Charge carrier mobility,photovoltaic, and electroluminescent properties of anthracene‐based conjugated polymers bearing randomly distributed side chains

This article reports on the synthesis, characterization, and properties of various anthracene‐containing poly (p‐phenylene‐ethynylene)‐alt‐poly(p‐phenylene‐vinylene) (PPE‐PPV) polymers (AnE‐PVs) bearing statistical distributions of various side chains. Primarily, the ratio of linear octyloxy and branched 2‐ethylhexyloxy side chains at the poly(p‐phenylene vinylene) (PPV) parts was varied, leading to the polymers stat, stat1, and stat2. Furthermore, polymers also containing asymmetric substituted PPV and poly(p‐phenylene ethynylene) units (bearing methoxy and 2‐ethylhexyloxy side chains) were prepared yielding stat3, stat4, and stat5. These materials exhibit a broad variation in their photovoltaic properties. It is once more shown that side chains and their distribution can crucially affect the photovoltaic device performance. The introduction of units with asymmetric substitution into these systems seems to be harmful for their utilization in photovoltaic applications. Organic field‐effect transistors were fabricated to investigate hole mobilities in these new materials. Large variance was observed, falling in the range of almost two orders of magnitude, indicating rather different π–π stacking behavior of the polymer backbones owing to side‐chain modifications. Moreover, a selection of the new polymeric systems was investigated regarding their potential for light‐emitting diode (LED) applications. Polymer LEDs using the polymers AnE‐PVstat, ‐stat3, ‐stat4, and ‐stat5, as the active layer showed turn‐on voltage of ～2 V and exhibited red light emission. © 2012 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2012     

Synthesis and photovoltaic properties of copolymers based on benzo[1,2‐b:4,5‐b′]dithiophene and thiophene with electron‐withdrawing side chains

Six alternating conjugated copolymers ( PL1 – PL6 ) of benzo[1,2‐b:4,5‐b′]dithiophene (BDT) and thiophene, containing electron‐withdrawing oxadiazole (OXD), ester, or alkyl as side chains, were synthesized by Stille coupling reaction. The structures of the polymers were confirmed, and their thermal, optical, electrochemical, and photovoltaic properties were investigated. The introduction of conjugated electron‐withdrawing OXD or formate ester side chain benefits to decrease the bandgaps of the polymers and improve the photovoltaic performance due to the low steric hindrance of BDT. Bulk heterojunction polymer solar cells (PSCs) were fabricated based on the blend of the as‐synthesized polymers and the fullerene derivative [6,6]‐phenyl‐C₆₁‐butyric acid methyl ester (PC₆₁BM) in a 1:2 weight ratio. The maximum power conversion efficiency of 2.06% was obtained for PL5 ‐based PSC under the illumination of AM 1.5, 100 mW/cm². © 2011 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2011     

Synthesis and UCST‐type phase behavior of polypeptide with alkyl side‐chains in alcohol or ethanol/water solvent mixtures

A series of thermoresponsive polypeptides bearing 1‐butyl, 1‐hexyl, or 1‐dodecyl side‐chains (i.e., 6a ‐ 6c ) were synthesized by copper‐mediated 1,3‐dipolar cycloaddition with high grafting efficiency (>95%) between side‐chain “clickable” polypeptide, namely poly(γ‐4‐(propargoxycarbonyl)benzyl‐_L‐glutamate) ( 5 ) and 1‐azidoalkanes. 5 with different degree of polymerization (DP = 48–86) were prepared from triethylamine initiated ring‐opening polymerization of γ‐4‐(propargoxycarbonyl)benzyl‐_L‐glutamic acid based N‐carboxyanhydride ( 4 ). ¹H NMR, FTIR, and GPC results revealed the successful preparation of the resulting polypeptides. 6a ‐ 6c showed reversible UCST‐type phase behaviors in methanol, ethanol, and ethanol/water solvent mixtures depending on the polymer main‐chain length, alkyl side‐chain length, weight percentage of ethanol (f_w) in the binary solvent, and so forth. FTIR analysis revealed the presence of the van der Waals interaction between the alkyl pendants of polypeptides and alkyl groups of alcoholic solvents. Variable‐temperature UV‐vis spectroscopy revealed that the UCST‐type phase transition temperature (T_pt) increased as polymer main‐chain length or concentration increased. In ethanol/water solvent mixtures, polypeptide with short alkyl pendant (i.e., 1‐butyl group) and short main‐chain length (DP = 41) showed the widest f_w range and T_pts in the range of 61.0–71.1 °C. © 2016 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2016 , 54, 3425–3435     

Synthesis and comparison of the structure–property relationships of symmetric and asymmetric water‐soluble poly(p‐phenylene)s

Sodium salts of water‐soluble polymers poly{[2,5‐bis(3‐sulfonatopropoxy)‐1,4‐phenylene]‐alt‐[2,5‐bis(hexyloxy)‐1,4‐phenylene]} ( P1 ), poly{[2,5‐bis(3‐sulfonatopropoxy)‐1,4‐phenylene]‐alt‐[2,5‐bis(dodecyloxy)‐1,4‐phenylene]} ( P2 ), poly{[2,5‐bis(3‐sulfonatopropoxy)‐1,4‐phenylene]‐alt‐[2,5‐bis(dibenzyloxy)‐1,4‐phenylene]} ( P3 ), poly[2‐hexyloxy‐5‐(3‐sulfonatopropoxy)‐1,4‐phenylene] ( P4 ), and poly[2‐dodecyloxy‐5‐(3‐sulfonatopropoxy)‐1,4‐phenylene] ( P5 )] were synthesized with Suzuki coupling reactions and fully characterized. The first group of polymers ( P1 – P3 ) with symmetric structures gave lower absorption maxima [maximum absorption wavelength (λ_max) = 296–305 nm] and emission maxima [maximum emission wavelength (λ_em) = 361–398 nm] than asymmetric polymers P4 (λ_max = 329 nm, λ_em = 399 nm) and P5 (λ_max = 335 nm, λ_em = 401 nm). The aggregation properties of polymers P1 – P5 in different solvent mixtures were investigated, and their influence on the optical properties was examined in detail. Dynamic light scattering studies of the aggregation behavior of polymer P1 in solvents indicated the presence of aggregated species of various sizes ranging from 80 to 800 nm. The presence of alkoxy groups and 3‐sulfonatopropoxy groups on adjacent phenylene rings along the polymer backbone of the first set hindered the optimization of nonpolar interactions. The alkyl chain crystallization on one side of the polymer chain and the polar interactions on the other side allowed the polymers ( P4 and P5 ) to form a lamellar structure in the polymer lattice. Significant quenching of the polymer fluorescence upon the addition of positively charged viologen derivatives or cytochrome‐C was also observed. The quenching effect on the polymer fluorescence confirmed that the newly synthesized polymers could be used in the fabrication of biological and chemical sensors. © 2006 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 44: 3763–3777, 2006     

Effect of additive length and chemistry on the morphology of blends of conjugated thiophenes and fullerene derivative acceptor molecules

Small molecule additives have been shown to increase the device efficiency of conjugated polymer (donor) and fullerene derivative (acceptor) based organic solar cells by modifying the morphology of the device active layer. In this paper we conduct a systematic study of how additives affect the donor‐acceptor morphology using molecular dynamics simulations of blends of thiophene‐based oligomers, mimicking poly(3‐dodecylthiophene) (P3DDT) or poly(2,2′:5′,2”‐3,3”‐didocyl‐terthiophene) (PTTT), and fullerene derivatives with additives of varying length and chemical functionalization, mimicking experimentally used additives like methyl ester additives, diiodooctane, and alkanedithiols. We find that functionalization of additives with end groups that are attracted to acceptor molecules are necessary to induce increased donor‐acceptor macrophase separation. In blends where acceptors intercalate between oligomer alkyl side chains, functionalized additives decrease acceptor intercalation. Functionalized additives with shorter alkyl segments increase acceptor macrophase separation more than additives with same chemical functionalization but longer alkyl segments. © 2015 Wiley Periodicals, Inc. J. Polym. Sci., Part B: Polym. Phys. 2015 , 53, 1046–1057     

Water‐soluble poly(ethylene oxide)‐block‐poly(p‐phenylene vinylene) copolymer: Synthesis and characterization

Water‐soluble and photoluminescent block copolymers [poly(ethylene oxide)‐block‐poly(p‐phenylene vinylene) (PEO‐b‐PPV)] were synthesized, in two steps, by the addition of α‐halo‐α′‐alkylsulfinyl‐p‐xylene from activated poly(ethylene oxide) (PEO) chains in tetrahydrofuran at 25 °C. This copolymerization, which was derived from the Vanderzande poly(p‐phenylene vinylene) (PPV) synthesis, led to partly converted PEO‐b‐PPV block copolymers mixed with unreacted PEO chains. The yield, length, and composition of these added sequences depended on the experimental conditions, namely, the order of reagent addition, the nature of the monomers, and the addition of an extra base. The addition of lithium tert‐butoxide increased the length of the PPV precursor sequence and reduced spontaneous conversion. The conversion into PPV could be achieved in a second step by a thermal treatment. A spectral analysis of the reactive medium and the composition of the resulting polymers revealed new evidence for an anionic mechanism of the copolymerization process under our experimental conditions. Moreover, the photoluminescence yields were strongly dependant on the conjugation length and on the solvent, with a maximum (70%) in tetrahydrofuran and a minimum (<1%) in water. © 2005 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 43: 4337–4350, 2005     

Synthesis and photovoltaic properties of copolymers based on bithiophene and bithiazole

Three simple structured D‐A copolymers, PBTBTz‐1 , PBTBTz‐2 , and PBTBTz‐3 , containing bithiophene (BT) donor unit and bithiazole (BTz) acceptor unit with different alkyl chain length were synthesized by the Pd‐catalyzed Stille‐coupling method. The copolymers were characterized by thermogravimetric analysis, UV–vis absorption, electrochemical cyclic voltammetry, and photovoltaic measurements. The results indicate that the introduction of BTz unit to the polythiophene main chain effectively decreases highest occupied molecular orbital levels of the copolymers and increases the open circuit voltage (V_oc) of polymer solar cells (PSCs) based on the copolymers as donor, and the alkyl chain length influences the photovoltaic properties of the polymers significantly. The PSCs based on PBTBTz‐2 and PBTBTz‐3 show higher V_oc up to 0.77 and 0.81 V, respectively. The power conversion efficiency of the PSC based on PBTBTz‐2 :PC₇₀BM = 1:1(w/w) reached 2.58% with short circuit current of 8.70 mA/cm², under the illumination of AM1.5, 100 mW/cm². © 2011 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2011     

Correlating backbone‐to‐backbone distance to ionic conductivity in amorphous polymerized ionic liquids

The morphology and ionic conductivity of poly(1‐n‐alkyl‐3‐vinylimidazolium)‐based homopolymers polymerized from ionic liquids were investigated as a function of the alkyl chain length and counterion type. In general, X‐ray scattering showed three features: (i) backbone‐to‐backbone, (ii) anion‐to‐anion, and (iii) pendant‐to‐pendant characteristic distances. As the alkyl chain length increases, the backbone‐to‐backbone separation increases. As the size of counterion increases, the anion‐to‐anion scattering peak becomes apparent and its correlation length increases. The X‐ray scattering features shift to lower angles as the temperature increases due to thermal expansion. The ionic conductivity results show that the glass transition temperature (T_g) is a dominant, but not exclusive, parameter in determining ion transport. The T_g‐independent ionic conductivity decreases as the backbone‐to‐backbone spacing increases. Further interpretation of the ionic conductivity using the Vogel–Fulcher–Tammann equation enabled the correlation between polymer morphology and ionic conductivity, which highlights the importance of anion hoping between adjacent polymer backbones. © 2011 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys, 2012     

Green‐emitting poly[(1,3‐phenylenevinylene)‐alt‐ (1,4‐phenylenevinylene)]s: Effect of the substitution patterns on the optical properties

Green‐emitting substituted poly[(2‐hexyloxy‐5‐methyl‐1,3‐phenylenevinylene)‐alt‐(2,5‐dihexyloxy‐1,4‐phenylenevinylene)]s ( 6 ) were synthesized via the Wittig–Horner reaction. The polymers were yellow resins with molecular weights of 10,600. The ultraviolet–visible (UV–vis) absorption of 6 (λ_max = 332 or 415 nm) was about 30 nm redshifted from that of poly[(2‐hexyloxy‐5‐methyl‐1,3‐phenylenevinylene)‐alt‐(1,4‐phenylenevinylene)] ( 2 ) but was only 5 nm redshifted with respect to that of poly[(1,3‐phenylenevinylene)‐alt‐(2,5‐dihexyloxy‐1,4‐phenylenevinylene)] ( 1 ). A comparison of the optical properties of 1 , 2 , and 6 showed that substitution on m‐ or p‐phenylene could slightly affect their energy gap and luminescence efficiency, thereby fine‐tuning the optical properties of the poly[(m‐phenylene vinylene)‐alt‐(p‐phenylene vinylene)] materials. The vibronic structures were assigned with the aid of low‐temperature UV–vis and fluorescence spectroscopy. Light‐emitting‐diode devices with 6 produced a green electroluminescence output (emission λ_max ～ 533 nm) with an external quantum efficiency of 0.32%. Substitution at m‐phenylene appeared to be effective in perturbing the charge‐injection process in LED devices. © 2004 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 42: 1820–1829, 2004     

Yellow‐light‐emitting cyano‐substituted poly[(1,3‐phenylene vinylene)‐alt‐(1,4‐phenylene vinylene)] derivative: Its synthesis and optical properties

A soluble cyano‐substituted poly[(1,3‐phenylene vinylene)‐alt‐(1,4‐phenylene vinylene)] derivative ( 9 ) was synthesized and characterized. Comparison between 9 and its model compound ( 10 ) showed that the chromophore in 9 remained to be well defined as a result of a π‐conjugation interruption at adjacent m‐phenylene units. The attachment of a cyano substituent only at the β position of the vinylene allowed the maximum electronic impact of the cyano group on the optical properties of the poly(p‐phenylene vinylene) material. At a low temperature (?108 or ?198 °C), the vibronic structures of 9 and 10 were partially resolved. The absorption and emission spectra of a film of 9 were less temperature‐dependent than those of a film of 10 , indicating that the former had a lower tendency to aggregate. A light‐emitting diode (LED) based on 9 emitted yellow light (λ_max ≈ 578 nm) with an external quantum efficiency of 0.03%. © 2003 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 41: 3149–3158, 2003     

Copoly(p‐phenylene)s containing bipolar triphenylamine and 1,2,4‐triazole groups: Synthesis,optoelectronic properties,and applications

Two novel copoly(p‐phenylene)s ( P1 – P2 ) containing bipolar groups (12.8 and 6.8 mol %, respectively), directly linked hole transporting triphenylamine and electron transporting aromatic 1,2,4‐triazole, were synthesized to enhance electroluminescence (EL) of poly(p‐phenylene vinylene) (PPV) derivatives. The bipolar groups not only enhance thermal stability but also promote electron affinity and hole affinity of the resulting copoly(p‐phenylene)s. Blending the bipolar copoly‐(p‐phenylene)s ( P1 – P2 ) with PPV derivatives ( d6‐PPV ) as an emitting layer effectively improve the emission efficiency of its electroluminescent devices [indium tin oxide (ITO)/poly(3,4‐ethylenedioxythiophene) (PEDOT):poly(styrenesulfonate) (PSS)/polymer blend/Ca (50 nm)/Al (100 nm)]. The maximum luminance and maximum luminance efficiency were significantly enhanced from 310 cd m^?2 and 0.03 cd A^?1 ( d6‐PPV ‐based device) to 1450 cd m^?2 and 0.20 cd A^?1 (blend device with d6‐PPV / P1 = 96/4 containing ～0.5 wt % of bipolar groups), respectively. Our results demonstrate the efficacy of the copoly(p‐phenylene)s with bipolar groups in enhancing EL of PPV derivatives. © 2010 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2010     

Efficient gel‐type electrolyte with bismaleimide via in situ low temperature polymerization in dye‐sensitized solar cells

This study reports the characteristics of gel‐type dye‐sensitized solar cells (DSSCs), fabricated with gel‐type electrolyte containing poly‐1,1′‐(methylenedi‐4,1‐phenylene)bismaleimide (PBMI), or poly‐1,1′‐(3,3′‐dimethyl‐1,1′‐biphenyl‐4,4′‐diyl)bismaleimide (PDBBMI), or poly‐N,N′‐(4‐methyl‐1,3‐phenylene)bismaleimide (PMPBMI), prepared by in situ polymerization of the corresponding monomer without an initiator at 30 °C. Incorporating 0.3 wt % content of exfoliated alkyl‐modified nanomica (EAMNM) into PBMI‐gelled electrolyte leads to higher short‐circuit current density (J_sc = 17.14 mA cm^?2) and efficiency (η = 7.02%) than that of neat PBMI‐gel electrolyte (J_sc = 15.32 mA cm^?2, η = 6.41%). Incorporating 0.3 wt % EAMNM into PBMI‐gelled electrolyte results in remarkably stable device performance under continuous light soaking under one sun (100 mW cm^?2) at 55 °C. The efficiency of DSSCs based on PBMI/0.3 wt % EAMNM‐gelled electrolyte drops by only 1.7% (η = 6.93%) after 500 h of continuous light soaking. © 2010 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2010     

A novel poly(p‐phenylene) containing alternating poly(perfluorooctylethyl acrylate‐co‐methyl methacrylate) and polystyrene grafts by combination of atom transfer radical polymerization and Suzuki coupling processes

A poly(p‐phenylene) (PP), carrying perfectly alternating, well‐defined poly(perfluorooctylethyl acrylate‐co‐methyl methacrylate) [P(FEA‐co‐MMA)] and polystyrene (PS) side chain grafts, was synthesized by the combination of atom transfer radical polymerization (ATRP) and Suzuki cross‐coupling processes. First, dibromobenzene and diboronic ester functional macromonomers of P(FEA‐co‐MMA) and PS, respectively, were prepared by ATRP. In the second step, PP with lateral alternating P(FEA‐co‐MMA) and PS chains was synthesized by a Suzuki coupling reaction in the presence of Pd(PPh₃)₄ catalyst. The wetting behavior of the polymers was studied by measurements of the static contact angle θ of thin films (200?400 nm thickness) using water and n‐hexadecane as wetting liquids. The obtained fluorinated PP showed high static contact angles with both interrogating liquids, exhibiting simultaneously hydrophobic (θ_w = 111°) and lipophobic (θ_h = 67°) properties. © 2012 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2012     

Synthesis,characterization, and structure–property investigation of conformationally rigid regioisomers of poly(p‐phenylene ethynylene)s

A series of rigid poly(p‐phenylene ethynylene)s ( PPE1 – PPE4 ) with biphenyl‐ ( M1–M3 ) and phenyl‐ ( M4 ) side groups is prepared from appropriately functionalized monomers. Herein, the solution and solid state absorption studies show the polymers have adopted twisted and rigid conformations, as supported by deep HOMO energy levels (?5.76 to ?5.81 eV). The absorption maxima of PPE1–PPE3 are shifted to shorter wavelength (λ_max = 375–381 nm) as compared to linear poly(p‐phenylene ethynylene)s (446 nm), implying a nonplanar conformation. The self‐assembly of polymers into fibers is examined using scanning electron microscopy. The fibers are not observed in PPE4 with short phenyl side group, suggesting the important role of the interplay between rigidity, position, and size of the side chains toward the formation of fibers. © 2016 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2016 , 54, 3652–3662     

Synthesis and characterization of new sulfone‐derivatized phenylenevinylene‐based conjugated copolymers with evolving energy levels and gaps

A new series of stable, processable, and chain end functionalizable sulfone‐derivatized phenylenevinylene‐based conjugated polymers (SFPVs) containing different donor type comonomers have been synthesized and characterized. The polymer main chains are consisted of a sulfone‐phenylene electron accepting unit coupled with an electron donating unit which is derived from one of the dialdehyde comonomers based on benzene, thiophene, and pyrrole (with or without alkoxy side chains). The optical energy gaps (E_g) of the new polymers (in solvent) are in a range of 1.9–2.3 eV, with the lowest energy gap obtained from the polymer containing pyrrole as the donor unit. By using a combination of strong donor unit (such as pyrrole) and a relatively weak but stable acceptor unit (sulfone‐substituted benzene), E_g of the conjugated polymers can be tailored to below 2 eV, while the vinylene bonds on the polymer main chain are still chemically stable to survive strong basic conditions as compared with the S,S‐dioxo‐thiophene‐based PTV polymers developed earlier for potential supra‐molecular block copolymer systems. The lowest energy gap P(Pyrrole‐SFPV) exhibited 10 times better photoelectric power conversion efficiency than P(TV‐SFPV). © 2011 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2012     

In situ current voltage measurements for optimization of a novel fullerene acceptor in bulk heterojunction photovoltaics

The evaluation of the power conversion efficiency (PCE) of new materials for organic bulk heterojunction (BHJ) photovoltaics is difficult due to the large number of processing parameters possible. An efficient procedure to determine the optimum conditions for thermal treatment of polymer‐based bulk heterojunction photovoltaic devices using in situ current‐voltage measurements is presented. The performance of a new fullerene derivative, 1,9‐dihydro‐64,65‐dihexyloxy‐1,9‐(methano[1,2] benzomethano)fullerene[60], in BHJ photovolatics with poly(3‐hexylthiophene) (P3HT) was evaluated using this methodology. The device characteristics of BHJs obtained from the in situ method were found to be in good agreement with those from BHJs annealed using a conventional process. This fullerene has similar performance to 1‐(3‐methoxycarbonyl)propyl‐1‐phenyl‐[6,6]‐methano fullerene in BHJs with P3HT after thermal annealing. For devices with thickness of 70 nm, the short circuit current was 6.24 mA/cm² with a fill factor of 0.53 and open circuit voltage of 0.65 V. The changes in the current‐voltage measurements during thermal annealing suggest that the ordering process in P3HT dominates the improvement in power conversion efficiency. © 2011 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys, 2012     

Improved phase separation in polymer solar cells by solvent blending

The effect of solvent blending on the performance of an anthracene‐containing poly(p‐phenylene‐ethynylene)‐alt‐poly(p‐phenylene‐vinylene) backbone‐based donor polymer with asymmetrically substituted branched 2‐ethylhexyloxy and methyloxy side‐chains in bulk heterojunction solar cells is reported. This copolymer yields relatively high open‐circuit voltages with fullerene‐based electron acceptors. We systematically studied the thin‐film blend morphology and solar cell performance as a function of solvent composition (chlorobenzene to chloroform ratio) and polymer to [6,6]‐phenyl C61‐butyric acid methylester (PCBM) ratio. We combined photophysical investigations with atomic force microscopy and grazing incidence wide‐angle X‐ray scattering to elucidate the solid‐state morphology in thin films. In the investigated polymer system, the blend morphology becomes independent of the supporting solvent for high PCBM concentrations. Deposition from solvent blends rather than from pure chlorobenzene facilitates the beneficial phase separation between polymer and PCBM, leading to improved charge transport properties (short‐circuit currents) at lower PCBM concentrations. © 2013 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys, 2013, 51, 868–874     

Revisiting the crystallization of poly(2‐alkyl‐2‐oxazoline)s

Poly(2‐alkyl‐2‐oxazoline)s (PAOx) exhibit different crystallization behavior depending on the length of the alkyl side chain. PAOx having methyl, ethyl, or propyl side chains do not show any bulk crystallization. Crystallization in the heating cycle, that is, cold crystallization, is observed for PAOx with butyl and pentyl side chains. For PAOx with longer alkyl side chains crystallization occurs in the cooling cycle. The different crystallization behavior is attributed to the different polymer chain mobility in line with the glass transition temperature (T_g) dependency on alkyl side chain length. The decrease in chain mobility with decreasing alkyl side chain length hinders the relaxation of the polymer backbone to the thermodynamic equilibrium crystalline structure. Double melting behavior is observed for PButOx and PiPropOx which is explained by the melt‐recrystallization mechanism. Isothermal crystallization experiments of PButOx between 60 and 90 °C and PiPropOx between 90 and 150 °C show that PAOx can crystallize in bulk when enough time is given. The decrease of T_g and the corresponding increase in chain mobility at T > T_g with increasing alkyl side chain length can be attributed to an increasing distance between the polymer backbones and thus decreasing average strength of amide dipole interactions. © 2015 Wiley Periodicals, Inc. J. Polym. Sci., Part B: Polym. Phys. 2016 , 54, 721–729     

Para‐linked and meta‐linked cationic water‐soluble fluorene‐containing poly(aryleneethynylene)s: Conformational changes and their effects on iron–sulfur protein detection

Four para‐linked or meta‐linked cationic water‐soluble fluorene‐containing poly(aryleneethynylene)s (PAEs) were synthesized to investigate the solvent‐induced π‐stacked self‐assembly. These PAE backbones are composed of fluorenylene and phenylene units, which are alternatively linked by ethynylene bonds. UV–vis absorption and photoluminescence spectra were used to study their conformational changes as solvent was gradually changed from MeOH to H₂O. In pure water, with gradually increased meta‐phenylene content (0, 50, and 100%), they underwent a gradual transition process of conformation from disordered aggregate structure to helix structure, which was not compactly folded. Moreover, the polymer with an ammonium‐functionalized side chain on the meta‐phenylene unit appeared to adopt a more incompact or extended helix conformation than the corresponding one without this side chain. Furthermore, the conformational changes of these cationic PAEs in H₂O were used to study their effects on biological detection. Rubredoxin (Rd), a type of anionic iron–sulfur‐based electron transfer protein, was chosen to act as biological analyte in the fluorescence quenching experiments of these polymers. Preliminary results suggest that they all exhibit amplified fluorescence quenching, and that the polymer with more features of helix conformation tends to be quenched by Rd more efficiently. © 2006 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 44: 5424–5437, 2006     

Synthesis of new poly(amide imide)s with (n‐alkyloxy)phenyloxy side branches

Two series of new poly(amide imide)s having (n‐alkyoxy)phenyloxy side branches with various lengths, poly{p‐phenyleneiminoterephthaloylimino‐p‐phenylene[3,6‐di(n‐alkyloxy)phenyloxy]pyromellitimide}s ( PC _m TA s, m = 4, 8, 12) and poly{p‐phenyleneiminosebacoylimino‐p‐phenylene[3,6‐di(n‐alkyloxy)‐phenyloxy]‐ pyromellitimide}s ( PC _m SeA s, m = 4, 8, 12), were prepared by condensation of terephthalamide‐N,N′‐4,4′‐dianiline ( TA ) and sebacamide‐N,N′‐4,4′‐dianiline ( SeA ) with 3,6‐di[4‐(n‐alkyloxy)phenyloxy]pyromellitic dianhydrides , respectively. The inherent viscosities of the polymers were in the 0.82–1.20 dL/g range. The polymers were highly soluble in N‐methylpyrolidinone (NMP), even at room temperature and soluble in other polar aprotic solvents on heating. The PC _m TA s, which have aromatic backbones, were thermally more stable (431–442 °C) than the PC _m SeA s, which have an octamethylene unit in the main chain (407–409 °C). Degradation of weight up to 900 °C corresponded with the loss of side chain contents. The PC _m TA s exhibited no phase transition, whereas two endothermic peaks were observed for each of the PC _m SeA s. Wide‐angle X‐ray diffractometer investigations revealed that both polymers are amorphous and the n‐alkyloxy side chains are present in a layered structure. © 2001 John Wiley & Sons, Inc. J Polym Sci Part A: Polym Chem 39: 3818–3825, 2001