Influence of pressure on the properties of chromatographic columns. II. The column hold-up volume

The effect of the local pressure and of the average column pressure on the hold-up column volume was investigated between 1 and 400 bar, from a theoretical and an experimental point of view. Calculations based upon the elasticity of the solids involved (column wall and packing material) and the compressibility of the liquid phase show that the increase of the column hold-up volume with increasing pressure that is observed is correlated with (in order of decreasing importance): (1) the compressibility of the mobile phase (+1 to 5%); (2) in RPLC, the compressibility of the C18-bonded layer on the surface of the silica (+0.5 to 1%); and (3) the expansion of the column tube (<0.001%). These predictions agree well with the results of experimental measurements that were performed on columns packed with the pure Resolve silica (0% carbon), the derivatized Resolve-C18 (10% carbon) and the Symmetry-C18 (20% carbon) adsorbents, using water, methanol, or n-pentane as the mobile phase. These solvents have different compressibilities. However, 1% of the relative increase of the column hold-up volume that was observed when the pressure was raised is not accounted for by the compressibilities of either the solvent or the C18-bonded phase. It is due to the influence of the pressure on the retention behavior of thiourea, the compound used as tracer to measure the hold-up volume.     

Effect of the endcapping of reversed-phase high-performance liquid chromatography adsorbents on the adsorption isotherm

The retention mechanisms of n-propylbenzoate, 4-t ert-butylphenol, and caffeine on the endcapped Symmetry-C(18) and the non-endcapped Resolve-C(18) are compared. The adsorption isotherms were measured by frontal analysis (FA), using as the mobile phase mixtures of methanol or acetonitrile and water of various compositions. The isotherm data were modeled and the adsorption energy distributions calculated. The surface heterogeneity increases faster with decreasing methanol concentration on the non-endcapped than on the endcapped adsorbent. For instance, for methanol concentrations exceeding 30% (v/v), the adsorption of caffeine is accounted for by assuming three and two different types of adsorption sites on Resolve-C(18) and Symmetry-C(18), respectively. This is explained by the effect of the mobile phase composition on the structure of the C(18)-bonded layer. The bare surface of bonded silica appears more accessible to solute molecules at high water contents in the mobile phase. On the other hand, replacing methanol by a stronger organic modifier like acetonitrile dampens the differences between non-endcapped and endcapped stationary phase and decreases the degree of surface heterogeneity of the adsorbent. For instance, at acetonitrile concentrations exceeding 20%, the surface appears nearly homogeneous for the adsorption of caffeine.     

Comparison of the acidity of residual silanol groups in several liquid chromatography columns

The silanol acidity of Waters Resolve C18, Waters Resolve silica, Waters Symmetry C18, Waters Symmetry silica, Waters XTerra MS C18 and underivatized XTerra columns has been measured from the retention of LiNO3 with a methanol/water (60:40) mobile phase buffered to different pH values. The Li+ cation is retained by cationic exchange with the background cation of the mobile phase (Na+) through the ionized silanols. The number of active silanols increases in the order: XTerra MS C18 < Symmetry C18 < underivatized XTerra < Resolve C18 < Resolve silica approximately equal to Symmetry silica. XTerra MS C18 does not present any residual silanol acidity up to s(s)pH 10.0 (pH in 60% methanol) as measured by LiNO3. The underivatized XTerra packing and Symmetry C18 present active silanols only at s(s)pH values higher than 7.0. For the other three columns, two different types of silanols with different acidity (s(s)pKa values about 3.5-4.6 and 6.2-6.8, respectively) have been observed. Symmetry C18 shows evidence of the presence of active basic sites that retain NO3- by anionic exchange.     

Physical origin of peak tailing on C18-bonded silica in reversed-phase liquid chromatography

Single component isotherm data of caffeine and phenol were acquired on two different stationary phases for RPLC, using a methanol/water solution (25%, v/v, methanol) as the mobile phase. The columns were the non-endcapped Waters Resolve-C18, and the Waters XTerra MS C18. Both columns exhibit similar C18 -chain densities (2.45 and 2.50 micromol/m2) and differ essentially by the nature of the underivatized solid support (a conventional, highly polar silica made from water glass, hence containing metal impurities, versus a silica-methylsilane hybrid surface with a lower density of less acidic free silanols). Thirty-two adsorption data points were acquired by FA, for caffeine, between 10(-3) and 24 g/l, a dynamic range of 24,000. Twenty-eigth adsorption data points were acquired for phenol, from 0.025 to 75 g/l, a dynamic range of 3000. The expectation-maximization procedure was used to derive the affinity energy distribution (AED) from the raw FA data points, assuming a local Langmuir isotherm. For caffeine, the AEDs converge to a bimodal and a quadrimodal distribution on XTerra MS-C18 and Resolve-C18, respectively. The values of the saturation capacity (q(s,1) approximately equal to 0.80 mol/l and q(s,2) approximately equal to 0.10 mol/l) and the adsorption constant (b1 approximately equal to 3.11/mol and b2 approximately equal to 29.1 l/mol) measured on the two columns for the lowest two energy modes 1 and 2, are comparable. These data are consistent with those previously measured on an endcapped Kromasil-C18 in a 30/70 (v/v), methanol/water solution (q(s,1) = 0.9 mol/l and q(s,2) = 0.10 mol/l, b1 = 2.4 l/mol and b2 = 16.1 l/mol). The presence of two higher energy modes on the Waters Resolve-C18 column (q(s,3) approximately equal to 0.013 mol/l and q(s,4) approximately equal to 2.6 10(-4) mol/l, b3 approximately equal to 252 l/mol and b4 = 13,200 l/mol) and the strong peak tailing of caffeine are explained by the existence of adsorption sites buried inside the C18-bonded layer. It is demonstrated that strong interactions between caffeine and the water protected bare silica surface cannot explain these high-energy sites because the retention of caffeine on an underivatized Resolve silica column is almost zero. Possible hydrogen-bond interactions between caffeine and the non-protected isolated silanol groups remaining after synthesis amidst the C18-chain network cannot explain these high energy interactions because, then, the smaller phenol molecule should exhibit similarly strong interactions with these isolated silanols on the same Resolve-C18 column and, yet, the consequences of such interactions are not observed. These sites are more consistent with the heterogeneity of the local structure of the C18-bonded layer. Regarding the adsorption of phenol, no matter whether the column is endcapped or not, its molecular interactions with the bare silica were negligible. For both columns, the best adsorption isotherm was the Bilangmuir model (with q(s,1) approximately equal to 2 and q(s,2) approximately equal to 0.67 mol/l, b1 0.61 and b2 approximately equal to 10.3 l/mol). These parameters are consistent with those measured previously on an endcapped Kromasil-C18 column under the same conditions (q(s,1) = 1.5 and q(s,2) = 0.71 mol/l, b1 = 1.4 l/mol and b2 = 11.3 l/mol). As for caffeine, the high-energy sites are definitely located within the C18-bonded layer, not on the bare surface of the adsorbent.     

Chain conformation and solvent partitioning in reversed-phase liquid chromatography: Monte Carlo simulations for various water/methanol concentrations

Many structural models for the stationary phase in reversed-phase liquid chromatography (RPLC) systems have been suggested from thermodynamic and spectroscopic measurements and theoretical considerations. To provide a molecular picture of chain conformation and solvent partitioning in a typical RPLC system, a particle-based Monte Carlo simulation study is undertaken for a dimethyl octadecyl (C(18)) bonded stationary phase on a model siliceous substrate in contact with mobile phases having different methanol/water concentrations. Following upon previous simulations for gas-liquid chromatography and liquid-liquid phase equilibria, the simulations are conducted using the configurational-bias Monte Carlo method in the Gibbs ensemble and the transferable potentials for phase equilibria force field. The simulations are performed for a chain surface density of 2.9 micromol/m(2), which is a typical bonded-phase coverage for mono-functional alkyl silanes. The solvent concentrations used here are pure water, approximately 33 and 67% mole fraction of methanol and pure methanol. The simulations show that the chain conformation depends only weakly on the solvent composition. Most chains are conformationally disordered and tilt away from the substrate normal. The interfacial width increases with increasing methanol content and, for mixtures, the solvent shows an enhancement of the methanol concentration in a 10 Angstrom region outside the Gibbs dividing surface. Residual surface silanol groups are found to provide hydrogen bonding sites that lead to the formation of substrate bound water and methanol clusters, including bridging clusters that penetrate from the solvent/chain interfacial region all the way to the silica surface.     

Retention mechanism of poly(ethylene oxide) in reversed-phase and normal-phase liquid chromatography

The retention behavior of low- and high-molecular-mass poly(ethylene oxide) (PEO) in reversed-phase (RP) and normal-phase (NP) liquid chromatography was investigated. In RPLC using a C18 bonded silica stationary phase and an acetonitrile-water mixture mobile phase, the sorption process of PEO to the stationary phase showed deltaH(o) > 0 and deltaS(o) > 0. Therefore, PEO retention in RPLC separation is an energetically unfavorable, entropy-driven process, which results in an increase of PEO retention as the temperature increases. In addition, at the enthalpy-entropy compensation point the elution volume of PEO was very different from the column void volume. These observations are quite different from the RPLC retention behavior of many organic polymers. The peculiar retention behavior of PEO in RPLC separation can be understood in terms of the hydrophobic interaction of this class of typical amphiphilic compounds with the non-polar stationary phase, on the one hand, and with the aqueous mobile phase, on the other. The entropy gain due to the release of the solvated water molecules from the PEO chain and the stationary phase is believed to be responsible for the entropy-driven separation process. On the other hand, in NPLC using an amino-bonded silica stationary phase and an acetonitrile-water mixture mobile phase, PEO showed normal enthalpy-driven retention behavior: deltaH(o) < 0 and deltaS(o) < 0, with the retention decreasing with increasing temperature and PEO eluting near the column void volume at the enthalpy-entropy compensation point. Therefore, high-resolution temperature gradient NPLC separation of high-molecular-mass PEO samples can be achieved with relative ease. The molecular mass distribution of high-molecular-mass PEO was found to be much narrower than that measured by size-exclusion chromatography.     

Characterization of the acidity of residual silanol groups in immobilized artificial membranes

Residual silanol acidity and activity of one immobilized artificial membrane (IAM) column have been measured from the retention of LiNO(3) in the column with a methanol/buffer (1mM in Na(+)) (60:40, v/v) mobile phase buffered to different pH values. Just one type of silanol with pssK(a)=7.61 (near the pH limit recommended by the manufacturer) was found, although these silanols show large activity. The results obtained have been compared with those obtained previously for Resolve C18, Resolve Silica, Symmetry C18, Symmetry Silica, XTerra MS C18, underivatized XTerra, Lichrospher 100 RP-18, Purospher RP-18e, Luna C18 (2) and Chromolith Perfomance RP-18e, showing that the IAM column is similar to Luna C18 and Symmetry C18 in terms of silica quality, as measured by Li(+) retention. A warning about the use of IAM columns for emulation of biological systems at physiological pH 7 is given because the ionized silanols may contribute to the retention of some drugs at this pH.     

Retention mechanism of the multifunctional solute on columns with different coverage densities using highly aqueous reversed‐phase conditions

A series of 11 homemade octadecyl bonded phases with different coverage densities were tested to determine the influence of the stationary phase on the retention in highly aqueous mobile phases. The concentrations of the organic modifiers (methanol and ACN) were in the range of 0–20%_v/v. The coverage density of bonded ligands and the presence of the end‐capping have strong influence on the solute retention. Amoxicillin (AMO) was chosen as the test compound. Dual properties of AMO, which contain hydrophobic skeleton and polar groups (amino, hydroxyl and carbonyl), cause irregular changes of the retention over the stationary phase hydrophobicity and silanol activity at given mobile phase composition. Presented data show that application of non‐standard low coverage density C18 phases allow to determine AMO in the RPLC condition with high retention.     

Thermodynamics and kinetics of solute transfer in reversed-phase liquid chromatography

In this study, the thermodynamic and kinetic behavior of a homologous series of fatty acids is examined using a polymeric octadecylsilica stationary phase and a methanol mobile phase. The zone profiles are evaluated as the temperature is varied from 20 to 60 degrees C and the average pressure from 400 to 4570 p.s.i. (1 p.s.i.=6894.76 Pa). The rate constant for solute transfer from mobile to stationary phase (k(ms)) appears to be relatively constant with carbon number. In contrast, the rate constant from stationary to mobile phase (k(sm)) decreases logarithmically with increasing carbon number. This suggests that the mass transport processes become progressively slower, owing to the smaller diffusion coefficients of the larger solutes in the stationary phase. The activation energy decreases slightly in the mobile phase and increases slightly in the stationary phase with increasing carbon number. The activation energy in the stationary phase ranges from 41.6 to 55.9 kcal/mol, while the thermodynamic change in internal energy ranges from -9.8 to -29.0 kcal/mol for C10 to C22, respectively (1 cal=4.184 J). The activation volume increases with increasing carbon number in both the mobile and stationary phase. The activation volume in the stationary phase ranges from 31.7 to 211 cm3/mol, while the thermodynamic change in molar volume ranges from -27.1 to -104 cm3/mol for C10 to C22, respectively. These large changes in activation energy and volume suggest that the solutes do not enter and leave the stationary phase in a single step, but in a stepwise or progressive manner.     

Effect of the ionic strength of the solution and the nature of its ions on the adsorption mechanism of ionic species in RPLC III. Equilibrium isotherms and overloaded band profiles on Kromasil-C18

In two companion papers, we have described the influence of the concentration and the nature of completely dissociated salts dissolved in the mobile phase (methanol:water, 40:60, v/v) on the adsorption behavior of propranolol (R'-NH2+-R, Cl-) on XTerra-C18 and on Symmetry-C18. The same experiments were repeated on a Kromasil-C18 column to compare the adsorption behavior of this ionic compound on these three different RPLC systems. The adsorption data of propranolol hydrochloride were first measured by frontal analysis (FA) using a mobile phase without salt. These data fit best to the Bi-Moreau model. Large concentration band profiles of propranolol were recorded with mobile phases containing increasing KCl concentrations (0, 0.002, 0.005, 0.01, 0.05, 0.1 and 0.2 M) and the best values of the isotherm coefficients were determined using the numerical solution of the inverse problem of chromatography. The general effect of a dissociated salt in the mobile phase was the same as the one observed earlier with XTerra-C18 and Symmetry-C18. However, obvious differences were observed for the shape of the band profiles recorded at low column loading (1.5 g/L, 250 microL injected). A long shoulder is visible at all salt concentrations and the band broadening is maximum at low salt concentrations. A slow mass transfer kinetics on the high-energy sites of the bi-Moreau model might explain this original shape. Five other salts (NaCl, CsCl, KNO3, CaCl2 and Na2SO4) were also used at the same ionic strength (J = 0.2 M). As many different band profiles were observed, suggesting that specific solute-salt interactions take place in the adsorbed phase.     

System Maps for Retention of Small Neutral Compounds on a Superficially Porous Ethyl-Bridged,Octadecylsiloxane-Bonded Silica Stationary Phase in Reversed-Phase Liquid Chromatography

The system constants of the solvation parameter model are used to prepare system maps for the retention of small neutral compounds on an ethyl-bridged, ocatadecylsiloxane-bonded superficially porous silica stationary phase (Kinetex EVO C18) for aqueous mobile phases containing 10–70% (v/v) methanol or acetonitrile. Electrostatic interactions (cation-exchange) are important for the retention of weak bases with acetonitrile–water but not methanol–water mobile phase compositions. Compared with a superficially porous octadecylsiloxane-bonded silica stationary phase (Kinetex C18) with a similar morphology but different topology statistically significant differences in selectivity at the 95% confidence level are observed for neutral compounds that vary by size and hydrogen-bond basicity with other intermolecular interactions roughly similar. These selectivity differences are dampened with acetonitrile–water mobile phases, but are significant for methanol–water mobile phase compositions containing <30% (v/v) methanol. A comparison of a totally porous ethyl-bridged, octadecylsiloxane-bonded silica stationary phase (XBridge C18) with Kinetex EVO C18 indicated that they are effectively selectivity equivalent.     

醋酸水流动相体系中硅胶键合相上生物大分子保留行为的研究

 提出了以醋酸 水作为流动相的体系中 ,在ODS柱上分离生物大分子的反相高效液相色谱 (RPLC)方法。实验结果表明 ,醋酸 水的洗脱能力强于甲醇 水 三氟醋酸体系 ,在一定程度上克服了色谱分离中一些蛋白质的不可逆吸附且具有便于冷冻干燥的优点。用参数Z(1mol溶剂化溶质被溶剂化固定相吸附时从两者接触表面释放出置换剂的摩尔总数 ) ,logI(与 1mol溶质对固定相亲和势有关的常数 )和 j(与 1mol溶剂对固定相亲和势有关的常数 )对 9种蛋白质在此流动相体系中的保留进行了表征。     

氯甲基苯乙烯包夹硅基单柱强阴离子固定相的制备及应用

用氯甲基苯乙烯包夹硅胶基质制备出一种新型强阴离子色谱柱填料,该填料具有良好的色谱性能,可以较好地分离常见的一些无机阴离子;另外,该填料可以对油田中用作驱油剂的单、双石油磺酸盐进行较好的分离。     

Effect of the ionic strength of salts on retention and overloading behavior of ionizable compounds in reversed-phase liquid chromatography II. Symmetry-C18

In a companion paper, we describe the influence of the concentration and the nature of salts dissolved in the mobile phase (methanol:water, 40:60, v/v) on the adsorption behavior of propranolol (R'-NH2+ -R, Cl-) on XTerra-C18. The same experiments were repeated on a Symmetry-C18 column to compare the adsorption mechanisms of this ionic compound on these two very different RPLC systems. Frontal analysis (FA) measurements were first carried out to determine the best isotherm model accounting for the adsorption behavior of propranolol hydrochloride on Symmetry with a mobile phase without salt (and only 25% methanol to compensate for the low retention in the absence of salt). The adsorption data were best modeled by the bi-Moreau model. Large concentration band profiles of propranolol were recorded with mobile phases having increasing KCl concentrations (0, 0.002, 0.005, 0.01, 0.05, 0.1 and 0.2 M) and the best values of the isotherm coefficients were determined by the inverse method (IM) of chromatography. The general effect of a dissociated salt in the mobile phase was the same as the one observed earlier with XTerra-C18. Increasing the salt concentration increases the two saturation capacities of the adsorbent and the adsorption constant on the low-energy sites. The adsorption constant on the high-energy sites decreases and the adsorbate-adsorbate interactions tend to vanish with increasing salt concentration of the mobile phase. The saturation capacities decrease with increasing radius of the monovalent cation (Na+, K+, Cs+, etc.). Using sulfate as a bivalent anion (Na2SO4) affects markedly the adsorption equilibrium: the saturation capacities are drastically reduced, the high-energy sites nearly disappear while the adsorption constant and the adsorbate-adsorbate interactions on the low-energy sites increase strongly. The complexity of the thermodynamics in solution might explain the different influences of these salts on the adsorption behavior.     

Influence of stationary phase solvation on shape selectivity and retention in reversed-phase liquid chromatography

In the past few decades, shape selectivity has drawn a great deal of attention from chromatographers. The chemistry and characteristics of bonded stationary phases such as phase type, length of bonded phase, surface coverage, and silica surface material have an effect on the shape selectivity of the columns. Although the effects of bonded phase shape selectivity are relatively well understood, one remaining question is the effect of intercalated solvent on shape selectivity. The intercalation of organic modifier and water molecules into the stationary phase is believed to introduce more rigidity into bonded alkyl chains in RPLC. The use of gas chromatography (GC) opens a new dimension to approach this question. C18 columns 4 cm in length were prepared in our laboratory and used in both LC and GC experiments. Shape selectivity and thermodynamic constants for the transfer of a solute from the mobile phase to the stationary phase have been determined as a function of monomeric octadecyl stationary phase bonding densities over the range of 1.44-3.43 micromol/m2 and a polymeric phase (nominal surface coverage 4.77 micromol/m2). Comparing LC and GC experiments, we observed: (a) similar relationships between shape and phenyl selectivities with monomerically bonded C18 phase densities; (b) different correlation of thermodynamic quantities (DeltaH degrees , DeltaS degrees , and DeltaG degrees ) versus bonded phase densities. The effects of high temperature and residual silanol groups are sources of difficulty in elucidation of the intercalated mobile phase role in selectivity and retention for GC measurements.     

Insights into the Retention Mechanism for Small Neutral Compounds on Silica-Based Phenyl Phases in Reversed-Phase Liquid Chromatography

The system constants of the solvation parameter model are used to prepare system maps for the retention of small neutral compounds on phenylhexylsiloxane- and pentafluorophenylpropylsiloxane-bonded superficially porous silica stationary phases (Kinetex Phenyl-Hexyl and Kinetex F5) for aqueous mobile phases containing 10–70% (v/v) methanol or acetonitrile. Electrostatic interactions (cation exchange) are important for the retention of weak bases for acetonitrile–water mobile phases, but virtually absent for the same compounds for methanol–water mobile phases. The selectivity of the Kinetex Phenyl-Hexyl stationary phase for small neutral compounds is similar to an octadecylsiloxane-bonded silica stationary phase with similar morphology Kinetex C-18 for both methanol–water and acetonitrile–water mobile phase compositions. The Kinetex Phenyl-Hexyl and XBridge Phenyl stationary phases with the same topology but different morphology are selectivity equivalent, confirming that solvation of the interphase region can be effective at dampening selectivity differences for modern stationary phases. Small selectivity differences observed for XTerra Phenyl (different morphology and topology) confirm previous reports that the length and type of space arm for phenylalkylsiloxane-bonded silica stationary phases can result in small changes in selectivity. The pentafluorophenylpropylsiloxane-bonded silica stationary phase (Kinetex F5) has similar separation properties to the phenylhexylsiloxane-bonded silica stationary phases, but is not selectivity equivalent. However, for method development purposes, the scope to vary separations from an octadecylsiloxane-bonded silica stationary phase (Kinetex C-18) to “phenyl phase” of the types studied here is limited for small neutral compounds. In addition, selectivity differences for the above stationary phases are enhanced by methanol–water and largely suppressed by acetonitrile–water mobile phases. For bases, larger selectivity differences are possible for the above stationary phases if electrostatic interactions are exploited, especially for acetonitrile-containing mobile phases.     

Enhancement of selectivity in reversed-phase liquid chromatography

In an effort to gain insight into the relationship between stationary phase solvation and selectivity, the use of short- and medium-chained-length alcohols (methanol, n-propanol, n-butanol, and n-pentanol) as mobile phase modifiers in reversed-phase liquid chromatography (RPLC) was investigated to determine their impact on chromatographic selectivity. A wide range of mobile phase compositions was evaluated because of the large effect exerted by solvent strength on selectivity. Employing a set of six vanillin compounds as retention probes, evidence is presented to support the view that an increase in the hydrophobicity of the organic modifier used in RPLC can increase the selectivity of the C18 alkyl bonded phase while simultaneously decreasing the retention time of the eluting solutes. Thus, we are presented with an interesting paradox: higher selectivity and shorter retention times, which can be attributed to changes in either solvent selectivity and/or stationary phase solvation by the organic modifier.     

Adsorption mechanism in reversed-phase liquid chromatography. Effect of the surface coverage of a monomeric C18-silica stationary phase

The effect of the bonding density of the octadecyl chains onto the same silica on the adsorption and retention properties of low molecular weight compounds (phenol, caffeine, and sodium 2-naphthalene sulfonate) was investigated. The same mobile phase (methanol:water, 20:80, v/v) and temperature (T = 298 K) were applied and two duplicate columns (A and B) from each batch of packing material (neat silica, simply endcapped or C1 phase, 0.42, 1.01, 2.03, and 3.15 micromol/m2 of C18 alkyl chains) were tested. Adsorption data of the three compounds were acquired by frontal analysis (FA) and the adsorption energy distributions (AEDs) were calculated using the expectation-maximization method. Results confirmed earlier findings in linear chromatography of a retention maximum at an intermediate bonding density. From a general point of view, the saturation capacity of the adsorbent tends to decrease with increasing bonding density, due to the vanishing space intercalated between the C18 bonded chains and to the decrease of the specific surface area of the stationary phase. The equilibrium constants are maximum for an intermediary bonding density (approximately 2 micromol/m2). An enthalpy-entropy compensation was found for the thermodynamic parameters of the isotherm data. Weak equilibrium constants (small deltaH) and high saturation capacities (large deltaS) were observed at low bonding densities, higher equilibrium constants and lower saturation capacities at high bonding densities, the combinations leading to similar apparent retention in RPLC. The use of a low surface coverage column is recommended for preparative purposes.     

An assessment of the retention behaviour of polycyclic aromatic hydrocarbons on reversed phase stationary phases--thermodynamic behaviour on C18 and phenyl-type surfaces

The thermodynamic retention behaviour of a linear series of polycyclic aromatic hydrocarbons (PAHs) was investigated on C18 and selected phenyl-type reversed-phase stationary phases, namely C18, C18 Aqua, Propyl-phenyl and Synergi polar-RP stationary phases, using methanol mobile phases. The Propyl-phenyl stationary phase, despite having the lowest surface coverage, was found to exhibit significantly larger enthalpic interactions to the other Phenyl-type phase (Synergi polar-RP) even though this had a much higher surface coverage. This indicated that stronger interactions between the PAHs and the stationary phase ligands were occurring on the Propyl-phenyl phase. Evaluation of the elution band profile of the PAHs in the aqueous methanol mobile phase revealed fairly symmetrical bands for the C18, C18 Aqua and Synergi polar-RP, but severe peak tailing on the Propyl-phenyl phase. A change in mobile phase from methanol to acetonitrile improved the peak shape of the PAHs on the Propyl-phenyl phase, leading to the assumption that unfavourable pi-pi interactions were occurring between the electron-rich PAHs and the electron-rich phenyl rings of the Propyl-phenyl phase.     

High-performance liquid chromatography of sulfonamides and quinolones on p-tert-butyl-calix[6]arene-bonded silica gel stationary phase

The high-performance liquid chromatographic behavior of some sulfonamides and quinolones was studied on a p-tert-butyl-calix[6]arene-bonded silica gel stationary phase. The effect of mobile phase variables such as methanol content, ionic strength and pH on their chromatographic behavior was investigated. The retention behavior of sulfonamides on the stationary phase was compared with that on both Zorbax C₁₈-bonded silica gel and γ-(ethylenediamino)propyltriethoxylsilane-bonded silica gel (diamino-bonded phase). The retention mechanism of sulfonamides and quinolones on the stationary phase was also discussed. The results indicate that the stationary phase behaves as a reversed-phase packing and its separation selectivity is much better than that of not only Zorbax C₁₈ phase but also diamino-bonded phase. Some sulfonamides and quinolones were separated on the stationary phase, but the separation of sulfonamides is far more successful.