Impedance spectroscopy study of Pb<Subscript>2</Subscript>P<Subscript>2</Subscript>O<Subscript>7</Subscript> compound

The lead pyrophosphate, Pb₂P₂O₇, compound was prepared by conventional solid-state reaction and identified by X-ray powder diffractometer. Pb₂P₂O₇ has a triclinic structure whose electrical properties were studied using impedance spectroscopy technique. Both impedance and modulus analysis exhibit the grain and grain boundary contribution to the electrical response of the sample. The temperature dependence of the bulk and grain boundary conductivity were found to obey the Arrhenius law with activation energies E _g = 0.66 eV and E _gb = 0.67 eV, respectively. The scaling behavior of the imaginary part of the complex impedance suggests that the relaxation describes the same mechanism at various temperatures.     

Structural investigation on PEO-based polymer electrolytes dispersed with Al<Subscript>2</Subscript>O<Subscript>3</Subscript> nanoparticles

Thin solid polymer electrolytes based on polyethylene oxide (PEO) and silver triflate (AgCF₃SO₃) dispersed with various concentrations of aluminum oxide (Al₂O₃) nanoparticles have been prepared by solution casting technique. These thin polymer films are found to have thickness of the order of 30 to 100 μm. The X-ray diffraction (XRD) patterns have indicated the amorphous nature of the polymer electrolyte. The differential scanning calorimeter (DSC) traces showed slight change in the glass transition temperature (T _g) whereas the degree of crystallization (X _c) decreases markedly due to the addition of alumina nanoparticles. Fourier transform infrared (FTIR) spectral analysis of all these samples has revealed the presence of absorption bands around 1,000 cm⁻¹; thus indicating the complexation of silver ions with oxygen in PEO. Employing the Wagner’s polarization technique as the standard method, the total ionic transference number for the complexed polymer electrolyte was found to be approximately unity thereby revealing that the significant contribution to electrical conduction was due to ions only. Paper presented at the Third International Conference on Ionic Devices (ICID 2006), Chennai, Tamilnadu, India, December 7–9, 2006     

Gas sensor based on nanosize In<Subscript>2</Subscript>O<Subscript>3</Subscript>:Ga<Subscript>2</Subscript>O<Subscript>3</Subscript> film

Nanosize films of In₂O₃:Ga₂O₃ (96:4 weight %) have been deposited on a glassceramic substrate by the method of rf magnetron sputtering. The surfaces of fabricated films were studied with use of a scanning electron microscope; sizes of grains were determined and the thicknesses of films were measured. In order to prepare a gas-sensitive structure, a thin catalytic palladium layer and ohmic comb contacts were deposited on the In₂O₃:Ga₂O₃ film surface by the method of ion-plasma sputtering. The sensitivity of sensors based on the glassceramic/In₂O₃:Ga₂O₃ (96:4 weight %)/Pd structure to different concentrations of propane and butane gas mixture, as well as to methane was investigated at temperatures of working substance from 250 to 300°C.     

Band structure of a new layered La<Subscript>3</Subscript>Ni<Subscript>4</Subscript>P<Subscript>4</Subscript>O<Subscript>2</Subscript> superconductor

The ab initio FLAPW-GGA calculations of the band structure of a new layered low-temperature (T _C ～ 2.2 K) La₃Ni₄P₄O₂ superconductor are presented. The energy bands, distributions of the densities of electron states, charge states of the atomic layers, low-temperature electron specific heat, and molar Pauli paramagnetic susceptibility for La₃Ni₄P₄O₂ have been determined. They are discussed compared to the existing experimental data.     

NMR study and electrical properties investigation of Zn<Subscript>2</Subscript>P<Subscript>2</Subscript>O<Subscript>7</Subscript>

The α-Zn₂P₂O₇ compound was obtained by conventional solid-state reaction. The sample was characterized by X-ray powder diffraction, solid state ³¹P NMR MAS, and electrical impedance spectroscopy. The solid state ³¹P MAS NMR, performed at 121.49 MHz, shows three isotropic resonances at −21.1, −18.8, and −15.8 ppm, confirming the non-equivalency of the three PO₄ groups in the α-Zn₂P₂O₇ form. They are characterized by different chemical shift tensor parameters with the local geometrical features of the tetrahedra. Electrical impedance measurements of β-Zn₂P₂O₇, form stable for temperature greater than 403 K, were performed as a function of both temperature and frequency. The electrical conduction and dielectric relaxation have been studied. The AC conductivity obeys the universal power law. The approximation type correlated barrier hopping model explains the universal behavior of the n exponent. The impedance plane plot shows semicircle arcs at different temperatures, and an electrical equivalent circuit has been proposed to explain the impedance results. The circuits consist of the parallel combination of bulk resistance R _p and constant phase elements CPE. The simulated spectra show a good correlation with the experimental data.     

Band structure of new layered superconductors BaRh<Subscript>2</Subscript>P<Subscript>2</Subscript> and BaIr<Subscript>2</Subscript>P<Subscript>2</Subscript>

The results of ab initio FLAPW-GGA computations of the band structure of two new layered low-temperature superconductors BaRh₂P₂ and BaIr₂P₂ (with a ThCr₂Si₂ tetragonal structure) are presented. As distinct from the family of the isostructural FeAs superconductors, they feature the complete replacement of the magnetic (Fe) metal by the nonmagnetic 4d (Rh) and 5d (Ir) metals. For BaRh₂P₂ and BaIr₂P₂, the energy bands, the distributions of the densities of electronic states, the Fermi surface topology, and the coefficients of the low-temperature electron specific heat and the molar Pauli paramagnetic susceptibility have been determined. An increase in T _C in the BaRh₂P₂ (1 K) → BaIr₂P₂ (2.1 K) transition can assumingly be attributed to the features of their phonon subsystem.     

Conductivity behavior of the new pyrophosphate NaNi<Subscript>1.5</Subscript>P<Subscript>2</Subscript>O<Subscript>7</Subscript>

NaNi_1.5P₂O₇ compound was obtained by the classic ceramic method at high temperature and was characterized by XRD. It was found to crystallize in the triclinic symmetry with the P-1 space group. The electrical conductivity and modulus characteristics of the system have been investigated in the temperature and the frequency range 586–723 K and 200 Hz–1 MHz, respectively, by means of impedance spectroscopy. The ac conductivity for grain contribution was interpreted using the universal Jonscher’s power law. The exponent s decreased with increasing temperature revealing that the conduction inside the studied material is insured by the correlated barrier hopping (CBH) model. The conduction mechanism was explained with the help of Elliot’s theory, and the Elliot’s parameters were determined. Thermodynamic parameters such as the free energy for dipole relaxation ΔG, the enthalpy ΔH, and the change in entropy ΔS have been calculated.     

CaCuMn<Subscript>6</Subscript>O<Subscript>12</Subscript> vs. CaCu<Subscript>2</Subscript>Mn<Subscript>5</Subscript>O<Subscript>12</Subscript>: A comparative study

The ferrimagnetic compounds Ca(Cu_xMn_3?x)Mn₄O₁₂ of the double distorted perovskites AC₃B₄O₁₂ family exhibit a rapid increase of the ferromagnetic component in magnetization at partial substitution of square coordinated (Mn³⁺)_C for (Cu²⁺)_C. In the transport properties, this is seen as a change of the semiconducting type of resistivity for the metallic one. The evolution of magnetic properties of Ca(Cu_xMn_3?x)Mn₄O₁₂ is driven by strong antiferromagnetic exchange interaction of (Cu²⁺)_C with (Mn³⁺/Mn⁴⁺)_B coordinated octahedra. The competing interactions of (Mn³⁺)_C with (Mn³⁺/Mn⁴⁺)_B lead to the formation of noncollinear magnetic structures that can be aligned by magnetic fields.     

Spherical shape BaO-ZnO-B<Subscript>2</Subscript>O<Subscript>3</Subscript>-SiO<Subscript>2</Subscript> glass powders prepared by spray pyrolysis

Fine-sized BaO-ZnO-B₂O₃-SiO₂ (BZBS) glass powders were directly prepared by high temperature spray pyrolysis. The hollow glass powders prepared at low preparation temperature of 1000 °C had a low density of 2.65 g/cm³. However, the densities of the BZBS powders obtained at preparation temperatures of 1200 and 1400 °C were each 3.92 and 4.13 g/cm³. The mean size of the BZBS glass powders prepared by spray pyrolysis at preparation temperature of 1400 °C was 0.98 μm. The glass transition temperature (T_g) of the prepared BZBS glass powders was 518.9 °C. The dielectric layers formed from the prepared BZBS glass powders with a dense structure had a clean surface and a dense inner structure without voids at the firing temperature of 580 °C. The transparencies of the dielectric layers formed from the prepared BZBS glass powders were higher than 90% within the visible range. PACS 42.70.Ce; 85.60.Pg; 71.55.Jv     

Statistical mechanics of cation ordering in PbSc<Subscript>1/2</Subscript>Ta<Subscript>1/2</Subscript>O<Subscript>3</Subscript> and PbSc<Subscript>1/2</Subscript>Nb<Subscript>1/2</Subscript>O<Subscript>3</Subscript> solid solutions

A model Hamiltonian for B cation ordering (Sc-Nb(Ta)) in PbSc_1/2Nb_1/2O₃ and PbSc_1/2Ta_1/2O₃ solid solutions is constructed. The parameters of the model Hamiltonian are determined from the ab initio calculation within the ionic crystal model with allowance made for the deformability and the dipole and quadrupole polarizabilities of the ions. The temperatures of the phase transition due to the ordering of the B cations are calculated by the Monte Carlo method in the mean-field and cluster approximations. The phase transition temperatures calculated by the Monte Carlo method (1920 K for PbSc_1/2Ta_1/2O₃ and 1810 K for PbSc_1/2Nb_1/2O₃) are consistent with the experimental data (1770 and 1450 K, respectively). The thermodynamic properties of the cation ordering are investigated using the Monte Carlo method.     

The transport and thermal properties of glassy LiPO<Subscript>3</Subscript>/crystalline Al<Subscript>2</Subscript>O<Subscript>3</Subscript> (ZrO<Subscript>2</Subscript>) composite electrolytes

Glassy LiPO₃/crystalline Al₂O₃ and glassy LiPO₃/crystalline ZrO₂ (0–12.5 vol.% of oxide fillers) composite solid electrolytes have been prepared by glass matrix softening. Their thermal and transport properties have been investigated by differential scanning calorimetry (DSC) and impedance spectroscopy methods. The addition of ZrO₂ leads to a decrease in the crystallization temperature of LiPO₃ glass. It was found that the conductivity behavior depends on the nature of the dispersed addition. In the case of the Al₂O₃ addition, the increase in the electrical conductivity is observed. The ionic conductivity of the LiPO₃/10% Al₂O₃ composite reaches 5.8 × 10^?8 S/cm at room temperature. In contrast, the conductivity in the LiPO₃/ZrO₂ composite system decreases.     

Remarkable catalytic activity of Bi<Subscript>2</Subscript>O<Subscript>3</Subscript>/TiO<Subscript>2</Subscript> nanocomposites prepared by hydrothermal method for the degradation of methyl orange

Visible light Bi₂O₃/TiO₂ nanocomposites are successfully prepared with different dosages of Bi₂O₃ by hydrothermal process. All the as-prepared samples are characterized by X-ray diffraction (XRD), scanning and transmission electron microscopes (SEM and TEM), Brunauer-Emmett-Teller analysis (BET), N₂ adsorption-desorption measurement, and UV-Vis diffuse reflectance spectra (DRS). XRD and Raman spectra reveal the anatase phase of both TiO₂ and Bi₂O₃/TiO₂ nanocomposites. X-ray diffraction patterns demonstrate that the bismuth ions did not enter into the lattice of TiO₂, and Bi₂O₃ is extremely dispersive on the surface of TiO₂ nanoparticles. The incorporation of Bi₂O₃ in TiO₂ leads to the spectral response of TiO₂ in the visible light region and efficient separation of charge carriers. The enhanced visible light activity is tested by the photocatalytic degradation of methyl orange under light illumination, and the performance of Bi₂O₃/TiO₂ nanocomposites are superior than that of pure TiO₂ which is ascribed to the efficient charge separation and transfer across the Bi₂O₃/TiO₂ junction. Bi₂O₃/TiO₂ nanocomposite (20 mg) loaded with 0.25 of Bi₂O₃ dispersed in 50 ml of 5 ppm methyl orange solution exhibited the highest photocatalytic activity of 98.86% within 240 min of irradiation, which is attributed to the low band gap, high surface area, and the strong interaction between Bi₂O₃ and TiO₂.     

Effect of Al-Mo codoping on the structure and ionic conductivity of sol-gel derived Li<Subscript>7</Subscript>La<Subscript>3</Subscript>Zr<Subscript>2</Subscript>O<Subscript>12</Subscript> ceramics

Al-Mo codoped Li₇La₃Zr₂O₁₂ ceramics with fine grain were prepared by sol-gel method. The influences of Al-Mo codoping on the structure, microstructure, and conductivity of Li₇La₃Zr₂O₁₂ were investigated by X-ray diffraction (XRD), Raman spectroscopy, scanning electron microscopy (SEM), and impedance spectroscopy. The cubic phase Li₇La₃Zr₂O₁₂ has been stabilized by partial substitution of Al for Li and Mo for Zr. Li_6.6-3yAl_yLa₃Zr_1.8Mo_0.2O₁₂ (0?≤?y?≤?0.1) has been sintered at 1040–1060 °C for 3 h. The liquid sintering facilitated its densification. The relative density of the composition with x?=?0.075 was approximately 96.4%. Results indicated that the Al-Mo codoped LLZO synthesized by sol-gel method effectively lowered its sintering temperature, accelerated densification, and improved the ionic conductivity.     

Interaction of carbon monoxide with In<Subscript>2</Subscript>O<Subscript>3</Subscript> and In<Subscript>2</Subscript>O<Subscript>3</Subscript>-Au nanocomposite

This is an IR spectroscopic study of the interaction of CO with In₂O₃ and the nanocomposite In₂O₃-Au. A mechanism for low-temperature detection of CO on nanocomposite In₂O₃-Au can be determined from these data. This process includes catalytic oxidation of CO through formation of intermediate complexes involving hydroxyl groups of In₂O₃.     

Methane sensor based on SnO<Subscript>2</Subscript>/In<Subscript>2</Subscript>O<Subscript>3</Subscript>/TiO<Subscript>2</Subscript> nanostructure

Two sets of samples of SnO₂/In₂O₃/TiO₂ system have been fabricated with different concentrations of component materials. In the first set TiO₂ with rutile structure was used, while in the second set it has the structure of anatase. Thin films (up to 50 nm) of obtained mixtures were deposited. Their sensitivity and selectivity with respect to methane (CH4) were studied. Nanostructure on the basis of 70%SnO₂ — 10%In₂O₃ — 20%TiO₂(anatase) exhibits sufficient sensitivity to methane.     

On synthesis of BaFe<Subscript>12</Subscript>O<Subscript>19</Subscript>, SrFe<Subscript>12</Subscript>O<Subscript>19</Subscript>, and PbFe<Subscript>12</Subscript>O<Subscript>19</Subscript> hexagonal ferrite ceramics with multiferroid properties

We analyze the possibility of obtaining M-type hexagonal ferrites of barium, strontium, and lead with multiferroid properties with the help of ceramic technology. Using the modified ceramic technology (especially pure initial raw materials, admixture of B₂O₃, and sintering in the oxygen atmosphere), we obtained for the first time the BaFe₁₂O₁₉ and SrFe₁₂O₁₉ samples with intense multiferroid properties at room temperature. At the same time, the employed technology does not make it possible to obtain PbFe₁₂O₁₉ samples exhibiting ferroelectricity. The multiferroid characteristics of experimental samples are compared with the characteristics of classical high-temperature multiferroic BiFeO₃ and with the characteristics of BaFe₁₂O₁₉, SrFe₁₂O₁₉, and PbFe₁₂O₁₉ ferrite ceramics obtained in accordance with polymer precursor technology. We propose a mechanism explaining multiferroid properties of the hexagonal ferrite ceramic samples and note the importance of our results for applications.     

Investigation of ion transport in Li<Subscript>8</Subscript>ZrO<Subscript>6</Subscript> and Li<Subscript>6</Subscript>Zr<Subscript>2</Subscript>O<Subscript>7</Subscript> solid electrolytes

Lithium ionic conductivity and spin-lattice relaxation rates were measured in Li₈ZrO₆ and Li₆Zr₂O₇ solid electrolytes. It was found that the Li₈ZrO₆ solid electrolyte undergoes a transition to the superionic state in the temperature range 673–703 K. It was shown that Li⁺ ions are mobile in particular lattice positions of the Li₆Zr₂O₇ phase, and that ionic conductivity is monotonic at an activation energy of 79.4 kJ/mol.     

Conductivity and spectroscopic studies of Li<Subscript>2</Subscript>O-V<Subscript>2</Subscript>O<Subscript>5</Subscript>-B<Subscript>2</Subscript>O<Subscript>3</Subscript> glasses

Lithium vanadium-borate glasses with the composition of 0.3Li₂O–(0.7-x)B₂O₃–xV₂O₅ (x?=?0.3, 0.325, 0.35, 0.375, 0.4, 0.425, 0.45, and 0.475) were prepared by melt-quenching method. According to differential scanning calorimetry data, vanadium oxide acts as both glass former and glass modifier, since the thermal stability of glasses decreases with an increase in V₂O₅ concentration. Fourier transform infrared spectroscopy data show that the vibrations of [VO₄] structural units occur at V₂O₅ concentration of 45 mol%. It is established that the concentration of V⁴⁺ ions increases exponentially with the growth of vanadium oxide concentration. Direct and alternative current measurements are carried out to estimate the contribution both electronic and ionic conductivities to the value of total conductivity. It is shown that the electronic conductivity is predominant in the total one. The glass having the composition of 0.3Li₂O-0.275B₂O₃-0.475V₂O₅ shows the highest electrical conductivity that has the value of 7.4?×?10^?5 S cm^?1 at room temperature.     

NMR spectrum in a Mn<Subscript>3</Subscript>Al<Subscript>2</Subscript>Ge<Subscript>3</Subscript>O<Subscript>12</Subscript> noncollinear antiferromagnet

The dependence of the NMR frequencies on the external magnetic field in a Mn₃Al₂Ge₃O₁₂ non-collinear 12-sublattice antiferromgnet is calculated using the exchange approximation for the spin dynamics.