Effect of scale and surface chemistry on the mechanical properties of carbon nanotubes‐based composites

In this article, Multi‐Walled Carbon Nanotubes (MWCNTs) of varying diameters, both untreated and polycarboxylated, were dispersed at constant weight percentage in an epoxy matrix, and resulting fracture toughnesses (K_Ic) were measured in each case. We show that changing the MWCNT diameter has two effects on the composite fracture toughness: (i) a small MWCNT diameter enables larger interfacial surface for adhesion maximization, which increases toughness; (ii) at the same time, it limits the available pull‐out energy and reduces the MWCNT ability to homogeneously disperse in the matrix due to this same large active surface: this decreases toughness. Most commercially available MWCNTs have a length range of several μm, thus an optimal diameter exists which depends on MWCNT wall thickness and surface treatment. Such optimal diameter maximizes pull‐out energy and thus composite fracture toughness. © 2012 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys, 2012     

Deformable strain sensors based on patterned MWCNTs/polydimethylsiloxane composites

Patterned MWCNT/polydimethylsiloxane (PDMS) nanocomposite strain sensors were achieved by a microelectromechanical system assisted electrophoretic deposition (EPD) technique. With the combined effect of superior intrinsic piezoresistivity of the individual MWCNT and the tunneling effect of the MWCNT network, the stretchable composite demonstrates high sensitivity to the tensile strain. The gauge factor shows a strong dependence on both the initial resistance of the CNT/PDMS composite and the applied strain level. The mechanism is elucidated by analyzing the structure‐property‐function of patterned CNT networks. When the entanglement of a MWCNT network allows effective load transfer, the sensitivity is primarily dominated by the intrinsic piezoresistivity of individual MWCNTs. Conversely, when the MWCNTs interpenetrate loosely, the tunneling effect prevails. The sensitivity of the device can be tailored by the proposed technique since MWCNT film thickness/density can be readily controlled by means of the patterning parameters of the EPD process. The work provides useful guidance for design and development of strain/stress sensors with targeted sensitivity for flexible electronics applications. © 2013 Wiley Periodicals, Inc. J. Polym. Sci., Part B: Polym. Phys. 2013 , 51, 1505–1512     

High strength toughened epoxy nanocomposite based on poly(ether sulfone)‐grafted multi‐walled carbon nanotube

Hydroxyl terminated poly(ether sulfone) (PES) has been grafted on multi‐walled carbon nanotube (MWCNT). The grafting reaction was confirmed by different characterization techniques such as Fourier transform infrared spectroscopy, Raman spectroscopy, thermogravimetric analysis, and transmission electron microscopy. The extent of the grafting was found to be around 58 wt%. Hybrid nanocomposite of epoxy with the modified MWCNT was also prepared. Effect of grafting on the mechanical, thermal, and viscoelastic properties was studied. Dynamic mechanical studies show an increase in the storage modulus for the nanocomposite prepared using PES‐grafted MWCNT compared with neat epoxy system. PES‐grafted MWCNT–epoxy nanocomposite induces a significant increase in both tensile strength (26%) and fracture toughness (125%) of the epoxy matrix. Field emission scanning electron micrographs of fractured surfaces were examined to understand the toughening mechanism. Copyright © 2015 John Wiley & Sons, Ltd.     

Nanoindentation,nanoscratch, and nanotensile testing of poly(vinylidene fluoride)‐polyhedral oligomeric silsesquioxane nanocomposites

Nanocomposites composed of a poly(vinylidene fluoride) (PVDF) matrix and 0, 3, 5, and 8 wt % fluoropropyl polyhedral oligomeric silsesquioxane (FP‐POSS) were prepared by using the solvent evaporation method. The morphology and the crystalline phase of the nanocomposites were investigated by digital microscopy, scanning probe microscopy, X‐ray diffractometer, and Fourier transform infrared spectroscopy. FP‐POSS acted as nucleating agent in PVDF matrix. A small content of FP‐POSS resulted in an incomplete nucleation of PVDF and generated bigger spherical particles, whereas higher contents led to a complete nucleation and formed more separate and less‐crosslinked particles. Nanoindentation, nanoscratch, and nanotensile tests were carried out to study the influence of different contents of FP‐POSS on the key static and dynamic mechanical properties of different systems. The nanocomposite with 3 wt % FP‐POSS was found to possess enhanced elastic properties and hardness. However, with the increase of the FP‐POSS content, the elastic modulus and hardness were found to decrease, and the improvement on stiffness was negative at contents of 5 and 8 wt %. Compared with neat PVDF, the scratch resistance of the PVDF/FP‐POSS nanocomposites was decreased due to a rougher surface derived from the bigger spherulites. Nanotensile testing results showed both the stiffness and toughness of PVDF‐FP_3% were enhanced and further additions of FP‐POSS brought dramatic enhancements in toughness while associated with a decline in stiffness. Dynamical mechanical properties indicated the viscosity of the nanocomposites increased with the increasing FP‐POSS contents. © 2012 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys, 2012     

Synthesis of PVDF/BiFeO3 nanocomposite and observation of enhanced electrical conductivity and low‐loss dielectric permittivity at percolation threshold

A novel two‐phase polymer nanocomposite film comprising of polyvinylidene fluoride (PVDF) and nanocrystalline (～90 nm) semiconducting multiferroic BiFeO₃ (BFO) have been fabricated by hot‐molding technique. Such flexible thick nanocomposite films, semicrystalline in nature, exhibited extraordinarily high effective dielectric permittivity ε_eff ～ 10³ (compared with that of pure PVDF) near the low percolation threshold (f_c = 0.12) at room temperature (RT) and the films also possessed low dielectric loss (～0.18). The polarization‐electric field (P‐E) hysteresis loops are displayed at RT, which indicate ferroelectric like behavior of PVDF still persists in the percolative nanocomposite. There is also large increase of remanent polarization of BFO in the composite indicating improvement of the multiferroic behavior of BFO embedded in the PVDF polymer. The sample also indicates good fatigue endurance. Formation of microcapacitors and percolative behavior are correlated to explain the obtained results based on the special geometry of the BFO nanofillers. © 2012 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys, 2012     

Toughening of poly(L‐lactide)/multiwalled carbon nanotubes nanocomposite with ethylene‐co‐vinyl acetate

Poly(L ‐lactide)/multiwalled carbon nanotubes (PLLA/MWCNTs) nanocomposite recently attracts much attention because of its excellent comprehensive properties including improved thermostability, tensile strength, and conductivity. However, the nanocomposite exhibits similar brittleness compared with unmodified PLLA. In this work, a polar elastomer, that is, ethylene‐co‐vinyl acetate (EVA), was introduced into PLLA/MWCNTs nanocomposite. The selective distribution of MWCNTs and the effects of EVA on crystalline structure of PLLA were investigated using scanning electron microscope, transmission electron microscope, differential scanning calorimetry, and wide angle X‐ray diffraction. The results show that the presence of EVA induces the change of the distribution of MWCNTs in the nanocomposites, and consequently, the cold crystallization of PLLA is prevented. With the increase of EVA content, both the ductility and the impact resistance of PLLA/FMWCNTs are improved greatly, indicating the toughening effect of EVA on PLLA/MWCNTs nanocomposite. The decreased tensile strength and modulus can be compensated through annealing treatment. © 2010 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys, 2011     

Surface modification of MWCNTs with glucose and their utilization for the production of environmentally friendly nanocomposites using biodegradable poly(amide‐imide) based on N‐trimellitylimido‐S‐valine matrix

In the present investigation, the preparation, characterization, and surface morphology of poly(amide‐imide) (PAI)/multi‐walled carbon nanotubes (MWCNTs) bionanocomposites (BNCs) were the main goals of the study. At first, an optically active PAI based on S‐valine as a biodegradable segment was synthesized. Then, carboxyl‐modified MWCNTs were functionalized with glucose (f‐MWCNT) as a biological active molecule in a green method to achieve a fine dispersion of f‐MWCNT bundles in the PAI matrix. The existence of S‐valine in the PAI matrix and functionalized MWCNT with glucose resulted in a series of potentially biodegradable nanocomposites. The obtained BNCs were characterized by various techniques. Field emission scanning and transmission electron microscopy micrographs of the composites showed a fine dispersion of f‐MWCNTs in the polymer matrix because of hydrogen bonding and π–π stacking interaction between f‐MWCNTs and polymer functional groups and aromatic moieties. Adding f‐MWCNTs into polymer matrix significantly improved the thermal stability of BNCs because of the increased interfacial interaction between the PAI matrix and f‐MWCNTs and also good dispersion of f‐MWCNT in the polymer matrix. Copyright © 2015 John Wiley & Sons, Ltd.     

Fabrication and electroactive responsive behavior of shape–memory nanocomposite incorporated with self‐assembled multiwalled carbon nanotube nanopaper

A novel shape–memory nanocomposite that exhibits electrical actuation capabilities was fabricated by incorporating a conductive multiwalled carbon nanotube (MWCNT) nanopaper into shape–memory polymer matrix. The self‐assembled MWCNT nanopaper was made on hydrophilic polycarbonate membrane. This process was based on well‐defined dispersion of the nanosized individual MWCNT and controlled traditional pressure vacuum deposition procedure. The self‐assembled MWCNTs in the nanopaper provided a percolating conductive network with a large interfacial area. It not only offered a high electrical conductivity but also simultaneously enhanced recovery speed by electrically resistive heating, with increasing the content of MWCNT nanopaper in nanocomposite. Copyright © 2011 John Wiley & Sons, Ltd.     

Polymer coating of carboxylic acid functionalized multiwalled carbon nanotubes via reversible addition‐fragmentation chain transfer mediated emulsion polymerization

In this work, successful polymer coating of COOH‐functionalized multiwalled carbon nanotubes (MWCNTs) via reversible addition fragmentation chain transfer (RAFT) mediated emulsion polymerization is reported. The method used amphiphilic macro‐RAFT copolymers as stabilizers for MWCNT dispersions, followed by their subsequent coating with poly(methyl methacrylate‐co‐butyl acrylate). Poly(allylamine hydrochloride) was initially used to change the charge on the surface of the MWCNTs to facilitate adsorption of negatively charged macro‐RAFT copolymer onto their surface via electrostatic interactions. After polymerization, the resultant latex was found to contain uniform polymer‐coated MWCNTs where polymer layer thickness could be controlled by the amount of monomer fed into the reaction. The polymer‐coated MWCNTs were demonstrated to be dispersible in both polar and nonpolar solvents. © 2012 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2013     

Grafting of polymer matrix to exfoliated montmorillonite nanoplatelets in nanocomposite film cast from soap‐free emulsion polymerized latex and its fortified mechanical properties

Poly(methyl acrylate‐co‐methyl methacrylate) [P(MA‐co‐MMA)] nanocomposite film containing 1 wt % of montmorillonite (MMT) exhibited unusual higher ductility, higher strain recovery ratio after creep, and higher modulus and strength compared to neat P(MA‐co‐MMA) as they were cast from their individual latices fabricated by soap‐free emulsion polymerization. The fortified mechanical properties were attributed to the MgO components of exfoliated MMT nanoplatelets being grafted by P(MA‐co‐MMA) chains as verified by FTIR and XPS spectroscopies, which to the best of our knowledge is the first time in the literature providing the direct evidence for the polymer chains grafting onto the exfoliated MMT. TEM investigation of the stretched nanocomposite film revealed that the microcracks in the nanocomposite film appeared mainly in the bulk region of polymer matrix, implying that the interfacial strength between P(MA‐co‐MMA) and its grafted MMT nanoplatelets was higher than the cohesion strength of P(MA‐co‐MMA). © 2009 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 47: 5891–5897, 2009     

Thermal curing behavior of MWCNT modified vinyl ester‐polyester resin suspensions prepared with 3‐roll milling technique

This study aims to investigate the curing behavior of a vinyl ester‐polyester resin suspensions containing 0.3 wt % of multiwalled carbon nanotubes with and without amine functional groups (MWCNTs and MWCNT‐NH₂). For this purpose, various analytical techniques, including Differential Scanning Calorimetry (DSC), Fourier infrared spectroscopy (FTIR), Raman Spectroscopy, and Thermo Gravimetric Analyzer (TGA) were conducted. The resin suspensions with carbon nanotubes (CNTs) were prepared via 3‐roll milling technique. DSC measurements showed that resin suspensions containing CNTs exhibited higher heat of cure (Q), besides lower activation energy (E_a) when compared with neat resin. For the sake of simplicity of interpretation, FTIR investigations were performed on neat vinyl ester resin suspensions containing the same amount of CNTs as resin. As a result, the individual fractional conversion rates of styrene and vinyl ester were interestingly found to be altered dependent on MWCNTs and MWCNT‐NH₂. The findings obtained from RS measurements of the cured samples are highly proportional to those obtained from FTIR measurements. TGA measurements revealed that CNT modified nanocomposites have higher activation energy of degradation (E_d) compared with the cured polymer. The findings obtained revealed that CNTs with and without amine functional groups alter overall thermal curing response of the surrounding matrix resin, which may probably impart distinctive characteristics to mechanical behavior of the corresponding nanocomposites achieved. © 2009 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 47: 1511–1522, 2009     

Enhanced β‐phase in PVDF polymer nanocomposite and its application for nanogenerator

Harvesting energy from the ambient mechanical energy by using flexible piezoelectric nanogenerator is a revolutionary step toward achieving reliable and green energy source. Polyvinylidene fluoride (PVDF), a flexible polymer, can be a potential candidate for the nanogenerator if its piezoelectric property can be enhanced. In the present work, we have shown that the polar crystalline β‐phase of PVDF, which is responsible for the piezoelectric property, can be enhanced from 48.2% to 76.1% just by adding ZnO nanorods into the PVDF matrix without any mechanical or electrical treatment. A systematic investigation of PVDF‐ZnO nanocomposite films by using X‐ray diffractometer, Fourier transform infrared spectroscopy, and polarization‐electric field loop measurements supports the enhancement of β‐phase in the flexible nanocomposite polymer films. The piezoelectric constant (d₃₃) of the PVDF‐ZnO (15 wt%) film is found to be maximum of approximately −1.17 pC/N. Nanogenerators have been fabricated by using these nanocomposite films, and the piezoresponse of PVDF is found to enhance after ZnO loading. A maximum open‐circuit voltage ~1.81 V and short‐circuit current of 0.57 μA are obtained for 15 wt% ZnO‐loaded PVDF nanocomposite film. The maximum instantaneous output power density is obtained as 0.21 μW/cm² with the load resistance of 7 MΩ, which makes it feasible for the use of energy harvesting that can be integrated to use for driving small‐scale electronic devices. This enhanced piezoresponse of the PVDF‐ZnO nanocomposite film‐based nanogenerators attributed to the enhancement of electroactive β‐phase and enhanced d₃₃ value in PVDF with the addition of ZnO nanorods.     

Cold‐drawn induced microstructure in PVC‐bentonite nanocomposites

The mechanical properties and cold drawn‐induced micro and nanostructure of polyvinyl chloride (PVC)‐bentonite nanocomposites have been investigated. Molded sheets with 5 wt% concentration of bentonite and two processing additives were melt extruded and two‐roll‐milled processed. The flame retardant additive promoted polymer intercalation whereas a pigment dispersant promoted clay exfoliation, the polymer matrix showed isotropic orientation. The intercalated nanocomposite exhibited nanoplates oriented with their planes parallel to the molded sheet surface and the Young's modulus and yield stress were significantly enhanced relative to neat PVC. The strain at fracture (～144%) was slightly reduced relative to the matrix (～167%). Cold drawing induced molecular chain orientation along the tensile axis and preserved the orientation of the intercalated nanoclays. The fracture mechanism, as investigated via scanning electron microscopy (SEM) revealed plastic fracture mechanism (similar to neat PVC). On the other hand, the exfoliated nanocomposite did not show any improvement in mechanical properties but rather a significant decay of strain at fracture (～44%). The fractured region, as examined by SEM, exhibited microvoid morphology. Analysis of the fractured region showed PVC macromolecules oriented along the tensile axis but no preferred orientation of the nanoclays. The limited strain at fracture found for this material appears to be associated with the initially randomly oriented nanoclays being unable to orient under the tensile deformation. The nanoclays would act as stress concentrators leading to rapid material's failure due to loss of adhesion with the polymer matrix. The results suggest that exfoliated nanoclays could play a detrimental role when the nanocomposite is subjected to large deformations at temperatures well within the glassy regime. Copyright © 2009 John Wiley & Sons, Ltd.     

Investigating properties of poly (ether‐amide)/MWCNT nanocomposite films containing 2,7‐bis(4‐aminophenoxy)naphthalene and isophthalic segments

Three nanocomposite films based on aramid (poly (ether‐amide), PEA) and multiwall carbon nanotubes (MWCNT) were prepared via solution casting method using 2,7‐bis(4‐aminophenoxy)naphthalene (4) and isophthalic acid (5) containing various amounts of MWCNT (2, 3, 5 wt.%). To comprehensively analyze the properties of the cast films as well as the monomers, different techniques were employed, namely FT‐IR, ¹H NMR, X‐ray diffraction, and field emission scanning electron microscopy. Also, thermal and tensile properties of PEA (6) and nanocomposite films were investigated using thermogravimetric analysis and mechanical analysis, respectively. The morphology, thermal, and mechanical properties of nanocomposite films approved that MWCNT had well dispersion in the PEA matrix and showed a synergistic effect on improving all of the investigated properties. Based on the thermogravimetric analysis results, employing MWCNT caused to increase in the char yields from 61 (in the neat PEA) to 66 (in the PEA /MWCNT nanocomposite 5 wt.%) under the nitrogen atmosphere. In comparison to the pristine PEA (426°C), the temperature at 10 losses mass % (T₁₀) was increased from 530°C to 576°C, with 2 to 5 wt.% of MWCNT. Mechanical analysis revealed that the tensile strength and initial modulus were improved by incorporating MWCNT into PEA (81.70–93.40 MPa and 2.10–2.22 GPa, respectively). Electrical conductivity of the PEA/MWCNT nanocomposites was displayed maximum value in the 5 wt.%, showing satisfactory value in many application areas. The X‐ray diffraction technique was employed to study the crystalline structure of the prepared nanocomposite films as well as PEA. In addition, the electrochemical impedance spectroscopy study demonstrated that the prepared nanocomposites had significant impedance improvement in the presence of MWCNTs.     

Competition between supernucleation and plasticization in the crystallization and rheological behavior of PCL/CNT‐based nanocomposites and nanohybrids

PCL was blended with pristine multiwalled carbon nanotubes (MWCNT) and with a nanohybrid obtained from the same MWCNT but grafted with low molecular weight PCL, employing concentrations of 0.25 to 5 wt % of MWCNT and MWCNT‐g‐PCL. Excellent CNT dispersion was found in all samples leading to supernucleation of both nanofiller types. Nanohybrids with 1 wt % or less MWCNTs crystallize faster than nanocomposites (due to supernucleation), while the trend eventually reverses at higher nanotubes content (because of plasticization). Rheological results show that yield‐like behavior develops in both nanocomposites, even for the minimum content of carbon nanotubes. In addition, the MWCNT‐g‐PCL family, when compared with the neat polymer, exhibits lower values of viscosity and modulus in oscillatory shear, and higher compliance in creep. These rheological differences are discussed in terms of the plasticization effect caused by the existence of low molecular weight free and grafted PCL chains in the nanohybrids. © 2017 Wiley Periodicals, Inc. J. Polym. Sci., Part B: Polym. Phys. 2017 , 55, 1310–1325     

Enhanced dielectric properties of polymer composite films induced by encapsulated MWCNTs with a one core‐two shell structure

Multiwalled carbon nanotubes (MWCNTs) can endow high dielectric constant to polymer‐based composites. However, the accompanying poor dispersion of MWCNTs and high dielectric loss for composites severely limit their application in dielectric field. Herein, a modified acid‐treated MWCNTs encapsulated by the polyaniline/poly(sodium 4‐styrenesulfonate) layers (aMWCNTs@PANI‐PSS) with a one core‐two shell structure was fabricated by in situ polymerization followed by electrostatic self‐assembly technique. Furthermore, the composite films based on aMWCNTs@PANI‐PSS/poly(vinylidenefluoride‐hexaflouropropylene) (PVDF‐HFP) were fabricated by a solution‐casting method. An ultrathin insulating PSS shell is wrapped onto aMWCNTs@PANI, resulting in the improvement of dispersibility for aMWCNTs@PANI and the decrease of dielectric loss for composite films. When the content of aMWCNTs@PANI‐PSS is 5.0 wt %, the dielectric constant of aMWCNTs@PANI‐PSS/PVDF‐HFP reaches 430 (100 Hz), which is about 55 times of pure PVDF‐HFP and 1.7 times of aMWCNTs@PANI/PVDF‐HFP (247). Besides, the responding dielectric loss of aMWCNTs@PANI‐PSS/PVDF‐HFP composite film is only 0.67, much lower than that of aMWCNTs@PANI/PVDF‐HFP (25) and aMWCNTs/PVDF‐HFP (3185). © 2017 Wiley Periodicals, Inc. J. Polym. Sci., Part B: Polym. Phys. 2017 , 55, 948–956     

Morphology and permeability of exfoliated PVAc‐MMT nanocomposite films cast from soap‐free emulsion‐polymerized latices

In this study, we exclusively found that the exfoliated poly(vinyl acetate)‐montmorillonite (PVAc‐MMT) nanocomposite latices could be straightforwardly fabricated by soap‐free emulsion polymerization and cast into a film. The as‐fabricated films were transparent with the exfoliated MMT nanoplatelets in flat form uniformly dispersed in the PVAc matrix. Certain bonding of PVAc matrix to the exfoliated MMT nanoplatlets refrained it from removal by acetone in Soxhlet extraction. Exfoliated MMT nanoplatlets (10 wt %) in the film was able to reduce the water vapor permeability coefficient to only 9% that of the neat PVAc. According to the generalized Nielsen's permeability model for the composites containing impermeable fillers in sheet form, the average aspect ratio of exfoliated MMT platelets was calculated as 327, similar to those directly estimated by atomic force microscopy and transmission electron microscopy. © 2007 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 45: 5583–5589, 2007     

Core–shell functionalized MWCNT/poly(m‐aminophenol) nanocomposite with large dielectric permittivity and low dielectric loss

Core–shell carboxyl‐functionalized multiwall carbon nanotube (c‐MWCNT)/poly(m‐aminophenol) (PmAP) nanocomposite were prepared through in‐situ polymerization of m‐aminophenol (m‐AP) in the presence of MWCNTs, and explicated as a dielectric material for electronic applications. The formation of thin PmAP layer on individual c‐MWCNT with excellent molecular level interactions at interfaces was confirmed by morphological and spectroscopic analyses. Here we conducted a comparative study of the dielectric performances of PmAP based nanocomposite films with pristine MWCNTs and c‐MWCNTs as fillers. Compared to PmAP/MWCNT nanocomposites, the PmAP/c‐MWCNT nanocomposites exhibited higher dielectric permittivity and lower dielectric loss. The well dispersed c‐MWCNTs in PmAP/c‐MWCNT nanocomposite produce huge interfacial area together with numerous active polarized centers (crystallographic defects), which in turn intensified the Maxwell‐Wagner‐Sillars (MWS) effect based on excellent molecular level interactions and thus, produce large dielectric permittivity (8810 at 1 kHz). The percolation threshold of PmAP/c‐MWCNT nanocomposites is found lower than that of the PmAP/MWCNT nanocomposites, which could be attributed to homogeneous distribution of c‐MWCNTs and strong c‐MWCNT//PmAP interfacial interactions in the nanocomposites. Copyright © 2016 John Wiley & Sons, Ltd.     

Structural and morphological studies on the deformation behavior of polypropylene/multi‐walled carbon nanotubes nanocomposites prepared through ultrasound‐assisted melt extrusion process

Structural and morphological behavior under stress–strain of polypropylene/multi‐walled carbon nanotubes (PP/MWCNTs) nanocomposites prepared through ultrasound‐assisted melt extrusion process was studied by means of optical microscopy, scanning electron microscopy, transmission electron microscopy, Raman spectroscopy, small angle X‐ray scattering (SAXS), and wide angle X‐ray scattering (WAXS). A high ductile behavior was observed in the PP/MWCNT nanocomposites with low concentration of MWCNTs. This was related to an energy‐dissipating mechanism, achieved by the formation of an ordered PP‐CNTs interphase zone and crystal oriented structure in the undeformed samples. Different strain‐induced‐phase transformations were observed by ex situ SAXS/WAXS, characterizing the different stages of structure development during the deformation of PP and PP/MWCNTs nanocomposites. The high concentration of CNTs reduced the strain behavior of PP due to the agglomeration of nanoparticles. A structural pathway relating the deformation‐induced phase transitions and the dissipation energy mechanism in the PP/MWCNTs nanocomposites at low concentration of nanoparticles was proposed. © 2014 Wiley Periodicals, Inc. J. Polym. Sci., Part B: Polym. Phys. 2015 , 53, 475–491     

Synthesis and studies of thermal,mechanical and electrical properties of MWCNT–cyclodextrin as a nanoparticle in polyamide matrix based on 2,2‐Bis[4‐(4‐aminophenoxy)phenyl] propane

In the present research, polyamide (PA) ( 6 ) was synthesized by the polycondensation reaction of 2,2‐Bis[4‐(4‐aminophenoxy)phenyl] propane as a diamine ( 4 ) with adipic acid ( 5 ) in the optimized condition. The resulting PA was characterized using Fourier transform infrared spectroscopy, Proton Nuclear Magnetic Resonance (¹H NMR) spectroscopy, inherent viscosity (η_inh), X‐ray diffraction, and solubility tests. Also, the thermal property of the new PA ( 6 ) was investigated by using Thermogravimetric analysis. To apply multiwall carbon nanotube (MWCNT) as an effective reinforcement in polymer composites, it is essential to have appropriate proper dispersion, interfacial adhesion between the MWCNT and polymer matrix, and increasing solubility. With this end particularly, functionalized MWCNTs were combined with a soluble molecule, and a series of modified MWCNT with cyclodextrin (Cy) known as PA/MWCNT‐Cy composite film (2, 5, and 8 wt%) were prepared by a solution intercalation technique. Field emission scanning electron microscopy images showed that MWCNT‐Cy was well dispersed in the PA matrix. Thermogravimetric analysis indicated an increase in thermal stability of nanocomposites as compared with the pristine PA. Anisotropic structure of the synthesized films and dispersed MWCNT‐Cy in the films approved by use of X‐ray diffraction and field emission scanning electron microscopy. The resultant PA/MWCNT‐Cy composite films were electrically conductive, which is favorable for many practical uses. Measurements of mechanical properties of these composite films showed high strength in 8% MWCNT‐Cy content. Also, results showed increases in Young's modulus and tensile strength. Copyright © 2016 John Wiley & Sons, Ltd.