Investigation of sequence isomer effects in AB‐polybenzimidazole polymers

In the present work, a unique series of random polybenzimidazole (PBI) copolymers consisting of the recently reported novel isomeric AB‐PBI (i‐AB‐PBI) and the well known AB‐PBI were synthesized. The i‐AB‐PBI incorporates additional linkages (2,2 and 5,5) in the benzimidazole sequence when compared with AB‐PBI. Random copolymers, varying in composition at 10 mol % increments, were synthesized to evaluate the effects of sequence isomerism in the polymer main chain without altering the fundamental chemical composition or functionality of a polymer chain consisting of 2,5‐benzimidazole units. Polymer solutions were prepared in polyphosphoric acid (PPA) and cast into membranes using the sol–gel PPA process. The resulting polymers were found to have high inherent viscosities (>2.0 dL/g) and showed elevated membrane proton conductivities (～0.2 S/cm) under anhydrous conditions at 180 °C. Fuel cell performance evaluations were conducted, and an average output voltage ranging from 0.5 to 0.60 V at 0.2 A/cm² was observed for hydrogen/air at an operational temperature of 180 °C without applied backpressure or humidification. Herein, we report for the first time glass transition (T_g) temperatures for AB‐PBI, i‐AB‐PBI, and an anomalous T_g effect for the series of randomized PBIs. © 2013 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2014 , 52, 619–628     

Synthesis and characterization of high molecular weight hexafluoroisopropylidene‐containing polybenzimidazole for high‐temperature polymer electrolyte membrane fuel cells

A high molecular weight, thermally and chemical stable hexafluoroisopropylidene containing polybenzimidazole (6F‐PBI) was synthesized from 3,3′‐diaminobenzidine (TAB) and 2,2‐bis(4‐carboxyphenyl) hexafluoropropane (6F‐diacid) using polyphosphoric acid (PPA) as both the polycondensation agent and the polymerization solvent. Investigation of polymerization conditions to achieve high molecular weight polymers was explored via stepwise temperature control, monomer concentration in PPA, and final polymerization temperature. The polymer characterization included inherent viscosity (I.V.) measurement and GPC as a determination of polymer molecular weight, thermal and chemical stability assessment via thermo gravimetric analysis and Fenton test, respectively. The resulting high molecular weight polymer showed excellent thermal and chemical stability. Phosphoric acid doped 6F‐PBI membranes were prepared using the PPA process. The physiochemical properties of phosphoric acid doped membranes were characterized by measuring the phosphoric acid doping level, mechanical properties, and proton conductivity. These membranes showed higher phosphoric acid doping levels and higher proton conductivities than the membranes prepared by the conventional membrane fabrication processes. These membranes had sufficient mechanical properties to be easily fabricated into membrane electrode assemblies (MEA) and the prepared MEAs were tested in single cell fuel cells under various conditions, with a focus on the high temperature performance and fuel impurity tolerance. © 2009 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 47: 4064–4073, 2009     

Synthesis of Novel Chiral Biphenylamine Ligand 6,6'‐Dimethoxy‐2,2′‐diaminobiphenyl

A new chiral ligand 6,6′‐dimethoxy‐2,2′‐diaminobiphenyl was successfully prepared from 3‐nitrophenol via iodination, Ullmann coupling, and reduction. The resolving reagent (2R, 3R)‐ or (2S,3S)‐2,3‐di (phenylaminocarbonyl)tartaric acid was prepared from commercially available tartaric acid in large scale and was used to resolve the racemic 6,6′‐dimethoxy‐2,2′‐diaminobiphenyl. The chiral 6,6′‐ dimethoxy‐2,2′‐diaminobiphenyl obtained was proved to be enantiomerically pure.     

Synthesis of reactive three‐arm star‐shaped oligoimides with narrow molecular weight distribution

Series of star‐shaped three arms oligoimides (SOI) with terminal amino groups with narrow MWD ((M_w/M_n = 1.1–2) was synthesized by the one‐stage high‐temperature polycondensation in molten benzoic acid at 140 °C. The (B3+AB′) approach with the “slow addition of monomer” method was used for this synthesis, where B3 is 2,4,6‐tris(4‐aminophenoxy)toluene and AB′ is 3‐aminophenoxy phthalic acid. The SOI arm's length was controlled by the AB′/B3 mole ratio of 10:1, 20:1, 40:1, and 100:1. By the reaction of SOI's terminal amino groups with acetic anhydride, corresponding acetamide derivatives were obtained. SOI synthesized are soluble in selected organic solvents. © 2018 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2018 , 56, 2004–2009     

Synthesis and properties of a new fluorine‐containing polybenzimidazole for high‐temperature fuel‐cell applications

An amorphous, organosoluble, fluorine‐containing polybenzimidazole (PBI) was synthesized from 3,3′‐diaminobenzidine and 2,2‐bis(4‐carboxyphenyl)hexafluoropropane. The polymer was soluble in N‐methylpyrrolidinone and dimethylacetamide and had an inherent viscosity of 2.5 dL/g measured in dimethylacetamide at a concentration of 0.5 g/dL. The 5% weight loss temperature of the polymer was 520 °C. Proton‐conducting PBI membranes were prepared via solution casting and doped with different amounts of phosphoric acid. In the methanol permeability measurement, the PBI membranes showed much better methanol barrier ability than a Nafion membrane. The proton conductivity of the acid‐doped PBI membranes increased with increasing temperatures and concentrations of phosphoric acid in the polymer. The PBI membranes showed higher proton conductivity than a Nafion 117 membrane at high temperatures. © 2006 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 44: 4508–4513, 2006     

Synthesis and characterization of thermally stable sulfonated polybenzimidazoles obtained from 3,3′‐disulfonyl‐4,4′‐dicarboxyldiphenylsulfone

A novel sulfonated aromatic diacid, 3,3′‐disulfonyl‐4,4′‐dicarboxyldiphenylsulfone (DSDCDPS), was successfully synthesized from 4,4′‐dimethyldiphenylsulfone by sulfonation and further oxidation. A series of sulfonated polybenzimidazoles (sPBI‐SS) with various sulfonation degrees was prepared from DSDCDPS, 4,4′‐sulfonyldibenzoic acid and 3,3′‐diaminobenzidine by solution copolycondensation in poly(phosphoric acid). The chemical structure of the resulting sPBI‐SS was confirmed by FTIR and ¹H NMR. The DSDCDPS‐based sPBI‐SS with the number‐average molecular weights of 32,000–55,000 were easy to dissolve in polar aprotic solvents such as DMF, DMSO, and DMAc, and could be cast into transparent, tough, and flexible membranes. The membranes presented good thermal stabilities (5% weight loss temperatures higher than 430 °C), and the thermal degradation activation energies of the sulfonic group of sPBI‐SS40 evaluated under N₂ by both Ozawa and Kissinger methods were 266.06 and 264.79 kJ/mol, respectively. The membranes also exhibited high storage moduli, glass transition temperatures (above 238 °C) and tensile strengths (～80 MPa), in addition to water uptakes (22.3–25.2%) and low swelling degrees (<14.0%). © 2005 Wiley Periodicals, Inc. J Polym Sci A: Polym Chem 43: 4363–4372, 2005     

Preparation and physical properties of poly(4,4′‐diamino‐3′‐carbamoylbenzanilide terephthalamide) and poly(4,4′‐diamino‐3′‐carbamoylbenzanilide isophthalamide) films

To prepare thermally stable and high‐performance polymeric films, new solvent‐soluble aromatic polyamides with a carbamoyl pendant group, namely poly(4,4′‐diamino‐3′‐carbamoylbenzanilide terephthalamide) (p‐PDCBTA) and poly(4,4′‐diamino‐3′‐carbamoylbenzanilide isophthalamide) (m‐PDCBTA), were synthesized. The polymers were cyclized at around 200 to 350 °C to form quinazolone and benzoxazinone units along the polymer backbone. The decomposition onset temperatures of the cyclized m‐ and p‐PDCBTAs were 457 and 524 °C, respectively, lower than that of poly(p‐phenylene terephthalamide) (566 °C). For the p‐PDCBTA film drawn by 40% and heat‐treated, the tensile strength and Young's modulus were 421 MPa and 16.4 GPa, respectively. The film cyclized at 350 °C showed a storage modulus (E′) of 1 × 10¹¹ dyne/cm² (10 GPa) over the temperature range of room temperature to 400 °C. © 2000 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 38: 775–780, 2000     

Synthesis and properties of noncoplanar rigid‐rod aromatic polyhydrazides and poly(1,3,4‐oxadiazole)s containing phenyl or naphthyl substituents

Two new phenyl‐ and naphthyl‐substituted rigid‐rod aromatic dicarboxylic acid monomers, 2,2′‐diphenylbiphenyl‐4,4′‐dicarboxylic acid ( 4 ) and 2,2′‐di(1‐naphthyl)biphenyl‐4,4′‐dicarboxylic acid ( 5 ), were synthesized by the Suzuki coupling reaction of 2,2′‐diiodobiphenyl‐4,4′‐dicarboxylic acid dimethyl ester with benzeneboronic acid and naphthaleneboronic acid, respectively, followed by alkaline hydrolysis of the ester groups. Four new polyhydrazides were prepared from the dicarboxylic acids 4 and 5 with terephthalic dihydrazide (TPH) and isophthalic dihydrazide (IPH), respectively, via the Yamazaki phosphorylation reaction. These polyhydrazides were amorphous and readily soluble in many organic solvents. Differential scanning calorimetry (DSC) indicated that these hydrazide polymers had glass transition temperatures in the range of 187–234 °C and could be thermally cyclodehydrated into the corresponding oxadiazole polymers in the range of 300–400 °C. The resulting poly(1,3,4‐oxadiazole)s exhibited T_g's in the range of 252–283 °C, 10% weight‐loss temperature in excess of 470 °C, and char yield at 800 °C in nitrogen higher than 54%. These organo‐soluble polyhydrazides and poly(1,3,4‐oxadiazole)s exhibited UV–Vis absorption maximum at 262–296 and 264–342 nm in NMP solution, and their photoluminescence spectra showed maximum bands around 414–445 and 404–453 nm, respectively, with quantum yield up to 38%. The electron‐transporting properties were examined by electrochemical methods. Cyclic voltammograms of the poly(1,3,4‐oxadiazole) films cast onto an indium‐tin oxide (ITO)‐coated glass substrate exhibited reversible reduction redox with E_onset at ?1.37 to ?1.57 V versus Ag/AgCl in dry N,N‐dimethylformamide solution. © 2006 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 44: 6466–6483, 2006     

Synthesis and properties of novel polyimides derived from 2,2′,3,3′‐benzophenonetetracarboxylic dianhydride

A new synthetic route to 2,2′,3,3′‐BTDA (where BTDA is benzophenonetetracarboxylic dianhydride), an isomer of 2,3′,3′,4′‐BTDA and 3,3′,4,4′‐BTDA, is described. Single‐crystal X‐ray diffraction analysis of 2,2′,3,3′‐BTDA has shown that this dianhydride has a bent and noncoplanar structure. The polymerizations of 2,2′,3,3′‐BTDA with 4,4′‐oxydianiline (ODA) and 4,4′‐bis(4‐aminophenoxy)benzene (TPEQ) have been investigated with a conventional two‐step process. A trend of cyclic oligomers forming in the reaction of 2,2′,3,3′‐BTDA and ODA has been found and characterized with IR, NMR, matrix‐assisted laser desorption/ionization time‐of‐flight mass spectrometry, and elemental analyses. Films based on 2,2′,3,3′‐BTDA/TPEQ can only be obtained from corresponding polyimide (PI) solutions prepared by chemical imidization because those from their polyamic acids by thermal imidization are brittle. PIs from 2,2′,3,3′‐BTDA have lower inherent viscosities and worse thermal and mechanical properties than the corresponding 2,3′,3′,4′‐BTDA‐ and 3,3′,4,4′‐BTDA‐based PIs. PIs from 2,2′,3,3′‐BTDA and 2,3′,3′,4′‐BTDA are amorphous, whereas those from 3,3′,4,4′‐BTDA have some crystallinity, according to wide‐angle X‐ray diffraction. Furthermore, PIs from 2,2′,3,3′‐BTDA have better solubility, higher glass‐transition temperatures, and higher melt viscosity than those from 2,3′,3′,4′‐BTDA and 3,3′,4,4′‐BTDA. Model compounds have been prepared to explain the order of the glass‐transition temperatures found in the isomeric PI series. The isomer effects on the PI properties are discussed. © 2004 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 42: 2130–2144, 2004     

Improved conditions for fluorescent staining of proteins with 4,4′‐dianilino‐1,1′‐binaphthyl‐5,5′‐disulfonic acid in SDS‐PAGE

A simple and sensitive fluorescent staining method for the detection of proteins in SDS‐PAGE, namely IB (improved 4,4′‐dianilino‐1,1′‐binaphthyl‐5,5′‐disulfonic acid) stain, is described. Non‐covalent hydrophobic probe 4,4′‐dianilino‐1,1′‐binaphthyl‐5,5′‐disulfonic acid was applied as a fluorescent dye, which can bind to hydrophobic sites in proteins non‐specifically. As low as 1 ng of protein band can be detected briefly by 30 min washing followed by 15 min staining without the aiding of stop or destaining step. The sensitivity of the new presented protocol is similar to that of SYPRO Ruby, which has been widely accepted in proteomic research. Comparative analysis of the MS compatibility of IB stain and SYPRO Ruby stain allowed us to address that IB stain is compatible with the downstream of protein identification by PMF.     

High temperature creep behavior of phosphoric acid‐polybenzimidazole gel membranes

This work investigates the effects of polymer solids content and macromolecular structure on the high temperature creep behavior of polybenzimidazole (PBI) gel membranes imbibed with phosphoric acid (PA) after preparation via a polyphosphoric acid (PPA) mediated sol‐gel process Low‐solids, highly acid‐doped PBI membranes demonstrate outstanding fuel cell performance under anhydrous, ambient pressure, and high temperature (120–200 °C) operating conditions. However, PBI membranes are susceptible to creep under compressive loads at elevated temperatures, so their long‐term mechanical durability is a major concern. Here, we report results for the creep behavior of PBI membranes subject to compression at 180 °C. For para‐ and meta‐PBI homopolymers, increasing polymer solids content results in lower creep compliance and higher extensional viscosity, which may be rationalized by increasing chain density in the sol‐gel network. Comparing various homo‐ and copolymers at similar solids loading, differences in creep behavior may be rationalized in terms of chain–chain and chain‐solvent interactions that control macromolecular solubility and stiffness in the PA solvent. The results demonstrate the feasibility of improving the mechanical properties of PA‐doped PBI membranes by control of polymer solids content and rational design of PBI macromolecular structure. © 2015 Wiley Periodicals, Inc. J. Polym. Sci., Part B: Polym. Phys. 2015 , 53, 1527–1538     

A comparison of the properties of two structurally equivalent but regiochemically different mono‐alkylated polybithiophenes prepared through AABB‐type stille polycondensation

Previous routes to polymers with mono‐alkylated bithiophenes have proceeded through polymerization of monoalkyl‐2,2′‐bithiophene monomers through oxidative or AB‐type cross‐coupling polymerizations. The resulting polymer regiochemistry affects both the location and orientation of the polymer side‐chains. In contrast, AABB‐type cross‐coupling polymerizations can control the location and in some cases the orientation of the side‐chains. To study how this control can impact polymer properties, two poly(monodecyl‐2,2′‐bithiophene) polymers have been synthesized through Stille AABB‐type polycondensations of 2,5‐bis(trimethylstannyl)thiophene with different monomers. The alkyl side‐chains are located on every other thiophene, but polymer 1 consists of both head‐to‐tail and head‐to‐head dyads, whereas polymer 2 is made up of only head‐to‐head dyads. ¹H NMR, ¹³C NMR, and heteronuclear single quantum correlation spectroscopy are used to confirm and contrast the polymer regiochemistries. The physical properties of the two polymers are analyzed using UV–vis spectroscopy, differential scanning calorimetry, and grazing‐incidence X‐ray diffraction. Polymer 2 is found to display significantly more aggregation in solution than 1, and it displays different thermal properties. The film properties of polymers 1 and 2, however, are very similar, with nearly identical UV–vis profiles and d‐spacing values as determined by grazing incidence X‐ray diffraction. © 2012 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2013     

Synthesis and micropatterning properties of a novel base‐soluble,positive‐working,photosensitive polyimide having an o‐nitrobenzyl ether group

A novel positive‐working, photosensitive polyimide, poly[1,4‐phenyleneoxy‐1,4‐phenylene‐2,2′‐di(2‐nitrobenzyloxy)benzophenone‐3,3′,4,4′‐tetracarboxdiimide] (OPI‐Nb), developable with an aqueous base was prepared by the o‐nitrobenzylation of a polyimide, poly(1,4‐phenyleneoxy‐1,4‐phenylene‐2,2′‐dihydroxybenzophenone‐3,3′,4,4′‐tetracarboxdiimide) (OPI), derived from 2,2′‐dihydroxy‐3,3′,4,4′‐benzophenonetetracarboxylic dianhydride (DHBA) and 4,4′‐oxydianiline, and it micropatterning properties were investigated. The o‐nitrobenzylation of OPI to OPI‐Nb was conducted with o‐nitrobenzyl bromide in N‐methyl‐2‐pyrrolidinone containing Et₃N. The DHBA monomer was synthesized by exhaustive KMnO₄ oxidation of bis(2‐dimethoxy‐3,4‐dimethylphenyl)methane obtained by etherification of bis(2‐hydroxy‐3,4‐dimethylphenyl)methane with iodomethane, followed by deprotection of the methoxy groups and cyclodehydration of the obtained 2,2′‐dihydroxy‐3,3′4,4′‐benzophenonetetracarboxylic acid. The intermediate bis(2‐hydroxy‐3,4‐dimethylphenyl)methane was prepared by the condensation of 2,3‐dimethylphenol with paraformaldehyde. The degree of o‐nitrobenzylation was determined to be over 94 mol % from ¹H NMR absorption of benzylic CH₂ protons. The aromatic OPI was perfectly soluble in a dilute aqueous NaOH solution and tetramethylammonium hydroxide (TMAH), whereas OPI‐Nb was not even swellable in them. In the micropatterning process, OPI‐Nb showed a line‐width resolution of 0.4‐μm and a sensitivity of 5.4 J/cm² when its thin films were irradiated with 365‐nm light and developed with a 2.38% aqueous TMAH solution at room temperature for 90 s. The thickness loss of OPI‐Nb films measured after postbaking at 350 °C was in the 8–9% range. © 2007 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 45: 776–788, 2007     

The amplified circularly polarized luminescence emission response of chiral 1,1′‐binaphthol‐based polymers via Zn(II)‐coordination fluorescence enhancement

Two kinds of chiral 1,1′‐binaphthol (BINOL)‐based polymer enantiomers were designed and synthesized by the polymerization of 5,5′‐((2,2′‐bis (octyloxy)‐[1,1′‐binaphthalene]‐3,3′‐diyl)bis(ethyne‐2,1‐diyl))bis(2‐hydroxybenzaldehyde) ( M1 ) with alkyl diamine ( M2 ) via nucleophilic addition–elimination reaction. The resulting chiral polymers can exhibit mirror image cotton effects either in the absence or in the presence of Zn²⁺ ion. Almost no fluorescence or circularly polarized luminescence (CPL) emission could be observed for two chiral BINOL‐based polymer enantiomers in the absence of Zn²⁺. Interestingly, the chiral polymers can show strong fluorescence and CPL response signals upon the addition of Zn²⁺, which can be attributed to Zn²⁺‐coordination fluorescence enhancement effect. This work can develop a new strategy on the design of the novel CPL materials via metal‐coordination reaction. © 2018 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2018 , 56, 1282–1288     

Synthesis and characterization of a series of wholly aromatic copolyesters containing 2‐(α‐phenylisopropyl)hydroquinone moiety

Two series of new wholly aromatic thermotropic copolyesters containing the 2‐(α‐phenylisopropyl)hydroquinone (PIHQ) moiety have been synthesized and their basic properties such as glass transition temperature (T_g), melting temperature (T_m), thermal stability, crystallinity, and liquid crystallinity were studied by differential scanning calorimetry (DSC), thermogravimetry (TG), and wide‐angle X‐ray diffractometry (WAXD) and on a polarizing microscope. The first series was prepared from acetylated PIHQ, terephthalic acid (TPA), and 2,6‐naphthalenedicarboxylic acid (NDA), and the second series from acetylated PIHQ, TPA, and 1,1′‐biphenyl‐4,4′‐dicarboxylic acid (BDA). The T_g values (152–168°C) of the two series are not much different, although the values for the first series appear slightly higher. The T_m values (287–378°C) and the degree of crystallinity of the first series are appreciably greater than those of the second series. Such differences can be explained by the geometric structure of NDA and BDA moieties. All of the present polyesters are thermotropic and nematic. © 1999 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 37: 881–889, 1999     

Synthesis,Characterization and Reactions of 4‐Hydrazino‐2‐methylpyrimidino[4′5′:4,5]thiazolo[3,2‐a]benzimidazole

4‐Hydrazino‐2‐methylpyrimidino[4′,5′:4,5]thiazolo[3,2‐a]benzimidazole ( 4 ) was obtained from hydrazinolysis of the 4‐chloro derivative 3 with hydrazine hydrate. The hydrazino derivative 4 was further cyclized to the corresponding pyrazole 5 , pyrazolone 6 and 5‐methyl‐1,2,4‐triazolo[1″,5″:3′,4′]pyrimidino[5′,6′:5,4]‐thiazolo[3,2‐a]benzimidazole ( 9 ) and 5‐methy‐1,2,4‐triazolo[4″,3″:3′,4′]pyrimidino[5′,6′:5,4]thiazolo‐[3,2‐a]benzimidazole ( 10 ), respectively. The triazolo derivative 10 was isomerized to the triazolo derivative 9 under a variety of reaction conditions.     

The kinetics of polycondensation of α,α′‐dichloro‐p‐xylene with 4,4′‐isopropylidenediphenol using benzyltriethylammonium chloride as a phase‐transfer catalyst

The phase‐transfer catalyzed polycondensation of α,α′‐dichloro‐p‐xylene with 4,4′‐isopropylidenediphenol was carried out using benzylethylammonium chloride in a two‐phase system of an aqueous alkaline solution and benzene at 60 °C under nitrogen atmosphere. The rate of polycondensation was expressed as the combined terms of quaternary onium cation and 4,4′‐isopropylidenediphenolate anion rather than the feed concentration of catalyst and 4,4′‐isopropylidenediphenol. The measured concentrations of hydroxide and chloride anion in the aqueous solution and α,α′‐dichloro‐p‐xylene in the organic phase were used to obtain the reaction rate constant with the integral method, and to analyze the polycondensation mechanism with a cyclic phase‐transfer initiation step in the heterogeneous liquid–liquid system. © 2000 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 38: 3059–3066, 2000     

Thermal and infrared spectroscopic studies on hydrogen‐bonding interactions between poly‐(ε‐caprolactone) and some dihydric phenols

The effects of three dihydric phenols on the thermal properties of poly‐(ε‐caprolactone) (PCL) were investigated by DSC. The thermal properties of PCL were found to be greatly modified by the addition of 4,4′‐dihydroxydiphenyl ether (DHDPE). When the content of DHDPE reached 40%, PCL that was a semicrystalline polymer in the pure state changed to a fully amorphous elastomer. Fourier transform infrared (FTIR) spectroscopy was also applied to investigate the specific interaction between PCL and DHDPE. The formations of intermolecular hydrogen bonds between the carbonyl groups of PCL and the hydroxyl groups of DHDPE were discovered. By applying the Beer–Lambert law and a curve‐fitting program, the fractions of hydrogen‐bonded carbonyl groups were quantitatively analyzed. Although one DHDPE molecule had the potentiality to form two hydrogen bonds with PCL chains, the values of the fraction of the hydroxyl group involved in the intermolecular hydrogen bond were so little that from a statistical point of view, the formation of two hydrogen bonds was very difficult for every DHDPE molecule. Both DSC and FTIR revealed that 4,4′‐dihydroxydiphenyl methane and 4,4′‐dihydroxyphenyl had the ability to form hydrogen bonds with PCL, which were strongly affected by the polarity of the group linking two hydroxyphenyls and the flexibility of the molecular chain. The stronger the polarity of the group and the better the flexibility of molecular chain, the more tendencies dihydric phenol had to form intermolecular hydrogen bonds with PCL. © 2001 John Wiley & Sons, Inc. J Polym Sci Part B: Polym Phys 39: 2108–2117, 2001     

Solution polymerization of polybenzimidazole

Polybenzimidazoles (PBI) are an important class of heterocyclic polymers that exhibit high thermal and oxidative stabilities. The two dominant polymerization methods used for the synthesis of PBI are the melt/solid polymerization route and solution polymerization using polyphosphoric acid as the solvent. Both methods have been widely used to produce high‐molecular weight PBI, but also highlight the obvious absence of a practical organic solution‐based method of polymerization. This current work explores the synthesis of high‐molecular weight meta‐PBI in N,N‐dimethyl acetamide (DMAc). Initially, model compound studies examined the reactivity of small molecules with various chemical functionalities that could be used to produce 2‐phenyl‐benzimidazole in high yield with minimal side reactions. ¹H NMR and FTIR studies indicated that benzimidazoles could be efficiently synthesized in DMAc by reaction of an o‐diamine and the bisulfite adduct of an aromatic aldehyde. Polymerizations were conducted at various polymer concentrations (2‐26 wt % polymer) using difunctional monomers to optimize reaction conditions in DMAc which resulted in the preparation of high‐molecular weight m‐PBI (inherent viscosities up to 1.3 dL g^?1). TGA and DSC confirmed that m‐PBI produced via this route has comparable properties to that of commercial m‐PBI. This method is advantageous in that it not only allows for high‐polymer concentrations of m‐PBI to be synthesized directly and efficiently, but can be applied to the synthesis of many PBI derivatives. © 2016 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2016 , 54, 1795–1802     

Synthesis and characterization of light‐emitting main‐chain metallo‐polymers containing bis‐terpyridyl ligands with various lateral substituents

A series of conjugated monomers ( 5a‐5d ) with various lateral substituents were symmetrically synthesized by the Sonogashira coupling reaction, in which central aromatic units (i.e. 9,9‐dipropylfluorenes) were linked to 2,2′:6′,2′‐terpyridyl (tpy) units via phenylene/ethynylene fragments. These light‐emitting monomers were further reacted with zinc(II) ions and subsequently anion exchanged to produce supramolecular main‐chain metallo‐polymers ( 6a‐6d ). The formation of polymers 6a‐6d was confirmed by the increased viscosities (up to 1.5–1.83 times) relative to those of their analogous monomers. The results of ¹H NMR titration and UV‐Vis spectral titration revealed a detailed complexation process of metallo‐polymers by varying the molar ratios of zinc(II) ions to monomers. After coordination with zinc(II) ions, the luminescent and thermal properties of the polymers were enhanced by the formation of metallo‐supramolecular structures in contrast to their monomer counterparts. PLED devices employing these metallo‐polymers as emitters gave yellow to orange electroluminescence (EL) emissions with turn‐on voltages around 6 V. The maximum power efficiency, external quantum yield, and brightness of the PLED device containing polymer 6c were 0.33 cd A^?1 (at 14 V), 1.02%, and 931 cd m^?2 (at 14 V), respectively. © 2007 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 45: 3243–3255, 2007