环形障碍物-轴棱锥产生局域空心光束

提出一种产生局域空心光束(bottle beam)的新方法,它是在传统的轴棱锥底面上放置一个环形障碍物.平面波入射到带有环形障碍物的轴棱锥底面时,将在轴棱锥产生的最大无衍射距离内形成bottle beam,而在bottle beam的前后仍然保持无衍射贝塞尔光.通过变化障碍物大小及轴棱锥底角实现bottle beam尺寸的控制.利用衍射理论描述了平面波经带有环形障碍物的轴棱锥产生bottle beam的原理,分析和模拟了传输过程中不同位置的截面光强分布及整个过程的三维光强分布,并给出相关的实验结果.研究结果对bottlebeam的实际应用具有积极的意义.     

产生多个高光强梯度局域空心光束的理论与实验

在实验中用贝塞尔光束与球面波叠加得到多个具有高强度梯度的局域空心光束(BB)。用衍射理论分析了贝塞尔光束与球面波叠加的光场,借助软件对两光场相干叠加的光强分布进行了模拟,结果表明在球面波的焦点附近能够形成多个高强度梯度的BB。实验中贝塞尔光束和球面波分别用轴棱锥和透镜对平行光聚焦获得,使两光场在同一传播轴上相干叠加,在球面波焦点附近观察到多个BB。通过对比可知,贝塞尔光束与球面波叠加所得BB比用两束贝塞尔光束干涉产生的BB在暗域处具有更大的光强梯度,更有利于稳定的粒子囚禁。     

阶变折射率轴棱锥产生局域空心光束

提出利用折射率成阶跃性变化的轴棱锥产生局域空心光束(bottlebeam).讨论了折射率沿径向成阶跃式减小或增加两种模型,从几何光学角度分析了它们产生bottle beam的原理,利用衍射积分理论数值模拟两种轴棱锥光传输的光场分布和不同距离处的二维光斑图,研究结果表明折射率沿径向阶跃减小的轴棱锥产生单个bottle beam,而折射率沿径向阶跃增加的轴棱锥产生具有周期再现的bottle beams.bottle beam在原子引导和囚禁、光学俘获及光镊等方面有广泛的应用,因此本文的研究对bottlebeam的产生和实际应用具有指导意义.     

圆顶轴棱锥底角及焦距对局域空心光束的影响

从衍射理论导出圆顶轴棱锥后的光场分布,用软件对圆顶轴棱锥后的光强进行仿真,结果表明,圆顶轴棱锥可以得到多个局域空心光束。分别改变圆顶轴棱锥的底角和顶端平凸透镜的焦距,再用软件对圆顶轴棱锥后的光强进行仿真,所得光强分布表明,圆顶轴棱锥的底角影响局域空心光束的周期和暗域数量,而顶端平凸透镜的焦距主要影响局域空心光束中暗域的数量,对周期几乎没有影响。在实际应用中可通过调节参量得到所需要局域空心光束。     

梯度轴棱锥产生单个Bottle beam

首次提出一种新的梯度轴棱锥模型,这种梯度轴棱锥在传统的轴棱锥基础上,将轴棱锥顶点的锥角设计成具有一定的梯度.平面波入射到这种梯度轴棱锥,其衍射场会形成两个区域的Bessel光,并且在这两个Bessel光之间形成一个Bottle beam（局域空心光束）.由于Bottle beam具有三维封闭的空心区域和极高的强度梯度,可用作激光导管、光镊和光学扳手等,在生命科学和纳米科技中有重要应用.从几何光学角度分析了梯度轴棱锥形成单个Bottle beam的原理,由衍射及相干理论,分析和模拟了纵向剖面光强分布和横截面光强分布.研究结果对梯度轴棱锥的设计和应用具有指导意义. 关键词： 梯度轴棱锥 Bottle beam 轴棱锥 Bessel光     

新型锥透镜产生局域空心光束

首次提出产生局域空心光束(Bottle beam)的另一类新型锥透镜模型.讨论了凹凸两种模型,分别是在传统轴棱锥的底部磨削和胶合圆台结构形成.研究结果表明平面波正入射新型凹锥透镜可产生单个Bottle beam,正入射新型凸锥透镜可形成具有周期性的Bottle beam.通过几何光学分析了产生Bottle beam的原理,计算了Bottle beam的相关参数.由衍射积分理论分析和模拟了新型锥透镜后的光强分布特性,所得分析结果与几何光学分析基本符合. 关键词： 新型锥透镜 Bottle beam 轴棱锥 Bessel光     

无衍射Mathieu光束经轴棱锥的聚焦特性

基于Mathieu-Hankel波理论分析了Mathieu光束经轴棱锥后的聚焦特性,并利用菲涅尔衍射积分理论及稳相法,推导出Mathieu光束经轴棱锥后的准确解析表达式.数值模拟了无衍射Mathieu光束经轴棱锥线性聚焦后的光场在不同传播距离处的截面光强分布及轴上光强分布.理论分析及数值模拟均表明无衍射Mathieu光束经轴棱锥聚焦后会产生周期性Mathieu光束.研究结果对扩展Mathieu光束的应用范围提供了理论依据.     

干涉理论对bottle beam的描述

对轴棱锥产生的贝塞尔光聚焦特性的描述，我们提出一种有别于惠更斯-菲涅耳衍射积分理论的解析表达.这种解析表达基于干涉理论的基础，它能够模拟计算出聚焦透镜置于最大准直距离之外以及在聚焦透镜焦平面以后的光束行为，能够更好地描述bottle beam的形成过程，这些结果用衍射积分理论是得不到的.我们还得到了与Wei用几何光学分析所得出的当z_0max将产生hollow beam的不同结论.所有理论计算结果都得到实验的有力验证. 关键词： bottle beam 贝塞尔光 轴棱锥 光镊     

无衍射贝塞尔光束相干的理论与实验

 分别使用两种不同底角的轴棱锥产生无衍射贝塞尔光束。理论分析了单束贝塞尔光及两束贝塞尔光相干叠加后光场的光强分布,分析了产生的局域空心光束在一个完整周期内的特性。数值模拟了光沿纵向传播时光场的横向光强分布,并给出了相关的实验。对单束贝塞尔光及两束贝塞尔光干涉后的中心光斑的大小进行了测量,测量结果与理论计算结果吻合。     

双焦透镜对Bessel光束传输的影响

研究非轴对称象散光学元件双焦透镜对无衍射Bemel光束的聚焦特性.基于空间域中的广义惠更斯.菲涅耳衍射理论衍射积分,用4×4阶矩阵来描述非轴对称光学系统,导出Bessel光通过双焦透镜更为普遍和广义的光强分布表达式,并对其光强进行数值模拟.分析双焦透镜在x,y面上的焦距取不同值时对Bessel光的影响.导出的广义光强分布表达式包括了普通透镜、双焦透镜和柱透镜的所有情况.研究发现,当象散越大,图形畸变程度越大,导致得到的光学bottle beam的光束质量下降,bottle壁变形,囚禁微观粒子的能力也随之下降.     

Guided-Wave Two-Dimensional Acousto-Optic Scanner Using Proton-Exchanged Lithium Niobate Waveguide

Two-dimensional scanning of a 0.6328 mum guided-light beam has been realized using noncolinear acousto-optic (AO) coplanar Bragg diffraction together with colinear AO guided-mode to substrate radiation-mode conversion in a Z-cut Xpropagation LiNbO3 proton-exchanged (PE) waveguide. The two surface acoustic (SAW) waves utilized are at the center frequencies of 500 and 200 MHz, propagating in the Y and X axes, respectively. Two-dimensional scanning of approximately 720 resolvable light beam spots, namely, 18 40 (horizontal vertical) scanning, has been demonstrated using a light beam of 1.0 mm aperture. The total number of resolvable beam spots can be greatly increased from 720 by simply utilizing SAW transducers of larger bandwidth and a light beam of greater aperture. It should also be possible to significantly increase the diffraction efficiency from 3 % by optimizing the parameters of the PE waveguide and the SAWs.     

Effect ofγ-radiation on the spectral luminescence characteristics of impure cadmium tungstate crystals

Results of a study of the effect of γ-radiation on the spectral luminescence properties of cadmium tungstate crystals doped with silver, bismuth, and molybdenum cations are presented. Spectral characteristics of the nondnnnoped crystals are briefly described. Absorption and photo and X-ray luminescence spectra of the crystals taken before and after exposure to γ-radiation (5.5·10⁴ Gy) are compared. It is found that the spectral characteristics of the crystals doped with silver, bismuth, and molybdenum cations do not change markedly after the exposure. The relation between the type of impurity-induced defects, individual characteristics of the impurity cations, and the character of the effect of γ-radiation on the spectral luminescence properties of impure crystals is analyzed (preliminarily). Translated from Zhurnal Prikladnoi Spektroskopii, Vol. 64, No. 1, pp. 55–60, January–February, 1997.     

Femtosecond Transform-Limited Pulse Generation by Compensating for the Linear Chirp of SPM Spectra in Dispersion Shifted Fibers

A simple technique of pulse compression, based on the linear chirp compensation of self-phase modulation (SPM) spectra in dispersion shifted fibers, is demonstrated. The optimization procedure is carried out, for a short span of a single-mode fiber, using a parabolic law, which describes the behavior of the squared output pulse width versus the pump peak power in the case of Gaussian pulses. The experimental results give a minimum pulse duration of 233 fs, which is in good agreement with the model. Shorter and coherent pulses, down to 90 fs, have been obtained by inserting an interference filter at the optical output.     

Sorting of bending magnets for the SSRF booster

The Shanghai Synchrotron Radiation Facility(SSRF)booster ring,a full energy injector for the storage ring,is deigned to accelerate the electron beam energy from 150MeV to 3.5GeV that demands high extraction efficiency at the extraction energy with low beam loss rate when electrons are ramping.Closed orbit distortion(COD)caused by bending magnet field uniformity errors which affects the machine performance harmfully could be effectively reduced by bending magnet location sorting.Considering the affections of random errors in measurement,both ideal sorting and realistic sorting are studied based on measured bending magnet field uniformity errors and one reasonable combination of bending magnets which can reduce the horizontal COD by a factor of 5is given as the final installation sequence of the booster bending magnets in this paper.     

Measurement of nonlinear coefficient of optical fiber based on small chirped soliton transmission

We measure the waveform and phase curves of short optical pulses before and after transmission over different lengths of fibers by use of the pulse analyzer with the frequency-resolved optical gating (FROG),and numerically simulate pulse evolution under the experimental conditions.The nonlinear coefficient of the fiber is given by comparing the experimental results with the numerical ones.Difference between the experiment and numerical simulation is analyzed.     

Resonance scattering of canonical elastic shells in absorbing fluid medium

Resonance scattering of elastic spherical shell and cylindrical shell while the surrounding fluid medium has absorption is studied. The normal mode solution derived using exact elastic theory and the separation of variables is still applicable. However, the scattering form function has to be modified for the absorbing medium, otherwise the unreasonable result would be obtained. The backscattering form function in the absorbing medium is redefined, and the form function of elastic spherical and cylindrical shell with vacuum or solid matter filled is calculated in various absorption conditions. The results show that the absorption of surrounding fluid leads to notable attenuation of the coincidence resonances in the mid-frequency, but it has a little influence on the low-frequency resonance scattering induced by the filler inside the shell.     

Single-beam self-referenced phase-sensitive surface plasmon resonance sensor with high detection resolution

A versatile and low-cost single-beam self-referenced phase-sensitive surface plasmon resonance(SPR)sensing system with ultra-high resolution performance is presented.The system exhibits a root-mean-square phase fluctuation of ±0.0028.over a period of 45 min.i.e.a resolution of±5.2×10-9 refractive index units.The enhanced performance has been achieved through the incorporation of three design elements:a true single-beam configuration enabling complete self-referencing so that only the phase change associated with SPR gets detected,a differential measurement scheme to eliminate spurious signals not related to the sensor response,and the elimination of retardation drifts by incorporating temperature stabilization in the liquid crystal phase modulato .Our design should bring the detection sensitivity of non-labeling SPR biosensing closer to that achievable by conventional fluorescence-based techniques.     

Influences of SiO2 protective layers and annealing on the laser-induced damage threshold of Ta2O5 films

Ta2O5 films are prepared on BK7 substrates with conventional electron beam evaporation deposition.The effects of SiO2 protective layers and annealing on the laser-induced damage threshold (LIDT) of the films are investigated.The results show that SiO2 protective layers exert little influence on the electric field intensity(EFI)distribution,microstructure and microdefect density but increase the absorption slightly.Annealing iS effective on decreasing the microdefect density and the absorption of the films.Both SiO2 protective layers and annealing are beneficial to the damage resistance of the films and the latter is more effective to improve the LIDT.Moreover,the maximal LIDT of Ta2O5 films is achieved by the combination of SiO2 protective layers and annealing.     

A stereo matching algorithm using multi-peak candidate matches and geometric constraints

Gray cross correlation matching technique is adopted to extract candidate matches with gray cross correla- tion coefficients less than some certain range of maximal correlation coefficient called multi-peak candidate matches. Multi-peak candidates are extracted corresponding to three closest feature points at first. The corresponding multi-peak candidate matches are used to construct the model polygon. Correspondence is determined based on the local geometric relations between the three feature points and the multi-peak candidates. The disparity test and the global consistency checkout are applied to eliminate the remaining ambiguous matches that are not removed by the local geometric relational test. Experimental results show that the proposed algorithm is feasible and accurate.