Phenylene vinylene‐based electroluminescent polymers with electron transport block in the main chain

We report a new route for the design of soluble phenylene vinylene (PV) based electroluminescent polymers bearing electron‐deficient oxadizole (OXD) and triazole (TZ) moieties in the main chains with the aryloxy linkage. Both series of the PV‐based polymers were prepared by Wittig reaction. By properly adjusting the OXD and/or TZ content through copolymerization, we can achieve an enhanced balance of hole‐ and electron injections, such that the device efficiency is significantly improved. Light‐emitting diodes fabricated from P1, P2, P3, P4, P5, P6, and P7 with the configuration of Indium–Tin Oxide (ITO)/Poly (styrene sulfonic acid) doped poly (ethylenedioxythiophene) (PEDOT)/polymer/Ca/Al, emit bright green light with the maximum peak around 500 nm. For the device using the optimal polymer (P4) as emitting layer, a maximum brightness of 1300 cd/m² at 20 V and a maximum luminance efficiency of 0.325 cd/A can be obtained. © 2006 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 44: 3469–3478, 2006     

Synthesis and optical properties of light‐emitting π‐conjugated polymers containing biphenyl and dithienosilole

Copolymers containing oligo(phenylene vinylene) (2.5), fluorene, and 4,4‐dihexyldithienosilole (DTS) units were synthesized and characterized. The π‐conjugated monomers were joined with the palladium(0)‐catalyzed Suzuki–Miyaura coupling reaction, thus forming either biphenyl– or phenyl–thiophene linkages. These polymers were photoluminescent, with the fluorescent quantum efficiency between 54 and 63% and with λ_max for fluorescence at ～448 nm in tetrahydrofuran. The presence of 5% DTS in the copolymers had little influence on the optical absorption and emission wavelengths. Double‐layer light‐emitting‐diode devices using these polymers as emissive layers had low turn‐on voltages (3.5–4 V) and moderate external quantum efficiencies (0.14–0.30%). The results show that DTS plays a positive role in improving the charge‐injection characteristics of poly(phenylene vinylene) materials. © 2007 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 45: 2048–2058     

Fluorene‐based alternating polymers containing electron‐withdrawing bithiazole units: Preparation and device applications

We report here the synthesis via Suzuki polymerization of two novel alternating polymers containing 9,9‐dioctylfluorene and electron‐withdrawing 4,4′‐dihexyl‐2,2′‐bithiazole moieties, poly[(4,4′‐dihexyl‐2,2′‐bithiazole‐5,5′‐diyl)‐alt‐(9,9‐dioctylfluorene‐2,7‐diyl)] (PHBTzF) and poly[(5,5′‐bis(2″‐thienyl)‐4,4′‐dihexyl‐2,2′‐bithiazole‐5″,5″‐diyl)‐alt‐(9,9‐dioctylfluorene‐2,7‐diyl)] (PTHBTzTF), and their application to electronic devices. The ultraviolet–visible absorption maxima of films of PHBTzF and PTHBTzTF were 413 and 471 nm, respectively, and the photoluminescence maxima were 513 and 590 nm, respectively. Cyclic voltammetry experiment showed an improvement in the n‐doping stability of the polymers and a reduction of their lowest unoccupied molecular orbital energy levels as a result of bithiazole in the polymers' main chain. The highest occupied molecular orbital energy levels of the polymers were ?5.85 eV for PHBTzF and ?5.53 eV for PTHBTzTF. Conventional polymeric light‐emitting‐diode devices were fabricated in the ITO/PEDOT:PSS/polymer/Ca/Al configuration [where ITO is indium tin oxide and PEDOT:PSS is poly(3,4‐ethylenedioxythiophene) doped with poly(styrenesulfonic acid)] with the two polymers as emitting layers. The PHBTzF device exhibited a maximum luminance of 210 cd/m² and a turn‐on voltage of 9.4 V, whereas the PTHBTzTF device exhibited a maximum luminance of 1840 cd/m² and a turn‐on voltage of 5.4 V. In addition, a preliminary organic solar‐cell device with the ITO/PEDOT:PSS/(PTHBTzTF + C₆₀)/Ca/Al configuration (where C₆₀ is fullerene) was also fabricated. Under 100 mW/cm² of air mass 1.5 white‐light illumination, the device produced an open‐circuit voltage of 0.76 V and a short‐circuit current of 1.70 mA/cm². The fill factor of the device was 0.40, and the power conversion efficiency was 0.52%. © 2005 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 43: 1845–1857, 2005     

Synthesis and electroluminescent properties of polyfluorene‐based conjugated polymers containing bipolar groups

A bipolar dibromo monomer, bis‐(4‐bromophenyl)[4‐(3,5‐diphenyl‐1,2,4‐ triazole‐4‐yl)‐phenyl]amine ( 9 ), containing electro‐rich triphenylamine and electro‐deficient 1,2,4‐triazole moieties was newly synthesized and characterized. Two fluorescent fluorene‐based conjugated copolymers ( TPAF , TPABTF ) were prepared via facile Suzuki coupling from the dibromo bipolar monomer, 4,7‐dibromo‐2,1,3‐benzothiadiazole ( BTDZ ), and 9,9‐dioctylfluorene. They were characterized by molecular weight determination, IR, NMR, DSC, TGA, solubility, absorption and photoluminescence spectra, and cyclic voltammetry. The polymers showed good solubility in common organic solvents such as dichloromethane, chloroform, tetrahydrofuran, and dichlorobenzene at room temperature. They had glass transition temperatures (T_g) higher than 135 °C and 5% degradation temperatures in nitrogen atmosphere were higher than 428 °C. Single layer polymer light‐emitting diodes (PLED) of ITO/PEDOT:PSS/polymer/metal showed a blue emission at 444 nm and Commission Internationale de I'Eclairage (CIE) 1931 color coordinates of (0.16, 0.13) for TPAF . The device using TPABTF as emissive material showed electroluminescence at 542 nm with CIE1931 of (0.345, 0.625), low turn‐on voltage of 5 V, a maximum electroluminance of 696 cd/m², and a peak efficiency of 2.02 cd/A. © 2009 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 47: 6231–6245, 2009     

Synthesis and characterization of highly stable blue‐light‐emitting hyperbranched conjugated polymers

Polyfluorene homopolymer ( P1 ) and its carbazole derivatives ( P2 – P4 ) have been prepared with good yield by Suzuki coupling polymerization. P2 is an alternating copolymer based on fluorene and carbazole; P3 is a hyperbranched polymer with carbazole derivative as the core and polyfluorene as the long arms; P4 is a hyperbranched polymer with carbazole derivative as the core and the alternating fluorene and carbazole as the long arms. These polymers show highly thermal stability, and their structures and physical properties are studied using gel permeation chromatography, ¹H NMR, ¹³C NMR, elemental analysis, Fourier transform infrared spectroscopy, thermogravimetry, UV–vis absorption, photoluminescence, and cyclic voltammetry (CV). The influence of the incorporation of carbazole and the hyperbranched structures on the thermal, electrochemical, and electroluminescent properties has been investigated. Both carbazole addition and the hyperbranched structure increase the thermal and photoluminescent stability. The CV shows an increase of the HOMO energy levels for the derivatives, compared with polyfluorene homopolymer ( P1 ). The EL devices fabricated by these polymers exhibit pure blue‐light‐emitting with negligible low‐energy emission bands, indicating that the hyperbranched structure has a strong effect on the PLED characteristics. The results imply that incorporating carbazole into polyfluorene to form a hyperbranched structure is an efficient way to obtain highly stable blue‐light‐emitting conjugated polymers, and it is possible to adjust the property of light‐emitting polymers by the amount of carbazole derivative incorporated into the polymers. © 2007 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 46: 790–802, 2008     

3,6‐linked 9‐alkyl‐9H‐carbazole main‐chain polymers: Preparation and properties

An investigation into the preparation of poly(9‐alkyl‐9H‐carbazole‐3,6‐diyl)s with palladium catalyzed cross‐coupling reactions of 3‐halo‐6‐halomagnesio‐9‐alkyl‐9H‐carbazoles, generated in situ from their corresponding 3,6‐diiodo‐ and 3,6‐dibromo‐derivatives was undertaken. Monomers with a range of alkyl group substituents with different steric requirements were investigated and their effects on the polymerization were studied. The effects of the nature of halogen substituents on the polymerization reaction were also investigated. Structural analysis of the polymers revealed exclusive 3,6‐linkage between consecutive carbazole repeat units on the polymer chains. The physical properties of these polymers were investigated with spectroscopic, thermal gravimetric analysis, and electrochemical studies. © 2004 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 42: 6041–6051, 2004     

Conjugated and partially conjugated 2,5‐diphenylthiophene‐containing light‐emitting copolymers in polymeric light‐emitting diode (PLED) device fabrications

To study the effect of nonconjugation on polymeric and photophysical properties of thiophene‐containing polymers, new light‐emitting copolymers comprising either alternate 2,5‐diphenylthiophene and vinylene or alternate 2,5‐diphenylthiophene and aliphatic ether segments were synthesized. Both copolymers contained 2,5‐diphenylthiophene as the major chromophore and emitted a sky bluish fluorescence in dilute solution (10^?2 mg/mL). With a rigid and planarity structure and the concomitant crystallinity, the former copolymer (fully conjugated) possessed a higher quantum efficiency, a higher glass‐transition temperature, and a better thermal stability. In contrast, the latter copolymer (conjugated–nonconjugated) had better solubility and provided enhanced photophysical properties for the fabricated polymeric light‐emitting diode (PLED) device: at 15 V, the maximum current and brightness were 110 mA/cm² and 4289 cd/m², respectively, and the electroluminescence efficiency remained constant at approximately 4.9 cd/A in a voltage range of 8 to 14 V. The existence of intramolecular/intermolecular aggregates in the latter copolymer was corroborated from the the UV–vis and photoluminescence spectra of its solutions. With an increase in solution concentration, the shape and λ_max of the photoluminescence spectrum were redshifted. In a solution with a concentration as high as 10 mg/mL, the redshift was so drastic that the photoluminescence spectrum was nearly identical to that of a solid‐film. © 2004 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 42: 6061–6070, 2004     

Synthesis and electroluminescent properties of fluorene‐based copolymers containing electron‐withdrawing thiazole derivatives

We synthesized two fluorene‐based copolymers poly[(2,5‐bis(4‐hexylthiophen‐2‐yl)thiazolo[5,4‐day]thiazole‐5,5′‐diyl)‐alt‐(9,9′‐dioctylfluorene‐2,7‐diyl)] ( PF‐TTZT), and poly[(5,5′‐bis(4‐hexylthiophen‐2‐yl)‐2,2′‐bithiazole‐5,5′‐diyl)‐alt‐(9,9′‐dioctylfluorene‐2,7‐diyl)] (PF‐TBTT), which contain the electron‐withdrawing moieties, thiazolothiazole, and bithiazole, respectively. Through electrochemical studies, we found that these two polymers exhibit stable reversible oxidation and reduction behaviors. Moreover, the highest occupied molecular orbital (HOMO) and lowest unoccupied molecular orbital (LUMO) energy levels of PF‐TBTT are lower than those of PF‐TTZT, and the bandgap of PF‐TBTT is smaller than that of PF‐TTZT. Thus the bithiazole moiety in PF‐TBTT is more electron‐withdrawing than the thiazolothiazole moiety in PF‐TTZT. Light‐emitting devices with indium tin oxide (ITO)/poly(3,4‐ethylene dioxythiophene):poly(styrenesulfonate)(PEDOT)/polymer/bis(2‐methyl‐8‐quinolinato)‐4‐phenylphenolate aluminum (BAlq)/LiF/Al configurations were fabricated. The performance of the PF‐TBTT device was found to be almost three times better than that of the PF‐TTZT device, which is because electron injection from the cathode to PF‐TBTT is much easier than for PF‐TTZT. We also investigated the planarity and frontier orbitals of the electron donor‐acceptor (D‐A) moieties with computational calculations using ab initio Hartree–Fock with the split‐valence 6‐31G* basis set. These calculations show that TBTT has a more nonplanar structure than TTZT and that the bithiazole moiety is more electron‐withdrawing than thiazolothiazole. These calculations are in good agreement with the experimental results. © Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 46: 7148–7161, 2008     

Synthesis and photovoltaic properties of conjugated side chains polymers with different electron‐withdrawing and donating end groups

A series of novel low band gap polymers containing conjugated side chains with 4,7‐dithien‐5‐yl‐2,1,3‐benzodiathiazole and different electron‐withdrawing end groups of aldehyde ( PT‐DTBTCHO ), 2‐ethylhexyl cyanoacetate ( PT‐DTBTCN ), 1,3‐diethyl‐2‐thiobarbituric acid ( PT‐DTBTDT ), and electron‐donating end group of 2‐methylthiophene ( PT‐DTBTMT ) have been designed and synthesized. All polymers exhibit good solubility in common organic solvents, film‐forming ability, and thermal stability. These conjugated polymers show the broad ultraviolet‐visible absorption and the narrow optical band gaps in the range of 1.65–1.90 eV. Through changing the end group of conjugated side chains, the photophysical properties and energy levels of the polymers were tuned effectively. Bulk heterojunction solar cells based on the blend of these polymers and (6,6)‐phenyl‐C₆₁‐butyric acid methyl ester (PC₆₁BM) reached the best power conversion efficiency (PCE) of 2.72%. © 2012 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2012     

Conjugated polymers containing electron‐transporting,hole‐transporting,and light‐emitting units in the polymer main chain

Conjugated polymers containing electron‐transporting, hole‐transporting, and blue light‐emitting units were synthesized by Suzuki polycondensation. These copolymers exhibited excellent thermal and optical stability. Optical investigation indicated that the incorporation of the spirobifluorene units in the polymer main chain could markedly increase the effective conjugation length of polymers. Electrochemical studies showed that the incorporation of spirobifluorene unit could raise the electrochemical stability and improve the electron‐ and hole‐injecting abilities. The electroluminescent results also showed that the introducing of spirobifluorene units could significantly improve the device performance. © 2008 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 46: 1349–1356, 2008     

Synthesis and electrochemical and electroluminescent properties of N‐phenylcarbazole‐substituted poly(p‐phenylenevinylene)

An N‐phenylcarbazole‐containing poly(p‐phenylenevinylene) (PPV), poly[(2‐(4′‐carbazol‐9‐yl‐phenyl)‐5‐octyloxy‐1,4‐phenylenevinylene)‐alt‐(2‐(2′‐ethylhexyloxy)‐5‐methoxy‐1,4‐phenylenevinylene)] (Cz‐PPV), was synthesized, and its optical, electrochemical, and electroluminescent properties were studied. The molecular structures of the key intermediates, the carbazole‐containing boronic ester and the dialdehyde monomer, were crystallographically characterized. The polymer was soluble in common organic solvents and exhibited good thermal stability with a 5% weight loss at temperatures above 420 °C in nitrogen. A cyclic voltammogram showed the oxidation peak potentials of both the pendant carbazole group and the PPV main chain, indicating that the hole‐injection ability of the polymer would be improved by the introduction of the carbazole‐functional group. A single‐layer light‐emitting diode (LED) with a simple configuration of indium tin oxide (ITO)/Cz‐PPV (80 nm)/Ca/Al exhibited a bright yellow emission with a brightness of 1560 cd/m² at a bias of 11 V and a current density of 565 mA/cm². A double‐layer LED device with the configuration of ITO/poly(3,4‐ethylenedioxy‐2,5‐thiophene):poly (styrenesulfonic acid) (60 nm)/Cz‐PPV (80 nm)/Ca/Al gave a low turn‐on voltage at 3 V and a maximum brightness of 6600 cd/m² at a bias of 8 V. The maximum electroluminescent efficiency corresponding to the double‐layer device was 1.15 cd/A, 0.42 lm/W, and 0.5%. The desired electroluminescence results demonstrated that the incorporation of hole‐transporting functional groups into the PPVs was effective for enhancing the electroluminescent performance. © 2005 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 43: 5765–5773, 2005     

Improved EL efficiency of fluorene‐thieno[3,2‐b]thiophene‐based conjugated copolymers with hole‐transporting or electron‐transporting units in the main chain

New electroluminescent polymers (poly(9,9′‐dioctylfluorene‐co‐thieno[3,2‐b]thiophene‐co‐benzo[2,3,5]thiadiazole) ( P1) and poly(9,9′‐dioctylfluorene‐co‐thieno[3,2‐b]thiophene‐co‐benzo[2,3,5]thiadiazole‐co‐[4‐(2‐ethylhexyloxyl)phenyl]diphenylamine ( P2) ) possess hole‐transporting or electron‐transporting units or both in the main chains. Electron‐deficient benzothiadiazole and electron‐rich triphenylamine moieties were incorporated into the polymer backbone to improve the electron‐transporting and hole‐transporting characteristics, respectively. P1 and P2 show greater solubility than poly(9,9′‐dioctylfluorene‐co‐thieno[3,2‐b]thiophene ( PFTT ), without sacrificing their good thermal stability. Moreover, owing to the incorporation of the electron‐deficient benzothiadiazole unit, P1 and P2 exhibit remarkably lower LUMO levels than PFTT , and thus, it should facilitate the electron injection into the polymer layer from the cathode electrode. Consequently, because of the balance of charge mobility, LED devices based on P1 and P2 exhibit greater brightness and efficiency (up to 3000 cd/m² and 1.35 cd/A) than devices that use the pristine PFTT . © 2005 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 44: 243–253, 2006     

Synthesis and photovoltaic properties of two‐dimensional D‐A copolymers with conjugated side chains

Four novel two‐dimensional (2D) donor–acceptor (D‐A) type copolymers with different conjugated side chains, P1 , P2 , P3 , and P4 (see Fig. 1 ), are designed and synthesized for the application as donor materials in polymer solar cells (PSCs). To the best of our knowledge, there were few reports to systematically study such 2D polymers with D‐A type main chains in this area. The optical energy band gaps are about 2.0 eV for P1 – P3 and 1.67 eV for P4 . PSC devices using P1 – P4 as donor and [6,6]‐phenyl‐C₆₁‐butyric acid methyl ester as acceptor in a weight ratio of 1:3 were fabricated and characterized to investigate the photovoltaic properties of the polymers. Under AM 1.5 G, 100 mA/cm² illumination, a high open‐circuit voltage (V_oc) of 0.9 V was recorded for P3 ‐based device due to its low HOMO level, and moderate fill factor was obtained with the best value of 58.6% for P4 ‐based device, which may mainly be the result of the high hole mobility of the polymers (up to 1.82 × 10^?3 cm²/V s). © 2011 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2011     

Triarylamine N‐functionalized 3,6‐linked carbazole main chain polymers and copolymers: Preparation and physical properties

The preparation of triarylamine N‐functionalized 3,6‐linked carbazole homopolymers as well as alternating copolymers with 2,5‐diphenyl‐[1,3,4]oxadiazole and benzo[1,2,5]thiadiazole was undertaken using Suzuki cross‐coupling polymerization procedures associating 3,6‐bis(4,4,5,5‐tetramethyl‐[1,3,2]dioxaborolan‐2‐yl)‐9‐(bis[4‐(2‐butyl‐octyloxy)‐phenyl]‐amino‐phen‐4‐yl)‐carbazole and, respectively, 3,6‐dibromo‐9‐(bis[4‐(2‐butyl‐octyloxy)‐phenyl]‐amino‐phen‐4‐yl)‐carbazole, 2,5‐bis(4‐bromo‐phenyl)‐[1, 3,4]oxadiazole, and 4,7‐dibromo‐benzo[1,2,5]thiadiazole. Both the carbazole homopolymer and alternating copolymer with 2,5‐diphenyl‐[1,3,4]oxadiazole were found as wideband gap materials emitting in the blue part of the electromagnetic spectrum while the carbazole alternating copolymer with 4,7‐benzo[1,2,5]thiadiazole had a narrower band gap and emitted in the orange part of the electromagnetic spectrum. The new polymers are thermally stable up to 300 °C. A discussion of the electrochemical and optical properties of the new polymers is presented. © 2007 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 45: 5957–5967, 2007.     

Alkyl side chain driven tunable red–yellow–green emission: Investigation on the new π‐conjugated polymers comprising of 2,7‐carbazole unit and 2,1,3‐benzo‐thiadiazole units with different side chains

Four new soluble polymers containing a 2,7‐carbazole unit and a 2,1,3‐benzothiadiazole unit in the main chain were synthesized by Suzuki polycondensation. Variation of the substituent groups (R) at 5‐position of 2,1,3‐benzothiadiazole unit resulted in different color emission of the copolymers. Thus, when R was ? CH₃ (or ? H), the polymer showed yellow–green (or red) emission; whereas the polymers showed the emission from green to yellow–green, when R was ? CH₂(CH₂)₅CH₃ or ? CH₂OCH(CH₃)₂. To investigate the nature of the color change, a Gaussian 03 program was used for estimation of the dihedral angles between a 5‐R‐2,1,3‐benzothiadiazole unit and a 2,7‐carbazole unit. The results showed that the different substituents at 5‐position of 2,1,3‐benzothiadiazole brought about different the dihedral angles, which gave the different conjugation levels to the polymers. Hence, the tunablity of emission color may be attributed to the different conjugation levels between 2,7‐carbazole units and 5‐R‐2,1,3‐benzothiadiazole units induced by simply changing substituent groups at 5‐position of benzothiadiazole unit. Electrochemically, the copolymers exhibited a higher oxidation potential as well as the reversible reduction behavior bearing from 2,1,3‐benzothiadiazole unit. To investigate the electroluminescent properties of the polymers, the nonoptimized devices were fabricated and the results showed that the electroluminescent emission wavelength was basically similar to that of the photoluminescent. All polymers showed good thermal stability with 5 wt % loss temperature of more than 296 °C. © 2008 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 46: 1376–1387, 2008     

Synthesis,photophysics, and electroluminescent performance of stable blue‐light‐emitting copoly(9,9‐diarylfluorene)s

A series of fluorene derivatives containing nonsymmetric and bulky aromatic groups at C‐9 position were synthesized and used for the preparation of blue‐light‐emitting copolyfluorenes ( P1 – P4 ) by the Suzuki coupling polycondensation. The copolymers were characterized by molecular weight determination, elemental analysis, differential scanning calorimeter, thermogravimetric analysis, absorption and emission spectroscopy, cyclic voltammetry, and differential pulse voltammetry. Their decomposition temperatures and glass transition temperatures are 423–441 °C and >120 °C, respectively. In film state, the copolyfluorenes exhibit blue photoluminescence at 425–450 nm, which remains almost unchanged after annealing at 200 °C in air for 60 min. Polymer light‐emitting diodes [ITO/PEDOT:PSS/ P1 – P4 /Ca(50 nm)/Al(100 nm)] show stable blue‐light emission under device operation with the CIE co‐ordinates being between (0.16, 0.07) and (0.17, 0.09). The light‐emitting diodes devices from P1 and P3 containing electron‐deficient oxadiazole units display enhanced performance, with the maximum brightness and maximum current efficiency being (4510 cd/m² and 2.40 cd/A) and (2930 cd/m², 1.19 cd/A), respectively. © 2009 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 47: 2821–2834, 2009     

Synthesis and characterization of color‐stable electroluminescent polymers: Poly(dinaphtho[1,2‐a:1′,2′‐g]‐s‐indacene)s

Two new stepladder conjugated polymers, that is, poly(7,7,15,15‐tetraoctyldinaphtho[1,2‐a:1′,2′‐g]‐s‐indacene) (PONSI) and poly(7,7,15,15‐tetra(4‐octylphenyl)dinaphtho[1,2‐a:1′,2′‐g]‐s‐indacene) (PANSI) with alkyl and aryl substituents, respectively, have been synthesized and characterized. In comparison with poly(indenofluorene)s, both polymers have extended conjugation at the direction perpendicular to the polymer backbone because of the introduction of naphthalene moieties. The emission color of the polymers in film state is strongly dependent on the substituents. While PONSI emits at a maximum of 463 nm, PANSI with the same backbone but aryl substituents displays dramatically redshifted emission with a maximum at 494 nm. Both polymers show stable photoluminescence spectra while annealing at 200 °C in inert atmosphere. The PONSI‐based devices with the configuration of ITO/PEDOT:PSS/polymer/Ca/Al turn on at 3.7 V, and emit at a maximum of 461 nm with the CIE coordinates of (0.19, 0.26), a maximum luminance efficiency of 1.40 cd/A, and a maximum brightness of 2036 cd/m² at 13 V. Meanwhile, the emission color of the devices is independent of driving voltage and keeps unchanged during the continuous operation. © 2008 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 46: 4866–4878, 2008     

Synthesis and electroluminescent properties of a phenothiazine‐based polymer for nondoped polymer light‐emitting diodes with a stable orange‐red emission

A novel phenothiazine‐based polymer was synthesized through the Heck reaction of 3,7‐divinyl‐N‐octyl‐phenothiazine with 4,7‐dibromo‐2‐octylbenzotriazole according to the alternating donor–acceptor strategy. The polymer was characterized with ¹H NMR, infrared spectroscopy, gel permeation chromatography, cyclic voltammetry, ultraviolet–visible spectroscopy, and fluorescence spectroscopy. With the polymer used as an active layer, three nondoped polymer light‐emitting diodes (PLEDs) with a double‐layer configuration were fabricated by the spin‐coating approach with different thermal annealing processes. The emission maximum in electroluminescent spectra was stabilized at 616 nm. The maximum luminance reached 2432 cd/m². The coordinate value of Commission International de l'Eclairage 1931 in the double‐layer PLEDs after the thermal treatment was nearly stabilized at (x, y) =(0.62, 0.38). Additionally, the luminous efficiency of device II reached a balanceable state with an increase in the current. Therefore, the polymer had an orange‐red emission with stable chromaticity coordinates under different driving voltages. Finally, a nondoped device with a stable luminous efficiency and chromaticity was obtained. © 2007 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 45: 4867–4878, 2007     

Highly substituted poly(2,3‐diphenyl‐1,4‐phenylenevinylene) derivatives having bulky phenyl and fluorenyl pendant groups: Synthesis,characterization, and electro‐optical properties

Two series of poly(2,3‐diphenyl‐1,4‐phenylenevinylene) (DP‐PPV) derivatives containing multiple bulky substituents were synthesized. In the first series, two different groups were incorporated on C‐5,6 positions of the phenylene moiety to increase steric hindrance and to obtain blue‐shifted emissions. In the second series, bulky fluorenyl groups with two hexyl chains on the C‐9 position were introduced on two phenyl pendants to increase the solubility as well as steric hindrance to prevent close packing of the main chain. Polymers with high molecular weights and fine‐tuned electro‐optical properties were obtained by controlling the feed ratio of different monomers during polymerization. The maximum photoluminescent emissions of the thin films are located between 384 and 541 nm. Cyclic voltammetric analysis reveals that the band gaps of these light‐emitting materials are in the range from 2.4 to 3.3 eV. A double‐layer EL device with the configuration of ITO/PEDOT/P4/Ca/Al emitted pure green light with CIE′1931 at (0.24, 0.5). Using copolymer P6 as the emissive layer, the maximum luminescence and current efficiency were both improved when compared with the homopolymer P4. © 2006 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 44: 6738–6749, 2006     

Imide‐functionalized naphthodithiophene based donor‐acceptor conjugated polymers for solar cells

Donor‐acceptor conjugated polymers containing a new imide‐functionalized naphthodithiophene (INDT) as the acceptor unit and a 2,2'‐bithiophene with varied substituents as the donor unit have been synthesized. The bandgaps of these polymers depend strongly on the dihedral angle of the 2,2'‐bithiophene unit. The 3,3'‐dialkoxy substitution (polymers PDOR / PBOR ) leads to near planar bithiophene conformation due to the well‐known S–O short contact, while the 3,3'‐dialkyl substitution (polymer PDR ) results in significant twisting due to the steric effect. Consequently PDOR / PBOR shows the lowest bandgap of 1.82/1.85 eV while PDR has a bandgap of 2.38 eV. Bulk‐heterojunction solar cells of the polymer/fullerene blends have been fabricated. Preliminary results show that PBOR gives the best device performance with power conversion efficiencies as high as 2.45% in air without any thermal annealing treatment, indicating the promising potential of INDT‐containing conjugated polymers for efficient solar cells. © 2013 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2013 , 51, 3818–3828