超大规模集成电路互连电迁移自由体积电阻模型

将晶核析出的Avrami 方程应用于描述超大规模集成电路中金属Al薄膜互连电迁移过程中电阻的演变. 根据电子散射理论，晶界电阻主要起源于晶界处空位或者空洞对电子的散射. 为了描述这些离子的特征，引入了自由体积的概念，将晶界处电子散射这个复杂的过程简化用自由体积的有效散射截面来描述，从而建立了自由体积与电阻变化的定量关系，统一描述了电迁移过程中不同阶段的电阻变化. 数值模拟结果表明，在第一个空洞成核时刻电阻会发生急剧变化，这一结果已被实验所证实. 关键词： 电迁移 Al互连 电阻变化     

金属互连电迁移噪声的相关维数研究

针对金属铝互连中噪声信号随电迁移过程变化规律及其所反映的内部失效机理问题，提出将相关维数用于对电迁移噪声时间序列的分析.通过对互连电迁移噪声实验数据的相关维数计算，发现随着电迁移的进行，金属铝互连噪声由随机性成分占主导变为确定性成分占主导，反映出噪声由随机信号转变为混沌动力学信号.应用散射理论解释上述现象，在金属互连电迁移中，空位扩散阶段噪声主要产生机制是空位随机散射；在空位聚集到空洞成核这一过程中，噪声产生机制逐渐从随机散射转变到弹道混沌腔输运机制为主.通过与传统表征参量的对比，证明相关维数可用于预测金 关键词： 电迁移 噪声 相关维数 混沌     

金属互连电迁移噪声的多尺度熵复杂度分析

针对传统频域方法用于分析金属铝互连中的噪声信号的局限性,本文采用多尺度熵方法分析电迁移噪声时间序列.结果表明在电迁移早期,噪声信号较不规律,复杂度较大;随空洞成核的发生,噪声信号规律性增强,复杂度明显减小,反映出随电迁移过程的进行系统的混乱度不断减小.通过与传统表征参量的对比,证明多尺度熵能够对电迁移失效过程进行表征. 关键词： 电迁移 噪声 多尺度熵 复杂度     

金属薄膜电迁移1/f噪声与1/f2噪声统一模型

应用晶粒边界自由体积的概念建立了能够统一描述金属薄膜1f噪声与1f2噪声的模型.该模型表明,结构完整的多晶金属薄膜产生的电噪声为1f噪声,当金属薄膜受到电迁移损伤而形成空洞时就会引入1f2噪声的成分.在电迁移应力实验中,观察到金属薄膜1fγ噪声在空洞成核前γ约为10,一旦发生空洞成核,即突增至16以上,这一规律与本模型的预测相符合 关键词： 金属薄膜 1fγ噪声 电迁移 自由体积     

非高斯噪声激励下FitzHugh-Nagumo神经元系统的随机共振

研究了乘性非高斯噪声和加性高斯白噪声共同激励下FitzHugh-Nagumo(FHN) 神经元系统的随机共振问题. 利用路径积分法和两态模型理论, 推导出系统信噪比的表达式. 研究结果表明: 系统参数在不同的取值条件下, FHN神经元模型出现了随机共振和双重随机共振现象. 此外, 非高斯参数q在不同的取值条件下, 乘性噪声强度和加性噪声强度对信噪比的影响是不同的. 非高斯噪声的加入有利于增强FHN神经元系统的信号响应.     

n型金属氧化物半导体场效应晶体管噪声非高斯性研究

基于n型金属氧化物半导体场效应晶体管（nMOSFET）噪声的数涨落模型,采用高阶统计量双相干系数平方和研究了nMOSFET噪声的非高斯性.通过对nMOSFET实际测试噪声的分析,发现nMOSFET器件噪声存在非高斯性;小尺寸器件噪声的非高斯性强于大尺寸器件;在器件的强反型线性区,其非高斯性随着漏压的增加而增加.文中还通过蒙特卡罗模拟和中心极限定理理论对nMOSFET噪声的非高斯性作了深入的探讨. 关键词： 噪声 非高斯性 n型金属氧化物半导体场效应晶体管 氧化层陷阱     

非高斯噪声激励下含周期信号FitzHugh-Nagumo系统的响应特征

研究了非高斯噪声激励下含周期信号的FHN模型的动力学行为. 通过计算神经元的平均响应时间、观察神经元的共振活化和噪声增强稳定现象,分析了非高斯噪声对神经元动力学行为的影响. 发现通过改变非高斯噪声的相关时间可以有效地改变共振活化和噪声增强稳定现象. 观察到在强相关噪声下不同强度的非高斯噪声抑制了神经元的噪声增强稳定现象而共振活化现象几乎不变,也就是非高斯噪声有效地增强了神经响应的效率. 观察了平均响应时间与非高斯噪声参数q之间的关系,当q为一个有限的小于1的值时,平均响应时间取得最小值. 最后表明在一定条件下,非高斯噪声出现重尺度现象,即非高斯噪声产生的效果可以由高斯白噪声来估计. 关键词： FHN神经系统 非高斯噪声 平均响应时间 共振活化现象     

金属互连电迁移噪声的分形特征

为了研究金属互连电迁移失效机理并寻找新的电迁移表征参量，应用分形理论，通过电子扩散轨迹分形维数，将电迁移噪声时间序列分形维数与晶粒间界分形维数相联系，确定了噪声时间序列分形维数在电迁移演变中的变化趋势.研究结果表明，在金属互连电迁移前期，晶粒间界形貌越来越复杂，致使噪声时间序列的分形维数逐渐增大；成核后，由于空位凝聚成空洞，晶粒间界形貌变得较成核前规则，致使噪声时间序列的分形维数减小；成核时刻是其折点.实验结果证明理论分析的正确性，噪声时间序列的分形维数可望作为金属互连电迁演变的表征参量.     

基于多域特征提取和深度学习的声源被动测距*

由于实际海洋环境中存在大量的非高斯噪声,一些基于高斯假设的传统去噪方法在实际海洋环境中性能下降甚至失效。针对非高斯噪声,如α稳定分布噪声、非平稳行船噪声下的脉冲信号的去噪与重构,该文提出一种基于深度学习的方法。去噪模型首先通过学习带噪信号短时傅里叶变换谱与残差谱之间的映射关系以去除环境噪声,之后对去噪信号的时频谱进行逆变换重构脉冲信号。仿真实验结果表明,深度学习模型在非高斯噪声环境下脉冲信号的去噪与重构任务中有着良好的表现,在实测样本上也表现出良好的泛化性,体现了一定的工程应用价值。     

考虑界面散射的金属纳米线热导率修正

理论分析了声子和电子输运对Cu, Ag金属纳米线热导率的贡献. 采用镶嵌原子作用势模型描述纳米尺寸下金属原子间的相互作用, 应用平衡分子动力学方法和Green-Kubo函数模拟了金属纳米线的声子热导率; 采用玻尔兹曼输运理论和Wiedemann-Franz定律计算电子热导率; 并通过散射失配模型和Mayadas-Shatzkes模型引入晶界散射的影响. 在此基础上, 考察分析了纳米线尺度和温度的影响. 研究结果表明: Cu, Ag纳米线热导率的变化规律相似; 电子输运对金属纳米线的导热占主导地位, 而声子热导率的贡献也不容忽视; 晶界散射导致热导率减小, 尤其对电子热导率作用显著; 纳米线总热导率随着温度的升高而降低; 随着截面尺寸减小而减小, 但声子热导率所占份额有所增加. 关键词： 纳米线 热导率 表面散射 晶界散射     

Guided-Wave Two-Dimensional Acousto-Optic Scanner Using Proton-Exchanged Lithium Niobate Waveguide

Two-dimensional scanning of a 0.6328 mum guided-light beam has been realized using noncolinear acousto-optic (AO) coplanar Bragg diffraction together with colinear AO guided-mode to substrate radiation-mode conversion in a Z-cut Xpropagation LiNbO3 proton-exchanged (PE) waveguide. The two surface acoustic (SAW) waves utilized are at the center frequencies of 500 and 200 MHz, propagating in the Y and X axes, respectively. Two-dimensional scanning of approximately 720 resolvable light beam spots, namely, 18 40 (horizontal vertical) scanning, has been demonstrated using a light beam of 1.0 mm aperture. The total number of resolvable beam spots can be greatly increased from 720 by simply utilizing SAW transducers of larger bandwidth and a light beam of greater aperture. It should also be possible to significantly increase the diffraction efficiency from 3 % by optimizing the parameters of the PE waveguide and the SAWs.     

Femtosecond Transform-Limited Pulse Generation by Compensating for the Linear Chirp of SPM Spectra in Dispersion Shifted Fibers

A simple technique of pulse compression, based on the linear chirp compensation of self-phase modulation (SPM) spectra in dispersion shifted fibers, is demonstrated. The optimization procedure is carried out, for a short span of a single-mode fiber, using a parabolic law, which describes the behavior of the squared output pulse width versus the pump peak power in the case of Gaussian pulses. The experimental results give a minimum pulse duration of 233 fs, which is in good agreement with the model. Shorter and coherent pulses, down to 90 fs, have been obtained by inserting an interference filter at the optical output.     

Effect ofγ-radiation on the spectral luminescence characteristics of impure cadmium tungstate crystals

Results of a study of the effect of γ-radiation on the spectral luminescence properties of cadmium tungstate crystals doped with silver, bismuth, and molybdenum cations are presented. Spectral characteristics of the nondnnnoped crystals are briefly described. Absorption and photo and X-ray luminescence spectra of the crystals taken before and after exposure to γ-radiation (5.5·10⁴ Gy) are compared. It is found that the spectral characteristics of the crystals doped with silver, bismuth, and molybdenum cations do not change markedly after the exposure. The relation between the type of impurity-induced defects, individual characteristics of the impurity cations, and the character of the effect of γ-radiation on the spectral luminescence properties of impure crystals is analyzed (preliminarily). Translated from Zhurnal Prikladnoi Spektroskopii, Vol. 64, No. 1, pp. 55–60, January–February, 1997.     

Sorting of bending magnets for the SSRF booster

The Shanghai Synchrotron Radiation Facility(SSRF)booster ring,a full energy injector for the storage ring,is deigned to accelerate the electron beam energy from 150MeV to 3.5GeV that demands high extraction efficiency at the extraction energy with low beam loss rate when electrons are ramping.Closed orbit distortion(COD)caused by bending magnet field uniformity errors which affects the machine performance harmfully could be effectively reduced by bending magnet location sorting.Considering the affections of random errors in measurement,both ideal sorting and realistic sorting are studied based on measured bending magnet field uniformity errors and one reasonable combination of bending magnets which can reduce the horizontal COD by a factor of 5is given as the final installation sequence of the booster bending magnets in this paper.     

Measurement of nonlinear coefficient of optical fiber based on small chirped soliton transmission

We measure the waveform and phase curves of short optical pulses before and after transmission over different lengths of fibers by use of the pulse analyzer with the frequency-resolved optical gating (FROG),and numerically simulate pulse evolution under the experimental conditions.The nonlinear coefficient of the fiber is given by comparing the experimental results with the numerical ones.Difference between the experiment and numerical simulation is analyzed.     

Resonance scattering of canonical elastic shells in absorbing fluid medium

Resonance scattering of elastic spherical shell and cylindrical shell while the surrounding fluid medium has absorption is studied. The normal mode solution derived using exact elastic theory and the separation of variables is still applicable. However, the scattering form function has to be modified for the absorbing medium, otherwise the unreasonable result would be obtained. The backscattering form function in the absorbing medium is redefined, and the form function of elastic spherical and cylindrical shell with vacuum or solid matter filled is calculated in various absorption conditions. The results show that the absorption of surrounding fluid leads to notable attenuation of the coincidence resonances in the mid-frequency, but it has a little influence on the low-frequency resonance scattering induced by the filler inside the shell.     

Single-beam self-referenced phase-sensitive surface plasmon resonance sensor with high detection resolution

A versatile and low-cost single-beam self-referenced phase-sensitive surface plasmon resonance(SPR)sensing system with ultra-high resolution performance is presented.The system exhibits a root-mean-square phase fluctuation of ±0.0028.over a period of 45 min.i.e.a resolution of±5.2×10-9 refractive index units.The enhanced performance has been achieved through the incorporation of three design elements:a true single-beam configuration enabling complete self-referencing so that only the phase change associated with SPR gets detected,a differential measurement scheme to eliminate spurious signals not related to the sensor response,and the elimination of retardation drifts by incorporating temperature stabilization in the liquid crystal phase modulato .Our design should bring the detection sensitivity of non-labeling SPR biosensing closer to that achievable by conventional fluorescence-based techniques.     

Influences of SiO2 protective layers and annealing on the laser-induced damage threshold of Ta2O5 films

Ta2O5 films are prepared on BK7 substrates with conventional electron beam evaporation deposition.The effects of SiO2 protective layers and annealing on the laser-induced damage threshold (LIDT) of the films are investigated.The results show that SiO2 protective layers exert little influence on the electric field intensity(EFI)distribution,microstructure and microdefect density but increase the absorption slightly.Annealing iS effective on decreasing the microdefect density and the absorption of the films.Both SiO2 protective layers and annealing are beneficial to the damage resistance of the films and the latter is more effective to improve the LIDT.Moreover,the maximal LIDT of Ta2O5 films is achieved by the combination of SiO2 protective layers and annealing.     

A stereo matching algorithm using multi-peak candidate matches and geometric constraints

Gray cross correlation matching technique is adopted to extract candidate matches with gray cross correla- tion coefficients less than some certain range of maximal correlation coefficient called multi-peak candidate matches. Multi-peak candidates are extracted corresponding to three closest feature points at first. The corresponding multi-peak candidate matches are used to construct the model polygon. Correspondence is determined based on the local geometric relations between the three feature points and the multi-peak candidates. The disparity test and the global consistency checkout are applied to eliminate the remaining ambiguous matches that are not removed by the local geometric relational test. Experimental results show that the proposed algorithm is feasible and accurate.