铕的时间分辨激光荧光光谱分析：Ⅰ方法研究

本工作是在自建装置上，利用时间分辨激光荧光光谱技术，选择Ｅｕ－ＴＴＡ－ＥｔＯＨ液体荧光体系，建立了时间分辨激光荧光测定铕的方法。该测定铕离子的线性范围为０．０００２－１０μｇ／ｍｌ检测限为１０＾－５μｇ／ｍｌ。０．０３μｇ／ｍｌＥｕ＾３＋标准样品ＥｕＴＴＡ３，测定的相对标准偏差为４．７％，该法用于实际样品的分析测定，结果满意。结合铕的分析，对本方法选择化学体系的条件、测定装置的参数进行了讨论。并获     

ICP—AES法直接测定高纯Eu2O3中14种稀土元素

建立了ＩＰＣ－ＡＥＳ测定高纯Ｅｕ２Ｏ３中１４种稀土元素的方法，用正交设计法优化仪器测量条件，实验了基体Ｅｕ２Ｏ３对被测元素的干扰和对方法测定下限的影响。１４个稀土元素的测定下限为：Ｙｂ２Ｏ３０．５μｇ．ｇ＾－１，Ｙ２Ｏ３１μｇ．ｇ＾－１，Ｄｙ２Ｏ３，Ｈｏ２Ｏ３，Ｔｍ２Ｏ３和Ｎｄ２Ｏ３５μｇ．ｇ＾－１、Ｇｄ２Ｏ３、Ｓｍ２Ｏ３、Ｅｒ２Ｏ３、Ｃｅ２Ｏ３、Ｐｒ６Ｏ１１和Ｌａ２Ｏ３１０μｇ．ｇ＾－１，Ｌｕ２     

新间接紫外光度法测定微量SO3^2—

在ｐＨ７．０混合磷酸盐介质中,ＳＯ３＾２－使Ｉ３＾－与ＣＴＭＡＢ生成离子缔合物ＣＴＭＡ＾＋,Ｉ３＾－而褪色,从而建立了测定ＳＯ３＾２－的新间接紫外光度法,测定波长为３６５ｎｍ,ＳＯ３＾２－浓度在０－２５μｇ／２５ｍＬ内服从比耳定律,表观摩耳吸光系数为ε＝６．０４×１０＾４Ｌ·ｍｏｌ＾－１·ｃｍ＾－１,可用于食品中微量ＳＯ３＾２－的测定,其结果满意。     

分光光度法测定香菇中硒的研究

在ＨＣｌ介质中３,３’－二氨基联 胺与硒反应生成黄色络合物,λｍａｘ＝４２０ｎｍ,ε＝４＊１０＾４Ｌ．ｍｏｌ＾－１．ｃｍ＾－１,硒含量在０．５－５０μｇ／２５ｍＬ范围内符合比耳定律,本方法用于香菇样品中硒的测定,结果令人满意。     

La2O3—BaO系复氧化物的现场拉曼光谱研究

对于Ｌａ０．２Ｂａ０．８－ｘＣａｘ（Ｏ，ＣＯ３）其中ｘ＝０．０、０．２、０．４、０．６氧化物在９７３Ｋ及甲烷氧化偶联（ＯＣＭ）条件下，无Ｃａ＾２＋的样品可用表面ＢａＣＯ３和（ＬａＯ）２ＣＯ３的Ｒａｍａｎ谱及８１０ｃｍ＾－１附近的Ｏ２＾２－特征峰来表征；含Ｃａ＾２＋的样品，则表现了混合碳酸盐（Ｃａ，Ｂａ）ＣＯ３的特征，还有位于１１３５ｃｍ＾－１（ｗ）和８１０ｃｍ＾－１（ｗ）的Ｏ２＾－、Ｏ２＾２－瞬时     

析相光度法测定铜（Ⅱ）的研究

本文研究了Ｃｕ－ＰＥＧ－ＤＤＴＣ（铜试剂）（ＮＨ４）２ＳＯ４体系的析相光度法并应用于测定Ｃｕ。最宜酸度为３．６－９．０（ＮａＡｃ－ＨＡｃ，ＮＨ４Ｃｌ－ＮＨ３．Ｈ２Ｏ）缓冲溶液，其络合物的最大吸收位于４５０ｎｍ，表观摩尔吸光系数为９．０５×１０＾３Ｌ．ｍｏｌ＾－１．ｃｍ＾－１，Ｃｕ浓度在０－３０μｇ／Ｌ范围内服从比耳定律，铜与ＤＤＴＣ形成组成为１：２的稳定络合物。该方法用于铝合金中铜的测定，获得了满     

退色光度法测定痕量Cr(Ⅲ)的研究

基于在ＯＰ存在下,痕量Ｃｒ（Ⅲ）可使萘酚绿Ｂ退色的反应,本文提出了一种应用新的退色光度法测定痕量Ｃｒ（Ⅲ）的方法,该方法线性范围为０．２４－３．００μｇ．ｍＬ＾－１,检出限为２．０５μｇ．ｍＬ＾－１。该方法用于模拟样品的测定,回收率为１００％－１０８％。     

乳酸亚铁中总铁的溶样及比色测定

本文研究在ＨＮＯ３－ＨＣｌ体系乳酸亚铁中的Ｆｅ＾２＋会被氧化成Ｆｅ＾３＋，用碘基水杨酸比色法就能准确测定总铁量，回收率在９８％－１００％，相对标准偏差为１．１４％，摩尔吸光系数为５．６×１０＾４Ｌ．ｍｏｌ＾－１．ｃｍ＾－１，含铁量在０－７００μｇ／１００ｍＬ范围内符合比耳定律。     

（La2／3Ca1／3）（Mn（3—x）／3Gax／3）O3体系巨磁电阻效应和电特性的研究

采用固态反应法制备了（Ｌａ２／３Ｃａ１／３）（Ｍｎ（３－ｘ）／３Ｇａｘ／３）Ｏ３（ｘ＝０．００，０．１０，０．１５，０．２０，０．３０）体系的系列样品。通过系统地测量其零场和１．６特斯拉（Ｔ）磁场下样品的电阻率－温度关系以及一定温度下磁电阻率与磁场的关系，发现随Ｇａ＾３＋替代量的增加其磁电阻率峰和电阻率峰均向低温方向移动，磁电阻率峰值增大，并伴生磁电阻率峰展宽效应。作者认为，上述结果是由于Ｇａ＾３     

湿法灰化火焰原子吸收光谱测定胭脂花中微量锌

本文采用ＨＮＯ３－ＨＣｌＯ４湿灰化法火焰原子吸收光谱测定胭脂花种子，胚乳，叶片和枝中的微量锌，实测了４０多个样品，该法与常规的比色法相比，具有较高的灵敏度和准确度，简化了处理手续，缩短了测定时间，也减少了污染和测定元素处理过程中的损失。检出限为０．０１μｇ．ｇ＾－１。相对标准偏差小于５％，回收率在９５％－１０５％之间。     

Speckle characteristics of a broad-area VCSEL in the incoherent emission regime

We present a technique to reduce the speckle contrast of a NIR broad-area VCSEL based on the spatially incoherent emission regime that can be obtained when using the proper driving conditions. We evaluate the efficiency of this technique to reduce the speckle contrast by comparing it with the speckle characteristics in multimode emission under cw operation. Depending on the illumination setup, the incoherent emission regime can lead to a strongly reduced speckle contrast down to 1.3%. This is in agreement with estimates of the expected speckle contrast reduction when three contrast reducing effects are taken into account. These low contrast values make the investigated sources attractive for several applications that suffer from speckle noise.     

XYZ particles at Belle

In this paper, I review recent progress in the study of the XYZ particles at Belle. I only focus on studies with charmonium and one or more light mesons in the final states. This covers the X(3872), X(3915),Y(4140), X(4350), and the charged Z states.     

Beyond the LAN: Ethernet’s Evolution into the Public Network

This article details the evolution of Ethernet into Gigabit Ethernet and how this LAN-based technology has undergone major transformations over time. From its data rates and distances to supported media and functionality, Ethernet has greatly improved, enabling it to surmount many of its former limitations and in so doing to expand beyond the LAN into the MAN and now even the WAN. In this article, Pioneer Consulting explores the evolution further by focusing on some of the major technological directions in the Ethernet equipment industry.     

Optical transmission through an interface between subwavelength slits

This paper studies optical transmission through an interface between two slits with different widths in a sheet composed of an ideal conductor. Such a structure is of potential use in fabricating optical diode and may be the simplest one compared to other designs. Our calculations show that there is a critical wavelength. When the light wavelength is below the critical wavelength, the transmissivity is unidirectional. The expression of the stable transmissivity as a function of the ratio of the widths of the two slits was obtained analytically. Particularly, at the critical wavelength, the transmissivities are zero. This phenomenon has great potential for application in the manufacture of wavelength blockers.     

带有碳杂质的钨中氢稳定性的第一性原理研究

应用第一性原理计算方法研究了碳(C)原子对钨(W)中氢(H)原子稳定性的影响. 本征W中, 当C-H间距离为～2.5 Å时, H的溶解能出现最低值, 此时为H最稳定的位置. W中存在空位时, 由于C的影响, H占据的最佳电子密度面值为0.10 Å^-3. 研究发现, W中单空位最多能容纳10个H原子, 且不能形成H分子, 不同于没有C存在的情况, 表明C对W中H稳定性存在很大影响. 此外, 当两个C原子存在于空位中时, H占据的最佳电子密度面值变为0.13 Å^-3.     

Effect of swift heavy ion irradiation on photoluminescence properties of ZnO/PMMA nanocomposite films

We report a study on the SHI induced modifications on structural and optical properties of ZnO/PMMA nanocomposite films. The ZnO nanoparticles were synthesized by the chemical route using 2-mercaptoethanol as a capping agent. The structure of ZnO nanoparticles was confirmed by XRD, SEM and TEM. These ZnO nanoparticles were dispersed in the PMMA matrix to form ZnO/PMMA nanocomposite films by the solution cast method. These ZnO/PMMA nanocomposite films were then irradiated by swift heavy ion irradiation (Ni⁸⁺ ion beam, 100 MeV) at a fluence of 1×10¹¹ ions/cm². The nanocomposite films were then characterized by XRD, UV-vis absorption spectroscopy and photoluminescence spectroscopy. As revealed from the absorption spectra, absorption edge is not changed by the irradiation but the optical absorption is increased. Enhanced green luminescence at about 527 nm and a less intense blue emission peak around 460 nm were observed after irradiation with respect to the pristine ZnO/PMMA nanocomposite film.     

Grain boundary potential and charge density at grain boundaries of chemically prepared thin silver sulfide films

The grain boundary potential and interface state charge density at the grain boundaries of silver sulfide (Ag₂S) thin films prepared by chemical conversion of cadmium sulfide (CdS) films have been determined from the dc resistance of the material and are found to be sensitive to annealing. A reduction in the grain boundary potential and the grain boundary charge density of the film has been noticed when the source CdS film is annealed at different temperatures prior to chemical conversion. The variation in the grain boundary charge density of the grown Ag₂S film with source annealing temperature has been found to be similar to that of thin cadmium sulfide film, reported earlier. An additional low temperature heat treatment of the sample results in an enhancement in the charge density at the grain boundaries. The change in the silver vacancy and/or oxygen and sulfur content of the films as revealed from the energy dispersive spectra of the films suggests possible role of film composition on the grain boundary charge density.     

Reflections from polished single mode fiber ends

Abstract

The performance of a wavelength division multiplexing (WDM) system with optical cross-connects (OXCs) and in the presence of polarization and nonlinear effects was analyzed. We determined the effect of PMD and PDL; nonlinearity such as XPM, SPM, and FWM; and CD on the system performance. We found that the system outage probability is highest at DGD threshold for the respective maximum eye closure (EC). We showed that the allowable DGD depends on the time slot for one bit T, which is the inverse of the network bit rate. Wider T is more immune to large PMD with the EC still maintained at the same level since DGD/T is unchanged. Our analysis also indicated that as DGD increases, BER increases. The BER also increases with increase in PDL and further increases with the presence of XPM, SPM, FWM, and CD.     

The Effects of Polarization and Non-Linearity on the Performance of WDM System with Optical Cross-Connects

The performance of a wavelength division multiplexing (WDM) system with optical cross-connects (OXCs) and in the presence of polarization and nonlinear effects was analyzed. We determined the effect of PMD and PDL; nonlinearity such as XPM, SPM, and FWM; and CD on the system performance. We found that the system outage probability is highest at DGD threshold for the respective maximum eye closure (EC). We showed that the allowable DGD depends on the time slot for one bit T, which is the inverse of the network bit rate. Wider T is more immune to large PMD with the EC still maintained at the same level since DGD/T is unchanged. Our analysis also indicated that as DGD increases, BER increases. The BER also increases with increase in PDL and further increases with the presence of XPM, SPM, FWM, and CD.     

化学发光法测定巯嘌呤的含量

在流动注射系统中,利用巯嘌呤在碱性Luminol-K₃Fe(CN)₆化学发光体系中发光信号强的特点,建立了一种测定巯嘌呤的新方法。在优化条件下,方法的线性范围是1.02×10-7～1.02×10-9mol·L-1, 回归方程是Y=36.315c+140.72(Y是相对发光强度,c是巯嘌呤浓度与10-8 mol·L-1的乘积), 相关系数是0.998 2,检出限(S/N=3)是6.33×10-10mol·L-1,RSD为3.54%（c_i=2.0×10-9mol·L-1, n=12）。该法用于合成样品的测定,简便、灵敏、快速,结果令人满意。文章简要地探讨了巯嘌呤在碱性Luminol-K₃Fe(CN)₆化学发光体系中的化学发光机理：在反应过程中,产生大量的过氧自由基和羟基自由基,自由基与鲁米诺反应,形成激发态的鲁米诺分子,鲁米诺分子由激发态回到基态产生化学发光现象。