Sulfonated silica‐based electrolyte nanocomposite membranes

New functionalized particles were prepared by attaching sulfonated aromatic bishydroxy compounds onto fumed silica surface. First, a bromophenyl group was introduced onto the silica surface by reaction of bromophenyltrimethoxysilane with fumed silica. Then, sulfonated bishydroxy aromatic compounds were chemically attached to the silica surface by nucleophilic substitution reactions. The structure of the modified silica was characterized by elemental analysis: ¹³C‐NMR, ²⁹Si‐NMR, and FTIR. Afterward, novel inorganic–organic electrolyte composite membranes based on sulfonated poly(ether ether ketone) have been developed using the sulfonated aromatic bishydroxy compounds chemically attached onto the fumed silica surface. The composite membrane prepared using silica with sulfonated hydroxytelechelic, containing 1,3,4‐oxadiazole units, has higher proton conductivity values in all range of temperatures (40–140 °C) than the membrane containing only the plain electrolyte polymer, while the methanol permeability determined by pervaporation experiment was unchanged. A proton conductivity up to 59 mS cm^?1 at 140 °C was obtained. The combination of these effects may lead to significant improvement in fuel cells (fed with hydrogen or methanol) at temperatures above 100 °C. © 2006 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 44: 2278–2298, 2006     

Polysulfone ionomers functionalized with benzoyl(difluoromethylenephosphonic acid) side chains for proton‐conducting fuel‐cell membranes

Polysulfones carrying benzoyl(difluoromethylenephosphonic acid) side chains were prepared and investigated for use as proton‐conducting fuel‐cell membranes. In the first step, polysulfones were lithiated and reacted with methyl iodobenzoates to prepare p‐ and o‐iodobenzoyl polysulfones. Next, the phosphonated polysulfones were prepared via CuBr‐mediated cross‐coupling reactions between the iodinated polymer and [(diethoxyphosphinyl)difluoromethyl]zinc bromide. Finally, dealkylation with bromotrimethylsilane afforded highly acidic ? CF₂? PO₃H₂ derivatives. The replacement of the iodine atoms by ? CF₂? PO₃Et₂ units was almost quantitative in the case of o‐iodobenzoyl polysulfone. Membranes based on ionomers having 0.90 mmol of phosphonic acid units/g of dry polymer took up 6 wt % water when immersed at room temperature, and conductivities up to 5 mS cm^?1 at 100 °C were recorded. This level of conductivity was comparable to that reached by a membrane based on a sulfonated polysulfone having 0.86 mmol of sulfonic acid/g of dry polymer. Thermogravimetry revealed that the aryl? CF₂? PO₃H₂ arrangement decomposed at approximately 230 °C via cleavage of the C? P bond. © 2006 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 45: 269–283, 2007.     

The impact of alkyl tri‐methyl ammonium side chains on perfluorinated ionic membranes for electrochemical applications

Three different perfluorinated type polymers as anion exchange membranes for electrochemical applications were studied. They have a sulfonamide linkage to a spacer methylene chain attached to a tri‐methyl ammonium cation, specifically using a three carbon spacer chain (PFAEM_H_C3), and methylated imide polymers with three (PFAEM_CH3_C3) and six carbon spacer chain (PFAEM_CH3_C6). There are significant number of zwitterionic side chains in the PFAEM_H_C3 polymer and very few in the PFAEM_CH3_C3 or the PFAEM_CH3_C6 polymer. They have similar halide conductivity, but the PFAEM_CH3_C6 showed highest OH^? conductivity, 122 mS cm^?1 at 80 °C and 95% RH. The larger spacer chain polymer, PFAEM_CH3_C6 has a higher water uptake value (λ = 9) compared to PFAEM_CH3_C3(λ = 7) at 60 °C and 95% RH in the Cl^? form. Therefore, it has a larger domain spacing of 4.9 nm versus 4.1 nm from small angle X‐ray scattering data. The polymer was characterized by FTIR and DFT was used to fully assign the spectra. © 2019 Wiley Periodicals, Inc. J. Polym. Sci., Part B: Polym. Phys. 2019 , 57, 700–712     

Synthesis and properties of new fluorinated polymers bearing pendant imidazole groups for fuel cell membranes operating over a broad relative humidity range

New alternating copolymers comprising a chlorotrifluorinated backbone and imidazole‐terminated pendant ethylene oxide groups have been prepared with a view to their use as a component of proton‐conducting membranes in polymer electrolyte fuel cells. A vinyl ether containing an imidazole (Imi) function protected by a benzyl group (BVI) was first synthesized in a three‐step reaction. It was then copolymerized in solution with chlorotrifluoroethylene (CTFE) by conventional radical copolymerization leading to alternating poly(BVI‐alt‐CTFE) copolymers in good yields. Deprotection of the benzyl group under hydrogen produced a chlorotrifluorinated poly(Imi‐alt‐CTFE) copolymer. The polymer was subsequently used to form blend membranes with sulfonated poly(ether ether ketone) (sPEEK). The conductivity of blend membranes of poly (Imi‐alt‐CTFE) with sPEEK lies in the range of 4–10 mS cm^?1 at 40–70 °C and, for blend membranes rich in poly(Imi‐alt‐CTFE), is little dependent on relative humidity between 30 and 100%. It is surmised that the polymer and membrane composition favor microstructural phase separation into chlorotrifluorinated polymer backbone domains and regions in which imidazole groups are clustered. © 2009 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 48: 223–231, 2010     

Sulfonated polybenzimidazoles: Proton conduction and acid–base crosslinking

A series of soluble, benzimidazole‐based polymers containing sulfonic acid groups (SuPBI) has been synthesized. SuPBI membranes resist extensive swelling in water but are poor proton conductors. When blended with high ion exchange capacity (IEC) sulfonated poly(ether ether ketone) (SPEEK), a polymer that has high proton conductivity but poor mechanical integrity, ionic crosslinks form reducing the extent of swelling. The effect of sulfonation of PBI on crosslinking in these blends was gauged through comparison with nonsulfonated analogs. Sulfonic acid groups present in SuPBI compensate for acid groups involved in crosslinking, thereby increasing IEC and proton conductivity of the membrane. When water uptake and proton conductivity were compared to the IEC of blends containing either sulfonated or nonsulfonated PBI, no noticeable distinction between PBI types could be made. Comparisons were also made between these blends and pure SPEEK membranes of similar IEC. Blend membranes exhibit slightly lower maximum proton conductivity than pure SPEEK membranes (60 vs. 75 mS cm^?1) but had significantly enhanced dimensional stability upon immersion in water, especially at elevated temperature (80 °C). Elevated temperature measurements in humid environments show increased proton conductivity of the SuPBI membranes when compared with SPEEK‐only membranes of similar IEC (c.f. 55 for the blend vs. 42 mS cm^?1 for SPEEK at 80 °C, 90% relative humidity). © 2010 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 48: 3640–3650, 2010     

A novel polymer gel electrolyte: Direct polymerization of ionic liquid from surface of silica nanoparticles

A novel polymer electrolyte is synthesized by directly grafting poly ionic liquids onto silica nanoparticles. The kinetic study of this surface‐initiated polymerization has also been included. A gel‐state electrolyte is formed by mixing this type of polymer/silica nanocomposite with ionic liquids under 60 °C, which exhibits an excellent conductivity of 0.8 mS/cm at room temperature and 14.7 mS/cm at 90 °C. In addition, the mechanism of gel formation has also been discussed in this article. © 2013 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2014 , 52, 121–127     

Cross‐linked poly(aryl ether sulfone) membranes for direct methanol fuel cell applications

Partially sulfonated poly(aryl ether sulfone) (PESS) was synthesized and methacrylated via reaction with glycidyl methacrylate (PESSGMA) and cross‐linked via radical polymerization with styrene and vinyl‐phosphonic acid (VPA). The chemical structures of the synthesized pre‐polymers were characterized via FTIR and ¹H NMR spectroscopic methods and molecular weight was determined via GPC. Membranes of these polymers were prepared via solution casting method. The crosslinking of the PESS polymer reduced IEC, proton conductivity, swelling in water, and methanol permeability of the membranes while increasing the modulus and the glass transition temperature. However, the introduction of the VPA comonomer increased the proton conductivity while maintaining excellent resistance to methanol cross‐over, which was significantly higher as compared with both PESS and the commercial Nafion membranes. Membranes of PESSGMA copolymers incorporating VPA, exhibited proton conductivity values at 60 °C in the range of 16–32 mS cm⁻¹ and methanol permeability values in the range of 6.52 × 10⁻⁹ – 1.92 × 10⁻⁸ cm² s⁻¹. © 2018 Wiley Periodicals, Inc. J. Polym. Sci., Part B: Polym. Phys. 2018 , 56, 558–575     

Poly(tetrafluorostyrenephosphonic acid)–polysulfone block copolymers and membranes

A series of ionic ABA triblock copolymers having a central polysulfone (PSU) block and poly(2,3,5,6,‐tetrafluorostyrene‐4‐phosphonic acid) (PTFSPA) outer blocks with different lengths were prepared and studied as electrolyte membranes. PSU with terminal benzyl bromide was used as a bifunctional macroinitiator for the formation of poly(2,3,4,5,6‐pentafluorostyrene) (PPFS) blocks by atom transfer radical polymerization. Selective and complete phosphonation of the PPFS blocks was achieved via a Michaelis?Arbuzov reaction using tris(trimethylsilyl)phosphite at 170 °C. Copolymer films were cast from solution and subsequently fully hydrolyzed to produce transparent flexible proton conducting PTFSPA‐b‐PSU‐b‐PTFSPA membranes with a thermal stability reaching above 270 °C under air, and increasing with the PTFSPA content. Studies of thin copolymer electrolyte membranes by tapping mode atomic force microscopy showed phase separated morphologies with continuous proton conducting PTFSPA nano scale domains. Block copolymer membranes reached a proton conductivity of 0.08 S cm^?1 at 120 °C under fully hydrated conditions, and 0.8 mS cm^?1 under 50% relative humidity at 80 °C. © 2013 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2013 , 51, 4657–4666     

Synthesis of highly sulfonated polybenzimidazoles by direct copolymerization and grafting

A series of highly sulfonated, ether‐containing polybenzimidazoles (SOPBI) with controlled sulfonation degrees were synthesized from various stoichiometric ratio mixtures of sodium 6,6'‐oxybis(3‐carboxybenzenesulfonate) (SODBA), 4,4'‐oxydibenzoic acid (ODBA), and 3,3'‐diaminobenzidine (DAB) by solution copolycondensation in poly(phosphoric acid). The resulting sulfonated polymers were further sulfonated by grafting of pendant sulfonic acid chains via a reaction of 1,3‐propane sultone with lithiated‐N of the imidazole rings in the polymer backbone, yielding materials with high, absolute IEC values (3.42–4.15 meq g^?1). Due to self‐neutralization, the solid state polymers possessed “free” acid content of 1.40 to 2.15 meq g^?1, were soluble in organic solvents yet insoluble in aqueous solution, while displaying proton conductivites (11–47 mS cm^?1) at elevated temperatures (80 °C, 95% RH). © 2013 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2013, 51, 3654–3666     

Highly proton conducting proton‐exchange membranes based on fluorinated poly(arylene ether ketone)s with octasulfonated segments

A new bisphenol monomer containing a pair of electron‐rich tetra‐arylmethane units was designed and synthesized. Based on this monomer, along with commercial 4,4′‐(hexafluoroisopropylidene)diphenol A and 4,4′‐difluorobenzophenone, a series of novel poly(arylene ether ketone)s containing octasulfonated segments of varying molar percentage (x) (6F‐SPAEK‐x) were successfully synthesized by polycondensation reactions, followed by sulfonation. Tough, flexible, and transparent membranes, exhibiting excellent thermal stabilities and mechanical properties were obtained by casting. 6F‐SPAEK‐x samples exhibited appropriate water uptake and swelling ratios at moderate ion exchange capacities (IECs) and excellent proton conductivities. The highest proton conductivity (215 mS cm⁻¹) is observed for hydrated 6F‐SPAEK‐15 (IEC = 1.68 meq g⁻¹) at 100 °C, which is more than 1.5 times that of Nafion 117. Furthermore, the 6F‐SPAEK‐10 membrane exhibited comparable proton conductivity (102 mS cm⁻¹) to that of Nafion 117 at 80 °C, with a relatively low IEC value (1.26 meq g⁻¹). Even under 30% relative humidity, the 6F‐SPAEK‐20 membrane (2.06 meq g⁻¹) showed adequate conductivity (2.1 mS cm⁻¹) compared with Nafion 117 (3.4 mS cm⁻¹). The excellent comprehensive properties of these membranes are attributed to well‐defined nanophase‐separated structures promoted by strong polarity differences between highly ionized and fluorinated hydrophobic segments. © 2017 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2018 , 56, 25–37     

Synthesis of guanidinium‐based anion exchange membranes and their stability assessment

Alkaline fuel cells potentially offer improved conversion efficiency and the prospect of using non‐noble metal catalysts; however, low conductivity and fast degradation of anion exchange membranes (AEMs) prevent their widespread application. In this work, a series of novel composite AEMs were synthesized by incorporating guanidinium‐based polymers into a porous polytetrafluoroethylene (PTFE) film. The guanidinium‐based polymers were polymerized using a condensation process between a guanidinium salt and two different diamines so that the guanidinium cations were tethered to the polymer backbone to enhance both conductivity and durability. In addition, polymer crosslinking was conducted to further reinforce the mechanical strength of the membranes and interlock the guanidinium moieties to the porous PTFE. It was found that the ionic conductivity of the synthesized membrane reached up to approximately 80 mS cm^?1 at 20°C in deionized water. These membranes also exhibited superior stability compared to commercial quaternary ammonium AEMs after being exposed in 5 M KOH solution at 55°C for 50 h. Copyright © 2013 John Wiley & Sons, Ltd.     

Grafting of polymers onto and/or from silica surface during the polymerization of vinyl monomers in the presence of γ‐ray‐irradiated silica

The effects of radicals on silica surface, which were formed by γ‐ray irradiation, on the polymerization of vinyl monomers were investigated. It was found that the polymerization of styrene was remarkably retarded in the presence of γ‐ray‐irradiated silica above 60 °C, at which thermal polymerization of styrene is readily initiated. During the polymerization, a part of polystyrene formed was grafted onto the silica surface but percentage of grafting was very small. On the other hand, no retardation of the polymerization of styrene was observed in the presence of γ‐ray‐irradiated silica below 50 °C; the polymerization tends to accelerate and polystyrene was grafted onto the silica surface. Poly(vinyl acetate) and poly(methyl methacrylate) (MMA) were also grafted onto the surface during the polymerization in the presence of γ‐ray‐irradiated silica. The grafting of polymers onto the silica surface was confirmed by thermal decomposition GC‐MS. It was considered that at lower temperature, the grafting based on the propagation of polystyrene from surface radical (“grafting from” mechanism) preferentially proceeded. On the contrary, at higher temperature, the coupling reaction of propagating polymer radicals with surface radicals (“grafting onto” mechanism) proceeded to give relatively higher molecular weight polymer‐grafted silica. © 2006 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 44: 2972–2979, 2006     

Sulfonic and Phosphonic Acid and Bifunctional Organic–Inorganic Hybrid Membranes and Their Proton Conduction Properties

Hybrid organic–inorganic approaches are used for the synthesis of bifunctional proton exchange membrane fuel cell (PEMFC) membranes owing to their ability to combine the properties of a functionalized inorganic network and an organic thermostable polymer. We report the synthesis of both sulfonic and phosphonic acid functionalized mesostructured silica networks into a poly(vinylidenefluoride‐co‐hexafluoropropylene) (poly(VDF‐co‐HFP) copolymer. These membranes, containing different amounts of phosphonic acid and sulfonic acid groups, have been characterized using FTIR and NMR spectroscopy, SA‐XRD, SAXS, and electrochemical techniques. The proton conductivity of the bifunctional hybrid membranes depends strongly on hydration, increasing by two orders of magnitude over the relative humidity (RH) range of 20 to 100 %, up to a maximum of 0.031 S cm⁻¹ at 60 °C and 100 % RH. This value is interesting as only half of the membrane conducts protons. This approach allows the synthesis of a porous SiO₂ network with two different functions, having  SO₃H and  PO₃H₂ embedded in a thermostable polymer matrix.     

Partially fluorinated and ammonium‐functionalized terpolymers: Effect of aliphatic groups on the properties of anion conductive membranes

Synthesis and properties of a series of ammonium‐containing terpolymers (QPAF‐3) as anion conductive membranes are reported. The QPAF‐3s composed of perfluoroalkylene, alkylene, and ammonium‐functionalized phenylene groups without heteroatom linkages in the main chain were synthesized via nickel‐mediated polycondensation reaction, followed by chloromethylation, quaternization, and ion exchange reactions. Self‐standing, bendable membranes were obtained by solution casting. The QPAF‐3 membrane with optimized terpolymer composition and ion exchange capacity (1.46 meq g^?1) showed high hydroxide ion conductivity (123 mS cm^?1 in water at 80 °C). The alkaline stability test in 1 M KOH for 1000 h at 80 °C and the post‐test analysis with IR spectra and tensile strength suggested that ammonium groups were likely to be decomposed while the polymer main chain was chemically more robust. The presence of the alkylene groups in the terpolymers lowered solubility, glass transition temperature, and elongation property of the resulting membranes. © 2016 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2017 , 55 , 1442–1450     

Effective grafting of polymers onto ultrafine silica surface: Photopolymerization of vinyl monomers initiated by the system consisting of trichloroacetyl groups on the surface and Mn2(CO)10

The effective grafting of vinyl polymers onto an ultrafine silica surface was successfully achieved by the photopolymerization of vinyl monomers initiated by the system consisting of trichloroacetyl groups on the surface with Mn₂(CO)₁₀ under UV irradiation at 25 °C. The introduction of trichloroacetyl groups onto the surface of silica was achieved by the reaction of trichloroacetyl isocyanate with surface amino groups, which were introduced by the treatment of silica with 3‐aminopropyltriethoxysilane. During the polymerization, the corresponding polymers were effectively grafted onto the surface, based on the propagation of polymer from surface radicals formed by the interaction of trichloroacetyl groups and Mn₂(CO)₁₀. The percentage of poly(methyl methacrylate) grafting onto the silica reached 714.6% after 90 min. The grafting efficiency (proportion of grafted polymer to total polymer formed) in the polymerization of methyl methacrylate was very high, about 80%, indicating the depression of formation of ungrafted polymer. Polymer‐grafted silica gave a stable colloidal dispersion in good solvents for grafted polymer. © 2001 John Wiley & Sons, Inc. J Polym Sci Part A: Polym Chem 39: 2157–2163, 2001     

Investigation of proton conductivity of anhydrous proton exchange membranes prepared via grafting vinyltriazole onto alkaline‐treated PVDF

This work uses a simple “grafting through” approach in the preparation of anhydrous poly(vinylidene fluoride) (PVDF)‐g‐PVTri polymer electrolyte membranes (PEMs). Alkaline‐treated PVDF was used as a macromolecule in conjunction with vinyltriazole in the graft copolymerization. The obtained polymer was subsequently doped with triflic acid (TA) at different stoichiometric ratios with respect to triazole units and the anhydrous PEMs (PVDF‐g‐PVTri‐(TA)_x) were prepared. All samples were characterized by FTIR and ¹H NMR. The composition of PVDF‐g‐PVTri was determined by energy dispersive spectroscopy. Thermal properties of the membranes were examined by thermogravimetric analysis and differential scanning calorimetry. The surface roughness and morphology of the membranes were studied using atomic force microscopy, X‐ray diffraction, and scanning electron microscopy. PVDF‐g‐PVTri‐(TA)₃ (C3‐TA₃) with a degree of grafting of 47.22% showed a maximum proton conductivity of 0.09 S cm^?1 at 150 °C and anhydrous conditions. © 2014 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2014 , 52, 1885–1897     

Phosphoric acid‐doped imidazolium ionomers with enhanced stability for anhydrous proton‐exchange membrane applications

Phosphoric acid‐doped crosslinked proton‐conducting membranes with high anhydrous proton conductivity, and good chemical stability in phosphoric acid were synthesized and characterized. The synthetic procedure of the acid‐doped composite membranes mainly involves the in situ crosslinking of polymerizable monomer oils (styrene and acrylonitrile) and vinylimidazole, and followed by the sulfonation of pendant imidazole groups with butanesultone, and further doped with phosphoric acid. The resultant phosphoric acid‐doped composite electrolyte membranes are flexible and show high thermal stability and high‐proton conductivity up to the order of 10^?2 S cm^?1 at 160 °C under anhydrous conditions. The phosphoric acid uptake, swelling degree, and proton conductivity of the composite membranes increase with the vinylimidazole content. The resultant composite membranes also show good oxidative stability in Fenton's reagent (at 70 °C), and quite good chemical stability in phosphoric acid (at 160 °C). The properties of the prepared electrolyte membranes indicate their promising prospects in anhydrous proton‐exchange membrane applications. © 2013 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys, 2013 , 51, 1311–1317     

Synthesis and properties of novel polyimides from sulfonated binaphthalene dianhydride for proton exchange membranes

A sulfonated dianhydride monomer, 6,6′‐disulfonic‐4,4′‐binaphthyl‐1,1′,8,8′‐tetracarboxylic dianhydride (SBTDA), was successfully synthesized by direct sulfonation of the parent dianhydride, 4,4′‐binaphthyl‐1,1′,8,8′‐tetracarboxylic dianhydride (BTDA), using fuming sulfuric acid as the sulfonating reagent. A series of sulfonated homopolyimides were prepared from SBTDA and various common nonsulfonated diamines. The resulting polymer electrolytes, which contain ion conductivity sites on the deactivated positions of the aryl backbone rings, displayed high proton conductivities of 0.25–0.31 S cm^?1 at 80 °C. The oxidative stability test indicated that the attachment of the ? SO₃H groups onto the dianhydride units did not deteriorate the oxidative stability of the SPI membranes. The better membranes were achieved by the copolymerization of nonsulfonated diamine, SBTDA, and BTDA. Copolymer membrane synthesized from hexane‐1,6‐diamine, SBTDA, and BTDA displayed excellent water stability of more than 1000 h at 90 °C, while its proton conductivity was still at a high level (comparable to that of Nafion 117). Furthermore, the novel block copolymer ( II‐b ) displayed higher proton conductivity compared with the random one ( II‐r ) obviously, probably due to the slightly higher water uptake and better microphase separated morphology. © 2008 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 46: 2820–2832, 2008     

Anion conductive aromatic polymers containing fluorenyl groups: Effect of the position and number of ammonium groups

Synthesis and properties of anion conductive aromatic block copolymers, QPE‐bl‐3, QPE‐bl‐3 M2, and M4, containing fluorenylidene biphenylene groups as scaffold for ammonium groups are described. These copolymers share the same main chain structure, but the position and the number of ammonium groups on a fluorenyl group differ. High molecular weight quaternized block copolymers were obtained via typical chloromethylation reaction or using preaminated monomers, and were well‐characterized by ¹H NMR spectra. Self‐standing bendable membranes were obtained by solution casting. QPE‐bl‐3 M4 membranes containing four ammonium groups per hydrophilic repeat unit (highest ammonium density) in the hydrophilic block exhibited well developed phase‐separated morphology, while QPE‐bl‐3 membranes containing two ammonium groups per hydrophilic repeat unit exhibited high anion conductivity. The highest anion conductivity (104 mS/cm) was obtained with QPE‐bl‐3 membrane (IEC = 2.1 meq/g) at 80 °C in water. An H₂/O₂ alkaline fuel cell was operable with the membrane to achieve 62 mW/cm² of the maximum power density at 161 mA/cm² of the current density. © 2015 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2016 , 54, 935–944     

Energy material - the role of silicotungstic acid and fly ash in sulfonated poly (ether sulfone) composites for PEMFC applications

The composite polymer electrolyte membranes were prepared from sulfonated poly (ether sulfone) (SPES), silicotungstic acid (STA) and fly ash (FA). Post sulfonation process was adopted to synthesize SPES using sulphuric and chlorosulfonic acid. The prepared electrolyte membranes were examined by water uptake capacity, swelling ratio, ion-exchange ability, proton conductivity, thermal stability and electrochemical performance for evaluating the pertinence of these membranes in fuel cell applications. As such the pristine membrane restricts with the proton conductivity of 0.042?S cm^?1 at 30?°C and 0.060?S cm^?1 at 90?°C while the polymer composite membrane, SP-STA-FA-10 reveals the maximum conductivity of 0.054?S cm^?1 at 30?°C and 0.073?S cm^?1 at 90?°C. It also exhibits good thermal stability than that of the pure membrane. The membrane electrode assemblies (MEAs) have been successfully developed from SPES as well as SP-STA-FA-10 membranes and their electrochemical performance were studied the wide range of current density. Herein, the composite membranes derived from SPES, STA and FA can be viable candidates for fuel cell applications.