Synthesis,characterization, and electrical properties of polypyrrole/multiwalled carbon nanotube composites

Size‐controllable polypyrrole (PPy)/multiwalled carbon nanotube (MWCNT) composites have been synthesized by in situ chemical oxidation polymerization directed by various concentrations of cationic surfactant cetyltrimethylammonium bromide (CTAB). Raman spectra, FTIR, SEM, and TEM were used to characterize their structure and morphology. These results showed that the composites are core (MWCNT)–shell (PPy) tubular structures with the thickness of the PPy layer in the range of 20–40 nm, depending on the concentration of CTAB. Raman and FTIR spectra of the composites are almost identical to those of PPy alone. The electrical conductivities of these composites are 1–2 orders of magnitude higher than those of PPy without MWCNTs. © 2006 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 44: 6449–6457, 2006     

Multiwalled carbon nanotube/polymer nanocomposites: Processing and properties

Nanocomposite materials were prepared with an amorphous poly(styrene‐co‐butyl acrylate) latex as a matrix with multiwalled carbon nanotubes (MWNTs) as fillers. The microstructure of the related films was observed by transmission electron microscopy, which showed that a good dispersion of MWNTs within the matrix was obtained. The linear and nonlinear mechanical behavior and the electrical properties were analyzed. Mechanical characterization showed a mechanical reinforcement effect of the MWNTs with a relatively small decrease of the elongation at break. The composite materials exhibited an elastic behavior with increasing temperature, although the matrix alone became viscous under the same conditions. The electrical conductivity of the composite filled with 3 vol % MWNTs was studied during a tensile test, which highlighted the late damage of the material. © 2005 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 43: 1186–1197, 2005     

Characterization and electrical transport properties of polyaniline and multiwall carbon nanotube composites

Polyaniline/multiwalled carbon nanotube (PANI/MWNT) composites were prepared by in situ polymerization. Scanning electron microscope, X‐ray diffraction, Fourier transform infrared, Uv‐Visible spectroscopy, Fluorescence spectrophotometry were done to characterize the PANI/MWNT composites. Thermal stability was measured by thermogravimetry analysis. The thermal stability of PANI/MWNT composites becomes higher than PANI. Electrical transport properties of different PANI/MWNT composites were investigated in the temperature range 77 ≤ T ≤ 300 K with and without magnetic field up to 1 T. The dc resistivity of PANI/MWNT composites shows different behavior compared to the sample without MWNT. The room temperature dc magnetoconductivity of the samples is negative; however, its sign changes to positive by lowering the temperature, which has been explained by hopping type charge transport. © 2010 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 48: 1767–1775, 2010     

Preparation and properties of natural rubber composites reinforced with pretreated carbon nanotubes

In order to achieve dramatic improvements in the performance of rubber materials, the development of carbon nanotube (CNT)‐reinforced rubber composites was attempted. The CNT/natural rubber (NR) nanocomposite was prepared through solvent mixing on the basis of pretreatment of CNTs. Thermal properties, vulcanization characteristics, and physical and mechanical properties of the CNT/NR nanocomposites were characterized in contrast to the carbon black (CB)/NR composite. Through the addition of the CNTs treated using acid bath followed by ball milling with HRH (hydrated silica, resorcinol, and hexamethylene tetramine) bonding systems, the crystallization melting peak in differential scanning calorimetry (DSC) curves of NR weakened and the curing rate of NR slightly decreased. Meanwhile, the over‐curing reversion of CNT/NR nanocomposites was alleviated. The dispersion of the treated CNTs in the rubber matrix and interfacial bonding between them were rather good. The mechanical properties of the CNT‐reinforced NR showed a considerable increase compared to the neat NR and traditional CB/NR composite. At the same time, the CNT/NR nanocomposites exhibited better rebound resilience and dynamic compression properties. The storage modulus of the CNT/NR nanocomposites greatly exceeds that of neat NR and CB/NR composites under all temperature regions. The thermal stability of NR was also obviously improved with the addition of the treated CNTs. Copyright © 2008 John Wiley & Sons, Ltd.     

Processing and properties of melt spun polylactide–multiwall carbon nanotube fiber composites

This article reports on the fabrication of oriented composite fibers between polylactide (PLA) and multiwall carbon nanotube (MWNT). The fibers were fabricated using a custom‐built melt fiber‐drawing setup. The influence of processing parameters on the final fiber diameter and on the orientation were characterized and optimized. Composite fibers were fabricated at various MWNT contents. Addition of low amounts of MWNT (0.25–1 wt %) to PLA did not have a significant effect on the diameters of the fibers. Observations of the composite morphology under STEM indicated preferential orientation of the MWNTs along the draw direction of the fibers. Increasing amounts of MWNTs was found to increase crystallization kinetics and content. The crystalline content had a direct and profound implication on the mechanical properties with 0.5‐wt % MWNT fibers having the highest crystalline content and also the highest Young's modulus. © 2014 Wiley Periodicals, Inc. J. Polym. Sci., Part B: Polym. Phys. 2014 , 52, 477–484     

Polypropylene/carbon nanotube magnetic composites obtained using carbon nanotubes from sawdust

Magnetic polypropylene (PP) nanocomposites with different loadings (from 0.5 to 20 wt %) of carbon nanotubes with iron (CNT‐Fe) were fabricated using the melt‐mixing method. The carbon nanotubes were synthesized by pyrolysis of sawdust from the furniture industry. The morphological characterization shows homogenous dispersion of the filler in the polymer matrix. The addition of only 0.5 wt % CNT‐Fe already results in ferromagnetic behavior in the diamagnetic polymer matrix. The thermal properties were investigated using thermogravimetric analysis and differential scanning calorimetry. The results show an increase in the maximum degradation, crystallization, and melting temperatures of the nanocomposites compared with neat PP. The nanocomposites showed improvement in terms of mechanical and oxygen permeability properties. A very significant result of the work is the high remnant magnetization and coercivity values of the nanocomposites at room temperature whereas most of the works on similar systems show magnetic properties only at very low temperatures.     

Characterization and electrical properties of polypyrrole/multiwalled carbon nanotube composites synthesized by in situ chemical oxidative polymerization

This study describes the preparation of polypyrrole (PPy)/multiwalled carbon nanotube (MWNT) composites by in situ chemical oxidative polymerization. Various ratios of MWNTs, which served as hard templates, were first dispersed in aqueous solutions with the surfactant cetyltrimethylammonium bromide to form micelle/MWNT templates and overcome the difficulty of MWNTs dispersing into insoluble solutions of pyrrole monomer, and PPy was then synthesized via in situ chemical oxidative polymerization on the surface of the templates. Raman spectroscopy, Fourier transform infrared (FTIR), field‐emission scanning electron microscopy (FESEM), and high‐resolution transmission electron microscopy (HRTEM) were used to characterize the structure and morphology of the fabricated composites. Structural analysis using FESEM and HRTEM showed that the PPy/MWNT composites were core (MWNT)–shell (PPy) tubular structures. Raman and FTIR spectra of the composites were almost identical to those of PPy, supporting the idea that MWNTs served as the core in the formation of a coaxial nanostructure for the composites. The conductivities of these PPy/MWNT composites were about 150% higher than those of PPy without MWNTs. © 2006 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 44: 1413–1418, 2006     

Effects of processing conditions on rheological,thermal, and electrical properties of multiwall carbon nanotube/epoxy resin composites

We report on the effect of processing conditions on rheology, thermal and electrical properties of nanocomposites containing 0.02–0.3 wt % multiwall carbon nanotubes in an epoxy resin. The influence of the sonication, the surface functionalization during mixing, as well as the application of external magnetic field (EMF) throughout the curing process was examined. Rheological tests combined with optical microscopy visualization are proved as a very useful methodology to determine the optimal processing conditions for the preparation of the nanocomposites. The Raman spectra provide evidence for more pronounced effect on the functionalized with hardener compositions, particularly by curing upon application of EMF. Different chain morphology of CNTs is created depending of the preparation conditions, which induced different effects on the thermal and electrical properties of the nanocomposites. The thermal degradation peak is significantly shifted towards higher temperatures by increasing the nanotube content, this confirming that even the small amount of carbon nanotubes produces a strong barrier effect for the volatile products during the degradation. The ac conductivity measurements revealed lower values of the percolation threshold (pc) in the range of 0.03–0.05 wt %. CNTs for the nanocomposites produced by preliminary dispersing of nanotubes in the epoxy resin, compared to those prepared by preliminary functionalization of the nanotubes in the amine hardener. This is attributed to the higher viscosity and stronger interfacial interactions of the amine hardener/CNT dispersion which restricts the reorganization of the nanotubes. The application of the EMF does not influence the pc value but the dc conductivity values (σ_dc) of the nanocomposites increased at about one order of magnitude due to the development of the aforementioned chain structure. © 2011 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys, 2011     

Effect of carbon nanofibers on mechanical and electrical behaviors of acrylonitrile‐butadiene rubber composites

Recently, carbon nanofibers have become an innovative reinforcing filler that has drawn increased attention from researchers. In this work, the reinforcement of acrylonitrile butadiene rubber (NBR) with carbon nanofibers (CNFs) was studied to determine the potential of carbon nanofibers as reinforcing filler in rubber technology. Furthermore, the performance of NBR compounds filled with carbon nanofibers was compared with the composites containing carbon black characterized by spherical particle type. Filler dispersion in elastomer matrix plays an essential role in polymer reinforcement, so we also analyzed the influence of dispersing agents on the performance of NBR composites. We applied several types of dispersing agents: anionic, cationic, nonionic, and ionic liquids. The fillers were characterized by dibutylphtalate absorption analysis, aggregate size, and rheological properties of filler suspensions. The vulcanization kinetics of rubber compounds, crosslink density, mechanical properties, hysteresis, and conductive properties of vulcanizates were also investigated. Moreover, scanning electron microscopy images were used to determine the filler dispersion in the elastomer matrix. The incorporation of the carbon nanofibers has a superior influence on the tensile strength of NBR compared with the samples containing carbon black. It was observed that addition of studied dispersing agents affected the performance of NBR/CNF and NBR/carbon black materials. Especially, the application of nonylphenyl poly(ethylene glycol) ether and 1‐butyl‐3‐methylimidazolium tetrafluoroborate contributed to enhanced mechanical properties and electrical conductivity of NBR/CNF composites.     

Influence of multiwall carbon nanotubes on morphology and electrical conductivity of PP/ABS blends

Polypropylene (PP) and acrylonitrile‐butadiene‐styrene (ABS) blends with multiwall carbon nanotubes (MWNT) were prepared by melt mixing. PP/ABS blends without MWNT revealed coarse co continuous structures on varying the ABS content from 40 to 70 wt %. Bulk electrical conductivity of the blends showed lower percolation threshold (0.4–0.5 wt %) in the 45/55 co continuous blends whereas the percolation threshold was between 2 and 3 wt % in matrix‐particle dispersed morphology of 80/20 blends. Interestingly, droplet size was observed to decrease with addition of MWNT above percolation threshold in 80/20 blends. Further, the bulk electrical conductivity was found to be dependent on the melt flow index of PP. The non‐polar or weakly polar nature of blends constituents resulted in the temperature independent dielectric constant, dielectric loss, and DC electrical conductivity. Rheological analysis revealed the formation of 3D network‐like structure in 80/20 PP/ABS blends at 3 wt % MWNT. An attempt was made to understand the relationship between rheology, morphology, and electrical conductivity of these blends. © 2008 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 46: 2286–2295, 2008     

Poly(vinyltriethoxysilane) modified MWCNT/polyimide nanocomposites—Preparation,morphological, mechanical,and electrical properties

Multi‐walled carbon nanotube (MWCNT) modified by vinyltriethoxysilane (VTES) via free radical reaction has been prepared (poly (vinyltriethoxysilane) modified MWCNTs, PVTES‐MWCNT). Precursor of polyimide, polyamic acid has been synthesized by reacting 4,4′‐oxydianiline with 3,3′,4,4′‐benzophenone tetracarboxylic dianhydride. PVTES‐MWCNT were then mixed with polyamic acid and heated to 300 °C to form CNT/polyimide composite. During the imidization processes, the silanes on CNT surface reacted with each other and may be connected together by covalent bond (Si? O? Si). The PVTES‐MWCNT was analyzed by Fourier transform infrared and X‐ray photoelectron spectroscopy. The PVTES‐MWCNT/polyimide composites were analyzed by CP/MAS solid state ²⁹Si nuclear magnetic resonance (NMR) spectroscopy. Morphological properties of the PVTES‐MWCNT/polyimide composites were investigated by scanning electron microscope and transmission electron microscope. Electrical conductivity increased dramatically comparing to the unmodified MWCNT/polyimide composites. Mechanical properties of nanocomposite were enhanced significantly by PVTES‐MWCNT. © 2007 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 46: 803–816, 2008     

Investigation of polycarbonate/acrylonitrile butadiene styrene/multiwall carbon nanotube nanocomposites under impact loading

In this study, the effect of polycarbonate (PC)/acrylonitrile butadiene styrene (ABS)‐reinforced multiwall carbon nanotube (MWCNT) nanocomposites under a high‐velocity impact was investigated. PC/ABS (70/30 w/w)/MWCNT nanocomposites containing 1, 2, and 4 wt% were used to manufacture samples for this study. The samples were fabricated in sheet form with 100 × 100 mm dimensions and tested by gas gun for high‐velocity impact tests. The experimental results indicate that the energy absorption, limit velocity, and tensile modulus of the nanocomposite samples increased by approximately 121%, 52%, and 103% for the PC/ABS (70/30 w/w)/2 wt% MWCNT samples respectively. These results were confirmed by a transmission electron microscopy analysis test that was conducted for the state of dispersion of MWCNTs in the nanocomposite samples. The transmission electron microscopy results show that the best morphological structure of carbon nanotube at the interface of PC and ABS is that for the nanocomposite containing 2 wt% MWCNTs, which led to improved interface of the nanocomposites and higher mechanical properties. Copyright © 2016 John Wiley & Sons, Ltd.     

Significant enhancement of electrical and thermal conductivities of polyethylene carbon nanotube composites by the addition of a low amount of silver nanoparticles

Electrically and thermally conductive high‐density polyethylene composites filled with hybrid fillers, multiwall carbon nanotubes (MWCNTs) and silver nanoparticles (Ag‐NPs), have been prepared in the melt state. The investigation of their electrical and thermal conductivities while comparing with high‐density polyethylene/MWCNT binary composites shows that the addition of only 3 vol% of Ag‐NPs does not reduce the electrical percolation threshold (P_c) that remains as low as 0.40 vol% of MWCNTs but leads to an increase in the maximum dc electrical conductivity of PE/MWCNT composites by two orders of magnitudes. Moreover, the association of both Ag‐NPs and carbon nanotube particles improved our composite's thermal conductivity. Copyright © 2014 John Wiley & Sons, Ltd.     

Aspect ratio effects of multi‐walled carbon nanotubes on electrical,mechanical, and thermal properties of polycarbonate/MWCNT composites

Two multi‐walled carbon nanotubes (MWCNTs) having relatively high aspect ratios of 313 and 474 with approximately the same diameter were melt mixed with polycarbonate (PC) in a twin‐screw conical micro compounder. The effects of aspect ratio on the electrical, mechanical, and thermal properties of the PC/MWCNT composites were investigated. Electrical conductivities and storage moduli of the filled samples are found to be independent of the starting aspect ratio for these high aspect ratio tubes; although the conductivities and storage moduli are still significantly higher than values of composites made with nanotubes having more commercially common aspect ratios of ～100. Transmission electron microscopy results suggest that melt‐mixing reduces these longer nanotubes to the same length, but still approximately two times longer than the length of commercially common aspect ratio tubes after melt‐mixing. Molecular weight measurements show that during melt‐mixing the longer nanotubes significantly degrade the molecular weight of the polymer as compared to very similar nanotubes with aspect ratio ～100. Because of the molecular weight reduction glass transition temperatures predictably show a large decrease with increasing nanotube concentration. © 2013 Wiley Periodicals, Inc. J. Polym. Sci., Part B: Polym. Phys. 2014 , 52, 73–83     

Vibrational Spectroscopic and Mechanical Investigation of Carbon Nanotube-Reinforced Styrene-Butadiene Rubbers

This paper reports investigations carried out on elastomeric matrices based on a styrene-butadiene copolymer filled with multiwall carbon nanotubes. Stress-strain measurements of the composites demonstrate that carbon nanotubes bring significantly improvements in the mechanical properties with regard to the pure polymer. Raman spectroscopy, which is one of the most extensively employed methods for the characterization of carbon materials, has been applied for the analysis of the dependence of the Raman spectra on the nanotube content and on application of an uniaxial deformation. The results reveal a negligible stress transfer suggesting a weak interface between the tubes and the polymer chains.     

Molecular motion,morphology, and thermal properties of multiwall carbon nanotube/polysilsesquioxane composite

Diglycidyl ether of bisphenol A (DGEBA)‐bridged polyorganosiloxane precursors have been prepared successfully by reacting diglycidyl ether of bisphenol A epoxy resin with 3‐aminopropyltriethoxysilane. Acid‐modified and unmodified multiwalled carbon nanotube (MWCNT) were dispersed in the diglycidyl ether of bisphenol A‐bridged polyorganosiloxane precursors and cured to prepare the carbon nanotube/diglycidyl ether of bisphenol A‐bridged polysilsesquioxane (MWCNT/DGEBA‐PSSQ) composites. The molecular motion of MWCNT/DGEBA‐PSSQ nanocomposites was studied by high‐resolution solid‐state ¹³C NMR. Acid‐modification can improve the affinity between MWCNT and the polymer matrix. The molecular motion of the DGEBA‐PSSQ decreased with acid‐modified MWCNT content. However, when unmodified MWCNT was used, the molecular motion of the DGEBA‐PSSQ was increased. SEM and TEM microphotographs confirm that acid‐modified MWCNT exhibits better dispersion than unmodified MWCNT in DGBEA‐PSSQ. The dynamic mechanical properties of acid‐modified MWCNT/DGBEA‐PSSQ composites are more favorable than those of unmodified MWCNT. T_g of the DGEBA‐PSSQ decreased from 174.0 °C (neat DGEBA‐PSSQ) to 159.0 °C (1 wt % unmodified MWCNT) and 156.0 °C (1 wt % acid‐modified MWCNT). The storage modulus (at 30 °C) of the DGEBA‐PSSQ increased from 1.23 × 10⁹ Pa (neat DGEBA‐PSSQ) to 1.65 × 10⁹ Pa (1 wt % acid‐modified MWCNT). However, when unmodified MWCNT was used, the storage modulus of the DGEBA‐PSSQ decreased to 6.88 × 10⁸ Pa (1 wt % unmodified MWCNT). At high temperature, above 150 °C, storage modulus of nanocomposites was higher than that of neat polymer system. © 2008 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 46: 472–482, 2008     

Combined electrical and rheological properties of shear induced multiwall carbon nanotube agglomerates in epoxy suspensions

In this work the rheological and electrical properties of semi-dilute carbon nanotube (CNT)–epoxy suspensions have been discussed. The suspensions are produced using two types of industrially available CNTs (Nanocyl 3150 and 7000) and using two different dispersion techniques, namely 3-roll milling and sonication. In-situ optical microscopic analysis and electrical conductivity measurements have been conducted. It is shown that despite using CNTs with similar aspect ratios, the dispersability of the raw material and the time stability of the suspensions are quite different. Additionally, viscosity measurements are used to evaluate the initial dispersion quality and time stability.     

Nucleation ability of multiwall carbon nanotubes in polypropylene composites

The nonisothermal crystallization of multiwall carbon nanotube (MWNT)/isotactic polypropylene (iPP) nanocomposites was investigated. The results derived from the differential scanning calorimetry curves (onset temperature, melting point, supercooling, peak temperature, half‐time of crystallization, and enthalpy of crystallization) were compared with those of neat iPP. The data were also processed according to Ozawa's theory and Dobreva's approach. These results and X‐ray diffraction data showed that the MWNTs acted as α‐nucleating agents in iPP. Accordingly, MWNT/iPP was significantly different from neat iPP: A fibrillar morphology was observed instead of the usual spherulites. © 2003 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 41: 520–527, 2003     

Highly enhanced electrical and mechanical properties of methyl methacrylate modified natural rubber filled with multiwalled carbon nanotubes

Developing conductive networks in a polymer matrix with a low percolation threshold and excellent mechanical properties is desired for soft electronics applications. In this work, natural rubber (NR) functionalized with poly(methyl methacrylate) (PMMA) was prepared for strong interfacial interactions with multiwalled carbon nanotubes (MWCNT), resulting in excellent performance of the natural rubber nanocomposites. The MWCNT and methyl methacrylate functional groups gave good filler dispersion, conductivity and tensile properties. The filler network in the matrix was studied with microscopy and from its non-linear viscoelasticity. The Maier-Göritze approach revealed that MWCNT network formation was favored in the NR functionalized with PMMA, with reduced electrical and mechanical percolation thresholds. The obvious improvement in physical performance of MWCNT/methyl methacrylate functionalized natural rubber nanocomposites was caused by interfacial interactions and reduced filler agglomeration in the NR matrix. The modification of NR with poly(methyl methacrylate) and MWCNT filler was demonstrated as an effective pathway to enhance the mechanical and electrical properties of natural rubber nanocomposites.