Influence of multiwall carbon nanotubes on morphological and structural changes during UV irradiation of syndiotactic polypropylene films

The effect of UV irradiation on the morphology and structure of syndiotactic polypropylene (sPP) is investigated both for pure films and those filled with multiwall carbon nanotubes (MWCNTs). UV treatment causes a structural reorganization of pure sPP films. It seems that the incorporation of MWCNTs has a strong stabilizing effect, with nanotubes acting as a limiter of the UV‐induced chain breakage, especially when a good dispersion of carbon nanotubes in the polymer is achieved. The incorporation of MWCNTs introduces a high concentration of defects in the crystal structure of sPP, which limits the UV‐induced growth of crystallites, and prevents the development and propagation of cracks caused by UV irradiation. © 2012 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys, 2012     

Using carbon nanotubes to detect polymer transitions

Raman spectral shifts of single‐wall carbon nanotubes embedded in polymer systems were used to measure transitions in polymers. Glass‐transition temperatures and secondary transitions were observed, and Raman spectroscopic data were compared with dynamic mechanical tests for a thermosetting and a thermoplastic polymer. The data confirm that the Raman spectral response of carbon nanotubes embedded in polymers is sensitive to polymer transitions. © 2001 John Wiley & Sons, Inc. J Polym Sci Part B: Polym Phys 39: 1492–1495, 2001     

Polymer coating of carboxylic acid functionalized multiwalled carbon nanotubes via reversible addition‐fragmentation chain transfer mediated emulsion polymerization

In this work, successful polymer coating of COOH‐functionalized multiwalled carbon nanotubes (MWCNTs) via reversible addition fragmentation chain transfer (RAFT) mediated emulsion polymerization is reported. The method used amphiphilic macro‐RAFT copolymers as stabilizers for MWCNT dispersions, followed by their subsequent coating with poly(methyl methacrylate‐co‐butyl acrylate). Poly(allylamine hydrochloride) was initially used to change the charge on the surface of the MWCNTs to facilitate adsorption of negatively charged macro‐RAFT copolymer onto their surface via electrostatic interactions. After polymerization, the resultant latex was found to contain uniform polymer‐coated MWCNTs where polymer layer thickness could be controlled by the amount of monomer fed into the reaction. The polymer‐coated MWCNTs were demonstrated to be dispersible in both polar and nonpolar solvents. © 2012 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2013     

Synthesis and characterization of water‐dispersible,superparamagnetic single‐wall carbon nanotubes decorated with iron oxide nanoparticles and well‐defined chelating diblock copolymers

A novel approach for the fabrication of magneto‐active carbon nanotubes (CNTs) stabilized in aqueous media, involving the combination of carboxylated single‐wall carbon nanotubes (SWCNTs) with a new class of methacrylate‐based chelating diblock copolymers, is described. More precisely, a well‐defined diblock copolymer consisting of hexa(ethylene glycol) methyl ether methacrylate (hydrophilic and thermo‐responsive) and 2‐(acetoacetoxy)ethyl methacrylate (hydrophobic and metal‐chelating) synthesized by reversible addition‐fragmentation chain transfer polymerization has been used to prepare polymer‐coated magneto‐active SWCNTs decorated with iron oxide nanoparticles. Further to the characterization of the compositional and thermal properties using transmission electron microscopy, Fourier transform infrared spectroscopy, X‐ray diffraction spectroscopy and thermal gravimetric analysis, assessment of the magnetic characteristics by vibrational sample magnetometry disclosed superparamagnetic behavior at room temperature. The latter, combined with the thermo‐responsive properties of the polymeric coating and the unique, inherent properties of the carbon nanotubes may allow for their future exploitation in the biomedical field. © 2011 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 49: 1389–1396, 2011     

Improving dispersion and integration of single‐walled carbon nanotubes in epoxy composites by using a reactive noncovalent dispersant

Uniform dispersion and strong interfacial interaction are two critical prerequisites for application of single‐walled carbon nanotubes (SWNTs) in polymer composites. To endow the composites with multifunctional feature, no damage on the chemical/electronic structure of SWNTs is also usually required. With these ends in view, two epoxide‐containing pyrene derivatives (EpPys) were designed, synthesized, and used as reactive noncovalent dispersants for developing multifunctional epoxy/SWNT composites. One having longer chain length between epoxide group and pyrene moiety, that is, EpPy‐16, shows higher dispersing efficiency and provides the nanotube dispersion with better stability, thus picking up for subsequent studies. Systematic characterization on SWNT/EpPy‐16 hybrid demonstrates that 13.2 wt % of EpPy‐16 is adsorbed on the SWNT surface through strong π‐stacking interaction, and intrinsic electronic structure of SWNTs is basically reserved. The solution‐based process adopted here preserves the good SWNT dispersing state in dispersion into the composites. Simultaneously, enhanced interfacial interaction is also realized by using EpPy‐16, which interacts noncovalently with SWNT but connects covalently to epoxy network. As a result, the composites acquire 37 and 22% increments in tensile strength and Young's modulus, respectively, relative to that of neat resin. A low‐electrical percolation threshold of 0.1 wt % SWNTs and improved thermal properties were also observed. © 2012 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2012     

Synthesis and characterization of single‐wall‐carbon‐nanotube‐doped emeraldine salt and base polyaniline nanocomposites

Nanocomposites of polyaniline (PANI) and single‐wall carbon nanotubes (SWNTs) were prepared and characterized via resonance Raman and electronic absorption spectroscopy (ultraviolet–visible/near‐infrared). The chemical synthesis of PANI was performed in the presence of SWNTs in concentrations ranging from 10 to 50 wt % (SWNT/PANI). The obtained materials were hydrophilic, homogeneous composite compounds. The chemical interaction between PANI (in the conducting emeraldine salt form and in the insulating emeraldine base form) and metallic and semiconducting nanotubes was investigated. The emeraldine salt form of the polymer was significantly stabilized in the composite in comparison with plain PANI. A selective electronic interaction process between PANI and metallic SWNTs was found. © 2005 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 43: 815–822, 2005     

“Click” coupling between alkyne‐decorated multiwalled carbon nanotubes and reactive PDMA‐PNIPAM micelles

Covalent functionalization of alkyne‐decorated multiwalled carbon nanotubes (MWNTs) with a well‐defined, azide‐derivatized, thermoresponsive diblock copolymer, poly(N,N‐dimethylacrylamide)‐poly(N‐isopropylacrylamide) (PDMA‐PNIPAM) was accomplished by the Cu(I)‐catalyzed [3 + 2] Huisgen cycloaddition. It was found that this reaction could simultaneously increase the molecular size and bonding density of grafted polymers when PDMA‐PNIPAM micelles were employed in the coupling system. On the other hand, attachment of molecularly dissolved unimers of high‐molecular weight onto the nanotube resulted in low‐graft density. The block copolymer bearing azide groups at the PDMA end was prepared by reversible addition–fragmentation transfer polymerization, which formed micelles with a diameter of ～40 nm at temperatures above its critical micelle temperature. Scanning electron microscopy was utilized to demonstrate that the coupling reaction was successfully carried out between copolymer micelles and alkyne‐bearing MWNTs. FTIR spectroscopy was utilized to follow the introduction and consumption of alkyne groups on the MWNTs. Thermogravimetric analysis indicated that the functionalized MWNTs consisted of about 45% polymer. Transmission electron microscopy was utilized to image polymer‐functionalized MWNTs, showing relatively uniform polymer coatings present on the surface of nanotubes. © 2008 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 46: 7187–7199, 2008     

Metallized nanotube polymer composites via supercritical fluid impregnation

Although many metal decorated nanotubes and nanowires appear in the literature, well‐dispersed metal decorated nanotube polymer composites have rarely been reported because of the excessive density mismatch between the decorated nanotubes and polymer matrix. Here, we report a novel method to prepare well‐dispersed, highly functional, metallized nanotube polymer composites (MNPCs) that possess remarkably improved electrical conductivity and mechanical toughness. The MNPCs are prepared by supercritical fluid impregnation of an organometal compound into a premade well‐dispersed single wall carbon nanotube‐polymer composite film. The infused precursor preferentially migrates towards the nanotubes to undergo spontaneous reduction and form nanometer‐scale metal particles leading to an increase in the conductivity of the MNPC films. The environmentally friendly supercritical fluid impregnation process significantly improved the toughness of the composite films, regardless of the presence of metal. Additional functionality can be imparted into the resulting MNPC by infusing other precursors such as magnetic and catalytic metal compounds. © 2011 Wiley Periodicals, Inc.* J Polym Sci Part B: Polym Phys, 2012     

Self‐Organizing Alignment of Carbon Nanotubes in Thermoplastic Polyurethane

Summary: A simple compounding technique for the fabrication of polymer nanocomposites with single‐walled carbon nanotubes having exceptional alignment and improved mechanical properties is described. The aligned‐nanotube composite was prepared by dissolving single‐walled carbon nanotubes in a solution of thermoplastic polyurethane and tetrahydrofuran. Solvent‐polymer interactions that induce the orientation of soft chain segments during the swelling and moisture curing stage are believed to serve as a driving force for the macroscopic alignment of the carbon nanotubes.

Alignment of single‐walled carbon nanotubes in thermoplastic polyurethane during polar solvent exposure.     

The effect of length of single‐walled carbon nanotubes (SWNTs) on electrical properties of conducting polymer–SWNT composites

DC conductivity of conjugated polymer‐single‐walled carbon nanotube (SWNT) composite films has been measured for different SWNT concentrations. The composite was prepared by dispersing SWNTs in the poly (3‐octylthiophene), P3OT matrix already dissolved in xylene. The conductivity of the composite films showed a rapid increase as the SWNT concentration increases beyond a certain value. This behavior is explained in terms of percolating paths provided by the SWNTs in the volume of polymer matrix. To investigate the effect of length of nanotubes on the percolation conductivity, different SWNT samples were employed with similar diameter but varying tube lengths. It was found that the conductivity of the composite films is strongly dominated by the length of the nanotubes. Lower percolation limit and high conductivity value of composite films is observed for longer nanotubes. Furthermore, the conductivity is observed to be dependent on the size of the host polymer molecule also. © 2009 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 48: 89–95, 2010     

Synthesis and characterization of pyrene bearing amphiphilic miktoarm star polymer and its noncovalent interactions with multiwalled carbon nanotubes

A novel amphiphilic miktoarm star polymer, polystyrene‐poly(ethylene glycol)‐poly(methyl methacrylate), bearing a pyrene group at the end of PS arm (Pyrene‐PS‐PEG‐PMMA) was successfully synthesized via combination of atom transfer radical polymerization and click chemistry. The structure and composition of the amphiphilic miktoarm star polymer were characterized by gel permeation chromatography and ¹H NMR. The functionalization of multiwalled carbon nanotubes (MWCNTs) via “π–π” stacking interactions with pyrene‐PS‐PEG‐PMMA miktoarm star polymer was accomplished and the resulting polymer‐MWCNTs hybrid was analyzed by using ¹H NMR, UV–vis, fluorescence spectroscopy, and thermal gravimetric analysis. The high‐resolution transmission electron microscopy and analytical techniques aforementioned confirmed that the noncovalent functionalization of MWCNT's with the amphiphilic miktoarm star polymer was successfully achieved. The MWCNT/pyrene‐PS‐PEG‐PMMA exhibited significant dispersion stability in common organic solvents such as dimethyl formamide, chloroform, and tetrahydrofuran. © 2012 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2012     

Matrix‐polymer‐functionalized multiwalled carbon nanotubes as a highly efficient toughening agent for matrix polymers

Matrix‐polymer‐functionalized multiwalled carbon nanotubes (MWCNTs) are demonstrated as a highly efficient toughening agent for matrix polymers. With poly(vinylidene fluoride) (PVDF) as the matrix polymer, the PVDF/MWCNT‐PVDF nanocomposite films show high toughness. With a small load amount of MWCNT‐PVDF (0.07 wt %), the nanocomposite film shows a yield point and a constant‐stress extension region in stress–strain tests, compared with the typical low‐extensibility feature of neat PVDF film. The PVDF/MWCNT‐PVDF‐0.7 film exhibits a 180‐fold increase of toughness and about 38‐fold increase in strain at break compared with neat PVDF film. This toughening effect is attributed to (a) homogeneous dispersion of MWCNT‐PVDF in PVDF, (b) the high efficiency of load‐transfer across MWCNT/PVDF interface, and (c) the long length of the MWCNTs. © 2012 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys, 2012     

Structure–property relationships in polyamide 6/multi‐walled carbon nanotubes nanocomposites

Polyamide 6 (PA6)/multi‐walled carbon nanotubes (MWCNT) nanocomposites were produced by diluting a masterbach containing 20 wt % nanotubes using melt mixing. The influence of the addition of well dispersed MWCNT (as indicated by scanning electron microscopy (SEM) and transmission electron microscopy (TEM)) on the thermal transitions, and crystallization behavior of the PA6 matrix is investigated. Differential scanning calorimetry (DSC) results show a reduction in heat capacity jump at the glass transition which is interpreted by an immobilized interfacial layer near the nanotubes. Furthermore, both DSC and X‐ray diffraction (XRD) measurements indicate that nanotubes favor the formation of the α crystalline form of PA6. These findings are correlated with the observed improvement of the storage modulus as revealed by dynamic mechanical thermal analysis (DMTA). Additionally, a new crystallization peak appears when MWCNT are added, and is attributed to the formation of a different morphology of the same type crystallite around the nanotubes walls (trans‐crystallinity). Finally, water sorption measurements show an increase of water content, normalized to the amorphous polymer fraction, in the nanocomposites. © 2009 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 47: 764–774, 2009     

Aspect ratio effects of multi‐walled carbon nanotubes on electrical,mechanical, and thermal properties of polycarbonate/MWCNT composites

Two multi‐walled carbon nanotubes (MWCNTs) having relatively high aspect ratios of 313 and 474 with approximately the same diameter were melt mixed with polycarbonate (PC) in a twin‐screw conical micro compounder. The effects of aspect ratio on the electrical, mechanical, and thermal properties of the PC/MWCNT composites were investigated. Electrical conductivities and storage moduli of the filled samples are found to be independent of the starting aspect ratio for these high aspect ratio tubes; although the conductivities and storage moduli are still significantly higher than values of composites made with nanotubes having more commercially common aspect ratios of ～100. Transmission electron microscopy results suggest that melt‐mixing reduces these longer nanotubes to the same length, but still approximately two times longer than the length of commercially common aspect ratio tubes after melt‐mixing. Molecular weight measurements show that during melt‐mixing the longer nanotubes significantly degrade the molecular weight of the polymer as compared to very similar nanotubes with aspect ratio ～100. Because of the molecular weight reduction glass transition temperatures predictably show a large decrease with increasing nanotube concentration. © 2013 Wiley Periodicals, Inc. J. Polym. Sci., Part B: Polym. Phys. 2014 , 52, 73–83     

Complementary effects of multiwalled carbon nanotubes and conductive carbon black on polyamide 6

This article introduces a newly innovative idea for preparation of superconductive ternary polymeric composites of polyamide 6 (PA6), conductive carbon black (CCB), and multiwalled carbon nanotubes (MWCNTs) with different weight ratios by a melt‐mixing technique. The complementary effects of CCB and MWCNTs at different compositions on rheological, physical, morphological, thermal, and dynamic mechanical and electrical properties of the ternary composites have been examined systematically. We have used a novel formulation to produce high‐weight fraction ternary polymer composites that show extremely higher conductivity when compared with their corresponding binary polymer composites at the same carbon loading. For example, with an addition of 10 wt % MWCNTs into the CCB/PA6 composite preloaded with 10 wt % CCB, the electrical conductivity of these ternary composites was about 5 S/m, which was 10 times that of the CCB/PA6 binary composite (0.5 S/m) and 125 times that of the MWCNT/PA6 binary composite (0.04 S/m) at 20 wt % carbon loading. The incorporation of the MWCNTs effectively enhanced the thermal stability and crystallization of the PA6 matrix in the CCB/PA6 composites through heterogeneous nucleation. The MWCNTs appeared to significantly affect the mechanical and rheological properties of the PA6 in the CCB/PA6 composites, a way notably dependent on the MWCNT contents. © 2010 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 48: 1203–1212, 2010     

The effect of molecular weight on the separation of semiconducting single‐walled carbon nanotubes using poly(2,7‐carbazole)s

The use of selective interactions between conjugated polymers and single‐walled carbon nanotubes has emerged as a promising method for the separation of nanotubes by electronic type. Although much attention has been devoted to investigating polyfluorenes and their ability to disperse semiconducting carbon nanotubes under specific conditions, other polymer families, such as poly(2,7‐carbazole)s, have been relatively overlooked. Poly(2,7‐carbazole)s have been shown to also preferentially interact with semiconducting carbon nanotubes, however a detailed investigation of polymer parameters, such as molecular weight, has not been performed. We have prepared seven different molecular weights of a poly(2,7‐carbazole), from short chain oligomers to high molecular weight polymers, and have investigated their effectiveness at dispersing semiconducting single‐walled carbon nanotubes. Although all polymer chain lengths were able to efficiently exfoliate carbon nanotube bundles using a mild dispersion protocol, only polymers above a certain threshold molecular weight (M_n ～ 27 kDa) were found to exhibit complete selectivity for semiconducting nanotubes, with no observable signals from metallic species. Additionally, we found the quality of separation to be strongly dependent on the ratio of polymer to carbon nanotube. Contrary to previous reports, we have found that an excess of poly(2,7‐carbazole) leads to incomplete removal of metallic carbon nanotubes. © 2015 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2015 , 53, 2510–2516     

“Click” generation of a conjugated polymer library for SWNT dispersion

Noncovalent functionalization of single‐walled carbon nanotubes (SWNTs) with conjugated polymers enhances SWNT processability and allows for selective dispersion of various SWNT species. Selective dispersions can be obtained by tuning the nature of the polymer, which can involve using various polymer backbones or side‐chains. However, a clear understanding of selectivity determinants is elusive, as the degree of polymerization (DP) has a large effect on SWNT selectivity. Additionally, preparing libraries of conjugated polymers with varying functionality while keeping DP consistent is difficult. Here, we report the utilization of a strained cyclooctyne‐containing conjugated polymer that serves as a versatile scaffold, enabling systematic preparation of a small library of conjugated polymers with different side‐chain functionality, while maintaining a consistent DP. The resulting polymers were used as dispersants for SWNTs, forming supramolecular polymer‐SWNT complexes that were characterized by UV‐Vis‐NIR absorption and Raman spectroscopy. In the series of polymers, we were able to probe the effect of small changes within the side chains, such as the incorporation of a carbonyl group or an aromatic unit, on the quality of the polymer‐SWNT dispersion. The results of these studies provide new insight into the factors that dictate the ability of a polymer to form strong interactions with SWNTs. © 2018 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2018 , 56, 2053–2058     

Small‐angle X‐ray scattering investigation of carbon nanotube‐reinforced polyacrylonitrile fibers during deformation

Structural changes during deformation in solution‐ and gel‐spun polyacrylonitrile (PAN) fibers with multi‐ and single‐wall carbon nanotubes (CNTs), and vapor‐grown carbon nanofibers were investigated using synchrotron X‐ray scattering. Previously published wide‐angle X‐ray scattering (WAXS) results showed that CNTs deform under load, alter the response of the PAN matrix to stress, and thus enhance the performance of the composite. In this article, we find that the elongated scattering entities that give rise to the small‐angle X‐ray scattering (SAXS) in solution‐spun fibers are the diffuse matrix‐void interfaces that follow the Porod's law, and in gel‐spun fibers these are similar to fractals. The observed smaller fraction of voids in the gel‐spun fibers accounts for the significant increase in the strength of this fiber. The degree of orientation of the surfaces of the voids is in complete agreement with those of the crystalline domains observed in WAXS, and increases reversibly upon stretching in the same way as those of the crystalline domains indicating that the voids are integral parts of the polymer matrix and are surrounded by the crystalline domains in the fibrils. The solution‐spun composite fibers have a larger fraction of the smaller (<10 nm) voids than the corresponding control PAN fibers. Furthermore, the size distribution of the voids during elongation changes greatly in the solution spun PAN fiber, but not so in its composites. The scattered intensity, and therefore the volume fraction of the voids, decreases considerably above the glass transition temperature (T_g) of polymer. Implications of these observations on the interactions between the nanotubes and the polymer are discussed. © 2009 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 47: 2394–2409, 2009     

Interaction of SWCNT and PPTA with sulfuric acid—Compatibilization of two materials in a common solvent

The results of a calorimetric study on the melting and crystallization behavior of concentrated sulfuric acid containing dispersed single wall carbon nanotubes (SWCNT), dissolved water, and dissolved poly‐p‐phenyleneterphthalate (PPTA) polymer are presented. The measured reduction of the heat of crystallization is caused by the build‐up of an associated layer of structured acid molecules around SWCNT and PPTA. The freezing point depression is related to the number of dissolved species such as ions. It is shown that this theory accurately describes the experimental data for dissolved water and sulfur trioxide, but not for large molecules such as SWCNT. A mechanism for the interaction between sulfuric acid and SWCNT is proposed, based on preferred adsorption of sulfur trioxide and dissociation of sulfuric acid, leading to an increased number of dissolved low‐molecular‐weight species. © 2008 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 46: 1914–1922, 2008     

Ionic liquid functionalized polylactide by cationic polymerization: Synthesis and stabilization of carbon nanotube suspensions

Medium molecular weight poly(L ,L ‐lactide)s (PLA) containing at one chain end ionic group derived from imidazolium ionic liquid (IL) were synthesized by cationic polymerization using hydroxylated IL as initiator. matrix assisted laser desorption/ionization time‐of‐flight analysis confirmed the structure of products (PLA‐IL). Carbon nanotubes (CNT) were dispersed in solution of PLA‐IL in 1,4‐dioxane and significant improvement of stability of suspension was observed by measurements of suspension absorbance. Similar effect was, however, observed also for solutions of PLA which did not contain terminal IL group. CNT samples treated with PLA‐IL and PLA were isolated, thoroughly washed with 1,4‐dioxane and stability of suspensions was again measured. Sample treated with PLA after washing behave similarly to untreated CNT. Stability of suspension of CNT treated with PLA‐IL after washing was considerably higher than that of untreated CNT and the presence of polymer bound to CNT was clearly detectable in scanning electron microscopy images. Results indicate that there is indeed an interaction between end‐group derived from IL and CNT surface as postulated earlier but to observe solely this effect an excess of polymer should be removed, otherwise factors such as increase of viscosity of solution or weak interactions of PLA ester groups with CNT may obscure results. © 2011 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2011