Aerosol assisted synthesis of silica/phenolic resin composite mesoporous hollow spheres

Hollow spheres of phenolic resin/silica composite are synthesized by macroscopic phase separation of a sorbitan monooleate surfactant Span 80 during aerosol-assisted spraying. The cavity can be evolved from multiple compartments to single hollow cavity with the increase of Span 80 content. The composite shell becomes mesoporous due to the release of small molecules after thermal treatment above 350 °C. After further thermal treatment at a higher temperature for example 900 °C in nitrogen or 1,450 °C in argon, the carbon/silica composite hollow spheres or crystalline silicon carbide hollow spheres are derived, respectively. Compared to the pure phenolic resin-based carbon spheres, thermal stability of the carbon-based composite spheres in air is essentially improved by the introduction of inorganic component silica. The carbon-based composite hollow spheres combine both performances of easy mass transportation through macropores and high specific surface area of mesopores, which will be promising to support catalysts for fuel cells. Electronic supplementary material  The online version of this article (doi:) contains supplementary material, which is available to authorized users.     

Formation of hollow silica spheres from molecular silica sols

1. Download : Download high-res image (117KB)
2. Download : Download full-size image

     

Synthesis of micron-sized hollow silica spheres with a novel mesoporous shell of MCF

Micron-sized hollow silica spheres whose shells are made up of mesocellular silica foams(MCFs) have been synthesized by one-pot sol-gel method in benzene/water/P123 emulsion.The material is characterized with SEM,TEM,BET and ~(29)Si MAS NMR. The results show that the MCFs of the unique shell of hollow silica spheres were connected by large windows with a narrow distribution of～10 nm in diameter,the inner space of the hollow sphere is accessible.And the formation mechanism of the hollow silica spheres is ...     

Synthesis of hollow silica spheres with mesostructured shell using cationic-anionic-neutral block copolymer ternary surfactants

Hollow silica spheres with mesostructured shells (HSSMS) were prepared with a vesicle template of cetyltrimethylammonium bromide-sodium dodecyl sulfate-Pluronic P123 (C(16)TMAB-SDS-EO(20)PO(70)EO(20)) at a SDS/C(16)TMAB ratio of 0.6-0.8 following a fast silicification in dilute silicate solution at pH approximately 5.0. The mesostructure of the shell is disordered, and the mesopore size is about 5.5-7.5 nm. Moreover, the direction and length of the nanochannels of the shell change with the SDS/C(16)TMAB ratios. A bi-template model, in which the C(16)TMA(+)-DS(-) form the stable bilayer vesicle structure and the P123 copolymers anchored on C(16)TMA(+)-DS(-) vesicle act as the template for the mesoporous silica, was proposed to explain the formation of the HSSMS. This bi-template model can be applied extensively to prepare the HSSMS with different diameters and pore sizes by using other C(n)TMAX-SDS-EO(n)PO(m))EO(n) ternary-surfactant mixtures.     

Hydrothermal synthesis of hollow silica spheres under acidic conditions

It is well-known that silica can be etched in alkaline media or in a unique hydrofluoric acid (HF) solution, which is widely used to prepare various kinds of hollow nanostructures (including silica hollow structures) via silica-templating methods. In our experiments, we found that sto?ber silica spheres could be etched in generic acidic media in a well-controlled way under hydrothermal conditions, forming well-defined hollow/rattle-type silica spheres. Furthermore, some salts such as NaCl and Na(2)SO(4) were found to be favorable for the formation of hollow/rattle-type silica spheres.     

Architecture of micron-scale hollow spheres composed of silica nanoparticles and approach to luminescent spheres

Micron-scale hollow spheres were successfully constructed with silica nanoparticles by templating of polymer spheres. Subsequently, the use of 3-aminopropyltriethoxysilane (APTES) introduces carbon and oxygen defects in the silica nanoparticles resulting from calcination of the aminopropyl group. In this approach, the template of micron-scale polymer spheres was prepared from dispersion polymerization. Subsequent St?ber process results in the formation of a silica layer attached to the polymer sphere surfaces. After calcination, the obtained micron-scale hollow silica spheres were then studied on the relationship between the particle diameter and the surface morphology. The luminescence of hollow spheres was prepared through using APTES in St?ber process, and which of related the appearance of luminescence to the APTES concentration and calcination temperature. The results of this study can provide useful information for the structure of micron-scale hollow spheres and their application to luminescent materials.     

A facile method of synthesis of asymmetric hollow silica spheres

This paper presents a "one-step" method to synthesize asymmetric hollow silica spheres. In this method, when positively charged polystyrene particles were blended with mercaptopropyltriethoxysilane and stirred at 50 °C in alkaline ethanol/water medium for a period of time, Janus or lobed asymmetric hollow silica spheres could be directly obtained, just changing the ratio of ethanol to water in the reaction medium. Transmission electron microscopy (TEM) and scanning electron microscopy (SEM) were used to characterize the morphology and topography of the asymmetric hollow silica spheres. The formation mechanism was described in detail.     

Mesoporous hollow silica spheres as micro-water-tanks in proton exchange membranes

In order to decrease the swelling of Nafion^® and reduce the dependency of proton conductivity on high relative humidity (RH), mesoporous hollow silica spheres were synthesized and dispersed in Nafion matrix as micro-water-tanks in the proton exchange membranes (PEM). The morphologies of MHSi and Nafion/MHSi composite membranes are characterized by SEM and TEM. The effects of MHSi on water uptake, swelling, dehydration rate and proton conductivity of the composite membranes were investigated. The results show that, with a suitable portion of MHSi in the membrane, composite PEMs with enhanced water uptake, reduced swelling and improved proton conductivity are obtained.     

A novel approach to produce monodisperse hollow pure silica spheres

In this work, we report an efficient method to produce pure hollow silica spheres (HSS) using phenyltrimethoxysilane (PTMS) compound. The production of HSS was carried out via hydrolysis of PTMS in the aqueous media and followed by a condensation reaction to form silica spheres with phenyl groups. The product was then calcined to remove phenyl groups and obtain pure silica spheres with >95% fine structure. The chemical nature of pure silica was confirmed by Fourier transforms infrared spectroscopy. The calcined HSS were stable beyond the temperature of 900 °C as confirmed by thermal gravimetric analysis (TGA). The calcined spheres preserved their spherical appearance and hollow core as shown by SEM and TEM micrographs. Interestingly, the average size of the spheres was reduced significantly after calcination from 760 to 510 nm, confirming further the removal of phenyl groups. The calcined HSS offered much higher surface area (A_s) when analysed by BET; A_s for calcined product was ～406 and mere ～4.8 m²/g for uncalcined HSS. Finally, drug release study of cisplatin/HSS showed over 45% of steady cumulative release for 72 h. The prepared HSS can be dispersed in water opening the possibility of many novel bio/non-bio applications.     

Synthesis of hollow silica spheres with hierarchical shell structure by the dual action of liquid indium microbeads in vapor-liquid-solid growth

Geometry-based adhesion arising from hierarchical surface structure enables microspheres to adhere to cells strongly, which is essential for inorganic microcapsules that function as drug delivery or diagnostic imaging agents. However, constructing a hierarchical structure on the outer shell of the products via the current microcapsule synthesis method is difficult. This work presents a novel approach to fabricating hollow microspheres with a hierarchical shell structure through the vapor-liquid-solid (VLS) process in which liquid indium droplets act as both templates for the formation of silica capsules and catalysts for the growth of hierarchical shell structure. This hierarchical shell structure offers the hollow microsphere an enhanced geometry-based adhesion. The results provide a facile method for fabricating hollow spheres and enriching their function through tailoring the geometry of their outer shells.     

Preparation and properties of Nafion/hollow silica spheres composite membranes

In present work, hollow silica spheres (HSS)/Nafion^® composite membranes were prepared by solution casting. The thermal properties, water retention, swelling behavior and proton conductivity of the composite membranes were explored. It was found that HSS dispersed well at micrometer scale in the obtained composite membranes by SEM and TEM observation. Thermal properties of composite membranes were improved than that of recast Nafion^® membrane. Compared with the recast Nafion^® membrane, the composite membranes showed higher water uptake and lower swelling degree at the temperature range from 40 to 100 °C. At the same HSS loading, the smaller the diameter of HSS in composite membranes, the more the water uptake, however, the swelling degree of composite membranes was increased. The proton conductivity of the composite membrane with 3–5 wt.% HSS (120 and 250 nm) increased distinctively at above 60 °C, reached the optimal value at 100 °C, and decreased slowly when the temperature exceeded 100 °C.     

A novel method for the fabrication of monodisperse hollow silica spheres

In this paper, we report a novel method for the fabrication of small monodisperse hollow silica spheres. In this approach, when silica shells were coated on polystyrene particles by the sol-gel method, the polystyrene cores were dissolved subsequently, even synchronously, in the same medium to form monodisperse hollow spheres. Neither additional dissolution nor a calcination process was needed to remove the polystyrene cores. Transmission electron microscopy, scanning electron microscopy, and porosity measurements were used to characterize the monodisperse hollow silica spheres.     

以手性两亲小分子自组装体为模板制备介孔二氧化硅空心球

合成了手性阳离子型两亲性小分子化合物,利用圆二色谱分析了其在水中形成的自组装体的结构;以该化合物的自组装体为模板,在正丙醇和氨水的混合溶剂中制备得到了介孔二氧化硅空心球;利用扫描电镜、透射电镜、X射线衍射仪以及氮气吸附-脱附试验装置分析了二氧化硅空心球的形貌及孔结构.结果表明,两亲性小分子在水中形成的自组装体呈现手性堆积;合成的介孔二氧化硅空心球的直径约为600~800nm,壁厚约为100~150nm,其孔道垂直于球的表面,孔径约为3.0nm,比表面积约为306m2·g-1.正丙醇作为模板控制二氧化硅空心球的空腔尺寸和形貌,而两亲性小分子的自组装体作为模板控制放射状孔道的形貌和尺寸.     

Needle-like calcium carbonate assisted self-assembly of mesostructured hollow silica nanotubes

Mesostructured hollow silica nanotubes (MHSNTs) were successfully produced via the self-assembly of C₁₆TMABr and silica species on the surface of needle-like calcium carbonate nanoparticles in an alkaline medium at room temperature. The characterization of MHSNTs by transmission electron microscopy (TEM), scanning electron microscopy (SEM), pore size distribution (PSD) and Brunauer-Emmett-Teller (BET) indicated that MHSNTs had uniform tubular hollow structures with big openings, a length of 1.5-2.0 μm, an inner diameter of 150-200 nm at the open end and 50-60 nm at the closed end, and a wall thickness of 20-30 nm, as well as a narrow PSD around 2.3 nm in the shells and a BET surface area as high as ∼975.3 m²/g. By small-angle X-ray diffraction (XRD), BET and pore structure analysis, it was found that more uniformly structured mesopores could be formed by the method of removing the double templates simultaneously through a solvent extraction process, as compared to the separate removal of the double templates by calcinating and then etching in an acidic solution, and the amount of C₁₆TMABr affected the mesoporous structures of MHSNTs greatly. The formation processes of MHSNTs were also studied with XRD and FTIR.     

Fabrication linalool-functionalized hollow mesoporous silica spheres nanoparticles for efficiently enhance bactericidal activity

To develop a novel food preservation technology for efficiently enhance bactericidal activity in a long term, hollow mesoporous silica spheres (HMSS) with regular nanostructures were applied to encapsulate natural organic antimicrobial agents. The chemical structures, morphologies and thermal stabilities of linalool, HMSS and linalool-functionalized hollow mesoporous silica spheres (L-HMSS) nanoparticles were evaluated by polarimeter, field emission scanning electron microscope (FE-SEM), transmission electron microscope (TEM), fourier transform infrared (FT-IR), thermal gravimetric analyzer (TGA), nitrogen adsorption-desorption, zeta potential and small angle X-ray diffraction (SXRD). The results show that the linalool was successfully introduced into the cavities of HMSS, and the inorganic host exhibited a high loading capacity of about 1500 mg/g. In addition, after 48 h of incubation, the minimum bactericidal concentrations (MBC) of L-HMSS against Escherichia coli (E. coli), Salmonella enterica (S. enterica) and Staphylococcus aureus (S. aureus), Listeria monocytogenes (L. monocytogenes) were decreased to be 4 (< 5) mg/mL and 8 (< 10) mg/mL, respectively. These results revealed linalool-functionalized hollow mesoporous spheres could efficiently improve the bactericidal activities of the organic component. Furthermore, SEM images clearly showed that L-HMSS indeed had an extremely inhibitory effect against gram-negative (E. coli) and gram-positive (S. aureus) by breaking the structure of the cell membrane. This research is of great significance in the application of linalool in nano-delivery system as well as food industry.     

Fabrication of hollow silica spheres using droplet templates derived from a miniemulsion technique

Hollow silica spheres have been successfully fabricated by means of a miniemulsion technique, in which miniemulsion droplets of tetraethoxysilane (TEOS) and octane were prepared with cetyltrimethylammonium bromide as a surfactant and hexadecane as a costabilizer and used as templates. As the TEOS diffused out from the droplets, it was hydrolyzed and condensed to form a silica shell at the oil/water interface. In this way, hollow silica spheres could be obtained directly since the miniemulsion droplets of octane could be evaporated very easily during the reaction process or the drying process; neither an additional dissolution nor a calcination process or additional surface modification of the templates were needed.     

Fabrication of silica nanoparticles and hollow spheres using ionic liquid microemulsion droplets as templates

Silica products with two different morphologies were synthesized using nonaqueous ionic liquid microemulsion droplets as templates. The morphologies of the obtained products were characterized by both transmission electron microscopy (TEM) and scanning electron microscopy (SEM). By adjusting the reaction conditions, ellipsoidal nanoparticles were formed under acidic conditions, while hollow silica spheres were obtained under alkaline conditions. It is demonstrated that the size distribution of hollow silica spheres was narrower than that of the ellipsoidal nanoparticles. The various vibration modes of different functional groups in the silica materials were revealed by Fourier transform infrared (FTIR) spectroscopy. The two samples were both shown to be amorphous, not crystalline by X-ray diffraction (XRD). A simple diagram of the formation process including the hydrolysis and condensation reactions is given. Furthermore, a probable mechanism for the formation of silica materials under acidic or alkaline conditions is presented, which may be helpful for better understanding the different silica materials obtained under different conditions.     

Synthesis of penetrable macroporous silica spheres for high-performance liquid chromatography

Silica microspheres have been synthesized by phase separation and sol–gel transition coupled with emulsion method. The as-obtained material is characterized by scanning electron microscopy, nitrogen sorption, elemental analysis and particle size distribution measurements. The results demonstrated that the material featured with hierarchically porous structure, possessing both mesopores and penetrable macropores. The mesopores provide large surface area while the macropores traverse the silica particles, which may facilitate fast mass transfer as well as guarantee low backpressure when such materials are used for packed high-performance liquid chromatography (HPLC) column. Therefore, their preliminary applications as HPLC packings in fast separation and low-pressure separation have been attempted in the present study. Benzene, benzaldehyde and benzyl alcohol were separated within two minutes on the silica column at a flow rate of 7 mL min⁻¹. Vitamin E mixtures can also be baseline separated at a high flow rate of 8 mL min⁻¹. In addition, thirteen aromatic hydrocarbons were well separated on the octadecyl-bonded silica (ODS) column. In comparison with a commercial Kromasil ODS column, the pressure of the proposed column is much lower (<1/2) under the same chromatographic conditions, while comparable separation efficiency can be achieved.