Mechanical properties of magnetically oriented epoxy

The microstructure of an epoxy system oriented in high magnetic fields (15–25 T) has been observed to consist of highly oriented domains at the molecular level along the direction of the applied field. The changes in the microstructure have been characterized as a function of the magnetic‐field strength and have been investigated microscopically and with wide‐angle X‐ray diffraction. The mechanical properties of the epoxy have been examined in light of nanoindentation experiments at different load levels. The basic results of the experimental investigations for the effect of high magnetic fields on the structure and property of the epoxy are presented. Nanoindentation testing has revealed large differences in the nanomechanical behavior for thermomagnetically processed epoxy specimens. The differences can be ascribed to the microstructural changes (reorientation) of the polymer at the molecular level. © 2004 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 42: 1586–1600, 2004     

Controlled epoxidation of poly(styrene‐b‐isoprene‐b‐styrene) block copolymer for the development of nanostructured epoxy thermosets

To be used as templates for nanostructured thermosets, a commercial poly(styrene‐b‐isoprene‐b‐styrene) (SIS) block copolymer (BCP) was epoxidized by three different epoxidation procedures. An exhaustive analysis of methodologies using metal catalyzed/hydrogen peroxide, dimethyldioxirane (DMDO), and meta‐chloroperbenzoic acid (m‐CPBA) was performed to obtain reactive BCPs. The DMDO approach was the best strategy to obtain highly epoxidized SIS BCP (85 mol %) without formation of side products. Careful control in BCP epoxidation by metal catalyzed/hydrogen peroxide and m‐CPBA approaches led to a maximum epoxidation degree (ED) of approximately 60 mol % without the formation of side products. The ED by metal catalyzed/hydrogen peroxide strategy could be further increased to 69 mol %, but a significant amount of crosslinking, ring opening, and polymer chain scission reactions were detected by spectroscopic and chromatographic techniques. The miscibility of epoxidized BCPs with diglycidyl ether of bisphenol‐A epoxy system before and after curing was analyzed to develop nanostructured epoxy thermosets. For ED higher than 69 mol %, BCPs were miscible, while those with lower ED presented macrophase separation. Highly epoxidized BCPs obtained by the DMDO methodology were successfully used to obtain ordered nanodomains inside the epoxy matrix, as determined by atomic force microscopy. © 2011 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2011     

Poly(ε‐caprolactone)–poly(isobutylene): A crystallizing,hydrogen‐bonded pseudo‐block copolymer

The crystallization of block copolymers (BCPs) under homogeneous and heterogeneous nucleation is currently well understood revealing the strong interplay of crystallization in competition to microphase separation. This article reports investigations on synthesis and crystallization processes in weakly interacting supramolecular pseudo‐BCPs, composed of poly(ε‐caprolactone) (PCL) and poly(isobutylene) (PIB) blocks, connected by a specifically interacting hydrogen bond (thymine/2,6‐diaminotriazine). Starting from ring opening polymerization of ε‐caprolactone, the use of “click”‐chemistry enabled the introduction of thymine endgroups onto PCL polymer, thus generating the fully thymine‐substituted pure PCLs ( 1a , 1b ) as judged via NMR and MALDI analysis. Physical mixing of 1a , 1b with a bivalent, bis(2,6‐diaminotriazine)‐containing molecule ( 2 ) generated the bivalent polymers BC1 and BC2 , whereas mixing of 1a or 1b with the 2,6‐diaminotriazine‐substituted PIB ( 3 ) generated the supramolecular pseudo‐BCPs BC3 and BC4 . Thermal investigations (DSC, Avrami analysis) revealed only minor changes in the crystallization behavior of BC1 – BC4 with Avrami exponents close to three, indicative of a confluence of the growing crystals during the crystallization process. © 2011 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2011     

Reverse mode operation polymer dispersed liquid crystal with a positive dielectric anisotropy liquid crystal

The development of electrically activated chromogenic materials is important for their potential applications in smart windows. Several previous works have reported on reverse mode operation polymer dispersed liquid crystals (PDLCs) based on negative dielectric anisotropy liquid crystals. They have a transparent OFF state, which turns opaque after the application of a suitable external electric field. Nevertheless, these devices have some limitations such as the use of large amount of expensive liquid crystals with peculiar physical‐chemical properties. In addition, a good matching between the refractive index of liquid crystal and the polymer matrix one is required. The main result of this work is the achievement of reverse mode operation devices prepared with a positive dielectric anisotropy liquid crystal and characterized by a high OFF state transmittance obtained by the onset of high intensity built‐in DC electric fields in a direct mode operation PDLC, which allows the OFF state homeotropic alignment of liquid crystal directors. © 2010 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys, 2011     

Aligned carbon cones in free‐standing UV‐Curable polymer composite

A concept where an alternating electric field (dielectrophoresis) is used to assemble and align carbon nanocone particles (CNCs) into microscopic wires in self‐supporting polymer films is demonstrated. The particle fraction is kept low (one‐tenth of the percolation threshold of isotropic mixture), which allows uniform dispersion and efficient UV curing. The alignment leads to the conductivity enhancement of three to four orders of magnitude (from ～10^?7 to ～10^?3 S/m) in the alignment direction. It does not require passing current so the material can be isolated from the alignment electrodes. This prevents electrodes attaching to the film, if the film is adhesive in nature. The alignment can be done using either in‐plane or out‐of‐plane geometries. It is proposed that this concept could be applied in areas such as electrostatic discharge applications where inexpensive conductive or dissipative materials and macroscopic uniformity are prerequisites. © 2011 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys, 2011     

Magnetic orientation of diamagnetic amorphous polymers

Molecular order in an amorphous polymer with anisotropic magnetic susceptibility is altered by applying external magnetic fields. Disks of atactic polystyrene (a‐PS) are prepared by solvent casting outside or inside a magnet. The effect of the magnetic field on the polymer samples is investigated by magnetic levitation and solid state NMR spectroscopy. Magnetic levitation of the a‐PS disks shows that the orientation of disk symmetry axis with respect to the magnetic field gradient depends on the magnitude and direction of the applied field during casting. Similarly, carbon‐13 two‐dimensional cross‐polarization/magic angle spinning rotor‐synchronized NMR measurements in these samples show modulation patterns of the spinning side bands only on disks prepared in the presence of a magnetic field. These findings suggest that macromolecular order could be induced in a fluid or fluid–solid phase transition with cooperative segmental motions reorienting the diamagnetic susceptibility tensor to minimize the magnetic contribution to free energy of the sample. © 2010 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 48: 1009–1015, 2010     

Flow‐induced particle orientation and rheological properties of suspensions of organoclays in thermoplastic resins

The influence of nano‐scale particles on the viscoelastic properties of polymer suspensions is investigated. We have developed a simulation technique for the particle orientation and polymer conformation tensors to study various features of the suspensions. The nano‐particles are modeled as thin rigid oblate spheroid particles and the polymers as FENE‐P type viscoelastic and Newtonian fluid. Both interparticle and polymer‐particle interactions have been taken into account in our numerical computations. The nonlinear viscoelastic properties of nanocomposites of layered silicate particles in non‐Newtonian fluids are examined at the start‐up of shear flow and are interpreted using the model to examine the effects of model parameters as well as flow conditions on particle orientation, viscosity, and first normal stress difference of the suspensions. We have studied the microstructure of polymer‐clay nanocomposites using X‐ray diffraction (XRD) scattering and transmission electron microscopy (TEM). The rheology of these nanocomposites in step‐shear is shown to be fairly well predicted by the model. © 2010 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 48: 2003–2011, 2010     

Effective potential energy curves of H2 molecule evolving in a strong time‐dependent magnetic field

Evolution of hydrogen molecule, starting initially from its field‐free ground state, in a time‐dependent (TD) magnetic field of order 10¹¹ G is presented in a parallel internuclear axis and magnetic field‐axis configuration. Effective potential energy curves (EPECs), in terms of exchange and correlation energy, of the hydrogen molecule as a function of TD magnetic‐field strength, are analyzed through TD density functional computations based on a quantum fluid dynamics approach. The numerical computations are performed for internuclear separation R ranging from 0.1 to 14.0 a.u. The EPECs exhibit field‐dependent significant potential‐well minima both at large internuclear separations and at short internuclear separations with a considerable increase in the exchange and correlation energy of the hydrogen molecule. The results, when compared with the time‐independent (TI) studies involving static TI magnetic fields, reveal TD behavior of field‐dependent crossovers between different spin‐states of hydrogen molecule as indicated by the TI investigations in static magnetic fields. Besides this, present work reveals interesting dynamics in the TD total‐electronic charge‐density distribution of the hydrogen molecule. © 2010 Wiley Periodicals, Inc. Int J Quantum Chem, 2011     

Doubly photoresponsive and water‐soluble block copolymers: Synthesis and thermosensitivity

We report the synthesis and investigation of a new type of photoresponsive block copolymers (BCPs). They were designed to comprise two water‐soluble polymers containing two different photoisomerizable moieties (either azobenzene and spiropyran or two different azobenzenes), with the two constituting blocks that, when separated, exhibit a lower critical solution temperature (LCST) in water and can shift their LCST in opposite directions upon photoisomerization (decrease of LCST for one polymer and increase for the other). A variety of such doubly photoresponsive BCPs were synthesized using either azobenzene‐ or spiropyran‐containing poly(N,N‐dimethylacrylamide) (PDMA), poly(N‐isopropylacrylamide) (PNIPAM) and poly[methoxydi(ethylene glycol) methacrylate] (PDEGMMA). Their thermal phase transition behaviors in aqueous solution before and after simultaneous photoreactions on the two blocks were investigated in comparison with their constituting blocks, by means of solution transmittance (turbidity) and variable‐temperature ¹H NMR measurements. The results show that BCPs displayed a single LCST whose shift upon two photoisomerizations appeared to be determined by the competing and opposing photoinduced effects on the two blocks. Moreover, optically controlling the relative photoisomerization degrees of trans azobenzene‐to‐cis azobenzene and spiropyran‐to‐merocyanine could be used to tune the LCST of BCP solution. This study demonstrates the potential of exploring a more complex photoreaction scheme to optically control the solution properties of water‐soluble thermosensitive BCPs. © 2010 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 48: 4055–4066, 2010     

Aligned single‐wall carbon nanotube polymer composites using an electric field

While high shear alignment has been shown to improve the mechanical properties of single‐wall carbon nanotube (SWNT)‐polymer composites, this method does not allow for control over the electrical and dielectric properties of the composite and often results in degradation of these properties. Here, we report a novel method to actively align SWNTs in a polymer matrix, which permits control over the degree of alignment of the SWNTs without the side effects of shear alignment. In this process, SWNTs were aligned via AC field‐induced dipolar interactions among the nanotubes in a liquid matrix followed by immobilization by photopolymerization under continued application of the electric field. Alignment of SWNTs was controlled as a function of magnitude, frequency, and application time of the applied electric field. The degree of SWNT alignment was assessed using optical microscopy and polarized Raman spectroscopy, and the morphology of the aligned nanocomposites was investigated by high‐resolution scanning electron microscopy. The structure of the field induced aligned SWNTs was intrinsically different from that of shear aligned SWNTs. In the present work, SWNTs are not only aligned along the field, but also migrate laterally to form thick, aligned SWNT percolative columns between the electrodes. The actively aligned SWNTs amplify the electrical and dielectric properties of the composite. All of these properties of the aligned nanocomposites exhibited anisotropic characteristics, which were controllable by tuning the applied field parameters. © 2006 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 44: 1751–1762, 2006     

Oxidation potential of thiophene oligomers: Theoretical and experimental approach

Intrinsic properties of conducting polymers, such as oxidation potential and band gap, are very important for designing new materials with improved properties. Computational chemistry offers suitable tools capable of predicting these quantities. This work presents electrochemical information about accurate oxidation potentials of oligothiophenes and polymer band gap. These are compared to theoretical predictions based on electronic structure calculations at Density Functional Theory levels, coupled with self‐consistent reaction field. All computational protocols gave a qualitative prediction of the experimental trend. © 2011 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys, 2011     

Polymer nanocomposites for electrical energy storage

This review highlights the frontier scientific research in the development of polymer nanocomposites for electrical energy storage applications. Considerable progress has been made over the past several years in the enhancement of the energy densities of the polymer nanocomposites via tuning the chemical structures of ceramic fillers and polymer matrix and engineering the polymer–ceramic interfaces. This article summarizes a range of current approaches to dielectric polymer nanocomposites, including the ferroelectric polymer matrix, increase of the dielectric permittivity using high‐permittivity ceramic fillers and conductive dopants, preparation of uniform composite films based on surface‐functionalized fillers, and utilization of the interfacial coupling effect. Primary attentions have been paid to the dielectric properties at different electric fields and their correlation with film morphology, chemical structure, and filler concentration. This article concludes with a discussion of scientific issues that remain to be addressed as well as recommendations for future research. © 2011 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 49: 1421–1429, 2011     

Crystallization-driven self-assembly of semicrystalline block copolymers and end-functionalized polymers: A minireview

Self-assembly has been a powerful method to fabricate the polymer materials with well-defined structures and morphologies. Such assembled materials have shown wide potential applications in many fields such as nanomaterial, nanomedicine, lithography, and microelectronic. Crystallization has been a general behavior of stereoregular polymers. Besides the various noncovalent interactions, crystallization of polymer blocks or end groups can be an efficient way to manipulate the self-assembly pathway and assembled structures of polymers in both solid and solution. Crystallization-driven self-assembly has been widely implemented for the semicrystalline block copolymers (BCPs) and end-functionalized polymers. This minireview briefly presents the recent progresses in the crystallization-driven self-assembly of BCPs and end-functionalized polymers in both solid and solution states. Formation process, mechanism, and hierarchical structure of the crystallization-induced assemblies for BCPs and end-functionalized polymers are highlighted.     

Advanced materials based on polymer cocrystalline forms

Polymeric “cocrystalline forms,” that is, structures were a polymeric host and a low‐molecular‐mass guest are cocrystallized, were early recognized, and in many cases also well characterized by X‐ray diffraction studies. However, only in the last two decades cocrystalline forms have received attention in material science, due to the ability (of few of them) to maintain an ordered polymer host structure even after guest removal, thus leading to the formation of “nanoporous‐crystalline forms,” for which many applications in the fields of molecular separation and sensors have been proposed. Moreover, in the last decade, an accurate control of the orientation of the polymer cocrystalline phases has been achieved, thus leading to a control of the orientation of the guest molecules, not only in the crystalline phase but also in macroscopic films. In addition, on the basis of this orientation control, in the last few years, cocrystalline films where active molecules are present as guests of polymer cocrystalline phases have been proposed for optical, magnetic and electric applications. In the last few years, it has been also discovered that polymer cocrystallization, when induced by nonracemic guest molecules, can produce stable chiral optical films. © 2012 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys, 2012     

Metallized nanotube polymer composites via supercritical fluid impregnation

Although many metal decorated nanotubes and nanowires appear in the literature, well‐dispersed metal decorated nanotube polymer composites have rarely been reported because of the excessive density mismatch between the decorated nanotubes and polymer matrix. Here, we report a novel method to prepare well‐dispersed, highly functional, metallized nanotube polymer composites (MNPCs) that possess remarkably improved electrical conductivity and mechanical toughness. The MNPCs are prepared by supercritical fluid impregnation of an organometal compound into a premade well‐dispersed single wall carbon nanotube‐polymer composite film. The infused precursor preferentially migrates towards the nanotubes to undergo spontaneous reduction and form nanometer‐scale metal particles leading to an increase in the conductivity of the MNPC films. The environmentally friendly supercritical fluid impregnation process significantly improved the toughness of the composite films, regardless of the presence of metal. Additional functionality can be imparted into the resulting MNPC by infusing other precursors such as magnetic and catalytic metal compounds. © 2011 Wiley Periodicals, Inc.* J Polym Sci Part B: Polym Phys, 2012     

Polymer brushes on multiwalled carbon nanotubes by activators regenerated by electron transfer for atom transfer radical polymerization

The synthesis and characterization of multiwalled carbon nanotube (MWCNT) polymer brushes produced by activators regenerated by electron transfer (ARGET) in atom‐transfer radical polymerization (ATRP) was discussed. The polymer brushes were synthesized by esterification of the MWCNT carboxylic acid groups with hydroxyethyl‐2‐bromoisobutyrate and subsequently used in ARGET ATRP. This created a well defined living polymer brush carbon nanotube of comparatively low polydispersity and a polymer layer 10 nm thick. As, ARGET ATRP uses only minute concentrations of copper (II) catalyst, and is less sensitive to air compared to other living polymerization techniques, this process is a more industry‐compatible route for the commercialization of such materials. The structural and chemical properties were explored by a range of techniques including high resolution transmission electron microscopy, gel permeation chromatography, elemental analysis, Fourier transform infrared spectroscopy, thermogravimetric analysis, and differential scanning calorimetry. In addition, the polymer brush nanotubes were explored for their potential use in films and as fillers. © 2011 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2011     

Block copolymer electrolytes for rechargeable lithium batteries

Ion‐conducting block copolymers (BCPs) have attracted significant interest as conducting materials in solid‐state lithium batteries. BCP self‐assembly offers promise for designing ordered materials with nanoscale domains. Such nanostructures provide a facile method for introducing sufficient mechanical stability into polymer electrolyte membranes, while maintaining the ionic conductivity at levels similar to corresponding solvent‐free homopolymer electrolytes. This ability to simultaneously control conductivity and mechanical integrity provides opportunities for the fabrication of sturdy, yet easily processable, solid‐state lithium batteries. In this review, we first introduce several fundamental studies of ion conduction in homopolymers for the understanding of ion transport in the conducting domain of BCP systems. Then, we summarize recent experimental studies of BCP electrolytes with respect to the effects of salt‐doping and morphology on ionic conductivity. Finally, we present some remaining challenges for BCP electrolytes and highlight several important areas for future research. © 2013 Wiley Periodicals, Inc. J. Polym. Sci., Part B: Polym. Phys. 2014 , 52, 1–16     

Cocrystallization of ethylene/1‐octene copolymer blends during crystallization analysis fractionation and crystallization elution fractionation

Blending of ethylene/1‐octene copolymers can be used to achieve a well‐controlled broad chemical composition distribution (CCD) required in several polyolefin applications. The CCD of copolymer blends can be estimated using crystallization analysis fractionation (CRYSTAF) or crystallization elution fractionation (CEF). Unfortunately, both techniques may be affected by the cocrystallization of chains with different compositions, leading to profiles that do not truly reflect the actual CCD of the polymer. Therefore, understanding how the polymer microstructure and the analytical conditions influence copolymer cocrystallization is critical for the proper interpretation of CRYSTAF and CEF curves. In this investigation, we studied the effect of chain crystallizabilities, blend compositions, and cooling rates on cocrystallization during CEF and CRYSTAF analysis. Cocrystallization is more prevalent when the copolymer blend has components with similar crystallizabilities, one of the components is present in much higher amount, and fast cooling rates are used. CEF was found to provide better CCD estimates than CRYSTAF in a much shorter analysis time. © 2011 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys, 2011     

A novel use of Ti‐POSS as initiator of L‐lactide ring‐opening polymerization

The efficacy of a metal‐silsesquioxane, namely, heptaisobutyl (isopropoxyde)titanium‐polyhedral oligomeric silsesquioxanes (Ti‐POSS), as initiator of the ring‐opening polymerization of L ‐lactide (LLA) has been assessed. Indeed, as demonstrated by proton nuclear magnetic resonance (¹H NMR) spectroscopy and gel permeation chromatography (GPC) measurements, a well‐controlled polymerization occurs via a coordination‐insertion mechanism. Moreover, the above reaction leads to the direct insertion of the silsesquioxane molecule into the polymer backbone, thus producing a hybrid system. Differential scanning calorimetry measurements demonstrated that in comparison with a commercial poly‐L ‐lactide (PLLA), the polymers prepared with Ti‐POSS exhibit a higher crystallinity. Indeed, the presence of silsesquioxane molecules, attached to one end of the polymer chains, has been found to appreciably affect the crystal nucleation density. © 2011 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2011     

Fourier transform infrared/attenuated total reflectance analysis of water diffusion in poly[styrene‐b‐isobutylene‐ b‐styrene] block copolymer membranes

A Fourier transform infrared/attenuated total reflectance technique was used to study the diffusion of water through poly(styrene‐b‐isobutylene‐b‐styrene) block copolymers (BCPs), as well as sulfonated (H⁺) and Na⁺‐sulfonated ionomer versions. Diffusion data were collected and interpreted for these membranes versus polystyrene block composition, degree of sulfonation, Na⁺ ion content in the ionomers, and the effect of initially dry versus prehydrated conditions. An “early time” diffusion coefficient, D, decreased with increasing percent polystyrene for a series of unmodified BCPs. D decreased with increasing degree of sulfonation, and with increasing ion content for the Na⁺‐exchanged samples and this was interpreted in terms of diffusion limitations caused by a strong tendency for ion hydration. The method also yielded information relating to the time evolution of water structure from the standpoint of degree of intermolecular hydrogen bonding. Membrane prehydration causes profound increases in D for both the unmodified BCP and sulfonated samples, as in plasticization. The simultaneous acquisition of information relating to interactions between water molecules and interactions of water molecules with functional groups on the host polymer matrix offers more information than conventional diffusion measurement techniques that simply count transported molecules. © 2005 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 43: 764–776, 2005