl group. The hydroxyl group on the carbon black surface was reacted with 2‐bromo‐2‐methylpropionyl bromide to anchor atom transfer radical polymerization (ATRP) initiator. The ATRP initiator on carbon black surface was verified by TGA, FTIR, EDS, and elemental analysis. Then, poly (methyl methacrylate) and polystyrene chains were respectively, grown from carbon black surface by surface‐initiated atom transfer radical polymerization (SI‐ATRP) using CuCl/2,2‐dipyridyl (bpy) as the catalyst/ligand combination at 110 °C in anisole. ¹H NMR, TGA, TEM, AFM, DSC, and DLS were used to systemically characterize the polymer‐grafted carbon black nanoparticles. Dispersion experiments showed that the grafted carbon black nanoparticles had good solubilities in organic solvents such as THF, chloroform, dichloromethane, DMF, etc. © 2007 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 45: 3451–3459, 2007     

Synthesis of core‐shell poly(divinylbenzene) microspheres via reversible addition fragmentation chain transfer graft polymerization of styrene

Styrene has been grafted from crosslinked poly(divinylbenzene) core microspheres by both reversible addition fragmentation chain transfer (RAFT) polymerization and conventional free radical polymerization. The core microspheres were prepared by precipitation polymerization. Crosslinked poly(DVB) core microspheres containing double bonds on the particle surface can be used directly to graft polymers from the surface by RAFT without prior modification of the core microspheres. The RAFT agent 1‐phenylethyl dithiobenzoate (PEDB) was used: Particle sizes increased from 2 μm up to 3.06 μm, and the particle weight increased by up to 6.5%. PEDB controls the particle weight gain, the particle volume, and the molecular weight of the soluble polymer. PEDB was also used to synthesize core poly(DVB) RAFT microspheres that contain residual RAFT end groups on the surface and within the particle. Styrene was subsequently grafted from the surface of these core poly(DVB) RAFT microspheres. The generated microspheres were characterized by ¹H‐NMR spectroscopy, focused ion beam (FIB) milling, Coulter particle sizing, and size exclusion chromatography. © 2004 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 42: 5067–5076, 2004     

Radical grafting from glass fiber surface: Graft polymerization of vinyl monomers initiated by azo groups introduced onto the surface

This paper describes the radical graft polymerization of vinyl monomers from glass fiber surface initiated by alkylazo groups introduced onto the fiber surface. The introduction of azo groups onto the glass fiber surface was achieved by reaction of isocyanate groups which were previously attached onto the surface with two kinds of azo initiators, 4,4′-azobis(4-cyanopentanoic acid) (ACPA) and 2,2′-azobis(2-cyanopropanol) (ACP). The amounts of surface azo groups introduced by ACPA and ACP were both determined to be 1.3 × 10⁻⁵ mol g⁻¹ by nitrogen analysis. The radical graft polymerization of methyl methacrylate (MMA) was found to be initiated in the presence of the glass fiber having surface azo groups. During the polymerization, part of resultant poly(MMA) grafted onto the fiber surface through propagation of the polymer from the surface radicals produced by the decomposition of the azo groups. The percentage of grafting of poly(MMA) reached 48.1% after 24 h. The graft polymerizations of other monomers, such as styrene, N-vinylcarbazole, and acrylic acid, were also initiated by the surface azo groups, and the corresponding polymer effectively grafted onto the surface. © 1999 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 37: 2121–2128, 1999     

Precision synthesis of graft copolymers via living cationic polymerization of p‐acetoxystyrene followed by friedel–crafts‐type termination reaction

This study describes a novel precision synthesis strategy for graft copolymers using Friedel–Crafts‐type termination reaction between a cationically prepared poly(styrene derivative) and the naphthyl side groups from a poly(vinyl ether) main chain. The pendant alkoxynaphthyl groups on the poly(vinyl ether) efficiently terminated the living cationic polymerization of p‐acetoxystyrene (AcOSt) with SnCl₄ in the presence of ethyl acetate as an added base. This research provides the first example of a well‐defined graft copolymer prepared using this method. The resulting polymer contained 40 poly‐(AcOSt) branches, as calculated from the M_w determined via gel permeation chromatography–MALS analysis, which was in good agreement with the estimated number of branches obtained from ¹H NMR analysis. The acetoxy groups in the grafted poly(AcOSt) chains were easily converted into phenolic hydroxy groups under basic conditions. The as‐obtained graft copolymer with poly(p‐hydroxystyrene) side chains exhibited a pH‐sensitive phase separation in water. The synthetic method for preparing the graft copolymers was also effective in the living cationic polymerizations of other styrene derivatives. © 2013 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2013 , 51, 4675–4683     

Thermoresponsive NIPAM block copolymers containing densely grafted poly(vinyl ether) brushes synthesized by a combination of living cationic polymerization and RAFT polymerization

Diblock copolymers consisting of a multibranched polymethacrylate segment with densely grafted poly[2‐(2‐methoxyethoxy)ethyl vinyl ether] pendants and a poly(N‐isopropylacrylamide) segment were synthesized by a combination of living cationic polymerization and RAFT polymerization. A macromonomer having both a poly[2‐(2‐methoxyethoxy)ethyl vinyl ether] backbone and a terminal methacryloyl group was synthesized by living cationic polymerization. The sequential RAFT copolymerizations of the macromonomer and N‐isopropylacrylamide in this order were performed in aqueous media employing 4‐cyanopentanoic acid dithiobenzoate as a chain transfer agent and 4,4′‐azobis(4‐cyanopentanoic acid) as an initiator. The obtained diblock copolymers possessed relatively narrow molecular weight distributions and controlled molecular weights. The thermoresponsive properties of these polymers were investigated. Upon heating, the aqueous solutions of the diblock copolymers exhibited two‐stage thermoresponsive properties denoted by the appearance of two cloud points, indicating that the densely grafted poly[2‐(2‐methoxyethoxy)ethyl vinyl ether] pendants and the poly(N‐isopropylacrylamide) segments independently responded to temperature. © 2012 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2013     

Densely grafted polyisocyanides synthesized by two types of polymerization techniques

A series of novel polyisocyanide‐graft‐polystyrenes and polyisocyanide‐graft‐[polystyrene‐block‐poly(butyl acrylate)]s were synthesized through the grafting‐through and grafting‐from routes with two types of living polymerization techniques: polymerization with the Pd–Pt μ‐ethynediyl dinuclear complex as the initiator and catalyst for the polyisocyanide backbone and atom transfer radical polymerization for the grafted side chain. Through the introduction of a chiral center at the side chain of the polyisocyanide backbone, helical grafted and graft block polyisocyanides were prepared through the grafting‐from method. All of the obtained polymers exhibited polydispersities in the range of 1.07–1.41. This might have been the first time grafted polyisocyanides were prepared, especially helical grafted polyisocyanides, through the operation of two living polymerization techniques. © 2003 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 41: 1871–1880, 2003     

Functionalization of three‐dimensionally ordered macroporous cross‐linked polystyrene by atom‐transfer radical polymerization of hydroxyethyl methacrylate and subsequent derivatization

The surface‐initiated atom‐transfer radical polymerization (ATRP) technique was applied to the graft polymerization of 2‐hydroxyethyl methacrylate (HEMA) from three‐dimensionally ordered macroporous crosslinked polystyrene (3DOM CLPS) on which the initiator (benzyl chloride) was immobilized onto the pore wall of 3DOM CLPS by chloromethylation of benzene ring. By the adjustment of the monomer concentration or graft polymerization time, the thickness of grafted polymer layers can be controlled. FTIR analysis confirms that the graft polymerization of HEMA via ATRP had been taken place at the pore wall of 3DOM CLPS. SEM images of PHEMA‐grafted 3DOM CLPS show that the ordered structure is well preserved after graft polymerization and the grafted layers are dense and homogeneous. The maximum thickness of grafted layer is up to 35 nm and the corresponding percent weight increase is 102.8% in this study. Moreover, the PHEMA layers were further functionalized in high yield via their reactive hydroxyl groups under gentle condition. © 2008 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 46: 7950–7959, 2008     

High density cationic polymer brushes from combined “click chemistry” and RAFT‐mediated polymerization

A simple method for preparing cationic poly[(ar‐vinylbenzyl)trimethylammonium chloride)] [poly(VBTAC)] brushes was used by combined technology of “click chemistry” and reversible addition‐fragmentation chain transfer (RAFT) polymerization. Initially, silicon surfaces were modified with RAFT chain transfer agent by using a click reaction involving an azide‐modified silicon wafer and alkyne‐terminated 4‐cyanopentanoic acid dithiobenzoate (CPAD). A series of poly(VBTAC) brushes on silicon surface with different molecular weights, thicknesses, and grafting densities were then synthesized by RAFT‐mediated polymerization from the surface immobilized CPAD. The immobilization of CPAD on the silicon wafer and the subsequent polymer formation were characterized by X‐ray photoelectron spectroscopy, water contact angle measurements, grazing angle‐Fourier transform infrared spectroscopy, atomic force microscopy, and ellipsometry analysis. The addition of free CPAD was required for the formation of well‐defined polymer brushes, which subsequently resulted in the presence of free polymer chains in solution. The free polymer chains were isolated and used to estimate the molecular weights and polydispersity index of chains attached to the surface. In addition, by varying the polymerization time, we were able to obtain poly(VBTAC) brushes with grafting density up to 0.78 chains/nm² with homogeneous distributions of apparent needle‐like structures. © 2012 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2012     

AGET ATRP of water‐soluble PEGMA: Fast living radical polymerization mediated by iron catalyst

In this work, living radical polymerizations of a water‐soluble monomer poly(ethylene glycol) monomethyl ether methacylate (PEGMA) in bulk with low‐toxic iron catalyst system, including iron chloride hexahydrate and triphenylphosphine, were carried out successfully. Effect of reaction temperature and catalyst concentration on the polymerization of PEGMA was investigated. The polymerization kinetics showed the features of “living”/controlled radical polymerization. For example, M_n,GPC values of the resultant polymers increased linearly with monomer conversion. A faster polymerization of PEGMA could be obtained in the presence of a reducing agent Fe(0) wire or ascorbic acid. In the case of Fe(0) wire as the reducing agent, a monomer conversion of 80% was obtained in 80 min of reaction time at 90 °C, yielding a water‐soluble poly(PEGMA) with M_n = 65,500 g mol^?1 and M_w/M_n = 1.39. The features of “living”/controlled radical polymerization of PEGMA were verified by analysis of chain‐end and chain‐extension experiments. © 2012 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2012     

Atom‐transfer radical grafting polymerization of 2‐methacryloyloxyethyl phosphorylcholine from silicon wafer surfaces

2‐Methacryloyloxyethyl phosphorylcholine (MPC), a biomimetic monomer, was grafted from silicon wafer surfaces at room temperature by combining self‐assembly of initiator and surface‐initiated atom transfer radical polymerization. Two methods were used to control the grafting process. One was to add free initiator to the reaction system; the other was to add excess deactivator. The grafting densities up to 0.3 chains/nm² were obtained. The surface thickness increased linearly with MPC conversion. The thickness depended on catalyst and monomer concentrations, as well as activator/deactivator ratio. Poly(MPC) layers of >100 nm thick were obtained by optimizing the polymerization conditions. A second block of either poly(MPC) or poly[2‐(dimethylamino)ethyl methacrylate] was also grown from the grafted poly(MPC), demonstrating the system livingness. X‐ray photoelectron spectroscopy was used to examine the surface chemical compositions showed good agreement with the theoretical values. © 2004 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 42: 2931–2942, 2004     

Synthesis of graft copolymer by ATRP of MMA from poly(phenylacetylene)

The present report describes the synthesis of a densely grafted copolymer consisting of a rigid main chain and flexible side chains by the atom transfer radical polymerization (ATRP) of methyl methacrylate (MMA) from an ATRP initiator‐bearing poly(phenylacetylene) [poly(BrPA)]. Poly(BrPA) was obtained by the polymerization of 4‐ethynylbenzyl‐2‐bromoisobutyrate using [Rh(NBD)Cl]₂ in the presence of Et₃N. The ¹H NMR spectrum showed that poly(BrPA) was in the cis‐transoid form. Upon heating at 30 °C for 24 h the cis‐transoid form was maintained. ATRP of MMA from the poly(BrPA) was carried out at 30 °C using CuX (X = Br, Cl) as the catalyst and N,N,N′,N′,N′‐pentamethyldiethylenetriamine as the ligand, and the resulting graft copolymers were investigated with ¹H NMR and SEC. To analyze the graft structure in more detail, the graft copolymers were hydrolyzed with KOH and the resultant poly(MMA) part was investigated with ¹H NMR and SEC. The polydispersity indexes of 1.25–1.45 indicated that the graft copolymers have well‐controlled side chains. © 2006 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 44: 6697–6707, 2006