Oil-in-water emulsions stabilized by hydrophobically modified hydroxyethyl cellulose: adsorption and thickening effect

The preparation and stability of oil-in-water emulsions stabilized by hydrophobically modified hydroxyethyl cellulose (HMHEC) were investigated. The rheological measurements of aqueous HMHEC were studied. It was found that HMHEC showed much better thickening ability than the parent (HEC) from which it was derived, which is caused by the association of the hydrophobic alkyl chains, which are absent in HEC. The oscillatory experimental results of the emulsions showed that at higher concentrations, HMHEC could form an elastic gel, which has good thixotropic properties. The stability and droplet size distribution were investigated by visual observation, photomicrograph and a laser-scattering particle size distribution analyzer. The adsorption of HMHEC at the oil-water interface and the surface of emulsion droplets due to the penetration of the alkyl chains in HMHEC into the oil phase were confirmed by visual observation, the interfacial tension method and an in situ environmental scanning electron microscope (ESEM). The stability of emulsions prepared using HMHEC is based on both an associative thickening mechanism caused by alkyl chains in HMHEC and the adsorption of HMHEC at the oil-water interface, which can form a solid film preventing coalescence of the droplets.     

Thickening properties and emulsification mechanisms of new derivatives of polysaccharide in aqueous solution 2. The effect of the substitution ratio of hydrophobic/hydrophilic moieties

The thickening properties and association behavior of aqueous solutions of HHM-HEC (hydrophobically-hydrophilically modified hydroxyethyl cellulose) with various hydrophobic and hydrophilic substitution degrees were investigated. The HHM-HEC was used as an oil-in-water emulsifier and stable compositional regions were investigated as a function of polymer concentration and substitution degree. The viscosity of aqueous solutions of HHM-HEC increased drastically at lower concentration for HHM-HEC with a higher hydrophobic/hydrophilic substitution ratio. The intensity ratio of the first and third vibrational bands of pyrene (I(1)/I(3)) decreased with the increase of HHM-HEC concentration and the I(1)/I(3) reached a lower plateau at a lower concentration for HHM-HEC with a higher hydrophobic/hydrophilic substitution ratio. The concentration ranges of HHM-HEC solutions which stabilize O/W emulsions differ by the hydrophobic/hydrophilic substitution ratio. However the viscosity ranges of these HHM-HEC solutions were almost the same regardless of the hydrophobic/hydrophilic substitution ratio. At the suitable concentration range for emulsification, HHM-HEC networks have two properties: (1) oil particle retention capacity and (2) laxation which can trap emulsified particles.     

Effect of the type of the oil phase on stability of highly concentrated water-in-oil emulsions

The water-in-oil high internal phase emulsions were the subject of the study. The emulsions consisted of a super-cooled aqueous solution of inorganic salt as a dispersed phase and industrial grade oil as a continuous phase. The influence of the industrial grade oil type on a water-in-oil high internal phase emulsion stability was investigated. The stability of emulsions was considered in terms of the crystallization of the dispersed phase droplets (that are super-cooled aqueous salt solution) during ageing. The oils were divided into groups: one that highlighted the effect of oil/aqueous phase interfacial tension and another that investigated the effect of oil viscosity on the emulsion rheological properties and shelf-life. For a given set of experimental conditions the influence of oil viscosity for the emulsion stability as well as the oil/aqueous interfacial tension plays an important role. Within the frames of our experiment it was found that there are oil types characterized by optimal parameters: oil/aqueous phase interfacial tension being in the region of 19–24 mN/m and viscosity close to 3 mPa s; such oils produced the most stable high internal phase emulsions. It was assumed that the oil with optimal parameters kept the critical micelle concentration and surfactant diffusion rate at optimal levels allowing the formation of a strong emulsifier layer at the interface and at the same time creating enough emulsifier micelles in the inter-droplet layer to prevent the droplet crystallization.     

Mechanism of oil-in-water emulsification using a water-soluble amphiphilic polymer and lipophilic surfactant

A new O/W (oil-in-water) emulsification system was developed using the amphiphilic polymer HHM-HEC (hydrophobically-hydrophilically modified hydroxyethylcellulose) and a lipophilic surfactant. HHM-HEC was used as a thickener and polymeric surfactant, and the addition of small quantities of various types of nonionic lipophilic surfactant (hydrophilic-lipophilic balance <5) decreased the droplet size of several types of oil due to a lowering of the tension at the water/oil interface. The oil droplets were held by the strong network structure of the aqueous HHM-HEC solution, preserving the O/W phase without inversion. These stable O/W emulsions were prepared without the addition of hydrophilic surfactants and thus show improved water repellency.     

Relationship between rheological properties and one-step W/O/W multiple emulsion formation

Formation of a normal (not temporary) W/O/W multiple emulsion via the one-step method as a result of the simultaneous occurrence of catastrophic and transitional phase inversion processes has been recently reported. Critical features of this process include the emulsification temperature (corresponding to the ultralow surface tension point), the use of a specific nonionic surfactant blend and the surfactant blend/oil phase ratio, and the addition of the surfactant blend to the oil phase. The purpose of this study was to investigate physicochemical properties in an effort to gain a mechanistic understanding of the formation of these emulsions. Bulk, surface, and interfacial rheological properties of adsorbed nonionic surfactant (CremophorRH40 and Span80) films were investigated under conditions known to affect W/O/W emulsion formation. Bulk viscosity results demonstrated that CremophorRH40 has a higher mobility in oil compared than in water, explaining the significance of the solvent phase. In addition, the bulk viscosity profile of aqueous solutions containing CremophorRH40 indicated a phase transition at around 78 ± 2 °C, which is in agreement with cubic phase formation in the Winsor III region. The similarity in the interfacial elasticity values of CremophorRH40 and Span80 indicated that canola oil has a major effect on surface activity, showing the significance of vegetable oil. The highest interfacial shear elasticity and viscosity were observed when both surfactants were added to the oil phase, indicating the importance of the microstructural arrangement. CremophorRH40/Span80 complexes tended to desorb from the solution/solution interface with increasing temperature, indicating surfactant phase formation as is theoretically predicted in the Winsor III region. Together these interfacial and bulk rheology data demonstrate that one-step W/O/W emulsions form as a result of the simultaneous occurrence of phase-transition processes in the Winsor III region and explain the critical formulation and processing parameters necessary to achieve the formation of these normal W/O/W emulsions.     

Polyols,High Pressure,and Refractive Indices Equalization for Improved Stability of W/O Emulsions for Food Applications

Mixtures of polyols (glycerol, propylene glycol, glucose) and water were emulsified in oil (isopropyl myristate (IPM), medium chain triglycerides (MCT), long chain triglycerides (LCT), and d-limonene) under elevated pressures and homogenization, in the presence of polyglycerol polyricinoleate (PGPR), glycerol monooleate (GMO), and their mixture as emulsifiers to form water-in-oil emulsions. High pressures was applied to: a) the emulsion, b) the aqueous phase and c) the oil phase in the presence of the emulsifiers (PGPR and GMO). Under optimal pressure (2000 atms) applied to the ready-made emulsion or to the aqueous phase prior to its emulsification, and with optimal composition (30wt% polyol in the aqueous phase and MCT as the oil phase), the aqueous droplets were stable for months and submicron in size (0.1 μm). Moreover, due to equalization of the oil and the aqueous phases refractive indices, the emulsions were almost transparent. Pressure and polyols have synergistic effects on the emulsions stability. During preparation, surface tensions and interfacial tensions were dramatically reduced until an optimal water/polyols ratio was achieved, which allows rupturing of the droplets to submicronal size (0.1 μm) without recoalescence and fast diffusion to the interface. These unique W/O emulsions are suitable for preparing W/O/W double emulsions for sustained release of active materials for food applications.     

Double inversion of emulsions induced by salt concentration

The effects of salt on emulsions containing sorbitan oleate (Span 80) and Laponite particles were investigated. Surprisingly, a novel double phase inversion was induced by simply changing the salt concentration. At fixed concentration of Laponite particles in the aqueous phase and surfactant in paraffin oil, emulsions are oil in water (o/w) when the concentration of NaCl is lower than 5 mM. Emulsions of water in oil (w/o) are obtained when the NaCl concentration is between 5 and 20 mM. Then the emulsions invert to o/w when the salt concentration is higher than 50 mM. In this process, different emulsifiers dominate the composition of the interfacial layer, and the emulsion type is correspondingly controlled. When the salt concentration is low in the aqueous dispersion of Laponite, the particles are discrete and can move to the interface freely. Therefore, the emulsions are stabilized by particles and surfactant, and the type is o/w as particles are in domination. At intermediate salt concentrations, the aqueous dispersions of Laponite are gel-like, the viscosity is high, and the transition of the particles from the aqueous phase to the interface is inhibited. The emulsions are stabilized mainly by lipophilic surfactant, and w/o emulsions are obtained. For high salt concentration, flocculation occurs and the viscosity of the dispersion is reduced; thus, the adsorption of particles is promoted and the type of emulsions inverts to o/w. Laser-induced fluorescent confocal micrographs and cryo transmission electron microscopy clearly confirm the adsorption of Laponite particles on the surface of o/w emulsion droplets, whereas the accumulation of particles at the w/o emulsion droplet surfaces was not observed. This mechanism is also supported by the results of rheology and interfacial tension measurements.     

Characterization of Optical Properties in Water-in-Oil Emulsion

There have been few studies on the factors that determine the overall appearance of emulsions. Optical properties are quite important in determining the perceived quality of emulsion-based products. The overall appearance of an emulsion is determined by the way that it interacts with electromagnetic radiation in the visible region of the spectrum, for example, reflection, transmission, adsorption, and scattering. These interactions are principally determined by the characteristics of emulsion droplets (size, concentration, and refractive index). The present study aims at characterizing the optical properties and rheological behaviors of water-in-oil emulsions, especially macroemulsions. There is a decrease in the absorbance spectra as increasing glycerin ratio in aqueous phase because the difference of refractive index between oil phase and aqueous phase decreased, which improved the transparency of water-in-oil emulsion. The absorbance of linear and branched surfactant emulsions were smaller than that of alkyl modified branched surfactant emulsion. Moreover the transparency of emulsions prepared with linear and branched surfactants was much clearer than that of alkyl modified branched surfactant emulsion. The absorbance spectra also showed that low polar oil attributed to the more transparent emulsion, compared with high polar or nonpolar oil. However, these kinds of oils were not helpful to prepare transparent emulsion because the appearance of these emulsions was translucent or opaque, even if polyols in aqueous phase was 30 wt%.     

Some aspects of stability of multiple emulsions in personal cleansing systems

The two dominant factors that were found to affect the stability of multiple emulsions in high HLB surfactant systems are the osmotic pressure imbalance between the internal aqueous phase and the external aqueous phase, and the adsorption/desorption characteristics of the emulsifier/surfactant film at the oil/water interface. Synergistic interaction between the low HLB emulsifier and the high HLB surfactant that produces very low interfacial tension of the order of 10(-2) mN/m at the oil/water interface was found to occur in some of the systems investigated. Long term stability was observed in multiple emulsion containing these systems. However, no synergy was observed in systems in which either the oil or the emulsifier, or both, contained unsaturated chains. In fact, desorption of the adsorbed surfactant film was observed in systems containing unsaturated chains. The observed desorption from the interface of the emulsifier in these systems was attributed mainly to the inability of the unsaturated chains to form a close packed, condensed interfacial film. Presence of closely packed, condensed interfacial film is necessary to prevent solubilization of the adsorbed low HLB emulsifier by the high HLB surfactant. Multiple emulsions prepared using systems containing unsaturated hydrocarbons were highly unstable.     

Interfacial and Emulsion Stabilizing Properties of Indigenous Acidic and Esterified Asphaltenes

This article describes interfacial properties of acidic asphaltenes and their ability to stabilize emulsions. Asphaltenes extracted from crude oil were esterified with methanol to prevent ionization of carboxylic acid at high pH. Interfacial tension (IFT) between water and asphaltenes in xylene was significantly lower in basic than in acidic and neutral media, while the elasticity of the corresponding films was higher. These results are consistent with much more stable asphaltene-based emulsions in basic medium. For ester-asphaltenes, the IFT only showed a slight decrease under basic conditions and the interfacial elasticity was close to that in acidic solutions and only slightly higher than for neutral medium. While the asphaltene-stabilized emulsions showed a strong increase in stability in basic medium, this increase was much less for ester-asphaltene emulsions. Salt influenced the interfacial properties and generally reduced emulsion stability.     

Influence of hydrophobic groups on thickening and emulsification properties of hydrophobically modified polyacrylamides

Hydrophobically modified polyacrylamides can be used to enhance oil recovery in tertiary oil recovery process because they have good thickening and emulsification properties. Hydrophobically modified polyacrylamides with different hydrophobic groups were synthesized using micellar polymerization. Above CAC, elastic polymer gel is formed by the aggregation of hydrophobic groups. Hydrophobicity of hydrophobic groups plays a substantially important role in properties of HMPAMs solutions. Higher hydrophobicity of hydrophobic groups leads to more intensive intermolecular association and thus helps to enhance the apparent viscosity of HMPAMs solutions and form stronger elastic polymer gel network structures in HMPAMs solutions which can enhance the stability of the O/W crude oil emulsions stabilized by HMPAMs.     

Stability of Water/Crude Oil Systems Correlated to the Physicochemical Properties of the Oil Phase

A characterization of 30 crude oils has been performed to determine the relative level of influence that individual parameters have over the overall stability of w/o emulsions. The crude oils have been analyzed with respect to bulk and interfacial properties and the characteristics of their w/o emulsions. The parameters include compositional properties, acidity, spectroscopic signatures in the infrared and near‐infrared region, density, viscosity, molecular weight, interfacial tension, dilational relaxation, droplet size distribution, and stability to gravitationally and electrically induced separation. As expected, a strong covariance between several physicochemical properties was found. Near‐infrared spectroscopy proved to be an effective tool for crude oil analysis. In particular, we have showed the importance of the hydrodynamic resistance to electrically‐induced separation (static) in heavy crude oil‐water emulsions. A rough estimate of the drag forces and dielectrophoretic forces seemed to capture the difference between the 30 crude oils. Given enough time, water‐in‐heavy oil emulsions could be destabilized even at very low electric field magnitude (d.c.). When droplets approach each other in an inhomogeneous electric field, strong dielectrophoretic forces disintegrate the films and result in coalescence. The relative contribution from film stability to the overall emulsion stability may therefore be very different in a gravitational field compared to that in an electrical field.     

Interface composition of multiple emulsions: rheology as a probe

We have investigated the dynamic rheological properties of concentrated multiple emulsions to characterize their amphiphile composition at interfaces. Multiple emulsions (W1/O/W2) consist of water droplets (W1) dispersed into oil globules (O), which are redispersed in an external aqueous phase (W2). A small-molecule surfactant and an amphiphilic polymer were used to stabilize the inverse emulsion (W1 in oil globules) and the inverse emulsion (oil globules in W2), respectively. Rheological and interfacial tension measurements show that the polymeric surfactant adsorbed at the globule interface does not migrate to the droplet interfaces through the oil phase. This explains, at least partly, the stability improvement of multiple emulsions as polymeric surfactants are used instead of small-molecule surfactants.     

Formation of liquid crystal/gel emulsions to nano-emulsions constructed by polyalkoxylated fatty alcohol (PAFA)-based mixed surfactant systems

In the construction of ternary phase diagrams, the polyalkoxylated fatty alcohol (PAFA)-based mixed surfactant systems including PAFA-AS (alkyl sulfonate), PAFA-CB (cocamidopropyl betaine) and PAFA-APG (alkyl polyglucosides) were used to develop self-standing liquid crystal/gel emulsions containing rapeseed oil methyl esters (ROME) and water. The formation of liquid crystal/gel emulsions are observed at semi-dilute regions of the phase diagrams. A pre-emulsion was chosen from each of PAFA-AS, PAFA-CB and PAFA-APG systems for minor modification with sodium silicate. Upon aqueous dilution of the modified pre-emulsions to weight fractions (Φ_w) of 0.8 and 0.6 and with an isothermal shaker agitation, the samples demonstrate dramatic increases in apparent viscosity with flow resistance and shear thinning behaviour. In oscillatory amplitude study, the emulsions show linear viscoelastic (LVE) plateau (G’>G”) and strain softening region (G”>G’) indicating the samples promote a viscoelastic behaviour. Further affirmation by Cole-Cole plots reveal the emulsion samples behave as a Maxwell fluid. The optical microscope study verifies the emulsions of PAFA-AS, PAFA-CB and PAFA-APG systems comprising of multilamellar vesicles, bicontinuous cubic phase and multilamellar phase, respectively. Upon aqueous dilution of the liquid crystal/gel emulsions with an isothermal agitation, the formation of nano-emulsion droplets is confirmed by transmission electron microscopy (TEM) and dynamic light scattering studies. The nano-emulsions display spherical and elliptical shapes with mean droplet sizes are in the range of 158.37 to 206.43?nm and zeta potential values are in the range of –12.07 to –32.79?mV.     

Influence of environmental stresses on stability of oil-in-water emulsions containing droplets stabilized by beta-lactoglobulin-iota-carrageenan membranes

An oil-in-water emulsion (5 wt% corn oil, 0.5 wt% beta-lactoglobulin (beta-Lg), 0.1 wt% iota-carrageenan, 5 mM phosphate buffer, pH 6.0) containing anionic droplets stabilized by interfacial membranes comprising of beta-lactoglobulin and iota-carrageenan was produced using a two-stage process. A primary emulsion containing anionic beta-Lg coated droplets was prepared by homogenizing oil and emulsifier solution together using a high-pressure valve homogenizer. A secondary emulsion containing beta-Lg-iota-carrageenan coated droplets was formed by mixing the primary emulsion with an aqueous iota-carrageenan solution. The stability of primary and secondary emulsions to sodium chloride (0-500 mM), calcium chloride (0-12 mM), and thermal processing (30-90 degrees C) were analyzed using zeta-potential, particle size and creaming stability measurements. The secondary emulsion had better stability to droplet aggregation than the primary emulsion at NaCl 相似文献   

Effect of molecular weight and degree of deacetylation of chitosan on the formation of oil-in-water emulsions stabilized by surfactant-chitosan membranes

The objective of this study was to establish the influence of polyelectrolyte characteristics (molecular weight and charge density) on the properties of oil-in-water emulsions containing oil droplets surrounded by surfactant-polyelectrolyte layers. A surfactant-stabilized emulsion containing small droplets (d32 approximately 0.3 microm) was prepared by homogenizing 20 wt% corn oil with 80 wt% emulsifier solution (20 mM SDS or 2.5 wt% Tween 20, 100 mM acetate buffer, pH 3) using a high-pressure valve homogenizer. This primary emulsion was then diluted with various chitosan solutions to produce secondary emulsions with a range of chitosan concentrations (3 wt% corn oil, 0-1 wt% chitosan). The influence of the molecular characteristics of chitosan on the properties of these emulsions was examined by using chitosan ingredients with different molecular weights (MW approximately 15, 145, and 200 kDa) and degree of deacetylation (DDA approximately 40, 77, and 92%). The electrical charge and particle size of the secondary emulsions were then measured. Extensive droplet aggregation occurred when the chitosan concentration was below the amount required to saturate the droplet surfaces, but stable emulsions could be formed at higher chitosan concentrations. The zeta-potential and mean diameter (d32) of the particles in the secondary emulsions was not strongly influenced by chitosan MW, however the chitosan with the lowest DDA (40%) produced droplets with smaller mean diameters and zeta-potentials than the other two DDA samples examined. Interestingly, we found that stable multilayer emulsions could be formed by mixing medium or high MW chitosan with an emulsion stabilized by a non-ionic surfactant (Tween 20) due to the fact the initial droplets had some negative charge. The information obtained from this study is useful for preparing emulsions stabilized by multilayer interfacial layers.     

Ethanol-in-oil emulsion (E/O) stabilized by polyglycerol polyricinoleate: A potential delivery system for ethanolic extract

This study evaluated how variations in polyglycerol polyricinoleate (PGPR) concentration and ethanol dispersed phase content affect the stability of ethanol-in-oil (E/O) emulsions. Results indicate that the stable 10?wt% E/O emulsions can be produced using 2?wt% PGPR. Increasing the ethanol dispersed phased content at constant PGPR concentration caused instability in emulsion. These emulsions remained stable to droplet flocculation and coalescence in the presence of Centella asiatica ethanol extract. PGPR does not greatly decrease the interfacial tension of the ethanol–oil interface. However, it adsorbed at the interface and stabilized the ethanol droplets in the emulsion via steric mechanism.     

Investigations into the electrical and coalescence behaviour of water-in-crude oil emulsions in high voltage gradients

The stability of water-in-crude oil emulsions when subjected to high voltage electric fields depends on the nature of the crude oil and the presence of chemical additives. Optical microscopy, conductivity and coalescence measurements have revealed two distinct types of behaviour, designated type I and type II. These are shown to be related to the crude oil/water interfacial rheological properties. For incompressible crude oil/water films, droplet—droplet coalescence is hindered and chains of water droplets are established. These increase the electrical conductivity of the emulsion (type I behaviour). On the other hand, efficient droplet—droplet coalescence accompanied by minimal conduction occurs in electric fields if the interfacial film is compressible (type II).     

Water-in-model oil emulsions studied by small-angle neutron scattering: interfacial film thickness and composition

The ever-increasing worldwide demand for energy has led to the upgrading of heavy crude oil and asphaltene-rich feedstocks becoming viable refining options for the petroleum industry. Traditional problems associated with these feedstocks, particularly stable water-in-petroleum emulsions, are drawing increasing attention. Despite considerable research on the interfacial assembly of asphaltenes, resins, and naphthenic acids, much about the resulting interfacial films is not well understood. Here, we describe the use of small-angle neutron scattering (SANS) to elucidate interfacial film properties from model emulsion systems. Modeling the SANS data with both a polydisperse core/shell form factor as well as a thin sheet approximation, we have deduced the film thickness and the asphaltenic composition within the stabilizing interfacial films of water-in-model oil emulsions prepared in toluene, decalin, and 1-methylnaphthalene. Film thicknesses were found to be 100-110 A with little deviation among the three solvents. By contrast, asphaltene composition in the film varied significantly, with decalin leading to the most asphaltene-rich films (30% by volume of the film), while emulsions made in toluene and methylnaphthalene resulted in lower asphaltenic contents (12-15%). Through centrifugation and dilatational rheology, we found that trends of decreasing water resolution (i.e., increasing emulsion stability) and increasing long-time dilatational elasticity corresponded with increasing asphaltene composition in the film. In addition to the asphaltenic composition of the films, here we also deduce the film solvent and water content. Our analyses indicate that 1:1 (O/W) emulsions prepared with 3% (w/w) asphaltenes in toluene and 1 wt % NaCl aqueous solutions at pH 7 and pH 10 resulted in 80-90 A thick films, interfacial areas around 2600-3100 cm (2)/mL, and films that were roughly 25% (v/v) asphaltenic, 60-70% toluene, and 8-12% water. The increased asphaltene and water film composition at pH 10 versus pH 7, along with unique dynamic interfacial tension profiles, suggested that the protonation state of carboxylic moieties within asphaltenes impacts the final film properties. This was further supported when we characterized similar asphaltenic emulsions that also contained 9-anthracence carboxylic acid (ACA). Addition of this aromatic acid led to slightly thinner films (70-80 A) that were characteristically more aqueous (up to 20% by volume) and 5-6% (v/v) ACA. This unique in situ characterization (deduced entirely from SANS data from emulsion samples) of the entire film composition calls for further investigation regarding the role this film-based water plays in emulsion stability.     

Stability of emulsions of water in mineral oils containing asphaltenes

Emulsions of water in mineral oils are stable if the oil phase contains asphaltenes which are near the condition of incipient flocculation. This condition is determined by the composition of the oil phase and by the nature of the asphaltenes. High aromaticity of the oil phase and the presence of deflocculants prevent flocculation of asphaltenes; the deflocculants may be interfacially active agents or asphaltene-like compounds with better solubility in the oil phase. Conditions of incipient flocculation of asphaltenes correlate very well with a considerable increase of rheological resistance of the interface between the oil phase and distilled water, determined according to the torsion oscillation method. Stabilization of the water-in-oil emulsions is therefore caused by the build-up of a coherent layer of asphaltenes in the water-oil interface in these cases. Deflocculants of asphaltenes in the oil phase destroy their stabilizing effect; however, the deflocculants themselves may stabilize the water-in-oil emulsions by adsorption on the water-oil interface and then the correlation between the condition of asphaltenes and emulsion stability does not hold, nor is the interfacial viscosity perceptibly increased. Under borderline conditions of emulsion stability a few percent of sodium chloride in the water phase counteracts the build-up of a stabilizing layer of asphaltenes in the water-oil interface and so do higher p_H values of a buffered water phase. At low p_H-values emulsion stability does not correlate with interfacial resistance. It can be concluded that asphaltenes stabilize water-in-oil emulsions if they accumulate on the water-oil interface. This interfacial layer may show a coherence, which is an indication of the presence of asphaltenes rather than a condition for stability of the emulsions.