Influence of some amino acids on the dynamic swelling behavior of radiation-induced acrylamide hydrogel

The influence of some amino acids—alanine, glycine, valine, glutamine, histidine, phenylalanine, and tryptophan—on the swelling behavior of acrylamide (AAm) hydrogel prepared by γ-radiation was investigated. Swelling experiments of AAm hydrogel were made in the universal buffer solutions and the amino acid solutions at certain pHs at 37°C. These selected pH values were pK₁, pK₂ and isoelectric point (pI) values such as ionization of α-carboxyl groups, ionization of α-amino groups, and the pIs of the amino acids, respectively. The swelling of AAm hydrogel increased when pH values of solutions were increased. The value of equilibrium swelling of AAm hydrogel in the solution of universal buffer was 880% at pH 10.0, whereas it was 670% at pH 2.0. The values of equilibrium swelling of AAm hydrogel in amino acid solutions were between 830 and 965% at pH 10.0, whereas they were between 635 and 775% at pH 2.0. The rate constant of swelling, initial swelling rate, theoretical maximum swelling, diffusional exponent, network parameter, and diffusion coefficient were calculated by swelling kinetics. Diffusions of the amino acid solutions into the hydrogel were generally found as non-Fickian in character. The diffusion coefficients of the hydrogel were between 0.91 × 10⁻⁶ and 2.41 × 10⁻⁶ cm²/s.     

Swelling of dextran gel and osmotic pressure of soluble dextran in the presence of salts

The swelling of dextran gels (Sephadex) in salt solutions with a water activity of 0.937, compared with the swelling in pure water, exhibited anion specificity as evidenced by an increased swelling ratio in the following order: Na₂SO₄ < H₂O < NaCl < NaSCN. The swelling ratio showed a good linear correlation with the osmotic pressure of dextran (500 kD) in these solutions. The salt‐concentration difference (imbalance) between the polymer‐solution side of the membrane and the polymer‐free permeate side during the osmotic‐pressure measurements positively correlated with the effect of the salt on the polymer osmotic pressure. These phenomena conform to Hofmeister‐type (or lyotropic) behavior. The diminishing augmentation of dextran osmotic pressure and the change in the salt‐concentration imbalance with rising NaSCN concentration imply a positive preferential interaction and adsorption of the salt onto the polymer. © 2001 John Wiley & Sons, Inc. J Polym Sci Part B: Polym Phys 39: 2740–2750, 2001     

Synthesis and characterization of a starch‐modified hydrogel as potential carrier for drug delivery system

Synthesis and characterization of a new hydrogel were carried out using a chemically modified starch (starch‐M) consisting of coupling C?C bounds coming from glycidil methacrylate (GMA) onto the polysaccharide structure. ¹³C NMR, ¹H NMR, and FT‐IR spectroscopies were used to confirm the incorporation of such groups onto the starch‐M. The hydrogel was prepared by a crosslinking polymerization of starch‐M using sodium persulfate as an initiating agent. The starch‐M hydrogel shows morphology clearly different from that of the raw starch film due to the presence of voids on its surface. The swelling process of the starch‐M hydrogel was not significantly affected by changes on the temperature or on pH of the surrounding liquid, indicating the such behavior can be then understood by a diffusional process, resulting from its physical–chemical interactions with the solvent. The values of the diffusional exponent n were on the order of 0.45–0.49 for the range of pHs investigated, demonstrating that the water transport mechanism of starch‐M hydrogel is more dependent on Fickian diffusion, that is, controlled by water diffusion. Such starch‐M hydrogel is a promising candidate to be used in transporting and in preserving acid‐responsive drugs, such as corticoids, for the treatment of colon‐specific diseases, for example, Crohn's disease. © 2008 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 46: 2567–2574, 2008     

P(AA-DAC)两性聚电解质水凝胶的合成及性质

以丙烯酸(AA)和丙烯酰氧乙基三甲基氯化铵(DAC)为单体, 采用水溶液聚合法制备了P(AA-DAC)聚电解质水凝胶. 采用红外光谱和核磁共振等方法对其结构进行了表征. 研究了不同组成比的聚电解质水凝胶在去离子水、不同pH值溶液以及不同离子强度盐溶液中的溶胀行为. 研究结果表明, 摩尔比为1∶1的聚电解质水凝胶表现出典型的两性聚电解质凝胶的溶胀行为. 离子强度对其溶胀行为有着显著影响, 在溶液离子强度较高时, 凝胶网络的溶胀主要受溶剂向凝胶内部扩散所控制, 满足Fick型扩散规律n≤0.5, 随着溶液离子强度的增加, 凝胶网络平衡含水量增加, 扩散系数增大.     

Ultrafine hydrogel fibers with dual temperature‐ and pH‐responsive swelling behaviors

Ultrafine hydrogel fibers that were responsive to both temperature and pH signals were prepared through the electrospinning of poly(N‐isopropylacrylamide) (PNIPAAm) and poly(acrylic acid) mixtures in dimethylformamide. Both the diameters (700 nm to 1.2 μm) and packing of the fibers could be controlled through changes in the polymer compositions and PNIPAAm molecular weights. These fibers were rendered water‐insoluble by the addition of either Na₂HPO₄ or poly(vinyl alcohol) (PVA) to the solution, followed by the heat curing of the fibers. The fibers crosslinked with Na₂HPO₄ swelled to 30–120 times in water; this was significantly higher than the swelling of those crosslinked with PVA. The PVA‐crosslinked hydrogel fibers, however, exhibited faster swelling kinetics; that is, they reached equilibrium swelling in less than 5 min at 25 °C. They were also more stable after 1 week of water exposure; that is, they lost less mass and retained their fibrous form better. All the hydrogel fibers showed a drastic increase in the swelling between pH 4 and 5. The PVA‐crosslinked hydrogel fibers exhibited distinct temperature‐responsive phase‐transition behavior of PNIPAAm, whereas the Na₂HPO₄‐crosslinked hydrogel fibers showed altered two‐stage phase transitions that reflected side‐chain modification of PNIPAAm. © 2004 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 42: 6331–6339, 2004     

Swelling kinetics of poly(aspartic acid)/poly(acrylic acid) semi‐interpenetrating polymer network hydrogels in urea solutions

Semi‐interpenetrating network (semi‐IPN) hydrogels, composed of poly(aspartic acid) (PAsp) and poly(acrylic acid) (PAAc) with various ratios of PAsp to AAc, were prepared. In this work, swelling kinetics was investigated through calculating some parameters. The swelling ratios were measured at room temperature, using urea solutions as liquids to be absorbed. Compared to in deionized water, the hydrogels showed larger swelling ratios in urea solutions, which might be attributed to the chemical composition of urea. The equilibrium swelling ratio could achieve 600 g/g, and the equilibrium urea/water contents were more than 0.99. The diffusion exponents were between 0.5 and 0.7, suggesting that the solvent transport into the hydrogel was dominated by both diffusion and relaxation controlled systems. Therefore, the PAsp/PAAc semi‐IPN hydrogels were appropriate to carry substances in a urea/water environment for pharmaceutical, agricultural, environmental, and biomedical applications. © 2010 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 48: 666–671, 2010     

Synthesis of dual pH- and temperature-sensitive poly(N-isopropylacrylamide-co-acrylic acid)/sewage sludge ash hydrogel with the simultaneously high performance of swelling and deswelling

An advanced dual pH- and temperature-sensitive hydrogel (NASH2.5) was optimally synthesized through modification of N-isopropylacrylamide (NIPAM) hydrogel with introducing 5 mol% acrylic acid (AA) and 2.5 wt% sewage sludge ash (SSA). The swelling kinetic results showed that NASH2.5 exhibited both high equilibrium swelling ratio and swelling rate, which was attributed to the higher porous structure as shown in scanning electron microscope, and the more hydrogen bonding formed inside of the hydrogel as investigated in Fourier transform infrared spectrometer. In addition, its curve was better fitted to the pseudo-second-order model, indicating that the water absorption process was dominated by chemisorption through forming the hydrogen bonding among the water molecules and carboxyl/silanol groups of the hydrogel. Compared with the pure NIPAM hydrogel, the water transport mechanism switched from Case I diffusion to Case II diffusion by introduction of AA and further SSA. Furthermore, through the results of the deswelling kinetics in pH value change (from 9 to 4 and 2, respectively), temperature value change (from 25 to 40, 50, and 60°C, respectively), and dual pH and temperature values changes, NASH2.5 not only presented a high pH sensitivity, but also showed high sensitive to temperature by achieving high water recovery ratio in rapid dehydrated rate. Therefore, the dual stimuli-sensitive hydrogel with the simultaneously high performance of swelling and deswelling would provide a suitable alternative for specific applications such as pollutant adsorption.     

Phase Transition of Acrylamide‐Based Polyampholyte Gels in Water

The swelling behavior of acrylamide (AAm)–based polyampholyte hydrogels in water and in aqueous salt (NaCl) solutions was investigated. [(Methacrylamido)propyl]trimethyl‐ammonium chloride (MAPTAC) and acrylic acid (AAc) were used as the ionic comonomer in the hydrogel preparation. Three sets of hydrogels containing 70 mol% AAm and 30 mol% ionic comonomers of varying mole ratios were prepared. The variations of the hydrogel volume in response to changes in pH, and salt concentration were measured. As pH increases from 1, the hydrogel volume V _eq in water first increases and reaches a maximum value at a certain pH. Then, it decreases again with a further increase in pH and attains a minimum value around the isoelectric point (IEP). After passing the collapsed plateau region, the gel reswells again up to pH=7.1. The reswelling of the collapsed gels containing 10 and 4% MAPTAC occurs as a first‐order phase transition at pH=5.85 and 4.35, respectively, while the hydrogel with 1% MAPTAC reswells continuously beyond its IEP. Depending on pH of the solution, the hydrogels immersed in salt solutions exhibit typical polyelectrolyte or antipolyelectrolye behavior. The experimental swelling data were compared with the predictions of the Flory‐Rehner theory of swelling equilibrium including the ideal Donnan equilibria. It was shown that the equilibrium swelling theory qualitatively predicts the experimental behavior of polyampholyte hydrogels.     

Amphoteric surface hydrogels derived from hydrogen-bonded multilayers: reversible loading of dyes and macromolecules

We used hydrogen-bonded multilayers of poly(N-vinylpyrrolidone) (PVPON) and poly(methacrylic acid) (PMAA) as precursors for producing surface-bound hydrogels and studied their pH-dependent swelling and protein uptake behavior using in situ attenuated total reflection Fourier transform infrared spectroscopy and in situ ellipsometry. The hydrogels were produced by selective chemical cross-linking between PMAA units using carbodiimide chemistry and ethylenediamine (EDA) as a cross-linking reagent, followed by complete removal of PVPON from the film obtained by exposing the film to pH 7.5. As shown by in situ ellipsometry, hydrogels exhibit distinctive polyampholytic swelling as a function of pH, with minimum swelling at pH 4.2-5.7, and increased film thickness at both lower and higher pH values. Film swelling at lower pH values occurs as a result of the presence of amino groups within the hydrogels, which originate from the one-end attachment of the EDA cross-linker to PMAA chains. The pH-switching of hydrogel swelling was fast and reversible. The degree of hydrogel swelling could be also controlled by varying the time allowed for cross-linking. The produced hydrogels were able to absorb large amounts of dyes and proteins of opposite charge reversibly, in response to pH variations. Finally, we demonstrate that proteins included within the hydrogel can easily be replaced with linear polycations. These surface hydrogels hold promise for bioseparation and controlled delivery applications.     

Double‐crosslinked reversible redox‐responsive hydrogels based on disulfide–thiol interchange

We present novel redox‐responsive hydrogels based on poly(N‐isopropylacrylamide) or poly(acrylamide), consisting of a reversible disulfide crosslinking agent N,N′‐bis(acryloyl)cystamine and a permanent crosslinking agent N,N′‐methylenebisacrylamide for microfluidic applications. The mechanism of swelling/deswelling behavior starts with the cleavage and reformation of disulfide bonds, leading to a change of crosslinking density and crosslinking points. Raman and ultraviolet‐visible spectroscopy confirm that conversion efficiency of thiol–disulfide interchange up to 99%. Rheological analysis reveals that the E modulus of hydrogel is dependent on the crosslinking density and can be repeatedly manipulated between high‐ and low‐stiffness states over at least 5 cycles without significant decrease. Kinetic studies showed that the mechanical strength of the gels changes as the redox reaction proceeds. This process is much faster than the autonomous diffusion in the hydrogel. Moreover, cooperative diffusion coefficient (D_coop) indicates that the swelling process of the hydrogel is affected by the reduction reaction. Finally, this reversibly switchable redox behavior of bulky hydrogel could be proven in microstructured hydrogel dots through short‐term photopatterning process. These hydrogel dots on glass substrates also showed the desired short response time on cyclic swelling and shrinking processes known from downsized hydrogel shapes. Such stimuli‐responsive hydrogels with redox‐sensitive crosslinkers open a new pathway in exchanging analytes for sensing and separating in microfluidics applications. © 2019 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2019 , 57, 2590–2601     

Fluorescence correlation spectroscopy studies of diffusion of a weak polyelectrolyte in aqueous solutions

We apply fluorescent correlation spectroscopy (FCS) to investigate solution dynamics of a synthetic polyelectrolyte, i.e., a weak polycarboxylic acid in aqueous solutions. The technique brings single molecule sensitivity and molecular specificity to dynamic measurements of polyelectrolyte solutions. Translational diffusion of Alexa-labeled poly(methacrylic acid), PMAA*, chains was studied in very dilute, 10(-4) mg/ml, solutions as a function of solution pH and ionic strength. The observed changes in diffusion coefficients were consistent with about twofold expansion of PMAA* coils when pH was changed from 5 to 8, and with chain contraction for alkaline metal ion concentrations from 0.01 to 0.1 M. The dependence of the hydrodynamic size of PMAA* chains on the counterion type followed the sequence: Li(+)>Na(+) approximately equal to Cs(+)>K(+). The dependence of translational diffusion on polyacid concentration was weak at the low concentration limit, but chain motions were significantly slower at higher polymer concentrations when PMAA chains overlapped. Finally, measurements of dynamics of PMAA* chains in "salt-free" solutions showed that self-diffusion of PMAA* chains significantly slowed down when PMAA concentration was increased, probably reflecting the sensitivity of PMAA* translational motions to the onset of interchain domain formation. These results illustrate the utility of the FCS technique for studying hydrodynamic sizes of polyelectrolyte coils in response to variation in solution pH or concentration of salt and polyelectrolytes. They also suggest that FCS will be a promising technique for selective observation of the dynamics of polyelectrolyte components in complex polymer mixtures.     

Synthesis and characterization of biodegradable hydrophobic–hydrophilic hydrogel networks with a controlled swelling property

A biodegradable polymer network hydrogel system with both hydrophilic and hydrophobic components was synthesized and characterized. The hydrophilic and hydrophobic components were dextran and poly(D,L )lactic acid (PDLLA), respectively. These two polymers were chemically modified for incorporating unsaturated groups for subsequent UV crosslinking to generate a hydrogel with a three‐dimensional network structure. The effects of the reaction conditions on the synthesis of a dextran derivative of allyl isocyanate (dex‐AI) were studied. All newly synthesized materials were characterized by Fourier transform infrared and NMR. The swelling property of the hydrogels was studied in buffer solutions of different pHs. The results of this study showed that a wide‐range swelling property was obtained by changes in the dex‐AI/PDLLA composition ratio, the type and degree of unsaturated groups incorporated into dextran, and the UV photocrosslinking time. The solvent extraction effect on the swelling property of the hydrogels was also studied. © 2000 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 38: 2392–2404, 2000     

pH dependence of PDMS–PMAA IPN morphology and transport properties

The objectives of this study are to probe the pH responsiveness of polydimethyl siloxane (PDMS)/polymethacrylic acid (PMAA) interpenetrating polymer networks (IPNs), and to relate pH-dependent changes in permeation to morphological changes.

PDMS/PMAA IPNs of 70:30 mass ratio on a dry basis were prepared using a monomer immersion method [Macromolecules 33 (10) (2000) 3714]. IPNs made by this method have previously been shown to exhibit a bicontinuous morphology at pH 7 with PMAA structural features of 10–200 nm in dimension [Macromolecules 36 (6) (2003) 1962]. Equilibrium hydration, morphology and diffusion characteristics of the IPNs were investigated at different pH. Equilibrium hydration was gravimetrically determined to be in the range of 0.77–0.9 at pH 7 and 0.42–0.5 at pH 3, corresponding to average hydrations of 0.93 and 0.74 of the PMAA component, respectively. Morphology imaged using laser scanning confocal microscopy (LSCM) showed that the area fraction of fluorescein isothiocyanate labelled dextran (FITC-dextran) accessible regions decreased from pH 7 to 3, consistent with hydration data. Additionally at pH 3, the hydrogel domain appeared to be disconnected. Vitamin B₁₂ (VB₁₂) permeability through the IPN was found to be 1.7 × 10⁻⁷ cm²/s at pH 7, and below detection (<10⁻¹³ cm²/s) at pH 3, consistent with the observed morphology. Dynamic responses in hydration and permeation to pH changes suggests a surface driven phenomenon with response times that are expected to be thickness-dependent.     

Swelling behavior of ionically cross-linked polyampholytic hydrogels in varied salt solutions

Ionically cross-linked polyampholytic hydrogels were synthesized by redox copolymerization of acrylamide and an ionic complex of (N,N-diethylamino)ethyl methacrylate and acrylic acid (designated as PADA hydrogel). The swelling behavior of the hydrogels in water indicated that a minimal equilibrium swelling ratio is found when the molar ratio of anionic/cationic monomers was 1.55. In NaCl solution, the hydrogels exhibited the typical swelling behavior of conventional polyampholytic gels. Their equilibrium swelling ratios increased with an increase in the NaCl concentration. In solutions of multivalent ions (CaCl₂ and trisodium citrate solutions), the equilibrium swelling ratios of the hydrogels increased first and were then followed by a decrease with an increase in salt concentration. Interestingly, an unexpected abrupt swelling phenomenon was observed when the fully swollen hydrogels in salt solution were transmitted to pure water. The unique swelling behavior of PADA hydrogels depends not only on the molar ratio of the anionic/cationic monomers but also on the valency of the ions.     

Preparation and Characterization of Poly(N‐Vinylpyrrolidone‐co‐Methacrylic Acid) Hydrogels

In this study, N‐vinylpyrrolidone (VP)/methacrylic acid (MAA) copolymers have been prepared at three different mole percents, the methacrylic acid composition being around 5, 10, 15%. MAA and VP monomer mixtures have been irradiated in ⁶⁰Co‐γ source at different irradiation doses and percent conversions have been determined gravimetrically. ～80% conversion of monomers into hydrogels were performed at 3.4 kGy irradiation dose. These hydrogels were swollen in distilled water at pH 4.0, 7.0, and 9.0. P(VP/MAA) hydrogel which contains 5% methacrylic acid showed the maximum % swelling at pH 9.0 in water. Diffusion of water was found to be of non‐Fickian character. Diffusion coefficients of water in P(VP/MAA) hydrogels were calculated. Initial swelling rates of P(VP/MAA) hydrogels increased with increasing pH and MAA content in hydrogels. Swelling kinetics of P(VP/MAA) hydrogels was found to be of second order. Thermal behavior of PMAA, PVP and P(VP/MAA) hydrogel were investigated by thermal analysis. P(VP/MAA) hydrogel gained new thermal properties and the temperature for maximum weight loss and temperature for half‐life of P(VP/MAA) hydrogel were determined.     

pH敏感水凝胶聚甲基丙烯酸的超声合成

在超声作用下,以甲基丙烯酸为原料,N,N’-亚甲基双丙烯酰胺为交联剂,过硫酸钾为引发剂,自由基引发聚合制备了pH敏感水凝胶聚甲基丙烯酸,采用红外光谱(FT-IR)和扫描电镜(SEM)对水凝胶分子结构与性能进行表征.在此基础上,重点研究了超声合成对于水凝胶的溶胀性能、消溶胀性能等性质的影响.实验结果表明,超声作用下合成的聚甲基丙烯酸水凝胶溶胀动力学性能以及响应灵敏性均优于常规合成方法.     

Synthesis,swelling properties,and network structure of new stimuli‐responsive poly(N‐acryloyl‐N′‐ethyl piperazine‐co‐N‐isopropylacrylamide) hydrogels

Poly(N‐acryloyl‐N′‐ethyl piperazine‐co‐N‐isopropylacrylamide) hydrogels were prepared by thermal free‐radical copolymerization of N‐acryloyl‐N′‐ethyl piperazine (AcrNEP) and N‐isopropylacrylamide (NIPAM) in solution using N, N′‐methylene bisacrylamide as the crosslinking agent. The gels were responsive to changes in external stimuli such as pH and temperature. The pH and temperature responsive character of the gels was greatly dependent on the monomer content, namely AcrNEP and NIPAM, respectively. The gels swelled in acidic (pH 2) and de‐swelled in basic (pH 10) solutions with a response time of 60 min. With increase in temperature from 23 to 80 °C the swelling of the gels decreased continuously and this effect was different in acidic and basic solutions. The temperature dependence of equilibrium water content of the gels was evaluated by the Gibbs–Helmholtz equation. Detailed analysis of the swelling properties of these new gels in relation to molecular heterogeneity in acidic (pH 2) and basic (pH 10) solutions were performed. Water transport property of the gels was studied gravimetrically. In acidic solution, the diffusion process was non‐Fickian (anomalous) while in basic solution, the diffusion was quasi‐Fickian. The effect was more evident in solution of pH 2 than in pH 10. Various structural parameters of the gels such as number‐average molar mass between crosslink (M_c), the crosslink density (ρ_c), and the mesh size (ξ) were evaluated. The mesh sizes of the hydrogels were between 64 and 783 Å in the swollen state in acidic solution and 20 and 195 Å in the collapsed state in basic solution. The mesh size increased between three to four times during the pH‐dependent swelling process. The amount of unbound water (free water) and bound water of the gels was also evaluated using differential scanning calorimetry. © 2012 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2012     

ABSORPTION OF METAL IONS AND SWELLING PROPERTIES OF POLY(ACRYLIC ACID-CO-ITACONIC ACID) HYDROGELS

Hydrogels of acrylic acid and itaconic acid has been synthesized with different monomers ratios. The swelling process of the different xerogels immersed in water and salt solutions has been studied. The swelling of hydrogels loaded with metal cations (Cu²⁺, Zn²⁺) was also investigated. The swelling process was monitored by the increase in the weight of hydrogel as a function of time. The absorption properties of metal ions were studied by using the hydrogel, and different concentrations of copper and zinc solutions (prepared from sulphate salts). The influence of pH on the absorption process was studied. For the absorption of metal ions, the amount of ions absorbed within the hydrogel can be calculated from the initial and equilibrium concentrations of the metal ions in aqueous phase, the weight of the hydrogel, and the volume of solution used. Metal absorption increased when pH, salt concentration in external solution and itaconic acid content is levelled.

The swelling isotherms which consisted of an initial fast increase levelled off asymptotically to the equilibrium swelling limit. The experimental data clearly suggest that our hydrogels follow a second-order kinetics for both cases (unload and metal loaded). The kinetics rate constant and the equilibrium water content, K, have been calculated for every monomer ratio from the experimental data according to the kinetics equation. Both magnitudes decreased as the itaconic acid content decreases in the xerogels.     

Greffage de l'acide methacrylique sur des films de poly(chlorure de vinyle) par la methode radiochimique directe

Since PVC films do not swell in pure methacrylic acid (MAA) the films were subjected to gamma-rays while dipped in various mixtures MAACHCl₂. Under such conditions, the grafting proceeds smoothly and its rate exhibits a flat maximum for the mixture containing ca. 50% (molar) monomer. The rate satisfies the relationship Rate = KI^0.6 and the over-all activation energy of the process is 4 kcal/mole. MAA grafted PVC films do not swell in solvents for PMAA (such as water or methanol) even for high grafting ratios. This result is unexpected since PTFE films grafted with either acrylic or methacrylic acid swell to a large extent in water and are excellent membranes. The swelling of the grafted PVC films was investigated in mixtures 1,2-dichloroethylene -methanol. It was found that the extent of swelling was highest in the mixture containing 35% methanol. The unusual swelling properties of these grafted films are attributed to strong polar interactions between PVC and PMAA chains.     

Anion effects on the phase transition of N‐isopropylacrylamide hydrogels

NMR spectra were collected for poly(N‐isopropylacrylamide) (PNIPAAm) hydrogel using high‐resolution magic angle spinning (HRMAS) after gel pieces were hydrated in the presence of D₂O, NaF, NaCl, and NaI aqueous solutions. Changes in the peak height intensity of the spectra provide quantitative insight into the phase transition process. The thermodynamic values of the phase transition were calculated using a van't Hoff analysis of the NMR data. Unlike the trend observed for decreases in the (LCST), changes in the enthalpy and entropy did not clearly display a linear dependence with respect to salt concentration. Rather, it was observed that increases in salt concentration did not affect the enthalpy and entropy to the extent as the initial change observed between no salt and 100 mM solutions. Finally, the effect of salts on the hysteresis of the rehydrating process was observed. Hysteresis occurs due to the need for hydrophobic interactions to break down before water is able to infiltrate the polymer matrix. NaF stabilizes hydrophobic interactions while NaI destabilize hydrophobic interactions, causing them to break down at higher temperatures. © 2012 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2012