Eu3+掺杂SiO2-Al2O3-B2O3玻璃制备及光谱性能研究

高温溶制了Eu^3＋掺杂SiO2-Al2O3-B2O3-MxOy（M=Li^＋,Na^＋,K^＋,Mg^2＋,Ca^2＋,Sr^2＋,RE^3＋）硼硅酸盐玻璃,测试了玻璃样品的发射光谱、激发光谱和透射光谱,研究了不同碱金属离子、碱土金属离子对该系统荧光性能的影响。利用发射光谱计算了Ω2,Ω4以及^5D0到^7F2,^7F4的自发辐射几率和振子强度f（^5D0→^7F2）,f（^5D0→^7F4）。结果表明,材料的发射能级为^5D0→^7F1（590nm）,^5D0→^7F2（617nm）,^5D0→^7F4（698nm）,而且材料的结构对称性越差,跃迁戒律打破地越彻底,荧光发射越强。     

CaO-SiO2-B2O3:Sm2O3玻璃的合成及Sm3+发光性质研究

用常规的高温合成法合成了CaO-SiO2-B2O3Sm2O3玻璃, 探讨了玻璃的最佳合成温度、玻璃的吸收光谱, 并研究了其发光性质. 在CaO-SiO2-B2O3Sm2O3玻璃体系中观察到了Sm3+的发射光谱. 样品的发射光谱有3个主要荧光发射峰, 峰值波长分别为568, 605, 650 nm, 其中最强峰为605 nm,可见发射起源于Sm3+离子4f电子的f-f跃迁. 其中568 nm对应于4G5/2→6H5/2跃迁、 605 nm对应于4G5/2→6H7/2跃迁、 650 nm对应于4G5/2→6H9/2跃迁, 光谱性质表明这种玻璃体系能够把太阳光中的紫外光转换成红光, 从而增强红光的发射强度. 可以利用这些玻璃的发光性质来制备农用转光玻璃.     

共压共烧结法制备固体氧化物燃料电池及其结构性能分析

用共压 共烧结法制备以Ce0.8Gd0.2O1.9(CGO)作电解质的中温固体氧化物燃料电池,其中CGO和阴极材料La0.6Sr0.4Co0.2Fe0.8O3-α(LSCF)由溶胶凝胶法合成.实验表明,,由共压 共烧结法制备的上述材料组装的电池具有致密的电解质层,且与电极的结合非常紧密,测得的最大输出功率0.14W/cm2,相应的操作温度为650℃,电流密度为307mA/cm2.该电池的电化学过程为内阻和浓差极化联合控制,使用造孔剂可改善阳极基底的孔隙结构,降低浓差极化过电位.     

Eu3+掺杂Y2O3-Al2O3-SiO2玻璃的制备与荧光性能研究

采用高温熔融法制备了Eu³⁺掺杂Y₂O₃-Al₂O₃-SiO₂荧光玻璃,探讨了成分对该体系玻璃形成能力的影响,并对不同Eu³⁺掺杂浓度下的荧光性能进行了研究.结果表明,熔融温度为1500℃条件下,SiO₂含量对该体系的玻璃形成能力影响明显,Y/Al摩尔比为3/5时,SiO₂含量在52%-68%(摩尔分数)范围内时可以获得玻璃.掺杂Eu³⁺的Y₂O₃-Al₂O₃-SiO₂玻璃具有荧光性能,在395nm波长激发下,在588 nm和614 nm处出现明显的发射峰.随着Eu³⁺掺杂浓度的增加,该荧光玻璃的发射波长不变,但发射强度有所变化;当Eu³⁺掺杂浓度为1.5%(摩尔分数)时,特征发射峰强度最大.     

Sm3+杂CaO-SiO2-B2O3发光玻璃的制备、表征及性质

用高温固相法合制备了以CaO-SiO2-B2O3为基质,Sm3+为激活离子的发光玻璃.对Sm3+的淬灭浓度、基质中的硼硅比例、其他稀土离子的敏化作用以及基质组成等因素对玻璃发光特性的影响进行了探讨,并用红外和X-衍射分析对样品的结构进行了表征.结果表明:当Sm3+掺杂的物质的量分数为1.2%,激发波长λ=404 nm时,玻璃体60CaO-20SiO2-20B2O3:1.2Sm3+的发光强度为4838 A.U.(λ=606 nm);这种发光玻璃具有将紫外及近紫外光转换为橙红色光的特点.少量的Eu3+的掺入,对玻璃体的发光起敏化作用;玻璃体中的组分CaO可被ZnO替代.     

Thermal study of the influence of chemical bond ionicity on the glass transformation in (Na2O, CaO, MgO)-Al2O3-SiO2 glasses

The relation between change of the specific heat (ΔC _p) accompanying the glass transformation and the chemical composition of glasses (Na₂O, CaO, MgO)-Al₂O₃-SiO₂ system has been studied. The exchange of modifiers in the glass structure causes the ΔC _p increase in the sequence Na>Ca>Mg. Change the glass network composition by introducing Al into it makes smaller increase of the ΔC _p values. It has been shown that degree of ΔC _p value changes is dependent on the iconicity/covalence of chemical bonds of cations with oxygen of glass structure network. This revised version was published online in July 2006 with corrections to the Cover Date.     

Pr1－xSrxAlO3－δ的合成及其作为固体氧化物燃料电池阴极的性能研究

采用固相反应法合成了一系列样品Pr_1－xSr_xAlO_3－δ (x＝0, 0.05, 0.1, 0.2, 0.3, 0.4, 0.5). XRD结果表明, Sr在A位上的固溶度约为20%; 利用交流阻抗法测量了样品的电导率, 结果表明, 电导率随着Sr掺入量的增加而增大, Pr_0.8Sr_0.2AlO_3－δ的电导率最大, 在850 ℃达到0.02 S/cm; 离子迁移数的测试结果说明, Pr_1－xSr_xAlO_3－δ为离子电子混合导体; 考察了它们作为固体氧化物燃料电池(SOFCs)阴极的性能, 极化曲线和阻抗的测试结果表明, 阴极性能随着Sr掺入量的增加而提高; 阴极稳定性测试结果表明, 在测量时间范围内, 阴极过电位随时间缓慢下降.     

Preparation of La2O3-TiO2-SiO2 Inorganic-Organic Hybrid Materials and Their Optical Properties

Inorganic-organic hybrid materials in La₂O₃-TiO₂-SiO₂ system were prepared from La(NO₃)₃, titanium tetraisopropoxide, and silicon alkoxides. Ternary transparent materials prepared from glycidyloxypropyltrimethoxysilane (GPTS) were obtained in a wide composition region (La₂O₃ 50 mol%, TiO₂ 40 mol%). Hybrid materials prepared using methyltrimethoxysilane (MTMS) at MTMS/TMOS = 1 were transparent in the composition of La₂O₃ 30 mol% and TiO₂ 25 mol%. La(NO₃)₃ crystallines or TiO₂ small particles were precipitated in translucent materials. La₂O₃ content strongly affected the bulk density compared with TiO₂ content. Absorption edge of the hybrid materials was shifted to longer wavelength as TiO₂ and La₂O₃ contents increased. Partial coefficient of refractive index for the three metal oxides increased in the order SiO₂ < TiO₂ < La₂O₃ for both hybrid materials.     

RE2O3-Al2O3-SiO2玻璃连接氮化硅合成复相陶瓷的研究

采用Ｙ２Ｏ３－Ａｌ２Ｏ３－ＳｉＯ２－Ｘ稀土玻璃进行氮化硅复相陶瓷的连接。用四点弯曲方法测定不同连接工艺下的连接强度。并对连接界面进行ＳＥＭ、ＥＰＭＡ和ＸＲＤ分析。液相钎料玻璃在界面上与氮化硅反应，形成氮化硅／Ｓｉ２Ｎ２Ｏ／Ｙ（Ｌａ）－Ｓｉａｌｏｎ玻璃／Ｙ（Ｌａ）－Ｓｉａｌｏ玻璃的梯度层界面。接头强度随着保温时间、妆温度的增加，先增后。 在ＹＡＳ钎料中添加氧化镧，可以提高接头的高温强度。ＬａＹＯ３的     

银基陶瓷复合电极的电性能及其在固体氧化物燃料电池中的应用

银基陶瓷复合电极可望在中低温固体氧化物燃料电池(SOFCs)、含碳燃料SOFCs和固体氧化物电解池(SOECs)中得到广泛应用。为优选出银基陶瓷复合电极的成分,本研究采用YSZ(钇稳定化氧化锆)电解质,先将Ag-YSZ和Ag-GDC(掺钆氧化铈)材料制备成对称电极,测试其在空气下的阻抗谱,由此判断其作为阴极的性能;发现在相同的Ag含量时, Ag-YSZ的阴极极化电阻普遍低于Ag-GDC;当Ag的质量分数为65%时, Ag-YSZ的极化电阻最低,而对于Ag-GDC, Ag的质量分数是70%。然后采用空气中极化电阻最低的Ag-YSZ和Ag-GDC作为电极制备了SOFC单电池,并采用加湿氢气燃料对电池的电化学性能进行了测试。根据电池的阻抗谱数据,将极化阻抗的数值减去上述阴极阻抗的数值可得到阳极阻抗值,其结果和电池的输出特性均表明, Ag-GDC作为阳极的性能优于Ag-YSZ,即在本实验条件下, Ag-YSZ更适合用作阴极,而Ag-GDC更适合用作阳极。本研究不仅提供了关于银基复合电极材料的有用数据,还提供了一种测试SOFC阳极极化电阻的方法。     

掺Eu的SiO2-B2O3体系和SiO2-B2O3-Na2O体系的结构及Eu3+的发光性质

采用溶胶-凝胶技术制备了掺Eu3+的以SiO2-B2O3和SiO2-B2O3-Na2O为基质的玻璃态发光材料. 通过激发光谱、发射光谱研究了Eu3+的发光性质, 通过红外光谱、 TEM 、 XRT进一步研究了基质结构变化对发光性能的影响. 结果显示 材料经 600 ℃退火处理后, 结构已十分稳定. 在588 nm和613 nm处显示弱的Eu3+的特征发射光谱, 对应于Eu3+的5D0-7Fj(j=1,2)跃迁. 以SiO2-B2O3为基质的玻璃材料的红外光谱显示形成了Si-O-B键. 该结构对Eu3+的发光有严重的淬灭作用, 使Eu3+的发光强度大大减弱. 以SiO2-B2O3-Na2O为基质的玻璃材料显示Eu3+的发光增强, 红外光谱显示不存在Si-O-B键的振动吸收. 可能是Na取代B的位置, 形成了Si-O-Na键. 此结构对Eu3+的发光有一定增加作用.     

Improvement of multi-layer anode for direct ethanol Solid Oxide Fuel Cells

Anodes for Solid Oxide Fuel Cells (SOFCs) that are capable of directly using hydrocarbon fuels without external reforming have been of great interest in the recent years. We have fabricated a two-layer structure containing a Cu–CeO₂ catalyst layer by tape casting and screen printing technology. The interface combination between the Cu–CeO₂ catalyst layer and the Ni–YSZ-supported anode issues importantly for the stability of the anode structure. In this paper, a Ni–CeO₂ interlayer was added between these two layers to improve the long-term stability of the multi-layer anode. Meanwhile, the exit gas of the single cell was also analyzed by a gas chromatographer (GC) to determine the reaction mechanism of the ethanol fuel in the anode.     

平板式氧化物燃料电池（SOFC）研制及性能考察

对固体氧化物燃料电池进行研制。在ＹＳＺ固体电解质上制备成功Ｌａ０．８Ｓｒ０．２ＭｎＯ３阴极和Ｎｉ－ＹＳＺ陶瓷阳极，并解决了高温无机密封技术难题，组装出平板式ＬＳＭ．ＹＳＺ．Ｎｉ－ＹＳＺ单电池。     

Preparation of Cr2O3-Al2O3 Solid Solutions by Reactive Magnetron Sputtering

 (Al,Cr)₂O₃ layers were deposited on cemented carbide insert tips at a substrate temperature of 500 °C by means of reactive magnetron sputtering. An Al target was sputtered in RF mode and a Cr target in DC mode simultaneously in an oxygen/argon plasma. The influence of the Al and Cr sputter power and of the oxygen partial pressure on composition and structure of the (Al,Cr)₂O₃ layers as well as on the binding states of their components were investigated. Special attention was paid to the interpretation of the O ls and O-KLL fine structure and peak shifts. For the binary phases γ-Al₂O₃ and Cr₂O₃, a good agreement with literature values was observed in each case. In case of the ternary phases a continuous shift of the energetic position of the O1s peak, the O-KL₂₃L₂₃ transition and the modified Auger parameter α ′ of oxygen between the two binary phases γ-Al₂O₃ and Cr₂O₃ could be detected, indicating a wide range of solid solubility between Al₂O₃ and Cr₂O₃. As revealed by grazing incidence X-ray diffraction, the crystallinity of the ternary phases is less pronounced as compared to the binaries and increases with increasing oxygen flow rate.     

催化精馏专用填料型固体酸SO42-/ZrO2-Al2O3-Al的研究

为了研制催化精馏专用催化剂,采用铝阳极氧化法制备了Al2O3-Al一体型载体,并将活性固体超强酸SO42-/ZrO2引入到Al2O3-Al上,得到一种新型催化精馏专用填料式固体酸SO42-/ZrO2-Al2O3-Al催化剂.利用XRD、 SEM、 BET、 XPS、 NH3-TPD等手段对其进行了表征.结果表明,所制得的阳极氧化铝膜厚为56 μm, SO42-/ZrO2-Al2O3-Al固体酸具有比表面积大、酸强度适中的特点.XRD结果表明, ZrO2在Al2O3-Al上处于高度分散状态.将该固体酸用于乙酸/乙醇酯化反应中,显示出较高的催化活性,且稳定性较好.     

氧化铜与CeO2-γ-Al2O3混合氧化物载体之间的表面相互作用

 采用XRD，XPS和TPR等手段研究了氧化铜与二氧化铈－氧化铝机械混合载体之间的表面相互作用．结果表明，在混合载体表面，当氧化铜的负载量低于其在二氧化铈载体上的分散容量时，氧化铜优先与二氧化铈发生作用并分散在其表面；当氧化铜的负载量超过其在二氧化铈载体上的分散容量时，氧化铜会继续在氧化铝表面分散．这些结果说明，在制备用氧化铈改性载体的负载型催化剂时，如果氧化铈的用量偏高，会导致样品中有晶相氧化铈生成，从而对氧化铈作为改性剂的作用不利．     

Electrochemical Study of Glasses in the System Na2O-B2O3

The steady-state electrical conductivity and microhardness of glasses in the system Na₂O-B₂O₃ was studied. IR spectroscopy was applied to determine the content of impurity hydrogen in the glasses studied.     

阴极支撑Ni-YSZ/YSZ/LSM-YSZ固体氧化物电解池制氢性能研究

利用固体氧化物电解池(Solid oxide electrolysis cell,SOEC)在高温下电解水蒸气制氢,被认为是未来的大规模制氢方法之一.本文采用干压法和丝网印刷法制备了SOEC,考察了氢电极气氛和工作温度对SOEC电解性能的影响,测试了SOEC的稳定性.实验结果表明:氢电极进气中适宜的水蒸气含量为70%～80%;电解池在800,850和900℃,1.50 V的产氢速率分别为89,163和243 N·ml·cm-2·h-1;在900℃以0.33 A·cm-2恒流电解2 h,电解电压的稳定值为0.98 V,并且电解池运行稳定,无明显衰减.阻抗谱解析表明,电极过程是整个电解池电极反应的速度控制步骤.     

Chemical Properties of the K2O-Al2O3-SiO2-P2O5 System Activated with Mn(II) Oxide

Synthesis and some chemical properties of the Al₂O-SiO₂-P₂O₅ system activated with MnO were studied.