深亚微米器件沟道长度对总剂量辐照效应的影响

研究了180 nm 互补金属氧化物半导体技术下的器件沟道长度对总剂量辐照效应的影响. 在其他条件如辐照偏置、器件结构等不变的情况下, 氧化层中的陷阱电荷决定了辐照响应. 浅沟槽隔离氧化层中的陷阱电荷使得寄生的侧壁沟道反型, 从而形成大的关态泄漏电流. 这个电流与沟道长度存在一定的关系, 沟道长度越短, 泄漏电流越大. 首次发现辐照会增强这个电流的沟道长度调制效应, 从而使得器件进一步退化.     

部分耗尽结构绝缘体上硅器件的低频噪声特性

针对部分耗尽结构绝缘体上硅(silicon-on-insulator, SOI)器件低频噪声特性展开实验与理论研究. 实验结果表明, 器件低频噪声主要来源于SiO₂-Si界面附近缺陷态对载流子的俘获与释放过程; 基于此理论可提取前栅和背栅氧化层界面附近缺陷态密度分别为8×10¹⁷ eV^-1·cm^-3和2.76×10¹⁷ eV^-1·cm^-3. 基于电荷隧穿机理, 在考虑隧穿削弱因子、隧穿距离与时间常数之间关系的基础上, 提取了前、背栅氧化层内缺陷态密度随空间的分布情况. 此外, SOI器件沟道电流归一化噪声功率谱密度随沟道长度的增加而线性减小, 这表明器件低频噪声主要来源于沟道的闪烁噪声. 最后, 基于电荷耦合效应, 分析了背栅电压对前栅阈值电压、沟道电流以及沟道电流噪声功率谱密度的影响.     

超深亚微米PMOS器件的NBTI退化机理

对超深亚微米PMOS器件的负栅压温度不稳定性(NBTI)退化机理进行了研究.主要集中在对器件施加NBT和随后的PBT应力后器件阈值电压的漂移上.实验证明反型沟道中空穴在栅氧中的俘获以及氢分子在栅氧中的扩散是引起NBTI退化的主要原因.当应力条件变为PBT时，陷落的空穴可以快速退陷，但只有部分氢分子可以扩散回栅氧与衬底界面钝化硅悬挂键，这就导致了PBT条件下阈值电压只能部分恢复. 关键词： 超深亚微米PMOS器件 负偏压温度不稳定性 界面陷阱 氢气     

工艺偏差下PMOS器件的负偏置温度不稳定效应分布特性

当器件特征尺寸进入纳米级,负偏置温度不稳定性(NBTI)效应和工艺偏差都会导致p型金属氧化层半导体(PMOS)器件性能和可靠性的下降.基于反应-扩散(R-D)模型,本文分析了工艺偏差对NBTI效应的影响;在此基础上将氧化层厚度误差和初始阈值电压误差引入到R-D模型中,提出了在工艺偏差下PMOS器件的NBTI效应统计模型.基于65 nm工艺,首先蒙特卡罗仿真表明在工艺偏差和NBTI效应共同作用下,PMOS器件阈值电压虽然会随着应力时间增大而沿着负方向增加,但是阈值电压的匹配性却随着时间推移而变好;其次验证本文提出的统计模型准确性,以R-D模型为参考,在10~4s应力时间内,PMOS器件阈值电压退化量平均值和均方差的最大相对误差分别为0.058%和0.91%;最后将此模型应用到电流舵型数模转换器中,仿真结果显示在工艺偏差和NBTI效应共同作用下,数模转换器的增益误差会随着应力时间的推移而增大,而线性误差会逐渐减小.     

NBT导致的深亚微米PMOS器件退化与物理机理

研究了深亚微米PMOS器件在负偏压温度(negative bias temperature, NBT) 应力前后的电流电压特性随应力时间的退化，重点分析了NBT应力对PMOS器件阈值电压漂移的影响，通过实验证明了在栅氧化层和衬底界面附近的电化学反应和栅氧化层内与氢相关的元素的扩散，是PMOS器件中NBT效应产生的主要原因.指出NBT导致的PMOS器件退化依赖于反应机理和扩散机理两种机理的平衡. 关键词： 深亚微米PMOS器件 负偏压温度不稳定性 界面态 氧化层固定正电荷     

量子阱Si/SiGe/Sip型场效应管阈值电压和沟道空穴面密度模型

Si材料中较低的空穴迁移率限制了Si互补金属氧化物半导体器 件在高频领域的应用. 针对SiGe p型金属氧化物半导体场效应管(PMOSFET)结构, 通过求解纵向一维泊松方程,得到了器件的纵向电势分布, 并在此基础上建立了器件的阈值电压模型,讨论了Ge组分、缓冲层厚度、 Si帽层厚度和衬底掺杂对阈值电压的影响.由于SiGe沟道层较薄, 计算中考虑了该层价带势阱中的量子化效应. 当栅电压绝对值过大时, 由于能带弯曲和能级分裂造成SiGe沟道层中的空穴会越过势垒到达Si/SiO₂界面, 从而引起器件性能的退化. 建立了量子阱SiGe PMOSFET沟道层的空穴面密度模型, 提出了最大工作栅电压的概念, 对由栅电压引起的沟道饱和进行了计算和分析. 研究结果表明,器件的阈值电压和最大工作栅压与SiGe层Ge组分关系密切, Ge组分的适当提高可以使器件工作栅电压范围有效增大.     

高场应力及栅应力下AlGaN/GaN HEMT器件退化研究

采用不同的高场应力和栅应力对AlGaN/GaN HEMT器件进行直流应力测试,实验发现：应力后器件主要参数如饱和漏电流,跨导峰值和阈值电压等均发生了明显退化,而且这些退化还是可以完全恢复的;高场应力下,器件特性的退化随高场应力偏置电压的增加和应力时间的累积而增大;对于不同的栅应力,相对来说,脉冲栅应力和开态栅应力下器件特性的退化比关态栅应力下的退化大.对不同应力前后器件饱和漏电流,跨导峰值和阈值电压的分析表明,AlGaN势垒层陷阱俘获沟道热电子以及栅极电子在栅漏间电场的作用下填充虚栅中的表面态是这些不同应 关键词： AlGaN/GaN HEMT器件 表面态(虚栅) 势垒层陷阱 应力     

多晶SiGe栅量子阱pMOSFET阈值电压模型

本文基于多晶SiGe栅量子阱SiGe pMOSFET器件物理,考虑沟道反型时自由载流子对器件纵向电势的影响,通过求解泊松方程,建立了p+多晶SiGe栅量子阱沟道pMOS阈值电压和表面寄生沟道开启电压模型.应用MATLAB对该器件模型进行了数值分析,讨论了多晶Si_1-yGe_y栅Ge组分、Si_1-xGe_x量子阱沟道Ge组分、栅氧化层厚度、Si帽层厚度、沟道区掺杂浓度和 关键词： 多晶SiGe栅 寄生沟道 量子阱沟道 阈值电压     

15 nm Bulk nFinFET器件性能研究及参数优化

为研究Bulk FinFET工作时基本结构参数、器件温度和栅极材料对其性能的影响,建立了一个15 nm n型Bulk FinFET器件模型,仿真分析了不同栅长、鳍宽、鳍高、沟道掺杂浓度、器件工作温度、栅极材料对器件性能的影响,发现增长栅长、降低鳍宽和增加鳍高有助于抑制短沟道效应;1×10¹⁷ cm^-3以下的低沟道掺杂浓度对器件特性影响不大,但高掺杂会使器件失效;器件工作温度的升高会导致器件性能的下降;采用高K介质材料作为栅极器件性能优于传统材料SiO₂。     

绝缘体上硅金属氧化物半导体场效应晶体管中辐射导致的寄生效应研究

基于⁶⁰Co γ射线源研究了总剂量辐射对绝缘体上硅（silicon on insulator,SOI）金属氧化物半导体场效应晶体管器件的影响.通过对比不同尺寸器件的辐射响应,分析了导致辐照后器件性能退化的不同机制.实验表明：器件的性能退化来源于辐射增强的寄生效应;浅沟槽隔离（shallow trench isolation,STI）寄生晶体管的开启导致了关态漏电流随总剂量呈指数增加,直到达到饱和;STI氧化层的陷阱电荷共享导致了窄沟道器件的阈值电压漂移,而短沟道器件的阈值电压漂移则来自于背栅阈值耦合;在同一工艺下,尺寸较小的器件对总剂量效应更敏感.探讨了背栅和体区加负偏压对总剂量效应的影响,SOI器件背栅或体区的负偏压可以在一定程度上抑制辐射增强的寄生效应,从而改善辐照后器件的电学特性.     

Guided-Wave Two-Dimensional Acousto-Optic Scanner Using Proton-Exchanged Lithium Niobate Waveguide

Two-dimensional scanning of a 0.6328 mum guided-light beam has been realized using noncolinear acousto-optic (AO) coplanar Bragg diffraction together with colinear AO guided-mode to substrate radiation-mode conversion in a Z-cut Xpropagation LiNbO3 proton-exchanged (PE) waveguide. The two surface acoustic (SAW) waves utilized are at the center frequencies of 500 and 200 MHz, propagating in the Y and X axes, respectively. Two-dimensional scanning of approximately 720 resolvable light beam spots, namely, 18 40 (horizontal vertical) scanning, has been demonstrated using a light beam of 1.0 mm aperture. The total number of resolvable beam spots can be greatly increased from 720 by simply utilizing SAW transducers of larger bandwidth and a light beam of greater aperture. It should also be possible to significantly increase the diffraction efficiency from 3 % by optimizing the parameters of the PE waveguide and the SAWs.     

Effect ofγ-radiation on the spectral luminescence characteristics of impure cadmium tungstate crystals

Results of a study of the effect of γ-radiation on the spectral luminescence properties of cadmium tungstate crystals doped with silver, bismuth, and molybdenum cations are presented. Spectral characteristics of the nondnnnoped crystals are briefly described. Absorption and photo and X-ray luminescence spectra of the crystals taken before and after exposure to γ-radiation (5.5·10⁴ Gy) are compared. It is found that the spectral characteristics of the crystals doped with silver, bismuth, and molybdenum cations do not change markedly after the exposure. The relation between the type of impurity-induced defects, individual characteristics of the impurity cations, and the character of the effect of γ-radiation on the spectral luminescence properties of impure crystals is analyzed (preliminarily). Translated from Zhurnal Prikladnoi Spektroskopii, Vol. 64, No. 1, pp. 55–60, January–February, 1997.     

Femtosecond Transform-Limited Pulse Generation by Compensating for the Linear Chirp of SPM Spectra in Dispersion Shifted Fibers

A simple technique of pulse compression, based on the linear chirp compensation of self-phase modulation (SPM) spectra in dispersion shifted fibers, is demonstrated. The optimization procedure is carried out, for a short span of a single-mode fiber, using a parabolic law, which describes the behavior of the squared output pulse width versus the pump peak power in the case of Gaussian pulses. The experimental results give a minimum pulse duration of 233 fs, which is in good agreement with the model. Shorter and coherent pulses, down to 90 fs, have been obtained by inserting an interference filter at the optical output.     

Sorting of bending magnets for the SSRF booster

The Shanghai Synchrotron Radiation Facility(SSRF)booster ring,a full energy injector for the storage ring,is deigned to accelerate the electron beam energy from 150MeV to 3.5GeV that demands high extraction efficiency at the extraction energy with low beam loss rate when electrons are ramping.Closed orbit distortion(COD)caused by bending magnet field uniformity errors which affects the machine performance harmfully could be effectively reduced by bending magnet location sorting.Considering the affections of random errors in measurement,both ideal sorting and realistic sorting are studied based on measured bending magnet field uniformity errors and one reasonable combination of bending magnets which can reduce the horizontal COD by a factor of 5is given as the final installation sequence of the booster bending magnets in this paper.     

Measurement of nonlinear coefficient of optical fiber based on small chirped soliton transmission

We measure the waveform and phase curves of short optical pulses before and after transmission over different lengths of fibers by use of the pulse analyzer with the frequency-resolved optical gating (FROG),and numerically simulate pulse evolution under the experimental conditions.The nonlinear coefficient of the fiber is given by comparing the experimental results with the numerical ones.Difference between the experiment and numerical simulation is analyzed.     

Resonance scattering of canonical elastic shells in absorbing fluid medium

Resonance scattering of elastic spherical shell and cylindrical shell while the surrounding fluid medium has absorption is studied. The normal mode solution derived using exact elastic theory and the separation of variables is still applicable. However, the scattering form function has to be modified for the absorbing medium, otherwise the unreasonable result would be obtained. The backscattering form function in the absorbing medium is redefined, and the form function of elastic spherical and cylindrical shell with vacuum or solid matter filled is calculated in various absorption conditions. The results show that the absorption of surrounding fluid leads to notable attenuation of the coincidence resonances in the mid-frequency, but it has a little influence on the low-frequency resonance scattering induced by the filler inside the shell.     

Single-beam self-referenced phase-sensitive surface plasmon resonance sensor with high detection resolution

A versatile and low-cost single-beam self-referenced phase-sensitive surface plasmon resonance(SPR)sensing system with ultra-high resolution performance is presented.The system exhibits a root-mean-square phase fluctuation of ±0.0028.over a period of 45 min.i.e.a resolution of±5.2×10-9 refractive index units.The enhanced performance has been achieved through the incorporation of three design elements:a true single-beam configuration enabling complete self-referencing so that only the phase change associated with SPR gets detected,a differential measurement scheme to eliminate spurious signals not related to the sensor response,and the elimination of retardation drifts by incorporating temperature stabilization in the liquid crystal phase modulato .Our design should bring the detection sensitivity of non-labeling SPR biosensing closer to that achievable by conventional fluorescence-based techniques.     

Influences of SiO2 protective layers and annealing on the laser-induced damage threshold of Ta2O5 films

Ta2O5 films are prepared on BK7 substrates with conventional electron beam evaporation deposition.The effects of SiO2 protective layers and annealing on the laser-induced damage threshold (LIDT) of the films are investigated.The results show that SiO2 protective layers exert little influence on the electric field intensity(EFI)distribution,microstructure and microdefect density but increase the absorption slightly.Annealing iS effective on decreasing the microdefect density and the absorption of the films.Both SiO2 protective layers and annealing are beneficial to the damage resistance of the films and the latter is more effective to improve the LIDT.Moreover,the maximal LIDT of Ta2O5 films is achieved by the combination of SiO2 protective layers and annealing.     

A stereo matching algorithm using multi-peak candidate matches and geometric constraints

Gray cross correlation matching technique is adopted to extract candidate matches with gray cross correla- tion coefficients less than some certain range of maximal correlation coefficient called multi-peak candidate matches. Multi-peak candidates are extracted corresponding to three closest feature points at first. The corresponding multi-peak candidate matches are used to construct the model polygon. Correspondence is determined based on the local geometric relations between the three feature points and the multi-peak candidates. The disparity test and the global consistency checkout are applied to eliminate the remaining ambiguous matches that are not removed by the local geometric relational test. Experimental results show that the proposed algorithm is feasible and accurate.