硫堇衍生化自组装膜修饰金电极的电化学性质及其对抗坏血…

将硫堇共价键合到自组装在金电极表面的半胱胺单分子层上，制成了衍生化自组装单分子膜修饰电极，并用电化学方法研究了它的电化学性质，循环伏安图显示其在ｐＨ＝７．７的磷酸盐缓冲液中，于－０．４５～＋０．５０Ｖ（ｖｓ．ＳＣＥ）范围内有２对氧化还原峰，峰电位分别为Ｅｐａ＝２１４ｍＶ，Ｅｐｃ＝８２ｍＶ，Ｅ＾２ｐａ＝－７５ｍＶ，Ｅ＾２ｐｃ－－１６０ｍＶ（ｖｓ．ＳＣＥ），ｐＨ在５．０～９．０范围内，峰１有２个质子参     

生物分子电催化的研究：V.邻菲绕啉电化学聚合修饰电极的性质

本文用恒电位，恒电流，循环扫描等电化学方法，首次制备了邻菲绕啉（０－ｐｈｅｎ）聚合膜修饰电极，在０．０１ｍｏｌ／ＬＫＣｌＯ４水溶液中，其氧化与还原过程的峰电位分别为＋０．０４Ｖ和－０．５３Ｖ（ｖｓ．ＳＣＥ），该修饰电极在酸性，中性，碱性条件下均具有良好的稳定性，能较好地改善Ｋ３Ｆｅ（ＣＮ）６和Ｖｋ３在电极上的氧化还原性质，对维生素Ｃ和肼的氧化有很好的催化作用，其氧化峰电位分别降低２２０ｍＶ和５６２     

酞菁锰-表面活性剂薄膜电极的电化学表征及其对三氯乙酸的电化学催化作用的研究

将酞菁锰（ＭｎＰｃ）掺入阳离子表面活性剂双十二烷基二甲基溴化铵（ＤＤＡＢ）的氯仿溶液，并涂布于热解石墨电极表面，待氯仿挥发后即制得ＭｎＰｃ－ＤＤＡＢ薄膜电极。循环伏安实验表明，在ＫＢｒ溶液中，该薄膜电极有两对还原氧化峰，第一对峰的Ｅｐｃ１＝－０．２７Ｖ，Ｅｐａ１＝０．０１Ｖ；第二对峰的Ｅｐｃ２＝－０．７６Ｖ，Ｅｐａ２＝－０．６２Ｖ（ｖｓ．ＳＣＥ）。本文着重探讨了第二对峰的电化学行为，估计了该体系的电荷传递扩散系数Ｄｃｔ和表观非均相电极反应速率常数Ｋ０′等电化学参数，并可将该薄膜电极用于催化三氯乙酸的电化学还原。     

NADH在邻苯二酚紫修饰石墨电极上的电催化氧化

以吸附在石墨电极上的邻苯二酚紫作为电子传递媒介体构成修饰电极。在－０．４０－＋０．６０Ｖ电位区间内，吸附态的邻苯二酚紫表现出相当可逆的氧化，还原行为，电极反应为单电子过程并有１个质子参加。在ｐＨ为７．０的磷酸盐缓冲溶液中，其式量电位Ｅ＾ｏ＇为０．１０Ｖ，表观电极反应速率常数ｋｓ为５．５ｓ＾－＾１。邻苯二酚紫修饰电极对还原型烟酰胺腺嘌呤二核苷酸（ＮＡＤＨ）的电化学氧化具有明显的催化作用。可使ＮＡＤＨ     

酞菁镍—表面活性剂薄膜修饰电极及其催化性能的研究

将酞菁镍（ＮｉＰｃ）掺入阳离子表面活性剂双十二烷基二甲基溴化铵（ＤＤＡＢ）的氯仿溶液中，并涂布于热解石墨电极表面，待氯仿挥发后制得ＮｉＰｃ－ＤＤＡＢ薄膜电极。循环伏安实验表明，在ＫＢｒ溶液中，该薄膜电极有两对良好且稳定的还原氧化峰，第一对峰的Ｅｐｃ１＝－０．６４Ｖ，Ｅｐａｌ＝－０．６０Ｖ（ｖｓ．ＳＣＥ）；第二对峰的Ｅｐｃ２＝－０．８４Ｖ，Ｅｐａ２＝－０．８０Ｖ。本文着重探讨了第二对峰的电化学行为，     

酞菁锰—表面活性剂薄膜电极的电化学表征及其对三氯乙酸的电化学催 …

将酞菁锰（ＭｎＰｃ）掺入阳离子表面活性剂双十二烷基二甲基溴化铵（ＤＤＡＢ）的氯仿溶液，并涂布于热解石墨电极表面，待氯仿挥发后即制得ＭｎＰｃ－ＤＤＡＢ薄膜电极，循环伏安实验表明，在ＫＢｒ溶液中，该薄膜电极有两对还原氧化峰，第一对峰的Ｅｐｃｔ＝－０．２７Ｖ，Ｅｐａ１＝０．０１Ｖ；第二对峰的Ｅｐｃ２＝－０．７６Ｖ，Ｅｐａ２＝－０．６２Ｖ（ｖｓ．ＳＣＥ）。本文着重探讨了第二对峰的电化学行为，估计了该体系电     

金在脱乙酰壳多糖学修饰电极上的电化学行为及分析应用

用脱乙酰壳多糖化学修饰电极为工作电极，阳极溶出伏安法测定痕量金。在ｐＨ１￣２的ＫＣｌ－ＨＣｌ底液中，超始电位０．２０Ｖ，终止电位１．３０Ｖ，富集时间５ｍｉｎ，以－０．１／ｓ扫速阳极溶出，峰电位在１．００Ｖ（ｖｓ．ＳＣＥ），Ａｕ（Ⅲ）浓度在０．１０ｍｇ／Ｌ￣１０ｍｇ／Ｌ范围内与峰高呈线性关系。在富集１０ｍｉｎ时，可检测０．２５ｍｉｇ／ＬＡｕ，大大提高了测定灵敏度，用于矿样测定，无需分离，结果满意。用     

硼掺杂多晶金刚石薄膜电极的电化学特性

用循环伏安法和恒电位法研究了硼掺杂多晶金刚石薄膜电极（ＤＦＥ）的若干电化学特性。电极面积４×４ｍｍ＾２。在０．１ｍｏｌ／Ｌ ＫＣｌ，ＮａＮＯ３，ＮａＯＨ和ＫＨ２ＰＯ４＋Ｎａ２ＨＰＯ４（ｐＨ＝６．８６）电解质溶液中电势窗口均为－５００￣＋８００ｍＶ；而在０．１ｍｏｌ／Ｌ ＨＣｌ和Ｈ２ＳＯ４溶液中电势窗口为－２００￣＋１１００ｍＶ．Ｋ３Ｆｅ（ＣＮ）６的氧化峰电位为＋５００ｍＶ，与Ｐｔ电极测量相同；校正     

脱乙酰壳多糖化学修饰电极测定铂的研究

用脱乙酰壳多糖修饰电极为工作电极，阳极溶出伏安法测定痕量铂。在ｐＨ＝２￣３的ＫＣｌ－ＨＣｌ底液中，－０．３Ｖ富集２ｍｉｎ，静止１５ｓ，以０．２Ｖ／ｓ扫速阳极溶出，峰电位在－０．１６Ｖ（ｖｓ．ＳＣＥ），铂（Ⅳ）离子浓度在０．５￣５．０μｇ／ｍＬ范围内与峰高呈线性关系。富集１０ｍｉｎ后，可检测０．０２５μｇ／ｍＬ铂（Ⅳ）。该法用于贵金属矿样的测定，无需分离，结果满意。用循环伏安法、紫外光谱和拉曼光谱研     

磷钼杂多酸-L-半胱氨酸自组装超分子膜电极对亚硝酸根电催化还原的研究

制备了磷钼杂多酸－Ｌ－半胱氨酸自组装超分子膜电极（Ｐ２Ｍｏ１８－Ｌ－Ｃｙｓ／Ａｕ）。采用水平衰减全反射（ＡＴＲ－ＦＴＩＲ）光谱表征了膜的组成。研究了该膜电极的电化学性质，发现它在１．０ ｍｏｌ／Ｌ　Ｈ２ＳＯ４溶液中，于０．０～０．７Ｖ（ｖｓ．ＳＣＥ）间ＣＶ扫描出现两对稳定、可逆的氧化还原峰，其中峰电位分别为Ｅｍ１＝０．３３４ Ｖ，Ｅｍ２＝０．１８８Ｖ，对应着Ｐ２Ｍｏ１８Ｏ_(６２)~(６－)的两步２电子－２质子反应；计时库仑法计算了薄膜内的电子传递系数Ｄ为５．０１ × １０~（－８）ｃｍ２·ｓ～（－１）。该膜电极对酸性溶液中的ＮＯ_２~－有明显的电催化还原作用，初步探讨了电催化机理。用差分脉冲伏安法（ＤＰＶ）测定其还原峰电流与ＮＯ_２~－的浓度在２．０ ×１０~（－６）～２．０ × １０~（－４）ｍｏｌ／Ｌ范围内呈良好的线性关系，相关系数为０．９９５３，检测限５．０×１０~（－７）ｍｏｌ／Ｌ。该电极用于模拟水样中ＮＯ_２~－的测定，结果满意。     

Side effects in measurements of selectivity coefficients of solid state ion selective electrodes

The influence of various factors such as solubility, the oxidation of the membrane, and the contamination of the solution, on the experimental values of the selectivity coefficients of solid state sulphide ion selective electrodes is discussed. A new method for the evaluation of very small selectivity coefficients, based on the addition of reagents forming complexes or insoluble salts with the main ion, is proposed. By means of this method, selectivity coefficients for silver, copper, cadmium and lead ion selective electrodes have been determined, which are in far better agreement with thermodynamic values than those described in the literature.     

用氧化还原聚合物修饰多孔电极

对３种类型Ｎａｆｉｏｎ／Ｏｓ（ｂｐｙ）３Ｃｌ２修饰电极的研究结果表明，单位表观电极面积上中继体载量比为：乙炔黑粉末微电极（Ａ）：Ｔｅｆｌｏｎ粘结的乙炔黑膜电极（Ｂ）：平面玻碳电极（Ｃ）＝１０＾３：１０＾２：１．Ａ比Ｂ及Ｃ更容易在真实表面上形成花天酒地而均匀的修饰层而有利于层内的电荷传递。在Ａ类电极基础上制行的葡萄糖酶电极在１０ｍｍｏｌ／Ｌ葡萄糖溶液中的响应电流密度高达４．６×１０＾－＾４Ａ／ｃｍ＾     

新型硫醇硫组合电极研制及性能测试

把玻璃参比电极、环状的银-硫化银指示电极、以及铂丝屏蔽电极组合形成新型硫醇硫组合电极,研究了在含有0.2 mol/L硫离子的醇-水-氨介质中,在表面活性剂存在下,以环状银电极为阳极,恒定微电流电沉积的方式制备硫化银敏感层的条件。由此法制得的新型硫醇硫组合电极在Ag 浓度为1.0×10-1~1.0×10-5mol/L范围内斜率为59.0±0.5 mV/pC,测量下限为2.2×10-6mol/L,与同类商品电极相比,响应速度快、记忆效应小、重复性好、电位稳定,易于批量生产,具有较强的适应性和应用价值。     

内场致发射电极的电化学行为

在N-Si和P-Si半导体上用化学沉积法制备了内场致发射电极并研究了它们的电化学行为。从分解电势Ⅰ～Ⅴ曲线可知,这种电极可在低于1.23V下分解水;对Fe~(3+)/Fe~(2+)体系的循环伏安图,其峰电流为铂电极的8倍多。     

Electroanalytical Determination of Vancomycin at a Graphene‐modified Electrode: Comparison of Electrochemical Property between Graphene,Carbon Nanotube,and Carbon Black

Carbon nanotube, graphene and carbon black, as electrode modifiers, were compared and evaluated for the electrochemical determination of vancomycin. Among them, the best results were obtained at the graphene‐modified electrode. Additions of vancomycin using square wave voltammetry at the graphene‐modified electrode showed a linear range from 0.70 μM to 50 μM and a detection limit of 0.20 μM was obtained. To control the correct dose of vancomycin and reduce its side effects, its accurate determination in blood plasma is very important. Therefore, the method was applied for the vancomycin determination in spiked human plasma samples and satisfactory recoveries were observed. The developed method exhibited fast analysis, high sensitivity, good repeatability and freedom from other interfering species.     

Carbon-Filled Polymer Paste Reference Electrodes

Abstract

Inexpensive, disposable, carbon-filled polymer paste reference electrodes are reported. These electrodes are designed for use in conjuction with carbon-filled polymer paste ion-selective probes reported earlier. Attachment of integrated electronics is easily achieved.     

Poly(vinyl chloride) membrane electrode for the determination of verapamil

A verapamil-PVC membrane ion-selective electrode based on the verapamil-reineckate ion pair was prepared with dibutyl phthalate as a plasticizer. The electrode exhibited a linear response with a Nernstian slope (52.8 mV decade^?1 at 20° C) for verapamil concentrations of 10^?5?10^?2M over the pH range 3–7. The electrode also exhibited very good selectivity for verapamil with respect to various inorganic and organic cations. Gran II linear titration and potentiometric titration were used to determine verapamil in pure solution, with an average recovery of 99.3% and a relative standard deviation of 0.4%.     

Development of new potentiometric sensors for the determination of proguanil hydrochloride in serum and urine

Potentiometric electrodes were developed for the rapid determination of proguanil hydrochloride in pure samples, pharmaceutical preparations and spiked serum and urine samples using PVC membrane,screen printed(SPE), coated wired(CWE), carbon paste(CPE) and modified carbon paste(MCPE)electrodes based on the ion-exchanger of proguanil with phosphotungestic acid(Pr-PT) as a chemical modifier. The prepared electrodes showed Nernestian slopes of 59.7, 58.1, 58.5, 58.5 and 57.0 for the PVC,SPE, CWE, CPE and MCPE for the proguanil ions in a wide concentration range of 1.0 * 10~(-5)–1.0 * 10~(-2)mol L~(-1) at 25°C with detection limits of 7.94 * 10~(-6), 1.0 * 10~(-5), 1.0 * 10~(-6), 7.07 * 10~(-6) and 2.5 * 10~(-6) mol L~(-1), respectively. The prepared electrodes exhibited high proguanil selectivity in relation to several inorganic ions and sugars and they could be successfully utilized for its determination in pure solutions, pharmaceutical preparations and serum and urine samples using the direct potentiometry and standard addition methods with very good recovery values.     

在298K标准锌汞齐电极的标准电极电势

饱和锌汞齐电极的标准电极电势,一般是指含锌量10％的锌汞齐电极对活度为1的锌离子所产生的电极电势,ε_(Zn~2+)~0+Zn-Hg(Zn10％)=—0.7618±0.0008V。固体金属锌电极的标准电极电势是指金属锌电极对活度为1的锌离子所产生的电极电势ε_(Zn~2+)~0-Zn=0.7618V。