编辑部按语

氧化物电阻变换(resistance switching)是发现已经超过40年的物理现象,即在外加电压或脉冲下氧化物器件的电阻下降并可以在外加电压或脉冲下翻转恢复。因为不丢失电阻存储器的可能应用,氧化物电阻变换近年得到了十分广泛的关注。由于多种多样氧化物材料和器件的实验带来了不同的测量数据,目前提出了很多假说来解释观察到的氧化物电阻变换行为,其中大多数文章使用了氧空位扩散形成导电细丝的模型。该文章"氧化物电阻变换与自束缚载流子"利用不同研究小组发     

基于类耿氏效应的低密度聚乙烯中空间电荷包行为的模拟仿真

低密度聚乙烯材料中的空间电荷包现象通常会引起严重电场畸变而影响其击穿特性. 本文借鉴半导体中的耿氏效应的负微分迁移率机理来描述电荷包的形成机理,并结合载流子的注入条件及体内陷阱对电荷迁移的影响等因素,对文献中报道的两类外加场强不同且迁移趋势各异的空间电荷包行为进行了模拟仿真,模拟的电荷包大小随电场变化规律,电荷包迁移速率随时间变化规律等与相应实验结果符合.模拟结果表明,产生耿氏效应的负微分迁移率是造成电荷包非弥散传输的主要原因,其与材料电极注入情况及体内陷阱态的共同作用导致了空间电荷包行为迁移的多样性. 关键词： 空间电荷包 耿氏效应 模拟仿真 负微分迁移率     

Au/SrTiO3/Au界面电阻翻转效应的低频噪声分析

本文研究了Au/SrTiO₃/Au三明治结构中的双极电阻翻转效应, 观察到高、低阻态的电阻弛豫现象. 低频噪声测量表明高、低阻态的电阻涨落表现出1/f行为. 对比试验表明, 高阻态的低频噪声来源于反向偏置肖特基势垒和氧空位的迁移, 强度较大, 低阻态的噪声则源于类欧姆接触底电极区域的氧空位迁移导致的载流子涨落, 强度较低. 同时, 界面上氧空位浓度的弛豫导致了高、低阻态的弛豫过程. 关键词： 电阻翻转效应 低频噪声 氧空位     

聚乙烯空间电荷包行为的形成机理与仿真方法研究

聚乙烯中的空间电荷包行为是空间电荷的一种特殊的输运行为.研究表明,空间电荷包行为由于受材料本身特性、外加电场大小以及环境温度等的影响,导致其产生过程及传输特性上存在较大差异,这些因素给空间电荷包行为产生机理研究带来了较大困难.通过对电荷的电极注入过程、载流子的体内迁移规律及空间电荷与体内陷阱的相互作用机制进行分析,探讨了不同外加电场及不同深度陷阱能级对电荷包行为造成的相关影响,在此基础上建立物理模型来描述电荷包的产生和迁移过程.模型中提出了在高于阈值电场时,载流子迁移速度与电场关系存在负微分迁移率的假设.基于此模型对空间包行为的模拟结果与实验结果取得较好的一致. 关键词： 空间电荷包 数值模拟 负微分迁移率     

考虑空间电荷层效应的氧离子导体电解质内载流子传输特性

晶界或异质界面诱发的空间电荷层(space charge layer,SCL)效应,被认为是氧离子导体电解质内界面附近区域载流子传输特性显著区别于体相区域的关键原因之一.现有研究多采用Poisson-Boltzmann(PB)方程预测SCL效应的影响规律,但其基于载流子电化学平衡假设,无法用于载流子存在宏观运动的工况,极大限制了相关传输机理研究.本文耦合Poisson方程和载流子质量守恒方程,建立了适用于载流子具有宏观运动时氧离子导体内载流子传输过程的模型,推导了控制SCL效应的关键无量纲参数.聚焦固体氧化物燃料电池中常用的AO2-M2O3氧离子导体电解质,对比研究了传统PB方程和本文建立的Poisson-载流子质量守恒耦合方程的预测结果可靠性.进一步采用耦合模型深入分析了考虑SCL效应时氧离子导体内部氧空位传输机理,发现导体界面电流密度增大导致SCL电阻先减小后增大.增大无量纲Debye长度(表征空间电荷层厚度与导体厚度的比值)可显著增大SCL电阻.当驱动氧空位移动的过电势与热势数量级相当时,增大无量纲电势(表征过电势与热势的比值)导致SCL电阻增大;当过电势远小于热势时,改变无量纲电势对氧空位传输过程几乎无影响.本文研究结论可为通过合理设计晶界或异质界面以改善氧离子导体内载流子传输能力及最终提高相关电化学器件性能提供理论依据.     

单层密集ZnO纳米棒阻变器件的导电机制

制备了一种具有多级存储效应的密集ZnO纳米棒阵列阻变存储器件,借助I-V曲线和荧光光谱分析了器件的电流传导机制和阻变机制,发现器件在不同的电阻态下分别属于欧姆传导和空间电荷限制电流( SCLC)传导机制。正向电场作用使纳米棒表面耗尽区的氧空位V++密度增大,完善了电子传输的导电细丝通道,器件实现了由高阻态向低阻态的转变;在反向电压作用下,导电通道断裂,器件恢复到高阻态。     

无注入型发光二极管的载流子输运模型研究

无载流子注入型发光二极管(简称无注入型LED)因其简单的器件结构有望应用于Micro-LED、纳米像元发光显示等新型微显示技术.由于没有外部载流子注入,无注入型LED的内部载流子输运行为无法直接用传统的PN结理论进行描述.因此,建立无注入型LED的载流子输运模型对于理解其工作机理和提高器件性能具有重要意义.本文根据无注入型LED的器件结构,结合PN结理论建立无注入型LED的载流子输运数学模型.基于该数学模型解释器件的工作原理,获得器件的载流子输运特性,揭示感应电荷区长度、内部PN结压降与外加驱动电压频率的关系.根据建立的数学模型提出了针对无注入型LED器件设计的建议:1)减小感应电荷区掺杂浓度,可有效提高内部LED的压降;2)利用PN结的隧穿效应,可有效提高器件内部LED的压降;3)使用正负方波驱动可以获得比正弦驱动更大的内部LED压降.本文有关无注入型LED的载流子输运模型的研究有望为改善无注入型LED器件结构、优化工作模式提供理论指导.     

Ti/HfO2/Pt阻变存储单元中的氧空位聚簇分布

为了研究阻变存储器导电细丝的形成位置和分布规律, 使用X射线光电子能谱研究了Ti/HfO₂/Pt阻变存储器件单元中Hf 4f的空间分布, 得到了阻变层的微结构信息. 通过I-V测试, 得到该器件单元具有典型的阻变特性; 通过针对Hf 4f的不同深度测试, 发现处于低阻态时, 随着深度的增加, Hf⁴⁺化学组分单调地减小; 而处于高阻态和未施加电压前, 该组分呈现波动分布; 通过Hf⁴⁺在高阻态和低阻态下组分含量以及电子能损失谱分析, 得到高阻态下Hf⁴⁺组分的平均含量要高于低阻态; 另外, 高阻态和低阻态下的O 1s谱随深度的演变也验证了Hf⁴⁺的变化规律. 根据实验结果, 提出了局域分布的氧空位聚簇可能是造成这一现象的原因. 空位簇间的链接和断裂决定了导电细丝的形成和消失. 由于导电细丝容易在氧空位缺陷聚簇的地方首先形成, 这一研究为导电细丝的发生位置提供了参考.     

迁移率对单层有机发光器件中电场与载流子分布的影响

有机发光器件的宏观特性与有机层中的电场和载流子浓度分布密切相关。建立的有机电致发光器件模型是由两个金属电极中间夹一层有机发光薄膜材料组成的单层器件,金属与有机发光层之间为欧姆接触。模型以载流子运动的扩散-漂移理论为基础,利用数值方法研究了有机发光层中双极载流子注入时的电势、电场、载流子浓度和复合密度分布。分析结果表明:当两种载流子的迁移率相同时,电场强度、载流子浓度、复合密度的分布呈对称形式。而当电子和空穴的迁移率μn和μp相差比较大时,高迁移率的载流子不仅仅分布在注入端附近而且还有一小部分能够传输到另一端,而低迁移率的载流子只分布在其注入端附近;当μn、μp的大小相差不大时,载流子传输情况就介于两者之间。当μn/μp的比值变化时,电场强度的极大值向载流子迁移率小的注入端偏移。     

硅太阳能电池的调制载流子红外辐射动态响应与参数分析

建立了调制激光诱发硅太阳能电池的少数载流子密度波数学模型,并利用光致载流子辐射检测掺杂浓度、阻抗及载流子输运参数. 对频域响应曲线中的双弯曲效应进行了研究,构建了小交流信号作用的太阳能电池等效电路拓扑结构,仿真分析了不同掺杂浓度、阻抗电阻和载流子传输参数对频响曲线拐点的影响. 通过光致载流子辐射频域扫描实验与多参数拟合检测了单晶硅太阳电池的施/受主浓度、并联电阻和载流子输运参数. 结果表明：光致载流子辐射技术检测大面积太阳能电池频响曲线的双弯曲是由电容效应所引起的,建立的数学模型可定量描述和预测检测结果,并用于测量太阳能电池的掺杂浓度、电阻和载流子输运参数. 关键词： 调制自由载流子辐射 扫频检测 PN结电容 参数测量     

Guided-Wave Two-Dimensional Acousto-Optic Scanner Using Proton-Exchanged Lithium Niobate Waveguide

Two-dimensional scanning of a 0.6328 mum guided-light beam has been realized using noncolinear acousto-optic (AO) coplanar Bragg diffraction together with colinear AO guided-mode to substrate radiation-mode conversion in a Z-cut Xpropagation LiNbO3 proton-exchanged (PE) waveguide. The two surface acoustic (SAW) waves utilized are at the center frequencies of 500 and 200 MHz, propagating in the Y and X axes, respectively. Two-dimensional scanning of approximately 720 resolvable light beam spots, namely, 18 40 (horizontal vertical) scanning, has been demonstrated using a light beam of 1.0 mm aperture. The total number of resolvable beam spots can be greatly increased from 720 by simply utilizing SAW transducers of larger bandwidth and a light beam of greater aperture. It should also be possible to significantly increase the diffraction efficiency from 3 % by optimizing the parameters of the PE waveguide and the SAWs.     

Effect ofγ-radiation on the spectral luminescence characteristics of impure cadmium tungstate crystals

Results of a study of the effect of γ-radiation on the spectral luminescence properties of cadmium tungstate crystals doped with silver, bismuth, and molybdenum cations are presented. Spectral characteristics of the nondnnnoped crystals are briefly described. Absorption and photo and X-ray luminescence spectra of the crystals taken before and after exposure to γ-radiation (5.5·10⁴ Gy) are compared. It is found that the spectral characteristics of the crystals doped with silver, bismuth, and molybdenum cations do not change markedly after the exposure. The relation between the type of impurity-induced defects, individual characteristics of the impurity cations, and the character of the effect of γ-radiation on the spectral luminescence properties of impure crystals is analyzed (preliminarily). Translated from Zhurnal Prikladnoi Spektroskopii, Vol. 64, No. 1, pp. 55–60, January–February, 1997.     

Femtosecond Transform-Limited Pulse Generation by Compensating for the Linear Chirp of SPM Spectra in Dispersion Shifted Fibers

A simple technique of pulse compression, based on the linear chirp compensation of self-phase modulation (SPM) spectra in dispersion shifted fibers, is demonstrated. The optimization procedure is carried out, for a short span of a single-mode fiber, using a parabolic law, which describes the behavior of the squared output pulse width versus the pump peak power in the case of Gaussian pulses. The experimental results give a minimum pulse duration of 233 fs, which is in good agreement with the model. Shorter and coherent pulses, down to 90 fs, have been obtained by inserting an interference filter at the optical output.     

Sorting of bending magnets for the SSRF booster

The Shanghai Synchrotron Radiation Facility(SSRF)booster ring,a full energy injector for the storage ring,is deigned to accelerate the electron beam energy from 150MeV to 3.5GeV that demands high extraction efficiency at the extraction energy with low beam loss rate when electrons are ramping.Closed orbit distortion(COD)caused by bending magnet field uniformity errors which affects the machine performance harmfully could be effectively reduced by bending magnet location sorting.Considering the affections of random errors in measurement,both ideal sorting and realistic sorting are studied based on measured bending magnet field uniformity errors and one reasonable combination of bending magnets which can reduce the horizontal COD by a factor of 5is given as the final installation sequence of the booster bending magnets in this paper.     

Measurement of nonlinear coefficient of optical fiber based on small chirped soliton transmission

We measure the waveform and phase curves of short optical pulses before and after transmission over different lengths of fibers by use of the pulse analyzer with the frequency-resolved optical gating (FROG),and numerically simulate pulse evolution under the experimental conditions.The nonlinear coefficient of the fiber is given by comparing the experimental results with the numerical ones.Difference between the experiment and numerical simulation is analyzed.     

Resonance scattering of canonical elastic shells in absorbing fluid medium

Resonance scattering of elastic spherical shell and cylindrical shell while the surrounding fluid medium has absorption is studied. The normal mode solution derived using exact elastic theory and the separation of variables is still applicable. However, the scattering form function has to be modified for the absorbing medium, otherwise the unreasonable result would be obtained. The backscattering form function in the absorbing medium is redefined, and the form function of elastic spherical and cylindrical shell with vacuum or solid matter filled is calculated in various absorption conditions. The results show that the absorption of surrounding fluid leads to notable attenuation of the coincidence resonances in the mid-frequency, but it has a little influence on the low-frequency resonance scattering induced by the filler inside the shell.     

Single-beam self-referenced phase-sensitive surface plasmon resonance sensor with high detection resolution

A versatile and low-cost single-beam self-referenced phase-sensitive surface plasmon resonance(SPR)sensing system with ultra-high resolution performance is presented.The system exhibits a root-mean-square phase fluctuation of ±0.0028.over a period of 45 min.i.e.a resolution of±5.2×10-9 refractive index units.The enhanced performance has been achieved through the incorporation of three design elements:a true single-beam configuration enabling complete self-referencing so that only the phase change associated with SPR gets detected,a differential measurement scheme to eliminate spurious signals not related to the sensor response,and the elimination of retardation drifts by incorporating temperature stabilization in the liquid crystal phase modulato .Our design should bring the detection sensitivity of non-labeling SPR biosensing closer to that achievable by conventional fluorescence-based techniques.     

Influences of SiO2 protective layers and annealing on the laser-induced damage threshold of Ta2O5 films

Ta2O5 films are prepared on BK7 substrates with conventional electron beam evaporation deposition.The effects of SiO2 protective layers and annealing on the laser-induced damage threshold (LIDT) of the films are investigated.The results show that SiO2 protective layers exert little influence on the electric field intensity(EFI)distribution,microstructure and microdefect density but increase the absorption slightly.Annealing iS effective on decreasing the microdefect density and the absorption of the films.Both SiO2 protective layers and annealing are beneficial to the damage resistance of the films and the latter is more effective to improve the LIDT.Moreover,the maximal LIDT of Ta2O5 films is achieved by the combination of SiO2 protective layers and annealing.     

A stereo matching algorithm using multi-peak candidate matches and geometric constraints

Gray cross correlation matching technique is adopted to extract candidate matches with gray cross correla- tion coefficients less than some certain range of maximal correlation coefficient called multi-peak candidate matches. Multi-peak candidates are extracted corresponding to three closest feature points at first. The corresponding multi-peak candidate matches are used to construct the model polygon. Correspondence is determined based on the local geometric relations between the three feature points and the multi-peak candidates. The disparity test and the global consistency checkout are applied to eliminate the remaining ambiguous matches that are not removed by the local geometric relational test. Experimental results show that the proposed algorithm is feasible and accurate.