Effect of Glass Transition Temperature of Pressure Sensitive Adhesives on Light Leakage in LCD Panel

Pressure-sensitive adhesives (PSA), which mainly are made of acrylic polymers, have been used to fix optical films to liquid crystal display (LCD) cells to prevent contraction or expansion of the optical film under high temperature and high humidity conditions, while residual stress on the polarizing film is generated and light-leakage results from it in the peripheral area of an LCD panel. In this work, we prepared two different kinds of PSAs and tested light leakage with respect to T_g, verifying that T_g would have an effect on light leakage. We calculated their T_g values using the Fox equation and investigated them by DSC. Rheological properties of the PSAs were also acquired by a rotational rheometer which confirm the relation between T_g and dynamic moduli (G′ and G″). It was found that the higher the T_g, the less is an amount of light leaked.     

Donor–acceptor photovoltaic polymers based on 1,4‐dithienyl‐2,5‐dialkoxybenzene with intramolecular noncovalent interactions

Donor–acceptor (D–A) conjugated polymers bearing non‐covalent configurationally locked backbones have a high potential to be good photovoltaic materials. Since 1,4‐dithienyl‐2,5‐dialkoxybenzene ( TBT ) is a typical moiety possessing intramolecular S…O interactions and thus a restricted planar configuration, it was used in this work as an electron‐donating unit to combine with the following electron‐accepting units: 3‐fluorothieno[3,4‐b]thiophene ( TFT ), thieno‐[3,4‐c]pyrrole‐4,6‐dione ( TPD ), and diketopyrrolopyrrole ( DPP ) for the construction of such D–A conjugated polymers. Therefore, the so‐designed three polymers, PTBTTFT , PTBTTPD , and PTBTDPP , were synthesized and investigated on their basic optoelectronic properties in detail. Moreover, using [6,6]‐phenyl‐C₇₁‐butyric acid methyl ester (PC₇₁BM) as acceptor material, polymer solar cells (PSCs) were fabricated for studying photovoltaic performances of these polymers. It was found that the optimized PTBTTPD cell gave the best performance with a power conversion efficiency (PCE) of 4.49%, while that of PTBTTFT displayed the poorest one (PCE = 1.96%). The good photovoltaic behaviors of PTBTTPD come from its lowest‐lying energy level of the highest occupied molecular orbital (HOMO) among the three polymers, and good hole mobility and favorable morphology for its PC₇₁BM‐blended film. Although PTBTDPP displayed the widest absorption spectrum, the largest hole mobility, and regular chain packing structure when blended with PC₇₁BM, its unmatched HOMO energy level and disfavored blend film morphology finally limited its solar cell performance to a moderate level (PCE: 3.91%). © 2018 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2018 , 56, 689–698     

Synthesis and langmuir‐blodgett (LB) film properties of functional α,ω‐diamine amphiphilic materials

We have investigated the synthesis and ultrathin film forming properties of α,ω‐diamine derivatives. The amphiphiles were synthesized as precursors to the formation of ionene polymers. Two materials were investigated: oligothiophene and azobenzene functional groups. These type of materials are of great interest for the preparation of ultrathin film layers with applications for photochemical regulation of liquid crystal (LC) orientation, optical storage media, and electroluminescent displays. Azobenzene and its derivatives are well known photochemical systems exhibiting the reversible cis‐trans photoisomerization. Conjugated oligothiophene derivatives, exhibit interesting optical and electronic properties for applications such as light emitting diodes (LED)s, Schottky diodes, and thin film field‐effect transistors (TFT). The two amphiphiles behaved very differently as Langmuir monolayers and LB films. Dye aggregation was observed with the azobenzene derivatives compared with the oligothiophenes.     

Preparation and physical properties of poly(4,4′‐diamino‐3′‐carbamoylbenzanilide terephthalamide) and poly(4,4′‐diamino‐3′‐carbamoylbenzanilide isophthalamide) films

To prepare thermally stable and high‐performance polymeric films, new solvent‐soluble aromatic polyamides with a carbamoyl pendant group, namely poly(4,4′‐diamino‐3′‐carbamoylbenzanilide terephthalamide) (p‐PDCBTA) and poly(4,4′‐diamino‐3′‐carbamoylbenzanilide isophthalamide) (m‐PDCBTA), were synthesized. The polymers were cyclized at around 200 to 350 °C to form quinazolone and benzoxazinone units along the polymer backbone. The decomposition onset temperatures of the cyclized m‐ and p‐PDCBTAs were 457 and 524 °C, respectively, lower than that of poly(p‐phenylene terephthalamide) (566 °C). For the p‐PDCBTA film drawn by 40% and heat‐treated, the tensile strength and Young's modulus were 421 MPa and 16.4 GPa, respectively. The film cyclized at 350 °C showed a storage modulus (E′) of 1 × 10¹¹ dyne/cm² (10 GPa) over the temperature range of room temperature to 400 °C. © 2000 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 38: 775–780, 2000     

The influence of electron deficient unit and interdigitated packing shape of new polythiophene derivatives on organic thin‐film transistors and photovoltaic cells

A series of new polythiophene derivatives containing a thiazole ring as an electron deficient unit were successfully synthesized via Stille coupling reactions. Synthesized polymers were classified into two types (H‐shape packing and A‐shape packing) based on their interdigitated packing structure induced by different side chain configurations. The thiophene derivatives that contained a thiazole unit ( PT50Tz50 , PTz100 , and PTTz ) exhibited much better thermal stability than did the full thiophene polymers ( PT100 and PTT ). The polymers containing the thiazole unit ( PTz100 and PTTz ) showed a red‐shifted absorption spectrum with clear vibronic structure. In addition, the XRD and AFM results showed that the polymers containing the thiazole unit and interdigitated H‐shape exhibited much better ordered and connected intermolecular structures than did other polymers. The improved intermolecular ordering and surface morphologies directly facilitated charge carrier transport in thin film transistor (TFT) devices, without introducing charge traps, and yielded higher solar cell performance. Among these polymers, the PTTz copolymer exhibited the best TFT performance (μ = 0.050 cm² V^?1 s^?1, on/off ratio = 10⁶, and V_th = ?2 V) and solar cell performance (PCE = 1.39%, J_sc = 6.58 mA cm^?2, and V_oc = 0.58 V). © 2011 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2011     

Synthesis,characterization, photo‐induced alignment,and surface orientation of poly(9,9‐dioctylfluorene‐alt‐azobenzene)s

Three types of bi‐functionalized copolymers ( P1FAz , P2FAz , and P3FAz ) with different numbers of fluorene units and an azobenzene unit were synthesized and characterized using UV–vis and polarized absorption spectroanalysis. The trans‐cis photoisomerization was conformed under 400 nm light irradiation for all copolymers in chloroform. However, in the film state, only the trans‐cis photoisomerization occurred by mono‐fluorene attached copolymer poly[(9,9‐di‐n‐octylfluorenyl‐2,7‐diyl)‐alt‐4,4′‐azobenzene)] ( P1FAz ). Photo‐induced alignment was achieved using the P1FAz film after irradiation with linear polarized 400 nm light and subsequent annealing at 60 °C. Surface orientation of a spin‐coating film of poly(9,9‐didodecylfluorene) ( F12 ) was achieved using the photo‐induced alignment layer of the P1FAz film after annealing at 90 °C. The photo‐induced alignment layer of P1FAz has potential application to the surface orientation technique for appropriate polymers, which will be useful for the fabrication of optoelectronics devices. © 2012 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2012     

Thermal Back‐Isomerization of Spirocyclic Naphtho‐oxazine and Phenanthro‐oxazine Derivatives in Alcohols,Nitriles, and Poly(alkyl methacrylates)

The thermal back‐isomerization of spiro[indole‐naphtho‐oxazine] 1 and spiro[indole‐phenanthro‐oxazine] 2 was studied in a series of primary alcohols, nitriles, and poly(methylmethacrylate), poly(ethylmethacrylate), and poly(isobutyl methacrylate) films by laser‐flash photolysis in the temperature range of 0 – 70°. The decay is monoexponential in fluid solution, but deviates strongly from this behavior in polymeric environments even above the glass transition temperature of the polymers (Tg). In liquids, a very small solvent effect is observed on the isomerization rate constants (k_iso) for 1 , which is attributed mostly to the solvent viscosity η. The values of k_iso for 2 show influence of solvent viscosity and polarity, which were studied by application of a semiempirical relationship that accounts for non‐Markovian processes. The decay kinetics in polymers was described by a Gaussian distribution of the activation energy and by a kinetic model that takes into account the simultaneous relaxation of the probe and the environment. For 1 and 2 , the rate constant at the center of the Gaussian distribution is very similar to the first‐order rate constant in nonpolar solvents. The Gaussian width of the distribution (σ) decreases with temperature and is very similar in all polymers under Tg, and, above Tg, σ decreases more abruptly. We make comparisons of the parameters derived from analysis of both 1 and 2 in polymers, as well as of their behaviors in solution and in polymers.     

5.4 Properties and applications of cellulose triacetate film

The CTA film can be characterized by e.g. its relatively high moisture regain, significantly low birefringence, and moderate mechanical strength. Having been commercialized more than fifty years ago, it has been widely used as photographic film, protective film for polarizing plate, and optical compensation film for liquid crystal display (LCD). The photographic film application exploits the optical isotropy and unique physical properties of the CTA film. In the application of the CTA film to protective film for polarizing plate, its low in-plane birefringence is of particular importance. In the optical compensation to enhance the viewing angle of LCD, the CTA film, because of its moderate retardation in thickness direction (Rth), serves as an element of compensator as well as a base film. Considering the growth of the LCD market, the demand for CTA film is believed to be further expanding.     

Synthesis and properties of conjugated copolycondensates consisting of carbazole‐2,7‐diyl and fluorene‐2,7‐diyl

Carbazole and fluorene‐based random and alternating copolycondensates were synthesized to develop high‐performance blue light‐emitting polymers by improving electron injection ability of poly(N‐aryl‐2,7‐carbazole)s that showed intense blue electroluminescence (EL) with good hole‐injection and ‐transport ability. These copolycondensates absorbed light energy at about λ_max = 390 nm in CHCl₃ and 400 nm in film state, and fluoresced at about λ_max = 417 nm in CHCl₃ and 430 nm in the thin film state. Energy gaps between highest occupied molecular orbital (HOMO) and lowest unoccupied molecular orbital (LUMO) of them were about 2.9 eV, and the energy levels of LUMO situated lower than that of corresponding polycarbazole. Polymer light‐emitting diode devices having configuration of indium tin oxide/poly(3,4‐ethylenedioxythiophene)‐poly(styrenesulfonate)/polymer/CsF/Al using the copolycondensates, poly(N‐arylcarbazole‐2,7‐diyl), and poly(9,9‐dialkylfluorene‐2,7‐diyl), emitted bluish EL at operating voltages lower than 7 V. The device embedded the random copolycondensate showed notably higher performance with maximum luminance of 31,200 cd m^?2 at 11.0 V, and the current efficiencies observed under operating voltages lower than 7 V were higher than those of the other devices. © 2012 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2012     

Preparation and characterization of chiral polyacrylates end‐capped with bornyl groups in the side chains

Chiral polyacrylates with bornyl end‐capped side chains with four kinds of mesogenic moieties (azobenzene, biphenyl, benzoyloxy biphenyl, and phenyl benzoate) were prepared. The phase properties of the polymers were investigated with X‐ray diffraction, differential scanning calorimetry, and polarizing optical microscopy. The thermogravimetric characteristics, the glass‐transition temperatures and weight‐average molecular weights, of the homopolymers were evaluated. The optical properties of the synthesized polymers in diluted solutions and in the thin‐film state were also evaluated. The optical behavior of the composite films upon photoirradiation was investigated through the change in the transmittance of the probe light triggered by ultraviolet (365‐nm) irradiation. Ultraviolet irradiation and heat treatment caused a reversible intensity change of the probe light at λ = 400 nm. The shrinkage of the photoisomerization of the composite films was also investigated with atomic force microscopy. A spot contraction appeared on the surface when it was irradiated with a laser light spot. The contraction was recovered by heat treatment at 80 °C for 10 min. © 2004 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 42: 1075–1092, 2004     

High performance semiconducting polymers containing bis(bithiophenyl dithienothiophene)‐based repeating groups for organic thin film transistors

New dithienothiophene‐containing conjugated polymers, such as poly(2,6‐bis(2‐thiophenyl‐3‐dodecylthiophene‐2‐yl)dithieno[3,2‐b;2′,3′‐d]thiophene, 4 and poly(2,6‐bis (2‐thiophenyl‐4‐dodecylthiophene‐2‐yl)dithieno[3,2‐b;2′,3′‐d]thiophene, 8 have been successfully synthesized via Stille coupling reactions using dodecyl‐substituted thiophene‐based monomers, bistributyltin dithienothiophene, and bistributyltin bithiophene; these polymers have been fully characterized. The main difference between the two polymers is the substitution position of the dodecyl side chains in the repeating group. Grazing‐incidence X‐ray diffraction (GI‐XRD) gave clear evidence of edge‐on orientation of polycrystallites to the substrate. The semiconducting properties of the two polymers have been evaluated in organic thin film transistors (OTFTs). The two conjugated polymers 4 and 8 exhibit fairly high hole carrier mobilities as high as μ_ave = 0.05 cm²/Vs (I_ON/OFF = 3.42 × 10⁴) and μ_ave = 0.01 cm²/Vs, (I_ON/OFF = 1.3 × 10⁵), respectively, after thermal annealing process. The solvent annealed films underwent reorganization of the molecules to induce higher crystallinity. Well‐defined atomic force microscopy (AFM) topography supported a significant improvement in TFT device performance. The hole carrier mobilities of the solvent annealed films are comparable to those obtained for a thermally annealed sample, and were one‐order higher than those obtained with a pristine sample. © 2010 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2010     

A “Cell‐Friendly” Window for the Interaction of Cells with Hyaluronic Acid/Poly‐l‐Lysine Multilayers

Polyelectrolyte multilayers assembled from hyaluronic acid (HA) and poly‐l ‐lysine (PLL) are most widely studied showing excellent reservoir characteristics to host molecules of diverse nature; however, thick (HA/PLL)_n films are often found cell repellent. By a systematic study of the adhesion and proliferation of various cells as a function of bilayer number “n” a correlation with the mechanical and chemical properties of films is developed. The following cell lines have been studied: mouse 3T3 and L929 fibroblasts, human foreskin primary fibroblasts VH‐Fib, human embryonic kidney HEK‐293, human bone cell line U‐2‐OS, Chinese hamster ovary CHO‐K and mouse embryonic stem cells. All cells adhere and spread well in a narrow “cell‐friendly” window identify in the range of n = 12–15. At n < 12, the film is inhomogeneous and at n > 15, the film is cell repellent for all cell lines. Cellular adhesion correlates with the mechanical properties of the films showing that softer films at higher “n” number exhibiting a significant decrease of the Young's modulus below 100 kPa are weakly adherent to cells. This trend cannot be reversed even by coating a strong cell‐adhesive protein fibronectin onto the film. This indicates that mechanical cues plays a major role for cell behavior, also in respect to biochemical ones.     

Poly[2,7‐(9,9‐dihexylfluorene)‐alt‐pyridine] with donor‐acceptor architectures: A new series of blue‐light‐emitting alternating copolymers

A novel series of well‐defined alternating poly[2,7‐(9,9‐dihexylfluorenyl)‐alt‐pyridinyl] (PDHFP) with donor‐acceptor repeat units were synthesized using palladium (0)‐catalyzed Suzuki cross‐coupling reactions in good to high yields. In this series of alternating polymers, 2, 7‐(9,9‐dihexylfluorenyl) was used as the light emitting unit, and the electron deficient pyridinyl unit was employed to provide improved electron transportation. These polymers were characterized by ¹H‐NMR and ¹³C‐NMR, gel permeation chromatography (GPC), thermal analyses, and UV‐vis and fluorescence spectroscopy. The glass transition temperature of copolymers in nitrogen ranged from 110 to 148 °C, and the copolymers showed high thermal stabilities with high decomposition temperatures in the range of 350 to 390 °C in air. The difference in linkage position of pyridinyl unit in the polymer backbone has significant effects on the electronic and optical properties of polymers in solution and in film phases. Meta‐linkage (3,5‐ and 2,6‐linkage) of pyridinyl units in the polymer backbone is more favorable to polymer for pure blue emission and prevention of aggregation of polymer chain than para‐linkage (2,5‐linkage) of the pyridinyl units. © 2004 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 42: 4792–4801, 2004     

Molecular and nanoscale factors governing pressure‐sensitive adhesion strength of viscoelastic polymers

Pressure‐sensitive adhesives (PSAs) are finding increasing applications in various areas of industry and medicine. PSAs are a special class of viscoelastic polymers that form strong adhesive joints with substrates of varying chemical nature under application of light external bonding pressures (1–10 Pa) over short periods of time (1–5 s). To be a PSA, a polymer should possess both high fluidity under applied bonding pressure, to form good adhesive contact, and high cohesive strength and elasticity, which are necessary for resistance to debonding stresses and for dissipation of mechanical energy at the stage of adhesive bond failure under detaching force. For rational design of novel PSAs, molecular insight into mechanisms of their adhesive behavior is necessary. As shown in this review, strength of PSA adhesive joints is controlled by a combination of diffusion, viscoelastic, and relaxation mechanisms. At the molecular level, strong adhesion is the result of a narrow balance between two generally conflicting properties: high cohesive strength and large free volume. These conflicting properties are difficult to combine in a single polymer material. Individually, high cohesive interaction energy and large free volume are necessary but insufficient prerequisites for PSA strength. Evident correlations are observed between the adhesive bond strengths of different PSAs, and their relaxation behaviors are described by longer relaxation times. Innovative PSAs with tailored properties can be produced by physical mixing of nonadhesive long‐ and short‐chain linear parent polymers, with groups at the two ends of the short chains complementary to the functional groups in the recurring units of the long chains. Although chemical composition and molecular structure of such innovative adhesives are unrelated to those of conventional PSAs, their mechanical properties and adhesive behaviors obey the same general laws, such as the Dahlquist's criterion of tack. © 2012 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys, 2012     

Selective Metal‐vapor Deposition on Organic Surfaces

Selective metal‐vapor deposition signifies that metal‐vapor atoms are deposited on a hard organic surface, but not on a soft (low glass transition temperature, low T_g) surface. In this paper, we introduce the origin, extension, and applications of selective metal‐vapor deposition. An amorphous photochromic diarylethene film shows light‐controlled selective metal‐vapor deposition, which is caused by a large T_g change based on photoisomerization, but various organic surfaces, including organic crystal and polymers, can be utilized for achieving selective metal‐vapor deposition. Various applications of selective metal‐vapor deposition, including cathode patterning of organic light‐emitting devices, micro‐thin‐film fuses, multifunctional diffraction gratings, in‐plane electrical bistability for memory devices, and metal‐vapor integration, have been demonstrated.     

Pressure‐sensitive adhesive utilizing molecular interactions between thymine and adenine

A simple pressure‐sensitive adhesion (PSA) system incorporating noncovalent interaction between thymine and adenine is presented. A copolymer having thymine moieties is combined with a low‐molecular‐weight bifunctional adenine cross‐linker. Molecular interactions caused by multiple hydrogen bonds between the thymine and adenine units are evaluated by FT‐IR spectral measurement. Mechanical properties of the PSA are examined by stress–strain curves and dynamic mechanical analysis. As the number of adenine cross‐linkers increases, Young's modulus increases from 0.24 to 3.0 MPa, and the glass transition temperature increases. Furthermore, it is found that the PSAs have adequate adhesive property from their shear strength test. Heat treatment at 80 °C is effective for reinforcement because of interchange of the hydrogen bonds. © 2015 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2016 , 54, 1332‐1338     

Low band‐gap diketopyrrolopyrrole‐containing polymers for near infrared electrochromic and photovoltaic applications

Donor–acceptor type polymers bearing diketopyrrolopyrrole and 3,4‐ethylenedioxythiophene units are reported. The polymers are green and exhibit very low band‐gaps (1.19 eV) with strong and broad absorption (maxima of about 830 nm) in the near infrared (NIR) region in their neutral film states. The polymers display color changes between dark green and light blue with exceptional optical contrasts in the NIR regions of up to 78 and 63% as thin films and single‐layer electrochromic devices, respectively. Fast switching, good stabilities as well as high coloration efficiencies (743–901 cm² C^?1) were also observed. The polymers could also be potentially used as photovoltaic material, with a power conversion efficiency of up to 1.68%. © 2015 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2015 , 53, 1287–1295     

Synthesis,characterization, and properties of polyurethanes containing 1,4:3,6‐dianhydro‐D‐sorbitol

Two‐ and three‐component polyurethanes containing 1,4:3,6‐dianhydro‐D ‐sorbitol (isosorbide) derived from glucose were synthesized using n‐BuSn(?O)OH·H₂O as a catalyst, and the thermal properties (T_g, T_d) of the polymers were investigated by differential scanning calorimetry and thermogravimetric analysis. We carried out molds for polyurethanes, the molds of polyurethanes were obtained. The dynamic mechanical analyzes showed that the storage modulus values of the three‐component polymers were constant to a higher temperature than those of the two‐component polymers. The storage moduli (E′), loss moduli (E″), and values of tan δ for the polymers were obtained. The rigidity of three‐component polymers was increased by the introduction of bisphenol A and diphenylmethane group to two‐component polymer. © 2009 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 47: 6025–6031, 2009     

Blue light‐emitting hyperbranched polymers using fluorene‐co‐dibenzothiophene‐S,S‐dioxide as branches

A series of blue light‐emitting hyperbranched polymers comprising poly(fluorene‐co‐dibenzothiophene‐S,S‐dioxide) as the branch and benzene, triphenylamine, or triphenyltriazine as the core were synthesized by an “A₂ + A₂' + B₃” approach of Suzuki polymerization, respectively. All resulted copolymers exhibited quite comparable thermal properties with the glass transition temperatures in the range of 59–68 °C and relatively high decomposition temperatures over 420 °C. Photoluminescent spectra exhibited slight variation with the molar ratio of the dibenzothiophene‐S,S‐dioxide unit and the size of the core units. Polymer light‐emitting devices demonstrated blue emission with excellent stability of electroluminescence. Copolymers based on smaller core units of benzene and triphenylamine exhibited enhanced device performances regarding to that of triphenyltriazine. With the device configuration of ITO/PEDOT:PSS/polymer/CsF/Al, a maximum luminous efficiency of 4.5 cd A^?1 was obtained with Commission Internationale de L'.Eclairage (CIE) coordinates of (0.16, 0.19) for the copolymer PFSO15B. These results indicated that hyperbranched structure can be a promising strategy to attain spectrally stable blue‐light‐emitting polymers with high efficiency. © 2015 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2015 , 53, 1043–1051     

Synthesis of a pyrrole‐based methine bridge type liquid‐crystalline conjugated polymer

Conjugated polymers consisting of pyrrole or an N‐substituted pyrrole bridged by methine with a mesogenic group were synthesized. Chemical structures of the products were confirmed with IR, NMR, UV–visible (UV–vis) spectroscopy, and gel permeation chromatography analysis. Liquid crystallinity was examined with differential scanning calorimetry measurements and polarizing optical microscopy observations. Liquid crystal domains of the polymer were macroscopically oriented in one direction by an external magnetic force (10 Tesla). The polymer orientation was confirmed by optical microscopy and X‐ray analysis. One of the polymers exhibited a striated fan‐shaped texture when observed with a polarizing optical microscope. This is attributed to the formation of a chiral smectic C (SmC^*) phase, which is a property of ferroelectricity. Spontaneous polarization of the polymer occurred at 110 nC/cm². © 2004 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 43: 616–629, 2005