Microtextured surfaces with gradient wetting properties

Patterned surfaces with microwrinkled surface structures were prepared by thermally evaporating thin aluminum (10-300 nm thick) (Al) layers onto thick prestrained layers of a silicone elastomer and subsequently releasing the strain. This resulted in the formation of sinusoidal periodic surface wrinkles with characteristic wavelengths in the 3-42 μm range and amplitudes as large as 3.6 ± 0.4 μm. The Al thickness dependence of the wrinkle wavelengths and amplitudes was determined for different values of the applied prestrain and compared to a recent large-amplitude deflection theory of wrinkle formation. The results were found to be in good agreement with theory. Samples with spatial gradients in wrinkle wavelength and amplitude were also produced by applying mechanical strain gradients to the silicone elastomer layers prior to deposition of the Al capping layers. Sessile water droplets that were placed on these surfaces were found to have contact angles that were dependent upon their position. Moreover, these samples were shown to direct the motion of small water droplets when the substrates were vibrated.     

Anisotropic mechanical properties of thermoplastic elastomers in situ reinforced with thermotropic liquid‐crystalline polymer fibers revealed by biaxial deformations

The anisotropic mechanical properties of the thermoplastic elastomer (TPE) in situ reinforced with thermotropic liquid‐crystalline polymer (TLCP) fibers were investigated by uniaxial, strip‐biaxial, and equibiaxial tensile measurements. The in situ composite sheets were prepared from an immiscible blend of a TLCP, Rodrun LC3000, and a TPE, styrene‐(ethylene butylene)‐styrene (SEBS) triblock copolymer, by a melt extrusion process. The uniaxial orientation of the TLCP fibers in the TPE matrix generated during processing yielded a significant mechanical anisotropy in the composites. The biaxial tensile measurements clearly demonstrated the anisotropic mechanical properties of the composites: The modulus in the direction parallel to the machine direction (MD) was considerably higher than that in the transverse direction (TD), even at large deformations; in equibiaxial stretching, the yield strain in the MD was smaller than that in the TD; the composite containing 10 wt % of TLCP exhibited the highest mechanical anisotropy among the composites, with 0–30 wt % TLCP. The latter result was in accord with the SEM observation that the composite with 10 wt % of TLCP possessed the best fibrillar morphology and the highest degree of uniaxial orientation of the TLCP fibers. The yield strains in uni‐ and biaxial elongation for the composite containing 10 wt % of TLCP were almost the same as those for the neat styrene‐ethylene butylene‐styrene. The TLCP phase with good fibrillation did not appreciably alter the original yielding characteristics of the elastomer matrix. © 2004 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 43: 135–144, 2005     

Large‐scale aligned fiber mats prepared by salt‐induced pulse electrospinning

In this article, a new large‐scale aligned fiber mats formation method called salt‐induced pulse electrospinning was developed. By electrospinning salted solution in a humid environment, traditional continuous electrospinning changed into pulse electrospinning and aligned fibers were thus formed. The possible mechanisms for the occurrence of salt‐induced pulse electrospinning and the formation of fiber alignment were studied. The continuous electrospinning changing into the pulse electrospinning was due to the change of viscosity and conductivity of salted polymer solution in a wet electrospinning condition. Fishing net‐shaped whipping region of the electrospinning jet during pulse electrospinning process was considered as the key factor for the formation of fiber alignment. The mechanical properties of the aligned fiber mat increased significantly compared with that of the random fiber mat. This aligned fiber preparation method only requires a very low rotating drum speed as the receiver and can produce large‐scale aligned fiber mats for many applications. © 2012 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys, 2012     

Melt transesterification and characterization of segmented block copolyesters containing 2,2,4,4‐tetramethyl‐1,3‐cyclobutanediol

Conventional melt transesterification successfully produced high‐molecular‐weight segmented copolyesters. A rigid, high‐T_g polyester precursor containing the cycloaliphatic monomers, 2,2,4,4‐tetramethyl‐1,3‐cyclobutanediol, and dimethyl‐1,4‐cyclohexane dicarboxylate allowed molecular weight control and hydroxyl difunctionality through monomer stoichiometric imbalance in the presence of a tin catalyst. Subsequent polymerization of a 4000 g/mol polyol with monomers comprising the low‐T_g block yielded high‐molecular‐weight polymers that exhibited enhanced mechanical properties compared to a nonsegmented copolyester controls and soft segment homopolymers. Reaction between the polyester polyol precursor and a primary or secondary alcohol at melt polymerization temperatures revealed reduced transesterification of the polyester hard segment because of enhanced steric hindrance adjacent to the ester linkages. Differential scanning calorimetry, dynamic mechanical analysis, and tensile testing of the copolyesters supported the formation of a segmented multiblock architecture. Further investigations with atomic force microscopy uncovered unique needle‐like, interconnected, microphase separated surface morphologies. Small‐angle X‐ray scattering confirmed the presence of microphase separation in the segmented copolyesters bulk morphology. © 2012 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2012     

Adhesion of nonplanar wrinkled surfaces

Topological patterns on polymer surfaces can significantly alter and control adhesion. In this study, the effect of surface wrinkles on a spherical surface on adhesion has been studied. Surface wrinkling induced by swelling of a crosslinked polydimethylsiloxane elastomer constrained by a stiff, thin surface layer (silicate) is used to produce topographic features of various length scales over a large curved area. By controlling the properties of the stiff layer and the applied strain conditions, surface wrinkles of varying amplitude and wavelength are obtained. The effect of wrinkle morphology on adhesion is quantified, and the results display a transition from enhancement of adhesion to decrease depending upon wrinkle dimensions. A simple phenomenological model is proposed that describes the change of adhesion behavior as a function of wrinkle morphology. Our results provide a critical understanding toward tuning the adhesion behavior of nonplanar surfaces consisting of periodic topographic structures. © 2010 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys, 2011     

Electrical switching of microgel swelling and collapse for display applications

We investigate whether a high‐contrast electronic paper can be formed using a microgel dispersion in which the particles reversibly swell and collapse on cycling the pH. An aqueous dispersion of particles of poly(2‐vinylpyridine) crosslinked with divinylbenzene is studied. It is demonstrated that the pH of the dispersion, and hence the state of the microgel particles, can be potentiostatically controlled using a polyaniline electrode. Electrochemical switching of the dispersion from highly scattering to transparent for all visible wavelengths is achieved. Modification of cell and electrode design is required to reduce the switching time, presently greater than 10 min. © 2012 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys, 2012     

Molecularly templated reaction for forming poly(dimethyl siloxane)–graphene oxide composite elastomers

This study explores the molecularly templated reaction of pyrene‐terminated telechelic poly(dimethyl siloxane) (PDMS) with graphene oxide (GO) to produce composite elastomers. These materials undergo chemical crosslinking between secondary amides near PDMS chain ends and epoxies on the surface of GO as confirmed by infrared spectroscopy, rheology, gel content, and mechanical property measurements. The incorporation of pyrene end groups introduces π–π interactions with GO surfaces that enhance the reaction efficacy of the nearby secondary amide groups. As a comparison, methoxy‐terminated telechelic PDMS containing the same secondary amides near the chain ends did not exhibit appreciable crosslinking with GO. Depending on the concentration of the amide groups, the pyrene‐terminated PDMS/GO elastomer can be highly crosslinked (e.g., up to 96 wt % gel) but highly extensible (e.g., extensional strains of more than 200%). This general strategy could be implemented using other amide containing polymers to produce a wide range of high‐performance thermosets and elastomers. © 2017 Wiley Periodicals, Inc. J. Polym. Sci., Part B: Polym. Phys. 2017 , 55, 1406–1413     

The influence of diffusion time on the properties of sequential interpenetrating PEG hydrogels

Four sets comprising a total of 16 sequential interpenetrating network (SeqIPN) hydrogels were efficiently fabricated via UV initiated thiol‐ene coupling chemistry and from 2 kDa or 8 kDa primary poly(ethylene glycol) (PEG) networks (S2 and S8). Each primary system delivered four different SeqIPNs constructed after 2, 4, 20, and 44 h diffusion of secondary network PEG precursors, 2 kDa and 8 kDa. This allowed the assessment of both mechanical and swelling properties for a wide range of novel hydrogels ranging from loosely crosslinked SeqIPN 8‐8 to densely crosslinked SeqIPN 2‐2 systems. All gel fractions of secondary networks were above 83% and 44 h of diffusion was found sufficient to fully saturate the primary networks. Disperse red functionalized PEGs (2 kDa and 8 kDa) were further used as probes to investigate the diffusion mechanisms. The impact of diffusion time on loosely crosslinked S8 network with a swelling degree of 970% and tensile modulus of 175 kPa displayed a significant change in the final properties. For instance, a 2 h diffusion of 2 kDa PEG precursors generated a SeqIPN 8‐2:2 comprising a secondary network solid content of 34% with a water swelling degree 580% and a tensile modulus of 365 kPa. On saturation, that is, 44 h of diffusion, SeqIPN 2‐8:44 exhibited 64% of secondary network solid content, a swelling capacity of 380% and over fourfold of tensile modulus (758 kPa) when compared with the primary network S8. SeqIPN hydrogel with the highest tensile modulus and lowest degree of water swelling was obtained after 44 h diffusion of 2 kDa PEG precursors within the densely crosslinked S2 primary network. In this case, SeqIPN 2‐2:44 noted a water swelling capability of 280% and a tensile modulus over 1 MPa. The latter was twofold when compared with S2 with a tensile modulus of 555 kPa. Consequently, the diffusion time of secondary network is a promising parameter to control and that enables the fabrication of PEG hydrogels with a wider window of mechanical and swelling properties. © 2012 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2013     

Strain energy function of swollen polybutadiene elastomers studied by general biaxial strain testing

The stress–strain behavior of polybutadiene elastomers with various degrees of swelling is investigated for general biaxial strain. Although a number of previous observations have suggested that the classical neoHookean (NH) model describes the uniaxial data of an elastomer in a highly swollen state, the NH model evidently fails to reproduce the biaxial data. This result indicates that the successful fit of the NH model for the uniaxial data of highly swollen elastomers, which has long been recognized, is superficial. We show that the biaxial data in all of the various swollen states including the neat (unswollen) state are satisfactorily described by an Ogden‐type strain energy function with a single set of parameters. © 2010 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 48: 721–728, 2010     

Organic–inorganic polyurethanes with double decker silsesquioxanes in the main chains: Morphologies,surface hydrophobicity,and shape memory properties

In this contribution, we reported an investigation of the morphologies, surface hydrophobicity, and shape memory properties of the organic–inorganic polyurethanes with double decker silsesquioxane (DDSQ) in the main chains. It was found that the organic–inorganic polyurethanes were microphase‐separated and that the POSS cages in the main chains were self‐organized into the spherical microdomains with the size of 10–50 nm in diameter. The introduction of POSS cages into the main chains resulted in the enhancement of glass transition temperatures (T_g's). In the meantime, the surface dewettability of the materials was significantly enhanced. X‐ray photoelectron spectroscopy (XPS) and atomic force microscopy (AFM) indicates the improvement of the surface hydrophobicity resulted from the enrichment of POSS at the surfaces of the polyurethanes. The mechanical analyses, such as dynamic mechanical analysis (DMA) and creep‐recovery analysis (CRA), indicate that the POSS microdomains dispersed in the polyurethanes behaved as the physical crosslinking sites and promoted the formation of the crosslinked networks. Owing to the introduction of DDSQ into the main chains, the organic–inorganic polyurethanes significantly displayed shape memory properties, in marked contrast to the unmodified and linear polyurethane. The shape memory behavior has been addressed on the formation of the strong physically crosslinked networks in the organic–inorganic polyurethanes. © 2018 Wiley Periodicals, Inc. J. Polym. Sci., Part B: Polym. Phys. 2018 , 56, 893–906     

Effects of nucleating agents on microstructure and fracture toughness of poly(propylene)/ethylene‐propylene‐diene terpolymer blends

The effects of nucleating agents (NAs) on fracture toughness of injection‐molded isotactic poly(propylene)/ethylene‐propylene‐diene terpolymer (PP/EPDM) were studied in this work. Compared with PP/EPDM blends without any NA, PP/EPDM/NA blends show very small and homogeneous PP spherulites. As we expected, PP/EPDM blends nucleated with β‐phase NA aryl amides compound (TMB‐5) present not only a significant enhancement in toughness but also a promotion of brittle‐ductile transition. However, the addition of α‐phase NA 1,3:2,4‐bis(3,4‐dimethylbenzylidene) sorbitol (DMDBS) has no apparent effect on the toughness of the blends. The impact‐fractured surface morphologies of such samples were analyzed via scanning electronic microscope (SEM). More detail work about the toughening mechanisms of elastomer and NA based on elastomer particles size and matrix crystal structures were carried out. Our results suggest that, besides the crystal structures of matrix, the elastomer particles size and size distribution plays an important role in controlling the toughening effect of nucleated PP/elastomer blends. The smaller the elastomer particles size and lower the polydispersity, the more apparent the synergistic toughening effect of NA and elastomer is. This investigation provides a fresh insight into the understanding of toughening mechanism of elastomers in PP blends and facilitates to the design of super toughened PP materials. © 2008 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 47: 46–59, 2009     

Effect of the crosslink density on the morphology and properties of reaction‐injection‐molding poly(urethane urea) elastomers

The effect of the crosslink density on the morphology and properties of reaction‐injection‐molding poly(urethane urea) (PUU) elastomers was investigated. Fourier transform infrared spectroscopy data showed that the linear and crosslinked PUU had entirely different hard‐domain sizes and hard‐segment ordering. A study of the morphology indicated that an increase in the crosslink density increased microphase mixing. Differential scanning calorimetry studies indicated that the hard‐segment initial glass‐transition temperature was independent of the crosslink density. The glass‐transition temperature of the soft segment was highest when the network was perfect. The tensile‐strength behavior showed that the mechanical properties of PUU reached a maximum when the network was perfect. The increase in the resilience of the crosslinked PUU elastomer was higher than that of the linear PUU elastomer with an increase in temperature, and the reduction of the hardness of the former was also higher than that of the latter. © 2004 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 42: 1126–1131, 2004     

Laser‐induced periodic surface structure on a polymer surface: The effect of a prerubbing treatment on the surface structure

The influence of the mechanical rubbing of a polyimide (PI) film on the laser‐induced periodic structure (LIPS) was demonstrated. The periodicity and amplitude of LIPS were greater when the rubbing direction was parallel to the laser polarization direction. The amplitude became small and the periodicity of LIPS did not show an obvious change when the rubbing direction was perpendicular to the laser polarization direction. The effect of the rubbing pretreatment on LIPS was explained on the basis of the wave‐guide effect of rubbing‐induced microgrooves on LIPS formation. The orientation of PI chains induced by mechanical rubbing was relaxed after laser irradiation, and a new orientation of PI chains was formed during the LIPS formation. When the rubbing direction was perpendicular to the laser polarization direction, the orientation of PI chains remained in the rubbing direction. The laser‐irradiated, perpendicularly rubbed PI surface could be used to verify the effects of surface morphologies and intermolecular interactions on liquid‐crystal alignment. © 2003 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 41: 1273–1280, 2003     

A “self‐pinning” adhesive based on responsive surface wrinkles

Surface wrinkles are interesting since they form spontaneously into well‐defined patterns. The mechanism of formation is well‐studied and is associated with the development of a critical compressive stress that induces the elastic instability. In this work, we demonstrate surface wrinkles that dynamically change in response to a stimulus can improve interfacial adhesion with a hydrogel surface through the dynamic evolution of the wrinkle morphology. We observe that this control is related to the local pinning of the crack separation pathway facilitated by the surface wrinkles during debonding, which is dependent on the contact time with the hydrogel. © 2010 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys, 2010     

Strain‐induced crystallization and mechanical properties of functionalized graphene sheet‐filled natural rubber

The effects of functionalized graphene sheets (FGSs) on the mechanical properties and strain‐induced crystallization of natural rubber (NR) are investigated. FGSs are predominantly single sheets of graphene with a lateral size of several hundreds of nanometers and a thickness of 1.5 nm. The effect of FGS and that of carbon black (CB) on the strain‐induced crystallization of NR is compared by coupled tensile tests and X‐ray diffraction experiments. Synchrotron X‐ray scattering enables simultaneous measurements of stress and crystallization of NR in real time during sample stretching. The onset of crystallization occurs at significantly lower strains for FGS‐filled NR samples compared with CB‐filled NR, even at low loadings. Neat‐NR exhibits strain‐induced crystallization around a strain of 2.25, while incorporation of 1 and 4 wt % FGS shifts the crystallization to strains of 1.25 and 0.75, respectively. In contrast, loadings of 16 wt % CB do not significantly shift the critical strain for crystallization. Two‐dimensional (2D) wide angle X‐ray scattering patterns show minor polymer chain alignment during stretching, in accord with previous results for NR. Small angle X‐ray scattering shows that FGS is aligned in the stretching direction, whereas CB does not show alignment or anisotropy. The mechanical properties of filled NR samples are investigated using cyclic tensile and dynamic mechanical measurements above and below the glass transition of NR. © 2012 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys, 2012     

Particle and breath figure formation of triblock copolymers having self‐complementary hydrogen‐bonding units

Novel triblock copolymers having self‐complementary hydrogen‐bonding units were synthesized by using reversible addition–fragmentation transfer polymerization. As characterized by dynamic light scattering and atomic force microscopy, these polymers formed noncovalently crosslinked polymer particles and showed an aggregation behavior by intermolecular and intramolecular interactions. At low concentration, polymers formed nanoparticles, and the particle diameter increased with increasing polymer concentration. Well‐ordered hexagonal microstructures were prepared by “Breath Figure” technique with the triblock copolymers. © 2012 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2012     

Michael addition polymerizations of difunctional amines (AA′) and triacrylamides (B3)

Novel hyperbranched poly(amido amine)s containing tertiary amines on the backbones and acryl or secondary amines as the surface groups were successfully synthesized via the Michael addition polymerizations of a triacrylamide [1,3,5‐triacryloylhexahydro‐1,3,5‐triazine (TT)] and a difunctional amine [n‐butylamine (BA)] NMR techniques were used to clarify the structures of hyperbranched polymers and polymerization mechanism. The reactivity of the secondary amine formed in situ was much lower than that of the primary amines in BA. When the feed molar ratio was 1:1 TT/BA, the secondary amine formed in situ was almost kept out of the reaction before the BA (AA′) and TT (B₃) monomers were consumed, and this led to the formation of A′B₂ intermediates containing one secondary amine group and two acryl groups. The self‐polymerization of the A′B₂ intermediates produced hyperbranched polymers bearing acryl as surface groups. For the polymerization with the feed molar ratio of 1:2 TT/BA, A′₂B intermediates containing one acryl group and two secondary amine groups were accumulated until self‐polymerization started; the self‐polymerization of the intermediates formed hyperbranched polymers with secondary amines as their surface groups. Modifications of surface functional groups were studied to form new hyperbranched polymers. The hyperbranched poly(amido amine)s were amorphous. © 2006 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 44: 6226–6242, 2006     

A facile and controllable synthesis of dual‐crosslinked elastomers based on linear bifunctional polydimethylsiloxane oligomers

Dual‐crosslinked supramolecular elastomers with the hybrid network consisting of hydrogen bonds and covalent bonds combine the reversibility of hydrogen bond and mechanical properties of covalent crosslinking network. In this article, isocyanate mixture is used as curing agent to prepare dual‐crosslinked elastomer based on bifunctional polydimethylsiloxane under mild condition. This method can effectively build up a hybrid network with the designed structure. A series of elastomers with same hydrogen bond density and variable covalent crosslinking degree are obtained. Swelling measurements and ¹H‐NMR spectra confirm the feasibility and controllability of curing method, the increasing of bifunctional isocyanate give rise to higher covalent crosslinking degree, improving the solvent resistance. The studies on viscoelastic property show that the introduction of an irreversible covalent crosslinking network stabilize the hybrid network, restrain the chain movement. The mechanical and self‐healing property studies reveal that the covalent crosslink significantly reinforce the whole network, while the reparable strength seems to mainly depend on the hydrogen bond density. © 2016 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2016 , 54, 3760–3768     

XNBR/LDH nanocomposites: Effect of vulcanization and organic modifier on nanofiller dispersion and strain‐induced crystallization

In elastomer/organo clay nanocomposites, the morphological characteristics, and hence the mechanical properties, of the vulcanizates are strongly influenced by the organic modifier and the vulcanization process. When the elastomer itself undergoes strain‐induced crystallization, both the organic modifier and the dispersed filler particles could significantly influence the crystallization process. These phenomena are very common in case of natural rubber‐based vulcanizates. In this study, the similar effects have been demonstrated with carboxylated nitrile rubber (XNBR) and organically modified layered double hydroxide (O‐LDH)‐based nanocomposites. The effect of size of the organic modifier was obviously visible on the interlayer distance of O‐LDH and also on the morphological reorganization of the dispersed O‐LDH particles during vulcanization process. The strain‐induced crystallization of the XNBR was found to be strongly dependent on the morphological change that occurs during vulcanization process. © 2010 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys, 2010     

Crystallization of polylactic acid under in situ deformation during nonsolvent‐induced phase separation

In this study, we investigate polylactic acid (PLA) crystallization under in situ biaxial extension in a nonsolvent‐induced phase separation foaming process. Our ternary system consists of PLA, dichloromethane (DCM) as solvent and hexane as nonsolvent. For the first time, the formation of a shish‐kebab crystalline morphology is observed in such a solution‐based foaming process in certain solid–liquid phase separated systems. The formation of shish‐kebabs is described based on the coil‐stretch transition concept. The rapid biaxial deformation caused by macropore growth uniaxially stretches the long chains that are tied with at least two single crystals which eventually leads to the formation of shish structures throughout the polymer‐rich phase. The kebab lamellae then form perpendicularly on the shish cores. The scanning electron microscopy (SEM) observations and our interpretation of the crystallization phenomena are confirmed by differential scanning calorimetry (DSC) analysis. The observation of various crystalline morphologies, particularly shish‐kebabs, and the elucidation of their formation mechanisms contribute to the understanding of phase separation and pore growth as well as crystallization in such polymer–solvent–nonsolvent systems. © 2017 Wiley Periodicals, Inc. J. Polym. Sci., Part B: Polym. Phys. 2017 , 55, 1055–1062